In dieser Arbeit wurden mit Hilfe einer Kombination aus „metal assisted chemical etching“ (MACE) und Polystyrol-Nanopartikel-Lithographie, Säulen-strukturierte Siliziumoberflächen mit verschiedenen Säulendurchmessern und –längen, wie auch unterschiedlichen Säulenabständen, synthetisiert. Das im Anschluss durchgeführte Elektropolier-Verfahren verhalf dabei, die durch den MACE-Prozess erhöhte Oberflächendefektdichte (DSS) zu reduzieren. Dieses Verfahren wurde von in situ Photolumineszenzmessungen unterstützt. Eine im Anschluss an das Elektropolierverfahren durchgeführte Methylpassivierung erwies sich als notwendig, um den Zustand der reduzierten DSS für einen längeren Zeitraum an Luft stabil zu halten. Die elektropolierten und methylpassivierten Oberflächen wurden als Substrate in Kombination mit dem leitfähigen Polymer PEDOT:PSS für die Herstellung von Hybridsolarzellen verwendet. Im Vergleich zu Zellen deren strukturierte Oberfläche nicht zuvor elektropoliert worden ist, kam es bei den zusätzlich elektropolierten Zellen zu einer Effizienzverbesserung und einer Erhöhung des Kurzschlussstroms (JSC). Elektrochemische Verfahren zur Veränderung der Säulen-Morphologie sind in dieser Arbeit ebenfalls untersucht worden. Um eine strukturierte Oberfläche auch in anderen Bereichen, wie etwa der Biosensorik, verwenden zu können, bedarf es neben der Methylpassivierung weiterer Formen der Funktionalisierung. Im Rahmen dieser Arbeit wurde ein Syntheseweg entwickelt, der es ermöglicht direkt an das Siliziumsubstrat gebundene Hydroxylgruppen zu erhalten, ohne dass es zu einer Bildung von intermediären Oxidschichten zwischen Substrat und den Hydroxylgruppen kommt. Diese wurden anschließend mit verschiedenen Silanen umgesetzt, um organische Gruppen an die Oberfläche zu binden. Die gebundenen Silanderivate können im Folgenden weiter modifiziert werden, um die selektive Anbindung von Biomolekülen zu ermöglichen. / Within this work, the “metal assisted chemical etching” (MACE) technique was combined with shadow nanosphere lithography to fabricate nanowire structured Si surfaces with different wire lengths and diameters. Electropolishing procedures subsequent to the wire growth resulted in a reduction of the surface defect density (DSS). The electropolishing procedure was directly monitored with the help of in situ photoluminescence spectroscopy. Previous works already observed a full and air stable surface passivation of flat Si surfaces by methylation. Also in the present work, the nanowire surfaces were methylated after the electropolishing procedure to preserve the reduced DSS. To determine the impact of this method on the solar cell performance, the electropolished and methylated surfaces were combined with the conductive polymer PEDOT:PSS. It revealed that the cells with the electropolished substrates exhibit a higher efficiency and an increased short circuit current (JSC). Different electrochemical procedures to change the wire morphology after the structuring have been investigated as well. To use the Si substrates for applications such as biosensing, different passivation/functionalization techniques besides the methylation are required. In this thesis, a new functionalization procedure was developed to obtain air stable hydroxyl groups that are directly bound to the Si substrate without an intervening oxide layer. To demonstrate the possibility to use these hydroxyl groups in the same way as the hydroxyl groups present on a Si oxide layer, further modifications with different silane species, such as APTES and AMMS, were conducted. In order to generate a more selective anchor group, the bound APTES molecules were further modified by a maleimide derivative, which allow for the selective binding of thiol-containing molecules.

