Numerous applications in neuroscience research and neural prosthetics, such as retinal prostheses, spinal-cord surface stimulation for prosthetics, electrocorticogram (ECoG) recording for epilepsy detection, etc., involve electrical interaction with soft excitable tissues using a surface stimulation and/or recording approach. These applications require an interface that is able to set up electrical communications with a high throughput between electronics and the excitable tissue and that can dynamically conform to the shape of the soft tissue. Being a compliant and biocompatible material with mechanical impedance close to that of soft tissues, polydimethylsiloxane (PDMS) offers excellent potential as the substrate material for such neural interfaces. However, fabrication of electrical functionalities on PDMS has long been very challenging. This thesis work has successfully overcome many challenges associated with PDMS-based microfabrication and achieved an integrated technology platform for PDMS-based stretchable microelectrode arrays (sMEAs). This platform features a set of technological advances: (1) we have fabricated uniform current density profile microelectrodes as small as 10 microns in diameter; (2) we have patterned high-resolution (feature as small as 10 microns), high-density (pitch as small as 20 microns) thin-film gold interconnects on PDMS substrate; (3) we have developed a multilayer wiring interconnect technology within the PDMS substrate to further boost the achievable integration density of such sMEA; and (4) we have invented a bonding technology---via-bonding---to facilitate high-resolution, high-density integration of the sMEA with integrated circuits (ICs) to form a compact implant. Taken together, this platform provides a high-resolution, high-density integrated system solution for neural and muscular surface interfacing. sMEAs of example designs are evaluated through in vitro and in vivo experimentations on their biocompatibility, surface conformability, and surface recording/stimulation capabilities, with a focus on epimysial (i.e. on the surface of muscle) applications. Finally, as an example medical application, we investigate a prosthesis for unilateral vocal cord paralysis (UVCP) based on simultaneous multichannel epimysial recording and stimulation.

The growth of flexible electronics industry has given rise to light-weight, flexible devices which have a wide range of applications such as wearable electronics, flexible sensors, conformal antennas, bio-medical applications, solar cells etc. Though several techniques exist to fabricate flexible devices, the limiting factors have been durability, cost and complexity of the approach. In this research, the focus has been on developing stretchable (flexible) conductors using a multi-layer structure of metal and conductive rubber. The stretchable conductors developed using this approach do not lose electrical connection when subjected to large strains up to 25%. Also, the conductivity of the conductive rubber has been improved by ~20 times using the multi-layer approach. Furthermore, the multi-layer approach was used to fabricate devices for RF and antenna applications. A flexible micro-stripline was fabricated using the multi-layer approach to study the performance at microwave frequencies up to 5 GHz. It was observed that using an optimal metal and conductive rubber layer structure can help to reduce the loss of the device by 58% and also the device does not get damaged due to bending. In addition to this, an aperture-coupled patch antenna at 3.1 GHz was fabricated using the multi-layer approach to demonstrate reconfigurability. Ideally, the multi-layer patch antennas can be stretched up to 25% which helps to tune the resonance frequency from 3.1 GHz to 2.5 GHz. The multi-layer patch antennas were tested up to ~10% strains to study their radiation properties. It was demonstrated that using an ideal multi-layer structure of metal and conductive rubber layer can help to improve the antenna's peak gain by 3.3 dBi compared to a conductive rubber based antenna.

