Communication and reconnaissance systems are requiring increasing flexibility concerning functionality and efficiency for multiband and broadband frequency applications. Circuit-based reconfiguration mechanisms continue to promote radio frequency (RF) application flexibility; however, increasing limitations have resulted in hindering performance. Therefore, the implementation of a "wireless" reconfiguration mechanism provides the required agility and amicability for microwave circuits and antennas without local overhead. The wireless reconfiguration mechanism in this thesis integrates dynamic, fluidic-based material systems to achieve electromagnetic agility and reduce the need for "wired" reconfiguration technologies. The dynamic material system component has become known as electromagnetically functionalized colloidal dispersions (EFCDs). In a microfluidic reconfiguration system, they provide electromagnetic agility by altering the colloidal volume fraction of EFCDs - their name highlights the special considerations we give to material systems in applied electromagnetics towards lowering loss and reducing system complexity. Utilizing EFCDs at the RF device-level produced the first circuit-type integration of this reconfiguration system; this is identified as the coaxial stub microfluidic impedance transformer (COSMIX). The COSMIX is a small hollowed segment of transmission line with results showing a full reactive loop (capacitive to inductive tuning) around the Smith chart over a 1.2 GHz bandwidth. A second microfluidic application demonstrates a novel antenna reconfiguration mechanism for a 3 GHz microstrip patch antenna. Results showed a 300 MHz downward frequency shift by dielectric colloidal dispersions. Magnetic material produced a 40 MHz frequency shift. The final application demonstrates the dynamically altering microfluidic system for a 3 GHz 1x2 array of linearly polarized microstrip patch antennas. The parallel microfluidic capillaries were imbedded in polydimethylsiloxane (PDMS). Both E- and H-plane designs showed a 250 MHz frequency shift by dielectric colloidal dispersions. Results showed a strong correlation between decreasing electrical length of the elements and an increase of the volume fraction, causing frequency to decrease and mutual coupling to increase. Measured, modeled, and analytical results for impedance, voltage standing wave ratio (VSWR), and radiation behavior (where applicable) are provided.

The performance of commercial Radio Frequency Identification (RFID) tags is primarily limited by present techniques used for tag antenna design. Currently, industry techniques rely on identifying the RFID tag application (books, clothing, etc.) and then building antenna prototypes of different configurations in order to satisfy minimum read range requirements. However, these techniques inherently lack an electromagnetic basis and are unable to provide a low cost solution to the tag antenna design process. RFID tag performance characteristics (read-range, chip-antenna impedance matching, surrounding environment) can be very complex, and a thorough understanding of the RFID tag antenna design may be gained through an electromagnetic approach in order to reduce the tag antenna size and the overall cost of the RFID system. The research presented in this thesis addresses RFID tag antenna design process for passive RFID tags. With the growing number of applications (inventory, supply-chain, pharmaceuticals, etc), the proposed RFID antenna design process demonstrates procedures to design tag antennas for such applications. Electrical/geometrical properties of the antennas designed were investigated with the help of computer electromagnetic simulations in order to achieve optimal tag performance criteria such as read range, chip-impedance matching, antenna efficiency, etc. Experimental results were performed on the proposed antenna designs to compliment computer simulations and analytical modelling.