This thesis presents an investigation into the factors affecting the morphology of hybrid inorganic/organic photoactive layers used in photovoltaic cells. Although optimisation of the organic (polymer) phase has received substantial attention, research into the morphology of the inorganic phase (semiconducting nanocrystals) remains limited. It is believed that there is a strong link between the morphology of the final photoactive film and the quality of the initial nanocrystal dispersion. To this end, two nanocrystal systems were investigated; zinc oxide (ZnO) and lead sulphide (PbS). ZnO nanocrystals were synthesised and found to possess reproducible characteristics. It was determined that colloid stability was initially dependent upon the presence of acetate groups bound to the surface, which in turn required a small quantity of methanol to be present in the organic dispersant. It was also discovered that while methanol evaporated readily from the surface of the nanocrystals, another molecule, 1-propylamine (1-PA), did not. Further investigations showed that while methanol only weakly physisorbed to the surface of ZnO nanocrystals, 1-PA formed strong, dative covalent bonds with Zn2+, preventing evaporation despite a low boiling point. Subsequent investigations into the effects of different ligands upon colloid stability found that amine-based groups typically possessed superior stabilising capabilities compared to alcohol-based analogues. The characteristics of nanocrystal / polymer blends were also investigated. It was determined that the nanocrystal dispersion became unstable at higher concentrations of polymer due to depletion aggregation. Films of nanocrystal / polymer blends were cast from dispersions containing either alcohol or amine-based ligands, and it was observed that dispersions stabilised with 1-PA possessed smooth morphologies on the micrometer scale. Investigations at the nanometer scale, however, revealed aggregates large enough to favour recombination.The latter half of this thesis regards the characterisation of PbS nanocrystals and investigations into triggered aggregation. It was determined that while PbS nanocrystals possessed reproducible characteristics, the stabilising molecule, oleic acid (OA) was insulating. The effects of exchanging the OA groups for a shorter ligand, butylamine (BA) were investigated.Finally, PbS nanocrystals were treated with a bidentate ligand, 1,2-ethanedithiol (EDT) to induce triggered aggregation. It was observed that the system was highly sensitive to the concentration of EDT in dispersion, forming small, relatively dispersed aggregates at low [EDT], and micrometer-sized crystalline structures at high [EDT]. The characterisation and entrapment of these nanocrystal structures within semi-conducting polymer films is also discussed.

Traditional sources of electrical energy are finite and can produce significant pollution. Solar cells produce clean energy from incident sunlight, and will be an important part of our energy future. A new nanostructured extremely thin absorber solar cell with 0.98% power conversion efficiency and maximum external quantum efficiency of 61% at 650 nm has been fabricated and characterized. This solar cell is composed of a fluorine-doped tin oxide base layer, n-type aluminum doped zinc oxide nanowires, a cadmium selenide absorber layer, poly(3-hexylthiophene) as a p-type layer, and thermally evaporated gold as a back contact. Zinc oxide nanowire electrodeposition has been investigated for different electrical environments, and the role of a zinc oxide thin film layer has been established. Cadmium selenide nanoparticles have been produced and optimized in-house and compared to commercially produced nanoparticles. Argon plasma cleaning has been investigated as a method to improve electronic behavior at cadmium selenide interfaces. The thermal anneal process for cadmium selenide nanoparticles has been studied, and a laser anneal process has been investigated. It has been found that the most efficient solar cells in this study are produced with a zinc oxide thin film, zinc oxide nanowires grown under constant -1V bias between the substrate material and the anode, cadmium selenide nanoparticles purchased commercially and annealed for 24 hours in the presence of cadmium chloride, and high molecular weight poly(3-hexylthiophene) spin-coated in a nitrogen environment.

