<p>Thin films play an important role in science and technology today. By combining different materials, properties for specific applications can be optimised. In this thesis growth of copper, copper(I) oxide and copper(I) nitride on two different substrates, amorphous SiO₂ and single crystalline α-Al₂O₃ by the so called Atomic Layer Deposition (ALD) techniques has been studied. This technique allows precise control of the growth process at monolayer level on solid substrates. Other characteristic features of ALD are that it produces films with excellent step coverage and good uniformity even as extremely thin films on complicated shaped substrates.</p><p>Alternative deposition schemes were developed for the materials of interest. It was demonstrated that use of intermediate water pulses affected the deposition pathways considerably. By adding water, the films are thought to grow via formation of an oxide over-layer instead of through a direct reaction between the precursors as in the case without water.</p><p>For growth of copper(I) nitride from Cu(hfac)₂ and ammonia no film growth occurred without adding water to the growth process. The Cu₃N films could be transformed into conducting copper films by post annealing. In copper growth from CuCl and H₂ the water affected film growth on the alumina substrates considerably more than on the fused silica substrates. The existence of surface -OH and/or -NH_x groups was often found to play an important role, according to both theoretical calculations and experimental results.</p>

<p>Materials with new or improved properties are crucial for technological development. To provide the foundation for future successful products, it is important to prepare and characterise new chemical compounds that could show unusual properties. The properties of magnetic materials are closely related to their crystal, magnetic and electronic structures. This thesis focuses on the novel synthesis and structural characterisation of a number of new ternary or <i>pseudo</i>-ternary silicides and germanides of manganese with iridium, cobalt or palladium. To provide a more complete picture of the complex magnetic properties, crystal and magnetic structure refinements by the Rietveld method of X-ray and neutron powder diffraction data are complemented by single-crystal X-ray diffraction, electron diffraction, magnetisation measurements and Reverse Monte Carlo simulations of magnetic short-range order. The experimental results are corroborated by first-principles electronic structure and total energy calculations. </p><p>A commensurate non-collinear antiferromagnetic structure is found for most compounds of the solid solution Mn₃Ir_1-yCo_ySi_1-xGe_x. The non-collinearity is a result of geometric frustration in a crystal structure with magnetic Mn atoms located on a three-dimensional network of triangles. The close structural similarity to the β-modification of elemental manganese, which does not order magnetically, inspired a closer theoretical comparison of the Mn₃Ir_1-yCo_ySi_1-xGe_x propertieswith β-Mn.</p><p>Magnetic frustration is also observed for Mn₄Ir_7-xMn_xGe₆, and is an important factor underlying the dramatic change from commensurate antiferromagnetic order to spin glass properties induced by a small variation in Mn concentration. Magnetic short-range order with dominant antiferromagnetic correlation is observed for Mn₈Pd₁₅Si₇, and results from a random distribution of Mn atoms in-between the geometrically frustrated magnetic moments on the Mn octahedra. </p><p>An incommensurate cycloidal magnetic structure, observed for IrMnSi, is stabilised by an electronic structure effect, which also accounts for the non-collinearity of the Mn₃IrSi type magnetic structure.</p>

Diabetes mellitus is one of the most threatening epidemics of modern times with rapidly increasing incidence. Vanadium and peroxovanadium compounds have been shown to exert insulin–like actions and, in contrast to insulin, are orally applicable. However, problems with side–effects and toxicity remain. The exact mechanism(s) by which these compounds act are not yet fully known. Thus, a better understanding of the aqueous chemistry of vanadates and peroxovanadates in the presence of various (bio)ligands is needed. The present thesis summarises six papers dealing mainly with aqueous speciation in different vanadate – and peroxovanadate – ligand systems of biological and medical relevance. Altogether, five ligands have been studied, including important blood constituents (lactate, citrate and phosphate), a potential drug candidate (picolinic acid), and a dipeptide (alanyl serine) to model the interaction of (peroxo)vanadate in the active site of enzymes. Since all five ligands have been studied both with vanadates and peroxovanadates, the number of systems described in the present work is eleven, including the vanadate – citrate – lactate mixed ligand system. The pH–independent formation constants have been determined for 33 ternary vanadate – ligand, 41 quaternary peroxovanadate – ligand and two vanadate – mixed ligand species in addition to the pKa values of all five ligands. These constants have been used to model physiological conditions, and the biomedical relevance of the different species is discussed. The studies have been performed at 25 ºC in the physiological medium of 0.150 M Na(Cl), i.e. the ionic strength of human blood. No buffers have been used, and wide pH–ranges have usually been covered. The applied experimental techniques comprise mostly 51V NMR and potentiometry, but 31P, 13C, 1H and 14N NMR as well as EPR and ESI–MS have also been used to gain additional information. Multimethod data have been treated by the least–squares program LAKE and modelling has been carried out by the software package WinSGW. Whenever possible, solution structures of the species have been proposed. In addition, simple biological tests have been carried out to determine the stability of the formed peroxovanadate complexes in the presence of human catalase. A brief comparison is given of the different vanadate – ligand and peroxovanadate – ligand systems with emphasis on observed trends and general features.