Ultra-cold dilute gases of neutral atoms are attractive candidates for creating controlled mesoscopic quantum systems. In particular, quantum degenerate gases of bosonic and fermionic atoms can be used to model the correlated many-body behaviour of Bose and Fermi condensed matter systems, and to study matter wave interference and coherence. This thesis describes the experimental realization and manipulation of Bose-Einstein condensates (BECs) of 87Rb and degenerate Fermi gases (DFGs) of 40K using static and dynamic magnetic atom chip traps. Atom chips are versatile modern tools used to manipulate atomic gases. The chips consist of micrometre-scale conductors supported by a planar insulating substrate, and can be used to create confining potentials for neutral atoms tens or hundreds of micrometres from the chip surface. We demonstrate for the first time that a DFG can be produced via sympathetic cooling with a BEC using a simple single-vacuum-chamber apparatus. The large 40K-87Rb collision rate afforded by the strongly confining atom chip potential permits rapid cooling of 40K to quantum degeneracy via sympathetic cooling with 87Rb. By studying 40K-87Rb cross-thermalization as a function of temperature, we observe the Ramsauer-Townsend reduction in the 40K-87Rb elastic scattering cross-section. We achieve DFG temperatures as low as T = 0.1TF , and observe Fermi pressure in the time-of-flight expansion of the gas. This thesis also describes the radio-frequency (RF) manipulation of trapped atoms to create dressed state double-well potentials for BEC and DFG.We demonstrate for the first time that RF-dressed potentials are species-selective, permitting the formation of simultaneous 87Rb double-well and 40K single-well potentials using a 40K-87Rb mixture. We also develop tools to measure fluctuations of the relative atom number and relative phase of a dynamically split 87Rb BEC. In particular, we observe atom number fluctuations at the shot-noise level using time-of-flight absorption imaging. These measurement tools lay the foundation for future investigations of number squeezing and matter wave coherence in BEC and DFG systems.

Ultra-cold dilute gases of neutral atoms are attractive candidates for creating controlled mesoscopic quantum systems. In particular, quantum degenerate gases of bosonic and fermionic atoms can be used to model the correlated many-body behaviour of Bose and Fermi condensed matter systems, and to study matter wave interference and coherence. This thesis describes the experimental realization and manipulation of Bose-Einstein condensates (BECs) of 87Rb and degenerate Fermi gases (DFGs) of 40K using static and dynamic magnetic atom chip traps. Atom chips are versatile modern tools used to manipulate atomic gases. The chips consist of micrometre-scale conductors supported by a planar insulating substrate, and can be used to create confining potentials for neutral atoms tens or hundreds of micrometres from the chip surface. We demonstrate for the first time that a DFG can be produced via sympathetic cooling with a BEC using a simple single-vacuum-chamber apparatus. The large 40K-87Rb collision rate afforded by the strongly confining atom chip potential permits rapid cooling of 40K to quantum degeneracy via sympathetic cooling with 87Rb. By studying 40K-87Rb cross-thermalization as a function of temperature, we observe the Ramsauer-Townsend reduction in the 40K-87Rb elastic scattering cross-section. We achieve DFG temperatures as low as T = 0.1TF , and observe Fermi pressure in the time-of-flight expansion of the gas. This thesis also describes the radio-frequency (RF) manipulation of trapped atoms to create dressed state double-well potentials for BEC and DFG.We demonstrate for the first time that RF-dressed potentials are species-selective, permitting the formation of simultaneous 87Rb double-well and 40K single-well potentials using a 40K-87Rb mixture. We also develop tools to measure fluctuations of the relative atom number and relative phase of a dynamically split 87Rb BEC. In particular, we observe atom number fluctuations at the shot-noise level using time-of-flight absorption imaging. These measurement tools lay the foundation for future investigations of number squeezing and matter wave coherence in BEC and DFG systems.

Next generation mobile communication systems require the use of linear RF power amplifier for higher data transmission rates. However, linear RF power amplifiers are inherently inefficient and usually require additional circuits or further system adjustments for better efficiency. This dissertation focuses on the development of new efficiency enhancement schemes for linear RF power amplifiers. The multistage Doherty amplifier technique is proposed to improve the performance of linear RF power amplifiers operated in a low power level. This technique advances the original Doherty amplifier scheme by improving the efficiency at much lower power level. The proposed technique is supported by a new approach in device periphery calculation to reduce AM/AM distortion and a further improvement of linearity by the bias adaptation concept. The device periphery adjustment technique for efficiency enhancement of power amplifier integrated circuits is also proposed in this work. The concept is clearly explained together with its implementation on CMOS and SiGe RF power amplifier designs. Furthermore, linearity improvement technique using the cancellation of nonlinear terms is proposed for the CMOS power amplifier in combination with the efficiency enhancement technique. In addition to the efficiency enhancement of power amplifiers, a scalable large-signal MOSFET model using the modified BSIM3v3 approach is proposed. A new scalable substrate network model is developed to enhance the accuracy of the BSIM3v3 model in RF and microwave applications. The proposed model simplifies the modeling of substrate coupling effects in MOS transistor and provides great accuracy in both small-signal and large-signal performances.