Le travail présenté dans ce mémoire porte sur la réalisation et l’étude des cellules solaires PV hybrides à réseaux interpénétrés utilisant les nanofils de silicium. Nos études ont porté essentiellement sur l’optimisation des structures hybrides à base de PVK ou de MEH-PPV mélangé dans leur volume avec une phase de nanofils de silicium, référant aux structures PVK/NFSi et MEH-PPV/NFSi respectivement. Cette étude a montré l’étroite interdépendance entre la morphologie des nanocomposites et les propriétés photovoltaïques des cellules réalisées. Nous avons étudiés l’influence de la concentration des nanofils de silicium sur le processus de dissociation des paires photo-générées. Nous avons également étudié l’effet des traitements thermiques et nous avons mis en évidence un meilleur transfert de charge dans le cas des structures PVK/NFSi. Nous avons aussi observé l’influence bénéfique de la désoxydation ainsi que le traitement de fonctionnalisation des nanofils sur l’amélioration du transfert de charge dans le cas des structures réalisées. En conclusion, nous avons montré que les cellules PV hybrides à réseaux interpénétrés utilisant les nanofils de silicium peuvent être optimisées grâce à la compréhension et au réglage fin du transfert de charges / The work presented in this thesis focuses on the implementation and study of hybrid solar cells interpenetrating networks using silicon nanowires. Our studies have focused on the optimization of hybrid structures based PVK or MEH-PPV mixed in their volume with silicon nanowires phase, referring to structures PVK/NFSI and MEH-PPV/NFSI respectively. This study showed the close interdependence between morphology and properties of nanocomposites photovoltaic cells made. We studied the influence of the concentration of silicon nanowires on the dissociation process of photo-generated pairs. We also studied the effect of heat treatment and we have demonstrated a better load transfer in the case of structures PVK/NFSI. We also observed the beneficial effect of deoxidation treatment and functionalization of the nanowires on the improvement of charge transfer in the case of structures made. In conclusion, we have shown that the PV hybrid cell using silicon nanowires can be optimized through understanding and fine tuning of the charge transfer

Das Hauptaugenmerk dieser Arbeit liegt auf der Entwicklung einer Hybridsolarzelle, in der der anorganische Halbleiter Silizium, das organische Polymer und das Kontaktsystem so aufeinander abgestimmt sind, dass ihre Kombination zu einem Bauelement mit hohem Wirkungsgrad führt. Um dieses Ziel zu erreichen wurden verschiedene Maßnahmen ergriffen. Neue Polymermaterialien, abgeleitet von dem prototypischen organischen Halbleiter poly(3-hexylthiophen 2,5 diyl) (P3HT), namentlich poly(3-[3,6-dioxaheptyl]-thiophen) (P3DOT) und poly(3-[2,5,8-trioxanonyl]-thiophen) (P3TOT), wurden umfassend hinsichtlich ihrer Struktur untersucht. Poly thiophen/c-Si hybride Solarzellen, hergestellt aus diesen neuen Polymeren, erreichten Effizienzen bis zu 11 %. Die vollständigen Banddiagramme dieser Poly thiophen/c-Si Hybridgrenzflächen wurden mittels Photoelektronenspektroskopie aufgenommen. Außerdem wurde der Einfluss des Kontaktsystems auf die darunter liegenden Schichten mittels Oberflächenspannungsspektroskopie untersucht. Das Resultat dieser Messungen weißt eine Inversionslage unter der Siliziumoberfläche nach, die sich aufgrund des verwendeten semitransparenten Metallkontaktes formt. Dadurch lassen sich diese Bauteile als MIS Inversionsschicht Solarzelle kategorisieren. Um die Hybridsolarzellen weiter zu verbessern, wurde versucht den semitransparenten Metallkontakt durch Graphen zu ersetzen. Das Graphen wurde durch einen CVD-Prozess gewachsen und erreichte eine laterale Ausdehnung von bis zu 1 cm2. Der Übertrag auf die Solarzelle erfolgte mittels eines Wasser und Zerstörungsfreiem Transferprozess. Trotz dem erfolgreichen Aufbringen des Graphen limitierte ein geringer Füllfaktor aufgrund der geringen Ladungsträgerdichte im Graphen den Wirkungsgrad der Solarzelle. In einem letzten Schritt wurde das Polymer P3HT zum ersten Mal mit polykristallinen Siliziumabsorbern kombiniert. Die invertierte Zellstruktur, die hierbei zu Anwendung kam, erhöhte die Lebensdauer der Solarzelle erheblich. / The scope of this thesis was the development of a hybrid solar cell based on silicon in which the inorganic semiconductor, the organic polymer and the contact system are combined in such a manner to result in a photovoltaic device with high power conversion efficiency. To reach this goal several measures were taken. New polymer materials derived from the prototypical organic semiconductor poly(3-hexylthiophene 2,5 diyl) (P3HT), namely poly(3-[3,6-dioxaheptyl]-thiophene) (P3DOT) and poly(3-[2,5,8-trioxanonyl]-thiophene) (P3TOT), were extensively characterized regarding its structural properties. Poly thiophene/c-Si hybrid solar cells fabricated from these new polymers exhibited power conversion efficiencies up to 11 %. The energy level alignment of these poly thiophene/c Si hybrid interfaces was studied using photoelectron spectroscopy. Furthermore, the influence of the contact system on the underlying wafer is investigated with surface photovoltage measurements. The measurements revealed the formation of an inversion layer beneath the silicon surface due to the semitransparent metal contact used in the devices. Therefore, these devices can be classified as MIS inversion layer solar cells. To further improve the hybrid poly thiophene/c-Si solar cells by substituting the semitransparent metal contact, graphene was implemented in the device design as a transparent front contact. The CVD grown graphene sheet had a lateral size of up to 1 cm2 and was applied onto the solar cell using a non-destructive and water-free transfer process. However, despite the successful transfer the power conversion efficiency was restricted by the low fill factor due to a low charge carrier density in the graphene. As a last step, hybrid solar cells in the combination P3HT/polycrystalline silicon absorbers on glass were fabricated for the first time. The inverted device structure used for these solar cells proved beneficial for the lifetime. These devices were stable for up to 3 months.