As visual display technologies move closer to producing true three dimensional displays, pixel technologies need to be ever smaller and more functional to keep pushing the boundaries. Plasmonic metasurfaces have been shown to control the phase, amplitude and/or polarisation of incoming electromagnetic radiation. Nano-fabrication advancements have resulted in the fabrication of the building blocks of such metasurfaces at nano-scale dimensions, allowing the surfaces to interact with visible light, opening up applications in visual displays. As pixel sizes shrink, smaller colour filters will be required. The excitation of plasmonic resonances in metallic nano-structure arrays have resulted in colour filters an order of magnitude smaller than what is currently commercially available. As colour filters, plasmonic metasurfaces offer numerous advantages over pigment-based colour filters used in modern commercial liquid crystal (LC) displays, including environmental, size and longevity factors. Furthermore, exploiting the wavelength and polarisation dependant scattering of nano-structures, optical components, including lenses, waveplates and holograms containing sub-wavelength pixels have been demonstrated in the visible wavelength spectrum. The metasurfaces are able to mould optical wavefronts into arbitrary shapes with sub-wavelength resolution by introducing spatial variations in the optical response of the light scatterers. The applications demonstrated so far are, on the whole, static devices, that is to say their optical properties may not be altered post fabrication. To realise the full potential of plasmonic metasurfaces to visual applications the devices must be made active. By activating structural colour surfaces, not only may pixel densities potentially be increased simply by removing the need for separate red, green and blue filters, but a new class of high definition ultra-thin display devices may be accessible, whilst the dynamic manipulation of the wavelength and polarisation properties of nano-scattering elements would open up the possibilities to create sub-wavelength holographic pixels. This thesis investigates ways to activate static metasurfaces for colour, flat optic, and holographic applications. First, methods of dynamic control of the structural colour of plasmonic nano-hole arrays are investigated. By combining nano-hole arrays with liquid crystals, transmissive electrically tunable LC-nanohole pixels operating across the visible spectrum with un-polarised input light are experimentally demonstrated. An output analyser in combination with a nematic LC layer enables pixel colour to be electronically controlled through an applied voltage across the device, where LC re-orientation leads to tunable mixing of the relative contributions from the plasmonic colour input. Furthermore, exploiting the strong surface anchoring effects between an aluminium surface and LC molecules a twisted nematic LC cell, using a metallic grating as a combined colour filter, electrode and alignment layer, was shown to act a variable amplitude colour filter. The colour of these pixels was improved greatly utilising a grating-insulator-grating structure unique to this work. Second, a new process for fabricating aluminium nano-rod structures embedded in an elastomeric medium, with high spatial accuracy, is presented. The process is used to create nano-rod plasmonic resonator arrays whose optical properties may be altered by mechanical deformation. The pattern transfer process is further utilised to create dynamic optical elements, including nano-rod arrays for colour filters, tunable focal length Fresnel zone plates and photon sieves, and stretchable holograms with dynamic replay fields.

This thesis aims to develop a new type of highly stretchable strain sensor to measure large deformation of a specimen subjected to dynamic loading. The sensor was based on the piezo-resistive response of carbon nanotube(CNT)/polydimethysiloxane (PDMS) composites thin films, some nickel particles were added into the sensor composite to improve the sensor performance. The piezo-resistive response of CNT composite gives high frequency response in strain measurement, while the ultra-soft PDMS matrix provides high flexibility and ductility for large strain measuring large strain (up to 26%) with an excellent linearity and a fast frequency response under quasi-static test, the delay time for high strain rate test is just 30 μs. This stretchable strain sensor is also able to exhibit much higher sensitivities, with a gauge factor of as high as 80, than conventional foil strain gauges.

