Made available in DSpace on 2014-12-17T14:07:18Z (GMT). No. of bitstreams: 1 LaureniceMP_DISSERT.pdf: 7523564 bytes, checksum: 3bb1b06da6a21522b0974a84935760a3 (MD5) Previous issue date: 2014-12-28 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior / The development of new materials to fill the demand of technological advances is a challenge for many researchers around the world. Strategies such as making blends and composites are promising alternatives to produce materials with different properties from those found in conventional polymers. The objective of this study is to evaluate the effect of adding the copolymer poly(ethylene methyl acrylate) (EMA) and cotton linter fibers (LB) on the properties of recycled poly(ethylene terephthalate) (PETrec) by the development of PETrec/EMA blend and PETrec/EMA/LB blend composite. In order to improve the properties of these materials were added as compatibilizers: Ethylene - methyl acrylate - glycidyl methacrylate terpolymer (EMA-GMA) and maleic anhydride grafted polyethylene (PE-g-MA). The samples were produced using a single screw extruder and then injection molded. The obtained materials were characterized by thermogravimetry (TG), melt flow index (MFI) mensurements, torque rheometry, pycnometry to determinate the density, tensile testing and scanning electron microscopy (SEM). The rheological results showed that the addition of the EMA copolymer increased the viscosity of the blend and LB reduces the viscosity of the blend composite. SEM analysis of the binary blend showed poor interfacial adhesion between the PETrec matrix and the EMA dispersed phase, as well as the blend composite of PETrec/EMA/LB also observed low adhesion with the LB fiber. The tensile tests showed that the increase of EMA percentage decreased the tensile strength and the Young s modulus, also lower EMA percentage samples had increased the elongation at break. The blend composite showed an increase in the tensile strength and in the Young`s modulus, and a decrease in the elongation at break. The blend formulations with lower EMA percentages showed better mechanical properties that agree with the particle size analysis which showed that these formulations presented a smaller diameter of the dispersed phase. The blend composite mechanical tests showed that this material is stronger and stiffer than the blend PETrec/EMA, whose properties have been reduced due to the presence of EMA rubbery phase. The use of EMA-GMA was effective in reducing the particle size of the EMA dispersed phase in the PETrec/EMA blend and PE-g-MA showed evidences of reaction with LB and physical mixture with the EMA / O desenvolvimento de novos materiais para atender as necessidades dos avan?os tecnol?gicos ? um desafio enfrentado por pesquisadores de todo o mundo. No que diz respeito aos materiais polim?ricos, estrat?gias como a confec??o de blendas e comp?sitos s?o alternativas promissoras para atender a demanda por materiais com propriedades diferentes das encontradas nos pol?meros convencionais. O objetivo deste trabalho ? avaliar o efeito da adi??o do copol?mero poli(etileno-acrilato de metila) (EMA) e da fibra de linter de algod?o (LB) nas propriedades do poli(tereftalato de etileno) reciclado (PETrec). Para isto, foram desenvolvidos a blenda PETrec/EMA e o comp?sito da blenda PETrec/EMA/LB. Com o intuito de melhorar as propriedades destes materiais foram adicionados agentes compatibilizantes: terpol?mero etileno-acrilato de metila-metacrilato de glicidila (EMA-GMA) e o polietileno enxertado com anidrido mal?ico (PE-g-MA). As misturas foram produzidas por meio de uma extrusora monorosca e, em seguida, moldados por inje??o. As caracteriza??es realizadas foram termogravimetria (TG), medida de ?ndice de fluidez (MFI), reometria de torque, determina??o da densidade por picnometria, ensaio de tra??o uniaxial e microscopia eletr?nica de varredura (MEV). Os resultados reol?gicos mostraram que a adi??o do copol?mero EMA aumentou a viscosidade da mistura e o LB reduziu a viscosidade da blenda PETrec/EMA. A an?lise por MEV da blenda bin?ria mostrou baixa ades?o interfacial entre a matriz de PETrec e a fase dispersa de EMA, assim como no comp?sito da blenda PETrec/EMA/LB, tamb?m observou-se uma baixa ades?o com a fibra de