L'étude de l'injection d'un fluide dans des conditions de hautes pressions reste encore aujourd'hui un challenge. Lorsque la pression critique des fluides est dépassée, l'état supercritique est atteint, faisant disparaître la distinction entre liquide et gaz. Pour ces conditions extrêmes, les données expérimentales sont peu nombreuses et nécessitent d'être consolidées. Dans cette étude, un nouveau banc d'essai a été réalisé au laboratoire CORIA dans le but d'étudier des injections non-réactives d'éthane et de propane dans une atmosphère sub- et supercritique d'azote ou d'hélium. Les données ont été collectées à partir de quatre diagnostics optiques : l'ombroscopie, la DBI, la radiographie et la CBOS. Des informations qualitatives sur la topologie des jets et de leur couche de mélange sont apportées. Des mesures quantitatives de longueur de cœur dense, d'angle d'ouverture et de densité sont complétées par une étude phénoménologique à l'aide de la théorie des mélanges binaires. / Studying a fluid flow under high-pressure conditions through reliable experiments is still nowadays a challenge. When the chamber pressure exceeds the critical pressure of working fluids the supercritical state of matter is reached and the distinction between gas and liquid becomes blurred. For such special conditions, experimental data are scarce and need to be consolidated. In the present study, a new test bench has been designed at CORIA Lab to study the non-reactive injection of ethane and propane into nitrogen or helium under sub- and supercritical conditions. Experimental data are collected from four image-based techniques : shadowgraphy, diffused backlight illumination (DBI), radiography and color background oriented schlieren (CBOS). Qualitative information on topology of the jets and their mixing layer are provided. Quantitative measurements of dense core length, jet spreading angle and density field are supported by a phenomenological study based on binary mixing theory.

<p>Nanosecond spark plasma actuators provide an opportunity to reduce pollutants by promoting efficient combustion in engines or provide targeted, tunable, flow control over vehicles, due to their ability to influence flow and combustion through multiple mechanisms. The plasma actuators can be physically unobtrusive, can be turned on and off and their low duty cycle, large bandwidth, and light weight make them more appealing than other control approaches. One method by which these plasma actuators interact with the environment is by inducing a complex local flow field and in order, to design scalable, high frequency actuators effectively, it is necessary to first understand the flow induced by a single spark discharge. Most experimental analysis on the flow induced by spark discharges has been restricted to qualitative descriptions of the flow field, primarily due to the difficulties associated with measuring such a transient and highly complex flow with sufficient spatiotemporal resolution. Quantitative, experimental characterization of the flow induced by a spark discharge remains lacking. </p><p> </p><p>A spark discharge produces a shock wave and a hot gas kernel with a complex flow field following the shock. In this work, combined experimental and theoretical characterization of the spark induced flow is performed through a series of high spatiotemporal resolution measurements of the density and velocity fields and reduced-order modeling. The work investigates the mechanisms driving the cooling and vorticity generation in spark induced flow and the 3D nature of the flow field. Planar (2D-3C) and volumetric (3D-3C) velocity measurements are taken using stereoscopic particle image velocimetry (SPIV) and tomographic PIV, respectively. Density measurements are taken using background oriented schlieren (BOS) and high speed schlieren imaging is used to capture the shock wave induced by the spark.</p><p> </p><p>The work shows that spark plasma discharges induce vortex rings whose vorticity is likely generated due to baroclinic torque arising from the non-uniform strength of the induced shock wave. The hot gas kernel cools in two stages: an initially fast cooling regime, followed by a slower cooling process. Reduced order analytical models are developed to describe the cooling observed in the fast regime and the role of the vortex rings in the entrainment of cold ambient gas and the cooling of the hot gas kernel. The results show that the vortex rings entrain ambient gas and drive cooling in the fast, convective regime, cooling approximately 50% of the hot gas within the first millisecond of the induced flow. An increase in the electrical energy deposited in the spark gap increases the shock strength and curvature and increases the vortex ring strength, thereby increasing the cooling rate and expansion of the hot gas kernel. The volumetric velocity measurements capture one of the two induced vortex rings and provide a framework for the improvements needed in future tomographic PIV experiments of the spark induced flow field, necessary in assessing the 3D nature of the induced vortex rings.