Executive summary Today, packaging has gained a significant role in the food industry as well as other industries. Paper substrates that have been coated in some ways are typically used to make packaging. The amount and type of pigment used in the formulation determine whether this coating is a pigment coating or a barrier coating. Critical pigment volume concentration (CPVC) is the optimum spot when the pigments are packed as densely as possible, and the binder fills the air gaps. When the amount of pigment in a coating is less than CPVC, a barrier coating is formed, although when the amount of pigment in the coating is greater than CPVC, a pigment coating is formed. Pigment coating adds optical properties to a package, such as improved printability. And chemical protection is primarily provided for water, water vapour, fats, and gases in the case of the barrier coating. Chemical protection against these substances means, for food packaging, that the shelf life of the product will be extended, among other things. The role of packaging in society is expected to grow as barrier coatings on packaging continue to improve. The use of nanoclay in barrier coatings is investigated in this laboratory study. Two latexes are tested with nanoclay, with latex chosen based on its glass transition temperature (Tg). The hypothesis was that a latex with a higher Tg would have more properties like brittleness and orderly structure in its amorphous structure than the other latex. Latex with a lower Tg, on the other hand, would have more elasticity, be more ductile, and have a lower degree of ordered structure in its amorphous structure. Latex with a higher Tg was referred to as Hard latex and was composed of Styrene-butadiene, while latex with a lower Tg was referred to as Soft latex and was composed of Polyolefin dispersion, although it is unorthodox to call it latex. Previous research has found that the addition of Bentonite nanoclay can improve the mechanical and barrier properties of barrier coatings. Bentonite was therefore chosen as the nanoclay for this study due to having a higher aspect ratio, is flaky and can improve desired properties. The coating was applied as a dispersion coating using a lab-scale rod coater. The substrate for this study was BillerudKorsnäs FibreForm with a grammage of 150 g/m2.In order to find the optimum rod for the coating, three different rods were tested during screening test 1. The rods tested were based on the desired coating weight and thickness, a red rod with a wet film thickness of 12 μm was chosen. The nanoclay content of the latex formulation was investigated to determine the optimal level for improved barrier properties. In screening test 2, the concentrations examined were 2/4/8 w/w% nanoclay in each latex, and 0 w/w% to compare the difference with Hard/Soft latex to see if there are any benefits of nanoclay. For both latexes, the addition of 2/4 w/w% nanoclay resulted in more pinholes as well as a poor water vapour transmission rate and permeability. The results of screening test 2 showed that adding 8 w/w% nanoclay to both latexes improved the water vapour transmission rate, water vapour permeability, and pinholes test when compared to the other concentrations of nanoclay. In the water vapour transmission rate and pinholes test, however, 0 percent nanoclay performed similarly 8 w/w% for each latex formulation. The selected formulation for further study was 8 w/w% nanoclay with Hard/Soft latex.  Water vapour was the most important barrier property to investigate since barrier coatings were intended for food packaging. For the intended food packaging, it was sought that the barrier could be stretched with 3.8/6.7/10.4%-stretch and then characterized by water vapour transmission rate to be able to see the differences before and after stretching. Stretching with tensile tester were performed on a barrier coated FibreForm, first in the machine direction (MD), then in cross-direction (CD). Hydroforming with shaped bubbles was used for the second method of stretching with various bubbles. Stretching in MD + CD, and hydroforming bubbles were done according to the desired %-stretching. Characterization of the coating was done by water vapour transmission rate (WVTR) for all coatings, pinholes test for hydroformed coatings, water vapour permeability (WVP) and scanning electron microscopy (SEM) on tensile-stretched coatings. The performance of Soft latex with an 8 w/w% formulation stretched in MD then CD and characterized by water vapour transmission rate was significantly unchanged despite stretching up to 10.4%. This is thought to be because nanoclay, as the literature suggests, has created a better barrier against water vapour. The mean WVTR of 10.4%-stretching in MD then CD was 5.5 g/m2/day, compared to 5.5 g/m2/day for the unstretched barrier.  