Yes / Passive prosthetic devices are set up to provide optimal function at customary walking speed and thus may function less effectively at other speeds. This partly explains why joint kinetic adaptations become more apparent in lower-limb amputees when walking at speeds other than customary. The present study determined whether a trans-tibial prosthesis incorporating a dynamic-response foot that was attached to the shank via an articulating hydraulic device (hyA-F) lessened speed-related adaptations in joint kinetics compared to when the foot was attached via a rigid, non-articulating attachment (rigF). Eight active unilateral trans-tibial amputees completed walking trials at their customary walking speed, and at speeds they deemed to be slow-comfortable and fast-comfortable whilst using each type of foot attachment. Moments and powers at the distal end of the prosthetic shank and at the intact joints of both limbs were compared between attachment conditions. There was no change in the amount of intact-limb ankle work across speed or attachment conditions. As speed level increased there was an increase on both limbs in the amount of hip and knee joint work done, and increases on the prosthetic side were greater when using the hyA-F. However, because all walking speed levels were higher when using the hyA-F, the intact-limb ankle and combined joints work per meter travelled were significantly lower; particularly so at the customary speed level. This was the case despite the hyA-F dissipating more energy during stance. In addition, the amount of eccentric work done per meter travelled became increased at the residual knee when using the hyA-F, with increases again greatest at customary speed. Findings indicate that a trans-tibial prosthesis incorporating a dynamic-response foot reduced speed-related changes in compensatory intact-limb joint kinetics when the foot was attached via an articulating hydraulic device compared to rigid attachment. As differences between attachment conditions were greatest at customary speed, findings indicate a hydraulic ankle-foot device is most effectual at the speed it is set-up for.

Various silicone elastomers have been evaluated for use in the prosthetic reconstruction of facial defects. Their strength, texture, flexibility, hardness, ease of preparation, pigment receptivity and retention, and their resistance to cleaning were compared and the data consulted when an elastomer was chosen to restore defects, improve aesthetics and reestablish the confidence of a selection of patients. Detailed case reports are provided, together with information on the adhesives or mechanical methods available for retaining the facial prosetheses. Cyanoacrylate adhesives for use on skin surfaces and as tissue adhesives have been studied in detail. A novel n-butyl 413 cyanoacrylate has been developed with a viscosity, haemostatic property and stability to make it particularly suitable for use in skin grafting and tissue repair. It has already been used with good results on patients with severe burns. An improved formulation, containing a fluorescent dye, can be precisely applied through a specially constructed foot-controlled dispenser illuminated by a fibre-optic supplying UV-light. Cyanoacrylates are already being used as tissue adhesives in place of the conventional but potentially disfiguring suture. The availability of improved, imperceptible adhesives and a precision applicator, which can be used in a modern operating theatre, will extend their effectiveness and satisfy some of the needs of Plastic, and Oral and Maxillo-Facial Surgeons. Portable applicators have potential use in battlefield and in veterinary surgery and overcome the imprecision characteristic of earlier methods. / Loctite UK

In the study the influence of different dental technical tools on the surface temperature and phase composition of fixed dental prostheses (FDPs) made of yttria-partially stabilized zirconia polycrystals (3Y-/4Y-/5Y-PSZ) was investigated. FDPs were fabricated by using computer-aided manufacturing (CAM). The FDPs were treated with a contra-angle handpiece equipped with different burs and polishers. The resulting surface temperatures were measured with a thermographic camera, and the resulting phase transformations were investigated by X-ray diffraction and quantified by Rietveld refinement. Processing with burs resulted in no phase transformation, but a preferred orientation shift. Using coarse polisher induced a phase transformation to the rhombohedral phase, while fine polishers produced no relevant phase transformations and no preferred orientation shift. Compared to the monoclinic phase (ca. 9% theoretical volume increase), which is associated with low-temperature degradation (LTD), the rhombohedral phase is much more voluminous (ca. 15% theoretical volume increase) and distorted and, therefore, has a greater degradation potential.

Completely digital workflows for the fabrication of implant-supported removable restorations are not yet common in clinical dental practice. The aim of the current case report is to illustrate a reliable and comfortable workflow that reasonably merges conventional and digital workflows for the CAD/CAM-fabrication of implant-supported overdentures. The 53-year old patient was supplied with a digitally processed complete denture in the upper jaw and, simultaneously, with an overdenture supported by four interforaminal implants in the lower jaw. The overdenture included a completely digitally processed and manufactured alloy framework that had been fabricated by selective laser sintering. The case report indicates that digital manufacturing processes for extensive and complex removable restorations are possible. However, as it is currently not yet possible to digitally obtain functional impressions, future developments and innovations might focus on that issue.