This thesis discusses the investigation and utilization of a new promising thin-film material, liquid crystal polymer (LCP), for microwave and millimeter-wave (mm-wave [>30 GHz]) components and packages. The contribution of this research is in the determination of LCP's electrical and mechanical properties as they pertain to use in radio frequency (RF) systems up to mm-wave frequencies, and in evaluating LCP as a low-cost substrate and packaging material alternative to the hermetic materials traditionally desired for microwave circuits at frequencies above a few gigahertz (GHz). A study of LCP's mm-wave material properties was performed. Resonant circuit structures were designed to find the dielectric constant and loss tangent from 2-110 GHz under both ambient and elevated temperature conditions. Several unique processes were developed for the realization of novel multilayer LCP-based RF circuits. These processes include thermocompression bonding with tight temperature control (within a few degrees Celsius), precise multilayer alignment and patterning, and LCP laser processing with three different types of lasers. A proof-of-concept design that resulted from this research was a dual-frequency dual-polarization antenna array operating at 14 and 35 GHz. Device characterization such as mechanical flexibility testing of antennas and seal testing of packages were also performed. A low-loss interconnect was developed for laser-machined system-level thin-film LCP packages. These packages were designed for and measured with both RF micro-electromechanical (MEM) switches and monolithic microwave integrated circuits (MMICs). These research findings have shown LCP to be a material with uniquely attractive properties/capabilities for vertically integrated, compact multilayer LCP circuits and modules.

Communication and reconnaissance systems are requiring increasing flexibility concerning functionality and efficiency for multiband and broadband frequency applications. Circuit-based reconfiguration mechanisms continue to promote radio frequency (RF) application flexibility; however, increasing limitations have resulted in hindering performance. Therefore, the implementation of a "wireless" reconfiguration mechanism provides the required agility and amicability for microwave circuits and antennas without local overhead. The wireless reconfiguration mechanism in this thesis integrates dynamic, fluidic-based material systems to achieve electromagnetic agility and reduce the need for "wired" reconfiguration technologies. The dynamic material system component has become known as electromagnetically functionalized colloidal dispersions (EFCDs). In a microfluidic reconfiguration system, they provide electromagnetic agility by altering the colloidal volume fraction of EFCDs - their name highlights the special considerations we give to material systems in applied electromagnetics towards lowering loss and reducing system complexity. Utilizing EFCDs at the RF device-level produced the first circuit-type integration of this reconfiguration system; this is identified as the coaxial stub microfluidic impedance transformer (COSMIX). The COSMIX is a small hollowed segment of transmission line with results showing a full reactive loop (capacitive to inductive tuning) around the Smith chart over a 1.2 GHz bandwidth. A second microfluidic application demonstrates a novel antenna reconfiguration mechanism for a 3 GHz microstrip patch antenna. Results showed a 300 MHz downward frequency shift by dielectric colloidal dispersions. Magnetic material produced a 40 MHz frequency shift. The final application demonstrates the dynamically altering microfluidic system for a 3 GHz 1x2 array of linearly polarized microstrip patch antennas. The parallel microfluidic capillaries were imbedded in polydimethylsiloxane (PDMS). Both E- and H-plane designs showed a 250 MHz frequency shift by dielectric colloidal dispersions. Results showed a strong correlation between decreasing electrical length of the elements and an increase of the volume fraction, causing frequency to decrease and mutual coupling to increase. Measured, modeled, and analytical results for impedance, voltage standing wave ratio (VSWR), and radiation behavior (where applicable) are provided.