SEM images of both stretched and non-stretched coatings show that the dispersion of nanoclay is poor, as there are islands of polymer and nanoclay bulk. The poor dispersion of nanoclay in the matrix was due to the lack of polar groups in the backbone of Soft latex (Polyolefin) and also being hydrophobic, as opposed to Bentonite, which is hydrophilic. Despite poor nanoclay dispersion and a stretch of 10.4% in MD + CD, resulting in reduced barrier thickness, WVP improved from 289 g* /m2/day (pre-stress) to 191 g* /m2/day (10.4%-stretch), giving the impression of some reorientation of nanoclay in the polymer matrix. A crack was also visible in SEM images, near the boundary layer between the barrier and the substrate, on an unstretched coating, which is thought to be caused by the difference in the boundary layer and adhesive forces, that has occurred during drying. Cracks are not visible on the stretched barriers, even though it was expected. With increased stretching of hydroforming substrates coated with Soft latex formulation, the performance of water vapour transmission rate was significantly worse. The reason for this is thought to be that the barrier was damaged during hydroforming due to friction during pressing and shaping, as the hydroforming was done on the barrier side. The pinhole test revealed clearly degraded performance with a large number of pinholes. This could indicate that the barrier has been stretched beyond its capacity or has been damaged. There was no correlation found between stretching in tensile tester and hydroforming.  Hard latex with an 8 w/w% formulation stretched in MD then CD and characterized by water vapour transmission rate could be stated to have significantly improved performance despite stretching up to 10.4%. The mean-WVTR of 10.4%-stretching in MD then CD was 11.3 g/m2/day, compared to 16.4 g/m2/day for the unstretched barrier. According to SEM images, the reason for this is that nanoclay was very well dispersed in the matrix and that there has seemingly been a slight reorientation of nanoclay with increased stretch. Furthermore, SEM images show that the thickness was reduced, yet despite this, mean-WVP improved from 1094 g* /m2/day (pre-stress) to 419 g* /m2/day (10.4%-stretch), indicating reorientation of nanoclay and thus improved stretchability.These SEM images show cracks at the boundary layer between the barrier and the substrate for both unstretched and 10.4%-stretched barriers in the Hard latex formulation. The cracks are seemingly stopped by nanoclay in the matrix, according to the stress concentration effect, where the crack moves around nanoclay and not through nanoclay. Hydroforming of barrier coated Hard latex formulation showed a deterioration of water vapour transmission rate with increased stretching. The mean WVTR of hydroforming with 10.4%-stretching was 30.6 g/m2/day. It is not thought that pressing during hydroforming damaged the Hard latex barrier as much, which can be confirmed by the pinholes test. Pinholes test demonstrated good performance and comparable to an unstretched barrier. Because comparisons between the different polymers were impractical, it was not possible to state if the glass transition temperature was important for the improvement seen by stretching in the tensile tester. But it can be argued that Hard latex has a more structured and rigid structure, allowing for a greater degree of reorientation. Soft latex, on the other hand, has less stiffness and thus less reorientation. The result of this study is that when stretching is done in both tensile testing and hydroforming, 8 w/w% nanoclay (bentonite) with Hard latex (styrene-butadiene) can be used advantageously in FibreForm packaging if stretchability is desired while maintaining barrier properties against water vapor. / Sammanfattning Idag har förpackningar fått en betydande roll i matindustrin såväl som andra industrier. Vid bestrykning på förpackningar och papperssubstrat så är det vanligt med pigment- eller barriärbestrykning. Vid pigmentbestrykning så tillförs optiska egenskaper till förpackningen, såsom exempelvis förbättrad tryckbarhet. Vid barriärbestrykning tillförs huvudsakligen kemisk skydd mot exempelvis vatten, vattenånga, fetter eller gaser, och innebär för matförpackningar bland annat att hållbarheten blir längre för livsmedlet. Genom fortsatt utveckling av barriärbestrykningar på förpackningar så förväntas även förpackningens roll i samhället att bli större. I denna laborativa studie undersöks möjligheterna kring töjbara barriärer på papperssubstrat, med fokus på vattenångaresistans.  De formuleringar som togs fram bestod av en latex med låg glasövergångstemperatur (Tg), kallad Soft latex med implementerad nanolera samt en latex med en Tg kallad Hard latex med implementerad nanolera. Soft latex var en Polyolefin dispersion med Tg -30°C, och Hard latex var en Styren-butadien latex med Tg = 0°C. 8 w/w% nanolera var den halt som bedömdes ge förbättringar i de mekaniska samt barriäregenskaper som eftersöktes för de båda latex. För denna studie valdes Bentonit som nanolera, på grund av dess plana samt dess fjälliga (flaky) struktur.  