</p><p> </p><p> The results of this work provide the first set of quantitative, experimental data on flow induced by nanosecond spark discharges that can be used for validation of computational fluid dynamics (CFD) simulations. The results demonstrate that spark plasmas induce vortex ring-driven mixing flows and the results on mixing and cooling of the hot gas kernel can be extended to any passive scalars present in the flow field as well as inform pulsation frequencies and actuator designs for flow and combustion control. The results from the reduced order modeling can inform future studies and applications of nanosecond spark discharges and can be extended to a variety of other types of plasma discharges like laser sparks, long duration sparks and surface discharges with similar induced flow fields.<br></p>

The hypersonic laminar to turbulent transition problem above Mach 10 is addressed experimentally in the short duration VKI Longshot gun tunnel. Reentry conditions are partially duplicated in terms of Mach and Reynolds numbers. Pure nitrogen is used as a test gas with flow enthalpies sufficiently low to avoid its dissociation, thus approaching a perfect gas behavior. The stabilizing effects of Mach number and nosetip bluntness on the development of natural boundary layer disturbances are evaluated over a 7 degrees half-angle conical geometry without angle of attack. <p><p>Emphasis is initially placed on the flow characterization of the Longshot wind tunnel where these experiments are performed. Free-stream static pressure diagnostics are implemented in order to complete existing stagnation point pressure and heat flux measurements on a hemispherical probe. An alternative method used to determine accurate free-stream flow conditions is then derived following a rigorous theoretical approach coupled to the VKI Mutation thermo-chemical library. Resulting sensitivities of free-stream quantities to the experimental inputs are determined and the corresponding uncertainties are quantified and discussed. The benefits of this different approach are underlined, revealing the severe weaknesses of traditional methods based on the measurement of reservoir conditions and the following assumptions of an isentropic and adiabatic flow through the nozzle. The operational map of the Longshot wind tunnel is redefined accordingly. The practical limits associated with the onset of nitrogen flow condensation under non-equilibrium conditions are also accounted for. <p><p>Boundary layer transition experiments are then performed in this environment with free-stream Mach numbers ranging between 10-12. Instrumentation along the 800mm long conical model includes flush-mounted thermocouples and fast-response pressure sensors. Transition locations on sharp cones compare favorably with engineering correlations. A strong stabilizing effect of nosetip bluntness is reported and no transition reversal regime is observed for Re_RN<120000. Wavelet analysis of wall pressure traces denote the presence of inviscid instabilities belonging to Mack's second mode. An excellent agreement with Linear Stability Theory results is obtained from which the N-factor of the Longshot wind tunnel in these conditions is inferred. A novel Schlieren technique using a short duration laser light source is developed, allowing for high-quality flow visualization of the boundary layer disturbances. Comparisons of these measurement techniques between each other are finally reported, providing a detailed view of the transition process above Mach 10. / Doctorat en Sciences de l'ingénieur / info:eu-repo/semantics/nonPublished