This work is part of the inter-laboratory collaboration to study the stability of seven distinct sets of state-of-the-art organic photovoltaic (OPV) devices prepared by leading research laboratories. All devices have been shipped to and degraded at RISØ-DTU up to 1830 hours in accordance with established ISOS-3 protocols under defined illumination conditions. In this work, we apply the Incident Photon-to-Electron Conversion Efficiency (IPCE) and the in situ IPCE techniques to determine the relation between solar cell performance and solar cell stability. Different ageing conditions were considered: accelerated full sun simulation, low level indoor fluorescent lighting and dark storage. The devices were also monitored under conditions of ambient and inert (N2) atmospheres, which allows for the identification of the solar cell materials more susceptible to degradation by ambient air (oxygen and moisture). The different OPVs configurations permitted the study of the intrinsic stability of the devices depending on: two different ITO-replacement alternatives, two different hole extraction layers (PEDOT:PSS and MoO3), and two different P3HT-based polymers. The response of un-encapsulated devices to ambient atmosphere offered insight into the importance of moisture in solar cell performance. Our results demonstrate that the IPCE and the in situ IPCE techniques are valuable analytical methods to understand device degradation and solar cell lifetime. / Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG-geförderten) Allianz- bzw. Nationallizenz frei zugänglich.

Les cellules solaires nanostructurées ont été développées pour réduire le coût du photovoltaïque et le rendre compétitif aux autres sources d’énergies. Dans ce but deux cellules solaires ont été étudié durant la thèse: la cellule « eta » (Extremely Thin Absorber) et la cellule hybride à polymères. Dans un premier temps, des couches 2D et nanofils de ZnO ont été réalisés par voie électrochimique sur des substrats verre/TCO (oxyde transparent et conducteur). Il est montré que la température du bain, la densité de charge et la concentration de l’électrolyte support (KCl) infleuncent la morphologie, composition, cristallisation et propriétés optiques des couches. Les films déposés à 0,1 M KCl et à T ≥ 50°C, présente de bonnes propriétés physico-chimiques. La couche 2D est ensuite utilisée pour la croissance des nanofils de ZnO et leurs dimensions sont ajustées avec la moprhologie et l’épaisseur de cette couche. L’électrolyte support et la densité de charge permettent également de contrôler les dimensions des nanofils. Dans un deuxième temps, les nanofils de ZnO ont été photo-sensibilisés par deux types d’absorbeurs : CuInS2 (CIS) et Cu2ZnSnS4 (CZTS). Ils ont été réalisés par différentes méthodes : SILAR (Successive Ion Layer Adsorption and Reaction), électrodépôt et dépôt de nanoparticules pré-synthétisées (pour CIS). Les films préparés par voie SILAR sont très uniformes autour des nanofils. Tandis que ceux réalisés par électrodépôt sont moins homogènes mais de très bonnes qualités cristallines. Grâce à la fonctionnalisation des nanofils, une couche de nanoparticules de CuInS2 très uniforme est déposée. Les cellules « eta » réalisées avec ces structures cœur/coquille montrent un effet photovoltaïque. Les films de ZnO électrodéposés ont été intégrés dans des cellules solaires hybrides à polymères sur substrats verres et plastiques. Ces cellules ont montré de bons rendements et une haute stabilité. / Nanostructured solar cells have been proposed as a solution for photovoltaic cost reduction and to rival the cost of grid-powered electricity. Regarding this challenge, two kinds of solar cells have been studied within the PhD thesis: the Extremely Thin Absorber Solar cells (eta) and the polymer hybrid solar cell. First, we are reporting on the electrochemical deposition of ZnO 2D layers and nanowires on glass substrates covered with TCO (Transparent Conducting Oxide). It is shown that the bath temperature and the supporting electrolyte concentration (KCl) play an important role on the ZnO layer morphology, composition, crystallization and optical properties. The film deposited from 0.1 M KCl and T ≥ 50°C exhibit very good optical and structural properties. These 2D layers are used for