Töjbarheten hos de framtagna barriärformuleringarna testades med töjning i dragprov först i maskin-riktning (MD) och sedan tvär-riktning (CD) samt töjning med hydroforming, med töjning på 3,8/6,7/10,4% för respektive metod. Efter töjning av respektive metod bestämdes överföringshastigheten av vattenångpermabilitet (WVTR) genom barriären. En jämförelse gjordes mellan töjning i dragprov och hydroforming för att få en ökad förståelse kring WVTR-prestationen beroende på metod av töjning.  Soft latex visade en oförändrad vattenångaresistans efter 10,4%-töjning i dragprovaren. Detta tros bero på att nanoleran försvårar vattenångan att genomträngas trots töjning. Vid elektronmikroskop (SEM) kunde det ses att dispersionen av nanolera med Soft latex inte var bra, och därför var inte förbättringarna lika tydliga. Den sämre dispersionen av nanolera i matrisen beror på att Polyolefin saknar polära grupper i dess ryggrad (backbone) samt är väldigt hydrofobt, till skillnad från Bentonit som är hydrofilt. Trots sämre dispersion av nanolera och en töjning på 10,4% i MD + CD, så förbättrades vattenånga permeabiliteten (WVP).För hydroforming var prestationen av Soft latexformuleringen gällande WVTR dåliga, och vid Pinholes test fanns det uppenbara pinholes.  Hard latex visade en tydlig förbättring av WVTR efter 10,4%-töjning i dragprovaren, som tros bero på en omorientering av nanoleran i polymer matrisen vid töjning, vilket kan bekräftas av elektronmikroskop (SEM) där viss omorientering är synlig. Dessutom sågs en tydlig förbättring i WVP trots en lägre barriärtjocklek.För hydroforming var WVTR-värdena liknande till endast Hard latex och 0% nanolera.  Vid töjning var jämförelser beroende på de olika glasövergångstemperaturerna hos polymererna inte möjlig, och därför inte heller möjligt att konstatera ifall glasövergångstemperaturen var viktig för den förbättring som setts trots töjning i dragprovare. Men det kan hävdas att Hard latex har en mer strukturerad och stel struktur, vilket möjliggör en större grad av omorientering. Soft latex däremot, är mindre styvt och mindre ordnat, därav åstadkoms en mindre omorientering.  Resultaten av denna studie är att när stretching görs i både dragprovning och hydroformning, kan 8 w/w% nanoclay (bentonit) med Hard latex (styren-butadien) vara fördelaktig i FibreForm-förpackning om töjbarhet önskas samtidigt som barriäregenskaperna mot vattenånga bibehålls.

Ces travaux de thèse ont porté sur l’élaboration d’électrodes déformables pour la récupération d’énergie houlomotrice. En effet, la conversion de l’énergie mécanique des vagues en électricité est possible via un système entièrement souple et basé sur la technologie des polymères électroactifs (ou EAP). Ces matériaux ont la capacité de se déformer sous stimuli électrique, d’où la nécessité de développer des matériaux conducteurs déformables. Le matériau EAP choisi pour l’étude est un élastomère silicone. La formulation de composites à matrice élastomère silicone chargée en particules conductrices carbonées (graphite, nanofeuillets de graphite et nanotubes de carbone) est ainsi la piste suivie pour composer des électrodes déformables. Deux méthodes de mélange, en voie fondu, ont été explorées. La première utilise un mélangeur planétaire, et la seconde utilise en plus un mélangeur tri-cylindre. L’influence sur les propriétés électriques des composites, de la méthode de mélange, de la nature de la charge conductrice ainsi du taux de charges, a été analysée. Aussi, l’étude de la percolation électrique ainsi que l’étude des mécanismes de conduction mis en jeux dans les différents composites ont été réalisées, et complétées par l’observation de la morphologie en microscopie optique et en microscopie électronique. Le comportement mécanique des composites en traction a également été analysé. Enfin, les propriétés couplées électro-mécaniques des composites les plus prometteurs ont été testées. Les mesures permettent de proposer une formulation à base de nanotubes de carbone comme électrode déformable. / This PhD work presents the development of stretchable electrodes for wave energy harvesting. Indeed, it is possible to convert the mechanical energy of the waves into electricity thanks to a flexible system based on electroactive polymer (EAP) technology. As EAPs have the ability to deform under electrical stimuli, deformable conductive materials are needed. In this study, the chosen EAP is a silicone elastomer. Composites formulated with silicone elastomer matrix filled with carbonaceous conductive particles (graphite, graphite nanoplatelets and carbon nanotubes) were thus developed. Two mixing methods, by melt compounding, have been explored. The first uses a planetary mixer, and the second uses a three roll-mill. The influence of the mixing method, the nature of the fillers and the filler rate on the electrical properties of the composites has been analyzed. The morphology, as well as the percolation and the conduction mechanisms have been studied. The tensile properties of the composites were also analyzed. Finally, the electromechanical coupled properties of the most promising composites were tested, allowing us to propose a formulation as a stretchable electrode.