Thin films play an important role in science and technology today. By combining different materials, properties for specific applications can be optimised. In this thesis growth of copper, copper(I) oxide and copper(I) nitride on two different substrates, amorphous SiO2 and single crystalline α-Al2O3 by the so called Atomic Layer Deposition (ALD) techniques has been studied. This technique allows precise control of the growth process at monolayer level on solid substrates. Other characteristic features of ALD are that it produces films with excellent step coverage and good uniformity even as extremely thin films on complicated shaped substrates. Alternative deposition schemes were developed for the materials of interest. It was demonstrated that use of intermediate water pulses affected the deposition pathways considerably. By adding water, the films are thought to grow via formation of an oxide over-layer instead of through a direct reaction between the precursors as in the case without water. For growth of copper(I) nitride from Cu(hfac)2 and ammonia no film growth occurred without adding water to the growth process. The Cu3N films could be transformed into conducting copper films by post annealing. In copper growth from CuCl and H2 the water affected film growth on the alumina substrates considerably more than on the fused silica substrates. The existence of surface -OH and/or -NHx groups was often found to play an important role, according to both theoretical calculations and experimental results.

The chemistry of mineral surfaces is of great importance in many different areas including natural processes occurring in oceans, rivers, lakes and soils. Manganese (hydr)oxides are one important group to these natural processes, and the thermodynamically most stable trivalent manganese (hydr)oxide, manganit (γ-MnOOH), is studied in this thesis. This thesis summarises six papers in which the surface chemistry of synthetic manganite has been investigated with respect to surface acid-base properties, dissolution, and adsorption of Cd(II) and the herbicide N-(phosphonomethyl)glycine (glyphosate, PMG). In these papers, a wide range of analysis techniques were used, including X-ray photoelectron spectroscopy (XPS), extended X-ray absorption fine structure (EXAFS) spectroscopy, Fourier transform infra-red (FTIR) spectroscopy, atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray diffraction (XRD), potentiometry, electrophoretic mobility measurements and wet chemical techniques, in order to obtain a more complete understanding of the different processes occurring at the manganite-water interface. From the combined use of these techniques, a 1-pKa acid-base model was established that is valid at pH&gt;6. The model includes a Na+ interaction with the surface: =MnOH2+½ --&gt; =MnOH-½ + H+ log β0 (intr.) = -8.20 = -pHiep =MnOH2+½ + Na+ --&gt; =MnOHNa+½ + H+ log β0 (intr.) = -9.64 At pH&lt;6 the manganite crystals dissolve and disproportionate into pyrolusite (β-MnO2) and Mn(II)-ions in solution according to: 2 γ-MnOOH + 2H+ --&gt; β-MnO2 + Mn2+ + 2H2O log K0 = 7.61 ± 0.10 The adsorption and co-adsorption of Cd(II) and glyphosate at the manganite surface was studied at pH&gt;6. Cd(II) adsorption displays an adsorption edge at pH~8.5. Glyphosate adsorbs over the entire pH range, but the adsorption decreases with increasing pH. When the two substances are co-adsorbed, the adsorption of Cd(II) is increased at low pH but decreased at high pH. The adsorption of glyphosate is increased in the entire pH range in the presence of Cd(II). From XPS, FTIR and EXAFS it was found that glyphosate and Cd(II) form inner sphere complexes. The binary Cd(II)-surface complex is bonded by edge sharing of Mn and Cd octahedra on the (010) plane of manganite. Glyphosate forms inner-sphere complexes through an interaction between the phosphonate group and the manganite surface. The largest fraction of this binary glyphosate complex is protonated throughout the pH range. A ternary surface complex is also present, and its structure is explained as type B ternary surface complex (surface-glyphosate-Cd(II)). The chelating rings between the Cd(II) and glyphosate, found in aqueous complexes, are maintained at the surface, and the ternary complex is bound to the surface through the phosphonate group of the ligand.