Die vorwiegend experimentelle Arbeit befasst sich mit der systematischen Untersuchung von Parametervariationen bei der aktiven Strömungskontrolle mit elektromagnetischen Kräften. An einer angestellten Platte und einem NACA0015-Profil wurde die saugseitige abgelöste Strömung durch das Einbringen einer periodischen wandparallelen Lorentzkraft an der Vorderkante beeinflusst und experimentell mittels zeitaufgelöster Particle Image Velocimetry (PIV) untersucht. Dabei wurde für verschiedene Anstellwinkel und Reynoldszahlen die Frequenz der Anregung, deren Impulseintrag und der zeitliche Kraftverlauf variiert. Strömungsmechanische Untersuchungen experimenteller und numerischer Natur wurden für eine elektrochemische Zelle und den Fall der Elektrolyse an Millieelektroden unter dem Einfluss externer Magnetfelder durchgeführt. Die Übereinstimmung der gemessenen und berechneten Geschwindigkeitsfelder war dabei sehr gut. Entgegen der Annahme, dass im Falle homogener Magnetfelder keine Strömungen induziert werden, konnte nachgewiesen werden, dass durch die lokale Krümmung der elektrischen Feldlinien in Elektrodennähe starke Lorentzkräfte generiert werden. Dies führt zu sehr komplexen Primär-und Sekundärströmungen. Die gleichen Effekte bewirken ebenfalls in der Nähe von Millieelektroden starke Lorentzkräfte in homogenen magnetischen Feldern. Die experimentellen Beobachtungen an Millieelektroden von Leventis et. al (2005), welche zum Beweis der Konzentrationsgradientenkraft herangezogen wurden, konnten alle auf das Wirken lokaler Lorentzkräfte zurückgeführt werden. Der experimentelle Nachweis der Konzentrationsgradientenkraft steht damit weiterhin aus. Zur Messung der Konzentrationen in elektrochemischen Systemen wurde erstmals das Hintergrundschlierenverfahren angewendet. Dieses Verfahren erlaubt die Bestimmung der räumlichen Konzentrationsgradienten mit erheblich weniger messtechnischen Aufwand gegenüber spektroskopischen Methoden und der Schlierentechnik.

[ES] En un presente marcado por la continua lucha contra la contaminación y el cambio climático, la investigación en mejoras tecnológicas que permitan una transición aceptable para la sociedad hacia un futuro más ecológico ocupa un papel fundamental. En concreto, la aviación es un foco constante de innovación, ya que es considerada una función indispensable en una sociedad tan globalizada como la actual, pero con unos niveles de contaminación preocupantes. En este aspecto, el desarrollo de motores con altas eficiencias es un paso clave para la transición medioambiental. Sin embargo, estas alternativas presentan un reto tecnológico en cuanto a su gestión térmica basado, principalmente, en la necesidad de aumentar la refrigeración. En este contexto e impulsada por el proyecto "Aerodynamic upgrade of Surface Air Cooled Oil Cooler (SACOC)" de Clean Sky 2, esta tesis doctoral se centra en el estudio experimental de geometrías de intercambiadores de calor de superficie para la refrigeración del aceite motor mediante el uso del aire del flujo secundario del turbofan. Actualmente, existen una serie de limitaciones en cuanto a las capacidades para llevar a cabo un análisis y diseño detallado de este tipo de intercambiadores de calor debido a la falta de instalaciones que permitan un correcta, completa y robusta caracterización experimental. Las principales fuentes de datos se basan en cálculos numéricos validados a partir de extrapolaciones en condiciones de cuestionable aplicabilidad. A lo largo de la tesis se presentan los resultados obtenidos tras una detallada caracterización de cuatro diferentes geometrías de intercambiadores de calor empleando tanto técnicas intrusivas como ópticas. Se utiliza un banco de flujo capaz de generar una corriente de aire típica alrededor de los intercambiadores, mientras que un sistema de acondicionamiento de aceite controla el punto de operación por el lado caliente. Para recrear de manera más realista las condiciones de funcionamiento, se presenta una metodología para generar de manera automática pantallas de distorsión que pueden reproducir una distribución bidimensional de velocidades objetivo mediante la manufactura aditiva de paneles de porosidad variable. Este modelo, analizado mediante CFD y validado experimentalmente, se utiliza para reproducir el perfil de velocidades típico presente en torno al intercambiador en una circunstancia real de operación. Tras definir métricas relevantes que permitan analizar el comportamiento de las distintas geometrías, se llega a la conclusión de que los problemas aerodinámico y térmico están altamente acoplados en estos dispositivos, demostrando la necesidad de un cuidadoso diseño para mejorar las actuaciones del intercambiador. Los resultados muestran que puede llegar a obtenerse una mejora de más de un 12% en la caída de presión y casi un 20% en el intercambio de calor. Además, se ha confirmado