The aim of this study was to compare the clinical properties of tooth-colored computer-aided design/computer-aided manufacturing (CAD/CAM) materials for the fabrication of a 3-unit fixed dental prostheses (FDPs) in the same clinical scenario. A 53-year-old female patient was supplied with a 3-unit FDP to replace a second premolar in the upper jaw. Restorations were fabricated from 3 mol%, 4 mol%, and 5 mol% yttrium oxide zirconia, zirconia with translucency gradient, indirect composite resin, polyetheretherketone (PEEK), and polyetherketoneketone (PEKK). Milling time, weight, and radiopacity were investigated. Esthetics were examined following the US Public Health Service criteria (USPHS). The milling time for zirconia was twice as high as for the indirect composite resin, PEEK, or PEKK. The latter materials had a weight of 2 g each, while zirconia restorations yielded 5 g. Zirconia presented intense radiopacity. PEEK and PEKK required veneering and an opaquer was applied to the PEKK framework. All FDPs showed acceptable esthetics. PEEK and PEKK restorations were featured by a grayish shimmering. A variety of CAD/CAM materials are available to fabricate 3-unit FDPs with esthetically acceptable results. In the esthetic zone, PEEK and PEKK require veneering and an opaquer might be applied. Milling time, weight, and radiopacity were relatively high for zirconia FDPs.

In this prospective clinical trial we observed the 2-year clinical performance of posterior tooth-supported multi-unit fixed dental prostheses (FDP) fabricated from zirconia with monolithic occlusal surfaces. Fifty multi-unit FDPs were inserted in 50 patients. After two years of clinical service, 43 restorations were reexamined as one patient had died and six patients were not available for recall. Two biological (root canal treatment: 12 and 14 months) and one technical (debonding: 12 months) complications occurred. According to the Kaplan–Meier analysis, the success rate was 93.7%, and the survival rate was 100%. The six patients who were not available for regular 2-year follow-up were examined after the official 2-year recall interval, and none of the FDPs presented complications or failures. Within the limitations of the current study, the use of multi-unit FDPs with monolithic occlusal surfaces fabricated from zirconia can be recommended for short-term use in the posterior area.

The major objective of this thesis was to investigate how the use of a recently developed microprocessor-controlled limb system altered the negative mechanical work done by the intact and prosthetic limb when trans-femoral amputees terminated gait. Participants terminated gait on a level surface from their self-selected walking speed and on declined surface from slow and customary speeds, using limb system prosthesis with microprocessor active or inactive. Limb negative work, determined as the integral of the negative mechanical (external) limb power during the braking phase, was compared across surface, speed and microprocessor conditions. Halting gait was achieved predominantly from negative work done by the trailing/intact. Trailing versus leading limb mechanical work imbalance was similar to how able body individuals halted gait. Importantly, the negative limb work performed on the prosthetic side when terminating gait on declined surface was increased when the microprocessor was active for both slow and customary speeds (no difference on level surface) but no change on intact limb. This indicates the limb system’s ‘ramp-descent mode’ effectively/dynamically altered the hydraulic resistances at the respective joints with evidence indicating changes at the ankle were the key factor for increasing the prosthetic limb negative work contribution. Findings suggest that trans-femoral amputees became more assured using their prosthetic limb to arrest body centre of mass velocity when the limb system’s microprocessor was active. More generally findings suggest, trans-femoral amputees should obtain clinically significant biomechanical benefits from using a limb system prosthesis for locomotion involving adapting to their everyday walking where adaptations to an endlessly changing environment are required. / Higher Committee of Education Development in IRAQ (HCED)

No description available.

