The main focus of this thesis is placed on high frequency PCB signal Integrity Is-sues and RF/Microwave filters using EBG structures. From the signal Integrity aspect, two topics were mainly discussed. On one hand, the effect of increasing frequency on classical design rules for crosstalk reduction in PCBs was investigated experimentally and by full-wave simulations. An emphasis was placed on the 3×W spacing rule and the use of guard traces. Single-ended and differential transmission lines were considered. S-parameter measurements and simu-lations were carried out at high-frequency (up to 20 GHz). The results emphasize the necessity to reevaluate traditional design rules for their suitability in high frequency applications. Also, the impacts of using guard traces for high frequency crosstalk re-duction were clearly pointed out. On the other hand, the effect of high loss PCB ma-terials on the signal transmission characteristics of microstrip lines at high frequency (up to 20 GHz) was treated. Comparative studies were carried out on different micro-strip configurations using standard FR4 substrate and a high frequency dielectric ma-terial from Rogers, Corporation. The experimental results highlight the dramatic im-pact of high dielectric loss materials (FR4 and solder mask) and magnetic plating metal (nickel) on the high frequency signal attenuation and loss of microstrip trans-mission lines. Besides, the epoxy-based SU8 photoresist was characterized at high frequency (up to 50 GHz) using on-wafer conductor-backed coplanar waveguide transmission lines. A relative dielectric constant of 3.2 was obtained at 30 GHz. Some issues related to the processing of this material, such as cracks, hard-skin, etc, were also discussed. Regarding RF/Microwave filters, the concept of Electromagnetic Band Gap (EBG) was used to design and fabricate novel microstrip bandstop filters using periodically modified substrate. The proposed EBG structures, which don’t suffer conductor backing issues, exhibit interesting frequency response characteristics. The limitations of modeling and simulation tools in terms of speed and accuracy are also examined in this thesis. Experiments and simulations were carried out show-ing the inadequacies of the Spice diode model for the simulations in power electronics. Also, an Artificial Neural Network (ANN) model was proposed as an alternative and a complement to full-wave solvers, for a quick and sufficiently accurate simulation of interconnects. A software implementation of this model using Matlab’s ANN toolbox was shown to considerably reduce (by over 800 times) the simulation time of microstrip lines using full-wave solvers such as Ansoft’s HFSS and CST’s MWS. Finally, a novel cooling structure using a double heatsink for high performance electronics was presented. Methods for optimizing this structure were also discussed. / QC 20100809

The aim of this Master’s Degree thesis project is to design and develop point diffraction interferometer plates. In this project the PDI plates are re-designed, changing the design which was used in previous projects in Halmstad University. The transparency of PDI plates can be controlled by coating them with NiCr film. Firstly, four plates with coating of different thickness of NiCr were developed. The relationship between transmittance and the thickness of NiCr was established by testing these plates for transmittance and reflectance with the help of a laser and an optical power meter. The absorption coefficient of clear substrates and reflection of light is also taken into account to achieve the correct results. The parameters like the diameter of semi-transparent area around the pinholes and the size of pinholes is chosen after fully understanding its application. The lay-out and description of design is also included in the report.