Materials with new or improved properties are crucial for technological development. To provide the foundation for future successful products, it is important to prepare and characterise new chemical compounds that could show unusual properties. The properties of magnetic materials are closely related to their crystal, magnetic and electronic structures. This thesis focuses on the novel synthesis and structural characterisation of a number of new ternary or pseudo-ternary silicides and germanides of manganese with iridium, cobalt or palladium. To provide a more complete picture of the complex magnetic properties, crystal and magnetic structure refinements by the Rietveld method of X-ray and neutron powder diffraction data are complemented by single-crystal X-ray diffraction, electron diffraction, magnetisation measurements and Reverse Monte Carlo simulations of magnetic short-range order. The experimental results are corroborated by first-principles electronic structure and total energy calculations. A commensurate non-collinear antiferromagnetic structure is found for most compounds of the solid solution Mn3Ir1-yCoySi1-xGex. The non-collinearity is a result of geometric frustration in a crystal structure with magnetic Mn atoms located on a three-dimensional network of triangles. The close structural similarity to the β-modification of elemental manganese, which does not order magnetically, inspired a closer theoretical comparison of the Mn3Ir1-yCoySi1-xGex propertieswith β-Mn. Magnetic frustration is also observed for Mn4Ir7-xMnxGe6, and is an important factor underlying the dramatic change from commensurate antiferromagnetic order to spin glass properties induced by a small variation in Mn concentration. Magnetic short-range order with dominant antiferromagnetic correlation is observed for Mn8Pd15Si7, and results from a random distribution of Mn atoms in-between the geometrically frustrated magnetic moments on the Mn octahedra. An incommensurate cycloidal magnetic structure, observed for IrMnSi, is stabilised by an electronic structure effect, which also accounts for the non-collinearity of the Mn3IrSi type magnetic structure.

Research on inherently nanolaminated transition metal carbides is inspired by their unique properties combining metals and ceramics, such as higher damage tolerance, better machinability and lower brittleness compared to the binary counterparts, yet retaining the metallic conductivity. The interesting properties are related to their laminated structure, composed of transition-metalcarbide layers interleaved by non-transition-metal (carbide) layers. These materials in thin-film form are particularly interesting for potential applications such as protective coatings and electrical contacts. The goal of this work is to explore nanolaminated transition metal carbides from the aspects of phase formation and crystal growth during thin-film synthesis. This was realized by studying phases in select material systems synthesized from two major approaches, namely, fromdirect-deposition and post-deposition treatment. The first approach was used in studies on the Mo-Ga-C and Zr-Al-C systems. In the former system, intriguing properties have been predicted for the 3D phases and their 2D derivatives (socalled MXenes), while in the latter system, the phases are interesting for nuclear applications. In this work, the discovery of a new Mo-based nanolaminated ternary carbide, Mo2Ga2C, is evidenced from thin-film and bulk processes. Its structure was determined using theoretical and experimental techniques, showing that Mo2Ga2C has Ga double-layers in simple hexagonal stacking between adjacent Mo2C layers, and therefore is structurally very similar to Mo2GaC, except for the additional Ga layers. For the Zr-Al-C system, the optimization of phase composition and structure of Zr2Al3C4 in a thin-film deposition process was studied by evaluating the effect of deposition parameters. I concluded that the formation of Zr2Al3C4 is favored with a plasma flux overstoichiometric in Al, and with a minimum lattice-mismatch to the substrates. Consequently, epitaxial Zr2Al3C4 thin film of high quality were deposited on 4H-SiC(001) substrates at 800 °C. With the approach of post-deposition treatment, the studies were focused on a new method of thermally-induced selective substitution reaction of Au for the non-transition-metal layers in nanolaminated carbides. Here, the reaction mechanism has been explored in Al-containing (Ti2AlC and Ti3AlC2) and Ga-containing (Mo2GaC and Mo2Ga2C) phases. The Al and Ga in these phases were selectively replaced by Au while the carbide layers remained intact, resulting in the formation of new layered phases, Ti2Au2C, Ti3Au2C2, Mo2AuC, and Mo2(Au1-xGax)2C, respectively. The substitution reaction was explained by fast outward diffusion of the Al or Ga being attracted to the surface Au, in combination with back-filling of Au, which is chemically inert to the carbide layers,to the vacancies. The substitution reaction was further applied to Ga-containing nanolaminated carbides, (Cr0.5Mn0.5)2GaC and Mo2GaC, motivated by development of novel magnetic nanolaminates. The former experiment resulted in the formation of (Cr0.5Mn0.5)2AuC, where the retained (Cr0.5Mn0.5)2C layers allowed a comparative study on the magnetic properties under the exchange of Ga for Au. After Au substitution, reduction in the Curie temperature and the saturation magnetization were observed, showing a weakened magnetic exchange interaction of the magnetic (Cr0.5Mn0.5)2 Clayers across the Au. In the Mo2GaC case, an Fe-containing MAX phase, Mo2AC with 50 at.% of Fe on the A site, was synthesized through selective substitution of Au-Fe alloy for the Ga layers, showing the first direct evidence for Fe in the MAX-phase structure. The substitution of Fe did not take place on another Mo2GaC sample tested for Fe exchange only, indicating the essential role of Au in catalyzing the Fe-substitution reaction. The knowledge gained from this thesis work contributes to improved approaches for attaining thin films of nanolaminated transition metal carbides with desired phase composition and crystal quality. The reports on the new nanolaminated phases through exchange interactions are likely to expand the family of nanolaminated carbides and advance their properties, and trigger more studies on related (quasi-) 2D materials.