LB. Os ensaios de tra??o mostraram que o aumento da porcentagem de EMA diminuiu a resist?ncia m?xima e o m?dulo de elasticidade, e, para as formula??es com menor porcentagem de EMA verificou-se um aumento do alongamento na ruptura. O comp?sito da blenda apresentou um aumento na resist?ncia m?xima e no m?dulo de elasticidade, e uma redu??o no alongamento de ruptura. As formula??es da blenda com menores porcentagens de EMA apresentaram propriedades mec?nicas melhores, que corrobora com as an?lises de tamanho de part?cula que mostraram que estas formula??es apresentaram menor di?metro m?dio de fase dispersa. Os resultados de ensaios mec?nicos do comp?sito da blenda mostraram que essa mistura resultou em um material com maior resist?ncia mec?nica e rigidez do que a blenda PETrec/EMA, cujas propriedades foram reduzidas em fun??o da fase borrachosa EMA. O uso do EMA-GMA foi eficiente na redu??o do tamanho de part?culas da fase dispersa do EMA na blenda PETrec/EMA e o PE-g-MA apresentou ind?cio de rea??o com o LB e mistura f?sica com o EMA

Submitted by Emanuel Varela Cardoso (emanuel.varela@ufcg.edu.br) on 2018-06-05T00:24:48Z No. of bitstreams: 1 JOSÉ DE ARIMATÉIA ALMEIDA E SILVA – TESE (PPGEP) 2015.pdf: 6946608 bytes, checksum: 04efbba58513fb4cbcc2225d2ade0888 (MD5) / Made available in DSpace on 2018-06-05T00:24:48Z (GMT). No. of bitstreams: 1 JOSÉ DE ARIMATÉIA ALMEIDA E SILVA – TESE (PPGEP) 2015.pdf: 6946608 bytes, checksum: 04efbba58513fb4cbcc2225d2ade0888 (MD5) Previous issue date: 2015-06-26 / Capes / A adição do resíduo de Politereftalato de Etileno (PET) em Cimentos Asfálticos de Petróleo (CAP), triturados em partículas cujo diâmetro está entre 0,6 e 0,074 mm, pode ser uma alternativa técnica viável para melhorar as propriedades mecânicas e reológicas das misturas asfálticas. Esta adição tem como finalidade proporcionar uma menor susceptibilidade das misturas asfálticas a fadiga e, conseqüentemente aumentar a vida útil de revestimentos asfálticos em regiões com clima tropical e a temperaturas elevadas. Este trabalho tem como objetivo principal a incorporação de um aditivo no Cimento Asfáltico de Petróleo. A adição de PET foi realizada em proporções de 4%, 5% e 6% relativas ao peso do teor de CAP ótimo e mensuradas as propriedades volumétricas e mecânicas. Além disso foram realizados análises físicas e reológicas do CAP puro e modificado. De acordo com os resultados obtidos nesta pesquisa pode -se inferir que o PET micronizado pós consumo corresponde a um polímero melhorador das propriedades reológicas do CAP 50/70, em termos de rigidez, proporcionado a mistura asfáltica um incremento no comportamento mecânico a luz dos ensaios de Resistência à Tração por Compressão Diametral, Módulo de Resiliência, Resistência por Umidade Induzida, Flow Number e Ruptura por Fadiga. É possível aceitar que “o resíduo do PET micronizado, no teor de 5% pode ser utilizado como agente modificador do CAP e, que o mesmo e capaz de promover ganhos nas Propriedades Mecânicas de Revestimentos Asfálticos. / The addition of polyethylene terephthalate (PET) waste in binder, crushed into particles whose diameter is between 0.074 and 0.6 mm, may be a viable alternative technique to improve the mechanical and rheological properties of asphalt mixtures . This addition is intended to provide a lower susceptibility of fatigue in asphalt mixtures and consequently improve the durability of asphalt mixtures in regions with tropical climate and high temperatures. This work has the objective the incorporation of an additive in binder. It was add in proportions of 4% 5% and 6% relative to the weight of the optimum binder content and it was measured volumetric and mechanical properties of asphalt mixtures. Also performed were physical and rheological analysis of pure and modified binder. According to the results obtained in this study can be inferred that the micronized PET improve the performance of binder 50/70. The addition of PET provided an increase in the mechanical behavior in the Indirect Tensile Strength, Resilient Modulus, Moisture susceptibility, Flow Number and Fatigue life. It is possible to accept that the use of 5% micronized PET waste may be used as modifying agent of binder, and that it improve mechanical properties of asphalt mixtures.