<p>För att kalibrera väderradarna i Sverige finns en miniräknare med program som styr kalibreringen. Deluppgiften ”Program för kalibrering” innebär att överföra dessa program till en PC. Då ingen dokumentation finns om hur kommunikationen sker mellan radar och miniräknare, är första steget att analysera och jämföra programkoden från miniräknaren med informationen från en linjelyssnare. Därefter skrivs programmen i det grafiska programmeringsspråket Agilent Vee. Programmen läser av radarns svar på signaler med olika dämpning från en signalgenerator, beräknar en radarkonstant, skapar en kalibreringstabell, samt programmerar kalibreringstabellen i radarns signalprocessor. Datorns mätvärden och beräkningar jämförs med miniräknarens, och det kan konstateras att programmen överensstämmer med varandra.</p><p>Deluppgiften ”Automatiserad kontroll av dämpsteg” innebär att med en spektrumanalysator läsa av effekten på en signal med varierande dämpning från en signalgenerator. Detta görs för att kontrollera dämpstegen, då man på Saab Aerotech upptäckt problem med signalgeneratorn. Ett program skrivs för att automatiskt styra både signalgenerator och spektrumanalysator. Den avlästa effekten vid varje dämpsteg sparas och en graf med dessa värden genereras automatiskt av programmet. I grafen återfås en linjär kurva, vilket är det förväntade utseendet vid fungerande dämpsteg. För en ytterligare kontroll läses effekten av vid varje enskild dämpare. Även dessa värden ligger inom accepterade gränser, vilket innebär att problemet ligger på annat håll i signalgeneratorn, än i dämpstegen.</p> / <p>A calculator is used to calibrate all the weather radars in Sweden. One part of this thesis is to transfer the programs on this calculator to a PC. There is no documentation on how the calculator communicates with the radar, so the first step is to analyze and compare the code from the program with the information shown on a protocol analyzer. When the communication is known, a program is written in the language Agilent Vee. One program reads the response from the radar of a signal with different attenuation. Others calculates the radar constant, generates a calibration table and programs the table to the signal processor in the radar. By comparing the result from the programs on the PC and the corresponding results from the calculator it is verified that the programs run correctly.</p><p>Saab Aerotech have found that the signal generator in not working correctly. The other part of this thesis is to automatically control the signal generator and a spectrum analyzer. The spectrum analyzer reads the power of a signal with different attenuation from the signal generator and presents the values in a graph. The curve of the graph is linear which means that there is no problem with the attenuation.</p>

The dispersion property of periodic structures is a hot research topic in the last decade. By exploiting dispersion properties, one can manipulate the propagation of electromagnetic waves, and produce effects that do not exist in conventional materials. This thesis is devoted to two important dispersion effects: negative refraction and designed surface plasmons. First, we introduce negative refraction and designed surface plasmons, including a historical perspective, main areas for applications and current trends. Several numerical methods are implemented to analyze electromagnetic effects. We apply the layer-KKR method to calculate the electromagnetic wave through a slab of photonic crystals. By implementing the refraction matrix for semi-infinite photonic crystals, the layer-KKR method is modified to compute the coupling coefficient between plane waves and Bloch modes in photonic crystals. The plane wave method is applied to obtain the band structure and the equal-frequency contours in two-dimensional regular photonic crystals. The finite-difference time-domain method is widely used in our works, but we briefly discuss two calculation recipes in this thesis: how to deal with the surface termination of a perfect conductor and how to calculate the frequency response of high-Q cavities more efficiently using the Pad\`{e} approximation method. We discuss a photonic crystal that exhibits negative refraction characterized by an effective negative index, and systematically analyze the coupling coefficients between plane waves in air and Bloch waves in the photonic crystal. We find and explain that the coupling coefficients are strong-angularly dependent. We first propose an open-cavity structure formed by a negative-refraction photonic crystal. To illuminate the physical mechanism of the subwavelength imaging, we analyze both intensity and phase spectrum of the transmission through a slab of photonic crystals with all-angle negative refraction. It is shown that the focusing properties of the photonic crystal slab are mainly due to the negative refraction effect, rather than the self-collimation effect. As to designed surface plasmons, we design a structured perfectly conducting surface to achieve the negative refraction of surface waves. By the average field method, we obtain the effective permittivity and permeability of a perfectly conducting surface drilled with one-dimensional periodic rectangle holes, and propose this structure as a designed surface plasmon waveguide. By the analogy between designed surface plasmons and surface plasmon polaritons, we show that two different resonances contribute to the enhanced transmission through a metallic film with an array of subwavelength holes, and explain that the shape effect is attributed to localized waveguide resonances. / QC 20100817