consequent ZnO nanowires electrodeposition and their dimensions could be tailored by the seed layer morphology and thickness. The supporting electrolyte concentration and the passed charge density could be additionally used to control their dimensions. Then, the ZnO nanowires have been photosensitized with two absorbers: CuInS2 (CIS) and Cu2ZnSnS4 (CZTS). These materials are prepared by: Successive Ion Layer Adsorption and Reaction (SILAR), electrodeposition and nanoparticules deposition (for CIS). The SILAR films are very uniform around the nanowires. The layers prepared by electrodeposition are less uniform but exhibit very good structural properties. Uniform thin film of CuInS2 nanoparticules are deposited onto functionalized ZnO nanowires. The eta solar cells fabricated with these core/shell nanostructures have shown a photovoltaic effect. The ZnO thin films have been integrated in hybrid solar cells on flexible and rigid substrates. These cells show good power conversion efficiency and a high stability.

This thesis outlines investigations of metal oxide/organic interfaces in photo-voltaic devices. It focuses on device instabilities originating from the metal oxide layer surface sensitivity and it presents suggested mechanisms behind these in- stabilities. A simple sol-gel solution deposition technique for the fabrication of stable and highly performing transparent conducting mixed metal oxides (ZnMO) is presented. It is demonstrated that the use of amorphous, mixed metal oxides allows improving the performance and stability of interfacial charge extraction layers for organic solar cells. Two novel ternary metal oxides, zinc-strontrium- oxide (ZnSrO) and zinc-barium-oxide (ZnBaO), were fabricated and their use as electron extraction layers in inverted organic photovoltaics is investigated. We show that using these ternary oxides can lead to superior devices by: prevent- ing a dipole forming between the oxide and the active organic layer in a model ZnMO/P3HT:PCBM OPV as well as lead to improved surface coverage by a self assembled monolayer and promote a significantly improved charge separation efficiency in a ZnMO/P3HT hybrid device. Additionally a spectroscopic technique allowing a versatility of characterisa- tion for long-term stability investigations of organic solar cells is reported. A device instability under broadband light exposure in vacuum conditions for an inverted ZnSrO/PTB7:PC71BM OPV is observed. Direct spectroscopic evidence and electrical characterisation indicate the formation of the PC71BM radical an- ion associated with a loss in device performance. A charge transfer mechanism between a heavily doped oxide layer and the organic layers is suggested and dis- cussed.

This work is part of the inter-laboratory collaboration to study the stability of seven distinct sets of state-of-the-art organic photovoltaic (OPV) devices prepared by leading research laboratories. All devices have been shipped to and degraded at RISØ-DTU up to 1830 hours in accordance with established ISOS-3 protocols under defined illumination conditions. In this work, we apply the Incident Photon-to-Electron Conversion Efficiency (IPCE) and the in situ IPCE techniques to determine the relation between solar cell performance and solar cell stability. Different ageing conditions were considered: accelerated full sun simulation, low level indoor fluorescent lighting and dark storage. The devices were also monitored under conditions of ambient and inert (N2) atmospheres, which allows for the identification of the solar cell materials more susceptible to degradation by ambient air (oxygen and moisture). The different OPVs configurations permitted the study of the intrinsic stability of the devices depending on: two different ITO-replacement alternatives, two different hole extraction layers (PEDOT:PSS and MoO3), and two different P3HT-based polymers. The response of un-encapsulated devices to ambient atmosphere offered insight into the importance of moisture in solar cell performance. Our results demonstrate that the IPCE and the in situ IPCE techniques are valuable analytical methods to understand device degradation and solar cell lifetime. / Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG-geförderten) Allianz- bzw. Nationallizenz frei zugänglich.