el impacto del uso de la pantalla de distorsión, con variaciones del orden de 10% en ambas variables. Los resultados también muestran que es posible realizar una caracterización preliminar de manera fiable con un modelo impreso en 3D, en cuanto campos de velocidades, pérdidas de presión y frecuencias propias corregidas. Con el análisis llevado a cabo en esta tesis, se puede concluir que es fundamental tener una instalación experimental que reproduzca las condiciones de funcionamiento reales de un motor para realizar estudios relevantes de intercambiadores de calor. Además, es necesario el uso de métricas adecuadas junto con el desarrollo de una metodología exhaustiva, fiable y robusta. Los resultados y metodología presentados en en esta investigación pueden llegar a tener un impacto importante tanto a nivel académico como industrial, ya que abren la puerta a desarrollar sistemas de gestión térmica más eficiente en unas etapas de diseño preliminares que son más asequibles económicamente, consumen menos tiempo y tienen mayor flexibilidad para introducir modificaciones. / [CAT] En un present marcat per la lluita contínua contra la contaminació i el canvi climàtic, la recerca en millores tecnològiques que permetin una transició acceptable per a la societat cap a un futur més ecològic ocupa un paper fonamental. En concret, l'aviació és un focus constant d'innovació, ja que és considerada una funció indispensable en una societat tan globalitzada com l'actual però amb uns nivells de contaminació preocupants. En aquest aspecte, el desenvolupament de motors amb altes eficiències és un pas clau per a la transició mediambiental. Tot i això, aquestes alternatives presenten un repte tecnològic quant a la seva gestió tèrmica basat, principalment, en la necessitat d'augmentar la refrigeració. En aquest context i impulsada pel projecte "Aerodynamic upgrade of Surface Air Cooled Oil Cooler (SACOC)" de Clean Sky 2, aquesta tesi doctoral se centra en l'estudi experimental de geometries d'intercanviadors de calor de superfície per a la refrigeració de l'oli motor mitjançant l'ús de l'aire del flux secundari del turbofan. Actualment, hi ha una sèrie de limitacions quant a les capacitats per dur a terme una anàlisi i disseny detallat d'aquest tipus d'intercanviadors de calor a causa de la manca d'instal·lacions que permetin una caracterització experimental correcta, completa i robusta. Les fonts de dades principals es basen en càlculs numèrics validats a partir d'extrapolacions en condicions de qüestionable aplicabilitat. Al llarg de la tesi es presenten els resultats obtinguts després d'una detallada caracterització de quatre geometries diferents d'intercanviadors de calor emprant tant tècniques intrusives com òptiques. Sutilitza un banc de flux capaç de generar un corrent daire típic al voltant dels intercanviadors, mentre que un sistema de condicionament doli controla el punt doperació pel costat calent. Per recrear de manera més realista les condicions de funcionament, es presenta una metodologia per generar de manera automàtica pantalles de distorsió que poden reproduir una distribució bidimensional de velocitats objectiu mitjançant la manufactura additiva de panells de porositat variable. Aquest model, analitzat mitjançant CFD i validat experimentalment, sutilitza per reproduir el perfil de velocitats típic present al voltant de lintercanviador en una circumstància real doperació. Després de definir mètriques rellevants que permetin analitzar el comportament de les diferents geometries, s'arriba a la conclusió que els problemes aerodinàmic i tèrmic estan altament acoblats en aquests dispositius, demostrant la necessitat d'un disseny acurat per millorar les actuacions de l'intercanviador. Els resultats mostren que es pot arribar a obtenir una millora de més d'un 12% a la caiguda de pressió i gairebé un 20% a l'intercanvi de calor. A més, s'ha confirmat l'impacte de l'ús de la pantalla de distorsió, amb variacions de l'ordre del 10% a les dues variables. Els resultats també mostren que és possible fer una caracterització preliminar de manera fiable amb un model imprès en 3D, en tant que camps de velocitats, pèrdues de pressió i freqüències pròpies corregides. Amb l'anàlisi duta a terme en aquesta tesi, es pot concloure que és fonamental tenir una instal·lació experimental que reprodueixi les condicions de funcionament reals d'un motor per fer estudis rellevants d'intercanviadors de calor. A més, cal fer servir mètriques adequades juntament amb el desenvolupament d'una metodologia