Frequency selective surfaces (FSSs) provide a variety of spatial filtering functions, such as band-pass or band-stop properties in a radome or other multilayer structure. This filtering is typically achieved through closely-spaced periodic arrangements of metallic shapes on top of a dielectric substrate (or within a stack of dielectric materials). In most cases, the unit cell size, its shape, the substrate parameters, and the inter-element spacing collectively impact the response of the FSS. Expanding this design space to include reconfigurable FSSs provides opportunities for applications requiring frequency agility and/or other properties. Tuning can also enable operation over a potentially wider range of frequencies and can in some cases be used as a loading mechanism or quasi-ground plane. Many technologies have been considered for this type of agility (RF MEMS, PIN diodes, etc.). This includes the recent use of microfluidics and dispersions of nanoparticles, or fluids with controllable dielectrics, which have entered the design space of numerous other EM applications including stub-tuners, antennas, and filters. In this work they provide a material based approach to reconfiguring an FSS. An FSS based on a four-arm spiral with tunable band-stop characteristics is presented in this work. A thin colloidal dispersion above each element provides this tuning capability. The radial expansion and contraction of this dispersion, as well as the variable permittivity of the dispersion, are used to load each element individually. This design incorporates thin fluidic channels within a PDMS layer below the substrate leading to individual unit cells that provide a closed pressure-driven subsystem that contains the dispersion. With the capability to individually control each cell, groups of cells can be locally altered (individually or in groups) to create gratings and other electromagnetically agile features across the surface or within the volume of a radome or other covering. Simulations and measurements of an S-band tunable design using colloidal Barium Strontium Titanate dispersed Silicone oil are provided to demonstrate the capability to adjust the stop-band characteristics of the FSS across the S-band.

Fundamental features of Radio Frequency Identification (RFID) systems used in different application areas will be reviewed. Techniques used in realizing RFID antenna systems will be studied and the procedure to realize a specific RFID antenna type possessing desired characteristics will be described. Electrical properties such as radiation pattern, impedance will be predicted using analytical and/or computer simulation techniques. Experimental investigations will be carried out to complement the theoretical work.