The interaction of an HVDC converter with the connected power system is of complex nature. An accurate model of the converter is required to study these interactions. The use of analytical small-signal converter models provides useful insight and understanding of the interaction of the HVDC system and the connected system components. In this thesis analytical models of the HVDC converters are developed in the frequency-domain by calculating different transfer functions for small superimposed oscillations of voltage, current, and control signals. The objective is to study the dynamic proprieties of the combined AC-DC interaction and the interaction between different HVDC converters with small signal analysis. It is well known that the classical Bode/Nyquist/Nichols control theory provides a good tool for this purpose if transfer functions that thoroughly describe the 'plant' or the 'process' are available. Thus, there is a need for such a frequency-domain model. Experience and theoretical calculation have shown that voltage/power stability is a very important issue for an HVDC transmission link based on conventional line-commutated thyristor-controlled converters connected to an AC system with low short circuit capacity. The lower the short circuit capacity of the connected AC system as compared with the power rating of the HVDC converter, the more problems related to voltage/power stability are expected. Low-order harmonic resonance is another issue of concern when line-commutated HVDC converters are connected to a weak AC system. This resonance appears due to the presence of filters and shunt capacitors together with the AC network impedance. With a weak AC system connected to the HVDC converter, the system impedances interact through the converter and create resonances on both the AC- and DC-sides of the converter. In general, these resonance conditions may impose limitations on the design of the HVDC controllers. In order to improve the performance of the HVDC transmission system when it is connected to a weak AC system network, a reactive compensator with a voltage source converter has been closely connected to the inverter bus. In this thesis it is shown that the voltage source converter, with an appropriate control strategy, will behave like a rotating synchronous condenser and can be used in a similar way for the dynamic compensation of power transmission systems, providing voltage support and increasing the transient stability of the converter. / QC 20100708

The work presented in this thesis deals with optical studies of semiconductor quantum dots (QDs) in the InGaAs material system. It is shown that for self-assembled InAs QDs, the interaction with the surrounding GaAs barrier and the InAs wetting layer (WL) in particular, has a very large impact on their optical properties. The ability to control the charge state of individual QDs is demonstrated and attributed to a modulation in the carrier transport dynamics in the WL. After photo-excitation of carriers (electrons and holes) in the barrier, they will migrate in the sample and with a certain probability become captured into a QD. During this migration, the carriers can be affected by exerting them to an external magnetic field or by altering the temperature. An external magnetic field applied perpendicular to the carrier transport direction will lead to a decrease in the carrier drift velocity since their trajectories are bent, and at sufficiently high field strength become circular. In turn, this decreases the probability for the carriers to reach the QD since the probability for the carriers to get trapped in WL localizing potentials increases. An elevated temperature leads to an increased escape rate out of these potentials and again increases the flow of carriers towards the QD. These effects have significantly different strengths for electrons and holes due to the large difference in their respective masses and therefore it constitutes a way to control the supply of charges to the QD. Another effect of the different capture probabilities for electrons and holes into a QD that is explored is the ability to achieve spin polarization of the neutral exciton (X0). It has been concluded frequently in the literature that X0 cannot maintain its spin without application of an external magnetic field, due to the anisotropic electron – hole exchange interaction (AEI). In our studies, we show that at certain excitation conditions, the AEI can be by-passed since an electron is captured faster than a hole into a QD. The result is that the electron will populate the QD solely for a certain time window, before the hole is captured. During this time window and at polarized excitation, which creates spin polarized carriers, the electron can polarize the QD nuclei. In this way, a nuclear magnetic field is built up with a magnitude as high as ~ 1.5 T. This field will stabilize the X0 spin in a similar manner as an external magnetic field would. The build-up time for this nuclear field was determined to be ~ 10 ms and the polarization degree achieved for X0 is ~ 60 %. In contrast to the case of X0, the AEI is naturally cancelled for the negatively charged exciton (X-) and the positively charged exciton (X+) complexes. This is due to the fact that the electron (hole) spin is paired off in case of X- (X+).  