Biomimetic catalysis is an important research field, as a better understanding of nature´s powerful toolbox for the conversion of molecules can lead to technological progress. [FeFe]-hydrogenases are very efficient catalysts for hydrogen production. These enzymes play a crucial role in the metabolism of green algae and certain cyanobacteria. Their active site consists of a diiron complex that is embedded in an interactive protein matrix. In this thesis, two pathways for mimicking the outer coordination sphere effects resulting from the protein matrix are explored. The first is the construction of model complexes containing phosphine ligands that are coordinated to the iron center as well as covalently linked to the bridging ligand of the complex. The effect of such linkers is an increased energy barrier for the rotation of the Fe(CO2)(PL3)-subunit, which potentially could stabilize a terminal hydride that is an important intermediate in the proton reduction cycle. The second pathway follows the incorporation of [FeFe]-hydrogenase active site model complexes into metal-organic frameworks (MOFs). Resulting MOF-catalysts exhibit increased photocatalytic activity compared to homogenous references due to a stabilizing effect on catalytic intermediates by the surrounding framework. Catalyst accessibility within the MOF and the influence of the framework on chemical reactivity are examined in the work presented. Furthermore, an initial step towards application of MOF-catalysts in a device was made by interfacing them with electrodes. The work of this thesis highlights strategies for the improvement of biomimetic model catalysts and the knowledge gained can be transferred to other systems mimicking the function of enzymes.

The demand for alternative secondary batteries to lithium-ion batteries (LIBs) grows. Sodium-ion batteries (SIBs) have been studied for many years and could replace LIBsfor some application. Metallic anodes for both LIBs and SIBs are interesting due totheir high energy densities. Several aspects such as reactivity, stability and depositionmorphology must be properly addressed before metallic Na could be considered apossible anode material. This study aims to evaluate deposition of Na on Alelectrodes using fundamental electrochemical theories. Na deposition was studiedusing pouch cells and sodium triflate (NaOTf) in dimethyl glycol ether (diglyme) aselectrolyte. Galvanostatic deposition using different current densities, electrolyteconcentrations and potential pulses prior to galvanostatic deposition were tested. Theelectrochemical methods used in this study were galvanostatic deposition andchronoamperometry. The morphology of deposited Na was analyzed with ex-situscanning electron microscopy (SEM). A decrease of the size of deposited Na islandswas observed for both increasing current density and decreasing electrolyteconcentration. Fluctuations and poor stability in the deposition potential wereobtained when decreasing the electrolyte concentration under 0.5 M and also whenincreasing the current density over 1 mA cm-2. The most homogeneous depositionwas obtained with a 1030 ms potential pulse amplitude (-3 V vs. Na+/Na) prior togalvanostatic deposition (1 mA cm-2, 0.5 mAh cm-2) using 0.1 M NaOTf in diglyme aselectrolyte. Reproducibility was a major issue in this study and further investigation ofseveral parameters is needed.

<p>Li-ion batteries are not only a technology for the future, they are indeed already the technology of choice for today’s mobile phones, laptops and cordless power tools. Their ability to provide high energy densities inexpensively and in a way which conforms to modern environmental standards is constantly opening up new markets for these batteries. To be able to maintain this trend, it is imperative that all issues which relate safety to performance be studied in the greatest detail. The surface chemistry of the electrode-electrolyte interfaces is intrinsically crucial to Li-ion battery performance and safety. Unfortunately, the reactions occurring at these interfaces are still poorly understood. The aim of this thesis is therefore to increase our understanding of the surface chemistries and stability phenomena at the electrode-electrolyte interfaces for three novel Li-ion battery electrode materials.</p><p>Photoelectron spectroscopy has been used to study the surface chemistry of the anode material AlSb and the cathode materials LiFePO₄ and Li₂FeSiO₄. The cathode materials were both carbon-coated to improve inter-particle contact. The surface chemistry of these electrodes has been investigated in relation to their electrochemical performance and X-ray diffraction obtained structural results. Surface film formation and degradation reactions are also discussed.</p><p>For AlSb, it has been shown that most of the surface layer deposition occurs between 0.50 and 0.01 V <i>vs.</i> Li°/Li⁺ and that cycling performance improves when the lower cut-off potential of 0.50 V is used instead of 0.01 V. For both LiFePO₄ and Li₂FeSiO₄, the surface layer has been found to be very thin and does not provide complete surface coverage. Li₂CO₃ was also found on the surface of Li₂FeSiO₄ on exposure to air; this was found to disappear from the surface in a PC-based electrolyte. These results combine to give the promise of good long-term cycling with increased performance and safety for all three electrode materials studied.</p>