Lignocellulosic biomass is composed of cellulose, hemicellulose, lignin and extraneous compounds (waxes, fats, gums, starches, alkaloids, resins, tannins, essential oils, silica, carbonates, oxalates, etc). The sugars within the complex carbohydrates (cellulose and hemicellulose) can be accessed for cellulosic bioethanol production through ethanologenic microorganisms. However, the composite nature of lignocellulosic biomass, particularly the lignin portion, presents resistance and recalcitrance to biological and chemical degradation during enzymatic hydrolysis/saccharification and the subsequent fermentation process. This leads to a very low conversion rate, which makes the process uneconomically feasible. Thus, biomass structure requires initial breakdown of the lignocellulosic matrix. In this study, two types of biomass pretreatment were applied on barley straw grind: radio-frequency (RF)-based dielectric heating technique using alkaline (NaOH) solution as a catalyst and steam explosion pretreatment at low severity factor. The pretreatment was applied on barley straw which was ground in hammer mill with a screen size of 1.6 mm, so as to enhance its accessibility and digestibility by enzymatic reaction during hydrolysis. Three levels of temperature (70, 80, and 90oC), five levels of ratio of biomass to 1% NaOH solution (1:4, 1:5, 1:6, 1:7, & 1:8), 1 h soaking time, and 20 min residence time were used for the radio frequency pretreatment. The following process and material variables were used for the steam explosion pretreatment: temperature (140-180oC), retention time (5-10 min), and 8-50% moisture content (w.b). The effect of both pretreatments was assessed through chemical composition analysis and densification of the pretreated and non-pretreated biomass samples. Results of this investigation show that lignocellulosic biomass absorbed more NaOH than water, because of the hydrophobic nature of lignin, which acts as an external crosslink binder on the biomass matrix and shields the hydrophilic structural carbohydrates (cellulose and hemicellulose). It was observed in the RF pretreatment that the use of NaOH solution and the ratio of biomass to NaOH solution played a major role, while temperature played a lesser role in the breakdown of the lignified matrix, as well as in the production of pellets with good physical quality. The heat provided by the RF is required to assist the alkaline solution in the deconstruction and disaggregation of lignocellulosic biomass matrix. The disruption and deconstruction of the lignified matrix is also associated with the dipole interaction, flip flop rotation, and friction generated between the electromagnetic charges from the RF and the ions and molecules from the NaOH solution and the biomass. The preserved cellulose from the raw sample (non-treated) was higher than that from the RF alkaline pretreated samples because of the initial degradation of the sugars during the pretreatment process. The same observation applies to hemicellulose. This implies that there is a trade-off between the breakdown of the biomass matrix/creating pores in the lignin and enhancing the accessibility and digestibility of the cellulose and hemicellulose. The use of dilute NaOH solution in biomass pretreatment showed that the higher the NaOH concentration, the lower was the acid insoluble lignin and the higher was the solubilized lignin moieties. The ratio of 1:6 at the four temperatures studied was determined to be the optimal. Based on the obtained data, it is predicted that this pretreatment will decrease the required amount and cost of enzymes by up to 64% compared to using non-treated biomass. However, the use of NaOH led to an increase in the ash content of biomass. The ash content increased with the decreasing ratio of biomass to NaOH solution. This problem of increased ash content can be addressed by washing the pretreated samples. RF assisted-alkaline pretreatment technique represents an easy to set-up and potentially affordable route for the bio-fuel industry, but this requires further energy analysis and economic validation, so as to investigate the significant high energy consumption during the RF-assisted alkaline pretreatment heating process. Data showed that in the steam explosion (SE) pretreatment, considerable thermal degradation of the energy potentials (cellulose and hemicellulose) with increasing acid soluble and insoluble lignin content occurred. The high degradation of the hemicellulose can be accounted for by its amorphous nature which is easily disrupted by external influences unlike the well-arranged crystalline cellulose. It is predicted that this pretreatment will decrease the required amount and cost of enzymes by up to 33% compared to using non-treated biomass.The carbon content of the solid SE product increased at higher temperature and longer residence time, while the hydrogen and oxygen content decreased. The RF alkaline and SE treatment combinations that resulted to optimum yield of cellulose and hemicellulose were selected and then enzymatically digested with a combined mixture of cellulase and β-glucosidase enzymes at 50oC for 96 h on a shaking incubator at 250 rev/min. The glucose in the hydrolyzed samples was subsequently quantified. The results obtained confirmed the effectiveness of the pretreatment processes. The average available percentage glucose yield that was released during the enzymatic hydrolysis for bioethanol production ranged from 78-96% for RF-alkaline pretreated and 30-50% for the SE pretreated barley straw depending on the treatment combination. While the non-treated sample has available average percentage glucose yield of just below 12%. The effects of both pretreatment methods (RF and SE) were further evaluated by pelletizing the pretreated and non-pretreated barley straw samples in a single pelleting unit. The physical characteristics (pellet density, tensile strength, durability rating, and dimensional stability) of the pellets were determined. The lower was the biomass:NaOH solution ratio, the better was the quality of the produced pellets. Washing of the RF-alkaline pretreated samples resulted in pellets with low quality. A biomass:NaOH solution ratio of 1:8 at the three levels of temperature (70, 80, and 90oC) studied are the RF optimum pretreatment conditions. The higher heating value (HHV) and the physical characteristics of the produced pellets increased with increasing temperature and residence time. The steam exploded samples pretreated at higher temperatures (180ºC) and retention time of 10 min resulted into pellets with good physical qualities. Fourier transform infrared-photoacoustic spectroscopy (FTIR-PAS) was further applied on the RF alkaline and SE samples in light of the need for rapid and easy quantification of biomass chemical components (cellulose, hemicellulose, and lignin). The results obtained show that the FTIR-PAS spectra can be rapidly used for the analysis and identification of the chemical composition of biofuel feedstock. Predictive models were developed for each of the biomass components in estimating their respective percentage chemical compositions.