Accordingly, an even higher polarization degree (~ 73 %) is measured for the positively charged exciton. In a different study, pyramidal QD structures were employed. In contrast to fabrication of self-assembled QDs, the position of QDs can be controlled in these samples as they are grown in inverted pyramids that are etched into a substrate. After sample processing, the result is free-standing AlGaAs pyramids with InGaAs QDs inside. Due to the pyramidal shape of these structures, the light extraction is considerably enhanced which opens up possibilities to study processes un-resolvable in self-assembled QDs. This has allowed studies of Auger-like shake-up processes of holes in single QDs. Normally, after radiative recombination of X+, the QD is populated with a ground state hole. However, at recombination, a fraction of the energy can be transferred to the hole so that it afterwards occupies an excited state instead. This process is detected experimentally as a red-shifted luminescence satellite peak with an intensity on the order of ~ 1/1000 of the main X+ peak intensity. The identification of the satellite peak is based on its intensity correlation with the X+ peak, photoluminescence excitation measurements and on magnetic field measurements. / Arbetet som presenteras i denna avhandling rör studier av kvantprickars optiska egenskaper. En kvantprick är en halvledarkristall som endast är några tiotals nanometer stor. Den ligger oftast inbäddad inuti en större kristall av ett annat halvledarmaterial och pga. den begränsade storleken får en kvantprick mycket speciella egenskaper. Bland annat så kommer elektronerna i en kvantprick endast att kunna anta vissa diskreta energinivåer liknande situationen för elektronerna i en atom. Följaktligen kallas kvantprickar ofta för artificiella atomer. För halvledarmaterial gäller det generellt att det inte endast är fria elektroner i ledningsbandet, som kan leda ström utan även tomma elektrontillstånd i valens­bandet, vilka uppträder som positivt laddade partiklar, kan leda ström. Dessa kallas kort och gott för hål. I en kvantprick har hålen såsom elektronerna helt diskreta energinivåer. Precis som är fallet i en atom, så kommer elektroniska övergångar mellan olika energi­nivåer i en kvantprick att resultera i att ljus emitteras. Energin (dvs. våglängden alt. färgen) för detta ljus bestäms av hur energinivåerna i kvant­pricken ligger, för elektronerna och hålen, och genom att analysera ljuset kan man således studera kvantprickens egenskaper. Studierna i den här avhandlingen visar att växelverkan mellan en kvantprick och den omgivande kristallen, som den ligger inbäddad i, har stor inverkan på kvantprickens optiska egenskaper. T.ex. visas att man kan kontrollera antalet elektroner, som kommer att finnas i kvantpricken genom att modifiera hur elektronerna kan röra sig i omgivningen. Dessa rörelser modifieras här genom att variera temperaturen och genom att lägga på ett magnetiskt fält. Ett magnetiskt fält, vinkelrätt mot en elektrons rörelse, kommer att böja av dess bana och dess chans att nå fram till kvantpricken kan således minskas. Elektronen kan då istället fastna i andra potentialgropar i kvantprickens närhet. Genom att öka temperaturen, vilket ger elektronerna större energi, kan deras chans att nå fram till kvantpricken å andra sidan öka. En annan effekt, som studerats, är möjligheten att kontrollera spinnet hos elektronerna i en kvantprick. Även i dessa studier visar det sig att växelverkan med omgivningen spelar stor roll och kan användas till att kontrollera elektronens spin. Mekanismen som föreslås är att om elektronerna hinner före hålen till kvantpricken, så hinner de överföra sitt spin till atomkärnorna i kvantpricken. På detta sätt kan man få atomkärnornas spin polariserat, vilket resulterar i ett inbyggt magnetfält, i storleksordningen 1.5 Tesla, som i sin tur hjälper till att upprätthålla en hög grad av spinpolarisering även hos elektronerna. För att få elektronerna att hinna först, måste deras rörelser i omgivningen kontrolleras. I en ytterligare studie undersöktes den process där en elektronisk övergång i kvantpricken inte enbart resulterar i emission av ljus, utan även i att en annan partikel tar över en del av energin och blir exciterad. Dessa processer avspeglas i att en del av det ljus som emitteras har lägre energi. Detta ljus är också mycket svagt, ca 1000 ggr lägre intensitet, och möjligheten att kunna mäta detta är helt beroende på hur ljusstarka kvantprickarna är. De prover som använts i denna studie består av pyramidstrukturer, ca 7.5 mikrometer stora, med kvantprickar inuti. Denna geometri ger ca 1000 ggr bättre ljusutbyte jämfört med traditionella strukturer, vilket möjliggjort studien.