Syfte: Syftet med studien var att undersöka hur olika axiala tryck och skjuvkrafter påverkade marginal och intern passform i en sexledsbro i titan i överkäkens frontregion.Material och metod: En litteratursökning gjordes för att insamla bakgrundsmaterial. Stödtänderna 13 12 11 21 22 23 preparerades på en plastmodell för en sexledsbro och en anatomiskt utformad bro i titan framställdes med hjälp CAD/CAM. En mastermodell av stödtänderna tillverkades i epoxyresin. Genom att använda replikateknik utvärderades brons passform vid olika cementeringstryck; 20, 35, 50, 70 N och 50 N med skjuvkrafter. Varje replika snittades med hjälp av en ”jig” och cementspalten analyserades i ett mikroskop. All data granskades statistiskt.Resultat: Resultatet visade att ett tryck med 20 N generellt gav en ej acceptabel passform och ett tryck med 35 N hade en stor spridning. Vid tryck med 50 N kunde mindre cementspalter ses. De blev inte mindre vid test med 70 N. När skjuvkrafter adderades försämrades resultaten jämfört med försöken med 50 N och 70 N.Konklusion: Ett tryck vid cementering som överstiger 50 N förbättrar ej passformen markant. Närvaro av skjuvkrafter påverkar passformen negativt. Ett lägre tryck på 20 N ger dock en mindre fördelaktig passform jämfört med skjuvkrafter förutsatt att ett tillräckligt högt tryck används. Alla slutsatser var statistiskt signifikanta. / Purpose: The purpose of this study is to investigate how different axial seating loads and shear loads influences the marginal and internal fit of a titanium six unit FDP in the upper jaw frontal region.Materials and Methods: A literature search was made to acquire background material. Preparations of abutment teeth for a six unit FDP 13 12 11 21 22 23 were made on plastic teeth, and an anatomically designed titanium FDP was constructed using CAD/CAM. A master cast of the abutment teeth was fabricated in epoxy resin. Using the impression replica technique the fit of the FDP was evaluated by different seating loads during cementation; 20, 35, 50, 70 N and 50 N under the presence of shear loads. The replicas were sectioned using a jig and the cement gap was analysed using a microscope. All the data were statistically analysed.Results: The results showed that a seating load of 20 N generally gave an unacceptable fit and that the seating load of 35 N had great range. At seating loads of 50 N less cement gaps could be seen, i.e. more favourable fit. These results did not improve when testing with 70 N. With a presence of shear loads the results were poorer than when testing with 50 and 70 N.Conclusions: A seating load exceeding 50 N during cementation does not markedly give a more favourable fit. The presence of shear loads affects the fit negatively. A lower seating load of 20 N gives a less favourable fit compared to shear loads provided that a seating load high enough is used. All of these conclusions were statistically significant.

Syftet med detta projekt var att ta fram en lösning till det regelbundna bytet av proteser under barnets tillväxt. Problemet med detta regelbundna byte av proteser är materialkostnader, produktionskostnader, materialspill och materialanvändning som kommer vara kontinuerliga under barnets tillväxt och detta kan ha en negativ påverkan på aspekter som miljö, sociala och ekonomi. Detta projekt löstes igenom beslutsmodeller, skisser och 3D-konstruktioner som såg till att en protes hade förmågan att växa med ett barns tillväxt. Målet med examensarbetet var att konstruera en armprotes, skapa en fysisk prototyp och undersöka konstruktionens generella materialval. Dessutom ge argument för armprotesens fördelar kring de globala målen. Arbetet och resurserna som krävs för att konstruera en armprotes kräver extremt mycket forskning där detta examensarbete endast höll sig inom en liten ram. Detta examensarbete resulterade till en prototyp som kan demonstrera en expansionsfunktion och gripfunktion. Dessutom bestämdes lämpliga materialval för armprotesens olika komponenter. Projektet lyckades med att ta fram en lösning på det regelbundna bytet av proteser under ett barns tillväxt. Under projektets gång upptäcktes ett antal förbättringar som kunde utförts, då vid uppföljning av projekt togs det fram flera förbättringsförslag med hjälp av diskussion och resultat som senare går att jobba vidare med. / The purpose of this project was to develop a solution for the regular change of prostheses during a child’s growth. The problem with the regular change of prostheses are the material costs, production costs, material waste and material use which will be continuous during the child’s growth and this can have a negative impact on aspects such as enviormental, social and economical. his project was about developing a solution based on decision models, sketches and 3D-constructions that ensures that a prosthesis has the ability to expand with a child during it’s growth. The goal of the project was to construct a armprothesis, build a physical prototype and also research the general material choices. Furthermore provide arguments for the benefits of the specific prosthetic arm surrounding the sustainable development goals. The time and resources to develop such an arm prothesis will require en extreme amount of research, this thesis project would only be working within a small framework. This thesis project resulted in a prototyp that has the ability to demonstrate a expansionfunction and a grip function. Appropriate material choices were decided for the prothesis several components. The project succeded in producing a solution for the regular change of prostheses during a child’s growth. During the course of the project was it realized that several improvements could’ve been made, then at the behest of a sudden follow-up, several suggestions for improvement were produced with the help of discussion and results which can late be worked upon.