<p>In this dissertation, we show three approaches towards selective vagus nerve stimulation (VNS). First, we investigated VNS using microelectrode with circle and Vicsek fractal shape. Our rat study shows that fractal microelectrode can activate C-fibers in cervical vagus nerve with higher energy efficiency compared to circle microelectrode. Secondly, we developed stretchable and adhesive cuff device for a compliant neural interface for a long-term stability. We designed Y-shaped kirigami thin-film device for stretchable neural interface and applied a tissue-adhesive hydrogel to enable tough adhesion of the cuff electrode, which can be potentially used to fix the position of microelectrode for a reliable selective stimulation with minimal mechanical mismatch. Lastly, we developed a microchannel electrode array device to potentially measure high-quality of single fiber action potential (SFAP) from the abdominal vagal trunk of rat to explore natural patterns selective organ activities which can be used for a fine-tuned selective VNS. Our results show the potential of measuring C-fiber activities evoked by cervical VNS.</p>

During past years, organic-based electronic devices revealed high promise to supplement the ubiquitous silicon-based electronic devices and enable new fields of applications. At the center of this development is the considerable progress regarding π-conjugated polymer semiconductors (PSCs): Due to their processability from solution, light-weight, as well as low-cost, PSCs are now evolving towards production-scale of new technologies, e.g., in organic solar cells (OSCs), organic field-effect transistors (OFETs), and organic light emitting diodes (OLEDs). Especially OFETs are of fundamental importance, as they constitute the switching units in all logic circuits and display technologies. However, the future world is expected to be full with smart electronics and communication devices integrated in clothes, tools and even interacting with the human body, e.g., as on-skin wearable sensors. For this the electrically-active material, just as a human tissue, requires to combine several properties in addition to being charge conducting: They need to show (i) mechanical softness, (ii) capacity to repair, (iii) multimodal sensitivity, as well as (iv) biodegradability. Here, PSCs still face challenges as they are brittle and break upon applying a mechanical stress. When trying to address this issue, the existing knowledge on mechanical properties of well-established polymeric plastics, e.g., polystyrene, cannot be directly applied for several reasons, e.g., (i) the bulkiness of monomers (including long side-chains), (ii) the rigid π-conjugated backbone, (iii) the low degree of polymerization, (iv) the small quantities in which PSCs are available, etc. Moreover, these kinds of materials should not only be mechanically compliant and stretchable, but furthermore retain their charge mobility upon stretching, and withstand numerous of mechanical stretching cycles. Considering this complex problem, researchers have been developing and investigating several approaches to combine good electrical properties and mechanical compliance within one material. These approaches include (i) stress-accommodating engineering, (ii) blending of PSCs into elastic matrix, as well as (iii) molecular engineering approach. The latter seeks to interlink mechanical and electrical properties on the molecular level, i.e., synthesize polymers that are charge conducting and stretchable. Different strategies were tested, from the modification of side chains, to the introduction of conjugation breakings spacers into the backbone. Selected works sought to incorporate stretchability and conductivity by utilizing block copolymers, i.e., covalently linking a conjugated and a non-conjugated polymer chain, resulting in a phase separation of both constituents and preserving their respective properties. The ultimate goal of this work is to achieve an intrinsically stretchable and electrically high-performing PSC via the block copolymer approach. This is done by connecting organosilicone, namely the polydimethylsiloxane (PDMS) elastomer – possessing outstanding mechanical properties, as well as good environmental and air stability – with a conjugated diketopyrrolopyrrole (DPP)-based donor-acceptor copolymer. The final obtained structure of this polymer is a tri-block copolymer (TBC) consisting of an inner DPP-based polymer block and two outer soft PDMS polymer blocks. The content of PDMS block can be controlled and be very high (up to 67 wt%), and easy processing, e.g., via shear coating, is possible. Relatively high charge carrier mobilities – in the same range as the reference DPP-based copolymer (i.e., without outer PDMS blocks) – are retained, and the block copolymers withstands numerous stretching cycles (up to 1500 cycles) without losing electrical functionality. Finally, one of the block copolymers was successfully incorporated into a biosensor for COVID-19 antibodies and antigens detection. Overall, the findings of this work show that the block copolymer is a highly versatile approach to obtain functional and stretchable semiconductors with high charge carrier mobilities. Block copolymers consisting of a high-performing donor-acceptor PSC and a biocompatible elastomer could contribute towards one of the long-term goals of organic electronics – the realization of mechanically compliant materials for applications in stretchable electronics (e.g., wearable sensors, electronic skin, etc.).