This thesis deals with a system for operation of directly driven offshore wave energy converters. The work that has been carried out includes laboratory testing of a permanent magnet linear generator, wave energy converter mechanical design and offshore testing, and finally design, implementation, and offshore testing of an underwater collector substation. Long-term testing of a single point absorber, which was installed in March 2006, has been performed in real ocean waves in linear and in non-linear damping mode. The two different damping modes were realized by, first, a resistive load, and second, a rectifier with voltage smoothing capacitors and a resistive load in the DC-link. The loads are placed on land about 2 km east of the Lysekil wave energy research site, where the offshore experiments have been conducted. In the spring of 2009, another two wave energy converter prototypes were installed. Records of array operation were taken with two and three devices in the array. With two units, non-linear damping was used, and with three units, linear damping was employed. The point absorbers in the array are connected to the underwater substation, which is based on a 3 m3 pressure vessel standing on the seabed. In the substation, rectification of the frequency and amplitude modulated voltages from the linear generators is made. The DC voltage is smoothened by capacitors and inverted to 50 Hz electrical frequency, transformed and finally transmitted to the on-shore measuring station. Results show that the absorption is heavily dependent on the damping. It has also been shown that by increasing the damping, the standard deviation of electrical power can be reduced. The standard deviation of electrical power is reduced by array operation compared to single unit operation. Ongoing and future work include the construction and installation of a second underwater substation, which will connect the first substation and seven new WECs.

The author of this thesis concentrates his attention on quantum optical properties of some artificial electromagnetic media, such as quantum coherent atomic vapors (various multilevel electromagnetically induced transparency vapors) and negative refractive index materials, and suggests some possible ways to manipulate wave propagations inside the artificial electromagnetic materials based on quantum coherence and quantum vacuum effects. In Chapters 1 and 2, the author reviews the previous papers on quantum coherence as well as the relevant work such as electromagnetically induced transparency (EIT), atomic population trapping and their various applications. The basic concepts of quantum coherence (atomic phase coherence, quantum interferences within atomic energy levels) and quantum vacuum are introduced, and the theoretical formulations for treating wave propagations in quantum coherent media are presented. In Chapter 3, the author considers three topics on the manipulation of light propagations via quantum coherence and quantum interferences: i) the evolutional optical behaviors (turn-on dynamics) of a four-level N-configuration atomic system is studied and the tunable optical behavior that depends on the intensity ratio of the signal field to the control field is considered. Some typical photonic logic gates (e.g. NOT and NOR gates) are designed based on the tunable four-level optical responses of the N-configuration atomic system; ii) the destructive and constructive quantum interferences between two control transitions (driven by the control fields) in a tripod-type four-level system is suggested. The double-control quantum interferences can be utilized to realize some photonic devices such as the logic-gate devices, e.g., NOT, OR, NOR and EXNOR gates; iii) some new quantum coherent schemes (using EIT and dressed-state mixed-parity transitions) for realizing negative refractive indices are proposed. The most remarkable characteristic (and advantage) of the present scenarios is such that the isotropic left-handed media (with microscopic structure units at the atomic level) in the optical frequency band can be achieved. Quantum vacuum (the ground state of quantized fields) can exhibit many interesting effects. In Chapter 4, we investigate two quantum-vacuum effects in artificial materials: i) the anisotropic distribution of quantum-vacuum momentum density in a moving electromagnetic medium; ii) the angular momentum transfer between quantum vacuum and anisotropic medium. Such quantum-vacuum macroscopic mechanical effects could be