exhaustiva, fiable i robusta. Els resultats i metodologia presentats en aquesta investigació poden arribar a tenir un impacte important tant a nivell acadèmic com industrial, ja que obren la porta a desenvolupar sistemes de gestió tèrmica més eficient en unes etapes de disseny preliminars que són més assequibles econòmicament, consumeixen menys temps i tenen més flexibilitat per introduir modificacions. / [EN] In a present marked by the continuous fight against pollution and climate change, research into technological improvements that allow an acceptable transition for society towards a greener future occupies a fundamental role. Specifically, aviation is a constant focus of innovation, since it is considered an essential function in a society as globalized as today's, but with worrying levels of pollution. In this regard, the development of motors with high efficiencies is a key step for the environmental transition. However, these alternatives present a technological challenge in terms of their thermal management, based mainly on the need to increase cooling. In this context and promoted by the Clean Sky 2 "Aerodynamic upgrade of Surface Air Cooled Oil Cooler (SACOC)" project, this doctoral thesis focuses on the experimental study of surface heat exchanger geometries for engine oil cooling using the use of secondary flow air from the turbofan. Currently, there are a number of limitations regarding the capacity to carry out a detailed analysis and design of this type of heat exchanger due to the lack of facilities that allow a correct, complete and robust experimental characterization. The main data sources are based on numerical calculations validated from extrapolations under conditions of questionable applicability. The thesis presents results after a detailed characterization of four different geometries of heat exchangers using both intrusive and optical techniques. A flow bench capable of generating a typical air current around the exchangers is used, while an oil conditioning system controls the point of operation on the hot side. To more realistically recreate operating conditions, a methodology is presented to automatically generate distortion screens that can reproduce a two-dimensional distribution of target velocities through additive manufacturing of variable porosity panels. This model, analyzed by means of CFD and validated experimentally, is used to reproduce the typical speed profile present around the exchanger in a real operating circumstance. After defining relevant metrics that allow analyzing the behaviour of the different geometries, it is concluded that aerodynamic and thermal problems are highly coupled in these devices, demonstrating the need for careful design to improve the exchanger's performance. The results show that an improvement of more than 12% in pressure drop and almost 20% in heat exchange can be obtained. In addition, the impact of using the distortion screen has been confirmed, with variations of the order of 10% in both variables. The results also show that it is possible to carry out a preliminary characterization in a reliable way with a 3D printed model, in terms of velocity fields, pressure losses and corrected eigenfrequencies. With the analysis carried out in this thesis, it can be concluded that it is essential to have an experimental installation that reproduces the real operating conditions of an engine to carry out relevant studies of heat exchangers. In addition, the use of appropriate metrics is necessary together with the development of a comprehensive, reliable and robust methodology. The results and methodology presented in this research can have a significant impact both at an academic and industrial level, since they open the door to developing more efficient thermal management systems in preliminary design stages that are more affordable, consume less time and have more flexibility to make changes. / The respondent wishes to acknowledge the financial support received through the Programa de Apoyo para la Investigación y Desarrollo (PAID) of Univer- sitat Politècnica de València under grant PAID-01-20 n◦ 21589. This project has received funding from the Clean Sky 2 Joint Undertak- ing under the European Unions Horizon 2020 research and innovation pro- gramme under grant agreement No 831977 Aerodynamic upgrade of Sur- face Air-Cooled Oil Coolers (SACOC) / Felgueroso Rodríguez, A. (2023). Aerothermal Characterisation of Surface Heat Exchangers for Turbofans [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/195852