Electronic devices define our everyday lives. They are often large, rigid, and brittle. Modern medical science has come so far as to start using miniature electronic devices to monitor many types of diseases. Especially, neurological disorders pose obstacles hard to overcome when treating them but it also motivates finding methods that allow for continuous monitoring. Implementing a small electronic device inside the human body adds requirements on the device to be stretchable, biocompatible, and more. Not only is the device limited by these factors, but also, current fabrication methods are not efficient for creating nanoscale versions for these types of devices. patterninglaser ablation is a growing field for cutting out and pattern nano-materialistic devices with high precision and good repeatability. This project is focused on using a laser engraving tool from metaquip on different substrates. This project is focused on the development of methods for laser fabrication of soft neural electrodes. The requiered steps are the alignment of samples to assure good precision when engraving it with the laser engraving tool, that also will be called “laserpatterner”, finding good parameters for cutting out devices and pattern conductors for said devices. On top of that, a linear force stretching will be used to characterize samples that were cut, in the form of strips, using the laserpatterner. The stretching behavior of strips consisting of the elastomer polydimethylsiloxane, which in turn will be the insulator for silver nanowires, is examined in the stretching setup. Parameter optimization is relevant in all experiments done in this project and lay the foundations for cutting and patterning silver nanowires devices. All factors included will eventually lead to a good method for fabricating soft neural electrode devices and this project is stepping stone towards that goal. / <p>Examensarbetet är utfört vid Institutionen för teknik och naturvetenskap (ITN) vid Tekniska fakulteten, Linköpings universitet</p>

Flexible and stretchable wearable biomedical devices provide a platform for continues long-term monitoring of biological signals during neutral body movements thus enabling early intervention and diagnostics of various diseases. This thesis evaluates novel flexible and stretchable bio interfacing medical devices based on microneedle patches and split ring resonator for healthcare diagnostics. Flexible and stretchable microneedle patches were realized by integrating a soft polymer substrate with sharp stainless steel microneedles. This was realized using a magnetic assembly technique. Investigations have shown that the flexible microneedle patch can provide conformal and reliable contact with wrinkles and deformations of the skin. In addition, transdermal monitoring of potassium ions using the proposed flexible microneedle patch have been demonstrated by coating the microneedles with a potassium sensing membrane. Ex-vivo test on the microneedle potassium sensor performed on chicken and porcine skin was able to detect change in potassium concentration in the skin. Furthermore, a novel flexible bio-interface spilt ring resonator (SRR) for the monitoring of intera cranial pressure (ICP) is demonstrated. The sensor was fabricated by depositing a 500 nm gold film on a thermoset thiolene epoxy polymer substrate. The flexible sensor was able to clearly detect the pressure variation that might be an indication of increased ICP in the skull. The proposed methodology of heterogeneous integration of hard materials on a soft and flexible substrate demonstrates a first proof of concept of flexible wearable bio-interfacing devices with vastly different material properties with the potential for continuous and real-time health monitoring. / <p>QC 20190306</p>