detected by current technology, e.g., the so-called fiber optical sensor that can measure motion with nanoscale sensitivity. We expect that these vacuum effects could be utilized to develop sensitive sensor techniques or to design new quantum optical and photonic devices.In Chapter 5, the author suggests some interesting effects due to the combination of quantum coherence and quantum vacuum, i.e., the quantum coherent effects, in which the quantum-vacuum fluctuation field is involved. Two topics are addressed: i) spontaneous emission inhibition due to quantum interference in a three-level system; ii) quantum light-induced guiding potentials for coherent manipulation of atomic matter waves (containing multilevel atoms). These quantum guiding potentials could be utilized to cool and trap atoms, and may be used for the development of new techniques of atom fibers and atom chips, where the coherent manipulation of atomic matter waves is needed.In Chapter 6, we conclude this thesis with some remarks, briefly discuss new work that deserves further consideration in the future, and present a guide to the previously published papers by us. / QC 20100810

Decades of efforts have pushed the replacement of electrical interconnects by optical links to the interconnects between computers, racks and circuit boards. It may be expected that optical solutions will further be used for inter-chip and intra-chip interconnects with potential benefits in bandwidth, capacity, delay, power consumption and crosstalk. Silicon integration is emerging to be the best candidate nowadays due to not only the dominant status of silicon in microelectronics but also the great advantages brought to the photonic integrated circuits (PICs). Regarding the recent breakthroughs concerning active devices on silicon substrate, the question left is no longer the feasibility of the optical interconnects based on silicon but the competitiveness of the silicon device compared with other alternatives. This thesis focuses on the study of two key components for the optical interconnects, both especially designed and fabricated for silicon platform. One is a high speed electroabsorption modulator (EAM), realized by transferring an InP-based segmented design to the hybrid silicon evanescent platform. The purpose here is to increase the speed of the silicon PICs to over 50  Gb/s or more. The other one is a high performance grating coupler, with the purpose to improve the optical interface between the silicon PICs and the outside fiber-based communication system. An general approach based on the transmission line analysis has been developed to evaluate the modulation response of an EAM with a lumped, traveling-wave, segmented or capacitively-loaded configuration. A genetic algorithm is used to optimize its configuration. This method has been applied to the design of the EAMs on hybrid silicon evanescent platform. Based on the comparison of various electrode design, segmented configuration is adopted for the target of a bandwidth over 40 GHz with as low as possible voltage and high extinction ratio. In addition to the common periodic analysis, the grating coupler is analyzed by the antenna theory assisted with an improved volume-current method, where the directionality of a grating coupler can be obtained analytically. In order to improve the performance of the grating coupler, a direct way is to address its shortcoming by e.g. increasing the coupling efficiency. For this reason, a nonuniform grating coupler with apodized grooves has been developed with a coupling efficiency of 64%, nearly a double of a standard one. Another way is to add more functionalities to the grating coupler. To do this, a polarization beam splitter (PBS) based on a bidirectional grating coupler has been proposed and experimentally demonstrated. An extinction ratio of around -20 dB, as well as a maximum coupling efficiency of over 50% for both polarizations, is achieved by such a PBS with a Bragg reflector underneath. / QC 20100906

Advancements in photonic integrated circuits, so-called PICs, have progressed fast in the last decades. More complex PICs are getting developed, which are promising in possibly offering advantages like low power consumption and high-performance computing. Re-programmable photonic FPGAs are one of these candidates. To make these PICs viable, fundamental building blocks based on photonics need to be developed. Some of those fundamental building blocks are tunable silicon ring resonators, which can be used to filter signals in the transmission of light through photonic circuits. Fabrication of PICs is developing and those components are getting smaller, which leads to a strong sensitivity of their behavior to nanometer-scale variations. That has created a need for active tuning of those devices to recuperate those variances. One promising way to tune silicon ring resonator devices is to integrate microelectromechanical systems (MEMS) into the tuning section of the devices, because of their local and low power actuation. They are prospective to eliminate drawbacks from usual actuation methods like thermal actuation, which comes with high power consumption and cross talk while heating the functional sections of the ring. In this thesis, we have measured and analyzed MEMS-tunable silicon ring resonators, featuring two different designs, being an all-pass ring resonator and an add-drop ring resonator. The MEMS in the design are used to change the gap between the waveguides in their directional coupler and phase shifter section to control the position and extinction ratios of the ring resonance dips, which has been successfully demonstrated for the all-pass ring resonator. For the add-drop ring resonators, we have obtained performance parameters of their resonances with an average Q-factor of 3000 over the measured wavelength ranged from 1460nm to 1580nm and the characteristic behavior of their transmission has been shown without actuation. Further investigation with MEMS actuation of add-drop ring resonators and passive measurements on all-pass ring resonators can be done for a better understanding of their behavior and functionality. This can be achieved by characterizing all-pass ring resonators in terms of obtained performance parameters and by active measurements on add-drop ring resonators, as we expect that their MEMS could enable similar functionalities as all-pass ring resonators. Our first characterization results confirm the potential of MEMS for ring resonator tuning and could enable future circuits based on ring resonators with low power consumption. / Framsteg inom fotoniska integrerade kretsar, så kallade PIC, har utvecklats snabbt under de senaste decennierna. Mer komplexa PIC utvecklas, vilket lovar att möjligen erbjuda fördelar som låg strömförbrukning och högpresterande datorer. Omprogrammerbara fotoniska FPGA är en av dessa kandidater. För att göra dessa PICs livskraftiga måste grundläggande byggstenar baserade på fotonik utvecklas. Några av dessa grundläggande byggstenar är avstämningsbara kiselringresonatorer, som kan användas för att filtrera signaler vid överföring av ljus genom fotoniska kretsar. Tillverkning av PIC utvecklas och dessa komponenter blir mindre, vilket leder till en stark känslighet för variationer, även på nanometer skala. Det har skapat ett behov av aktiv inställning av dessa enheter för att återhämta dessa avvikelser. Ett lovande sätt att ställa in kiselringresonatoranordningar är att integrera mikroelektromekaniska system (MEMS) i enhetens stämningsdel på grund av deras lokala och lågeffektaktivering. De kan eliminera nackdelar med vanliga manövreringsmetoder som termisk aktivering, som kommer med hög strömförbrukning och termisk överhöring. I denna avhandling har vi mätt och analyserat MEMS-avstämbara kiselringresonatorer, med två olika designer, som är en all-pass ringres-onator och en add-drop ringresonator. MEMS i konstruktionen används för att ändra gapet mellan vågledarna i deras kopplare och fasskiftarsektion för att styra positionen och djupet på ringresonaserna, vilket har visats framgångsrikt för allpassningsresonatorn. För add-dropringresonatorer har vi erhållit prestandaparametrar för deras resonanser med en genomsnittlig Q-faktor på 3000 över den uppmätta våglängden som varierar från 1460 nm till 1580 nm och det karakteristiska beteendet för deras överföring har visats utan aktivering. Ytterligare undersökning med MEMS-aktivering av add-drop-ringresonatorer och passiva mätningar på all-pass-ringresonatorer kan göras för en bättre förståelse av deras beteende och funktionalitet. Detta kan uppnås genom att karakterisera allpassningsresonatorer i termer av erhållna prestandaparametrar och genom aktiva mätningar på add-drop-ringresonatorer, eftersom vi förväntar oss att deras MEMS kan möjliggöra liknande funktioner som all-pass-ringresonatorer. Våra första karakteriseringsresultat bekräftar MEMS potential för ringresonatorinställning och kan möjliggöra framtida kretsar baserade på ringresonatorer med låg strömförbrukning.