Made available in DSpace on 2016-06-02T20:36:56Z (GMT). No. of bitstreams: 1 6787.pdf: 6528368 bytes, checksum: 59d1763870e2de400270ed05b0ac6675 (MD5) Previous issue date: 2015-03-25 / Universidade Federal de Sao Carlos / Polyelectrolytes complexes (PECs) are defined as materials formed by combining oppositely charged polyelectrolytes together via ionic interaction. PECs have some unique physical properties such as non-solubility in common organic solvents, high surface hydrophilicity, tunable surface charge, and stable structures. A new type of PEC based on chitosan (CS) and sulfonate poly(ethylene terephthalate) (SPET) were synthesized in two different media, buffer solution and salt solution acidified with acetic acid. Fourier transform infrared spectroscopy (FTIR), zeta potencial, X-ray diffraction, thermal gravity analysis and differential scanning calorimetry were used to characterize the chemical structure, particle charge, crystallinity and thermal stability. To assess how the internal structure of the PEC and the subsequent membrane formation can affect water and salts transport capacity of microporous polycarbonate membrane, PECs solutions were spread via casting in commercial membranes with pore size of 5 μm. These membranes were characterized by Scanning Electron Microscopy (SEM), Water Vapor Flux, Resistance to Ion Migration and Membrane Potential. FTIR results indicated the electrostatic interaction of polyelectrolyte to form the polyelectrolyte complex. From the results of zeta potential it was found that the surfaces of CS/SPET nanoparticles have positive charges of about 25 to 44 mV. TGA curves showed that the PECs were more stable than their polyelectrolytes. The deposition of the PEC on the membranes was confirmed by SEM images and the increase of water vapor flux of membranes indicated that the presence of the complex significantly alter the hydrophilic profile of the polycarbonate matrix. The microfiltration of Saccharomyces cerevisiae cells demonstrated that membranes modified with PECs retained more of these organisms than the commercial membrane without modification. / Complexos de polieletrólitos (PECs) são definidos como materiais formados pela combinação de polieletrólitos de cargas opostas via interação eletrostática. PECs possuem algumas propriedades únicas como não solubilidade em solventes comuns, alta hidrofilicidade, superfícies modificáveis e estruturas estáveis. Um novo tipo de PEC baseado em quitosana (QT) e poli(tereftalato de etileno) sulfonado (PET-S) foi sintetizado em dois meios diferentes, uma solução tampão ácida e uma solução salina acidificada. Espectroscopia de infravermelho com transformada de Fourier (FTIR), potencial zeta, difração de raios X, análise termogravimétrica e calorimetria diferencial exploratória foram usados para caracterizar a estrutura química, carga da partícula, cristalinidade e estabilidade térmica. Para avaliar como a estrutura interna do PEC e a subsequente formação de membrana pode afetar o transporte de água e sais em membranas de policarbonato microporosas, soluções de PEC foram espalhadas via casting em membranas comerciais com tamanho de poro de 5 μm. As membranas foram caracterizadas utilizando microscopia eletrônica de varredura, transporte de vapor de água, resistência a migração iônica e potencial de membrana. Resultados de FTIR comprovaram a interação eletrostática entre os polieletrólitos e consequentemente a formação dos PECs. O potencial zeta dos PECs apontou que eles apresentam superfícies positivas que variam de 25 a 44 mV. O TGA demonstrou que os PECs são termicamente mais estáveis do que seus polieletrólitos precursores. A deposição dos PECs sobre as membranas foi confirmada pelo MEV e o aumento do fluxo de vapor de água indicou que a presença dos PECs altera significativamente o caráter hidrofílico do policarbonato. A microfiltração de células Saccharomyces cerevisiae mostrou que as membranas modificadas com PECs reteram mais desses organismos do que a membrana comercial sem modificação.

Polyethylene terephthalate (PET) is the most used fibre in the textile industry. PET is also used in other products, e.g. soft-drink bottles and food packaging. Approximately 60% of the globally produced PET is intended for production of textile fibres and the demand for polyester fibres have steadily increased over the last decade. Yet, most of the recycled PET fibres are produced from discarded bottles and not discarded textiles even though the generation of textile waste is increasing year by year. The importance of finding efficient recycling routes for discarded PET textiles is obvious. In thermo-mechanical recycling the thermoplastic characteristic of PET is utilized to re-melt and re-form PET waste into new valuable products. Today, this is used for bottle-to-fibre recycling but not for fibre-to-fibre recycling. The main research question asked in this Master thesis is if the process of exhaust dyeing compromise the possibility to recycle PET textiles through remelt spinning. It is believed that PET degradation through hydrolysis may occur during dyeing. The degradation behaviour of PET has been widely studied. However, degradation during exhaust dyeing has not been investigated.   The process parameters temperature, time and number of dyeing cycles have been investigated. Also, possible effects of different auxiliary chemicals have been studied. Dyeing and characterisation of two PET fabrics with filaments of different titer was performed in order to investigate if the filament titer is also a parameter to consider.   Tensile testing and surface characterisation through demand absorbency test showed that the filament titer seems to affect how the tensile and moisture related properties change due to dyeing. Differential scanning calorimetry showed that the crystallisation rate is affected by the dyeing process. This can be an effect of formation of shorter PET chains during dyeing. The auxiliary chemicals have been shown to be the most critical factor in changes of the crystallisation behaviour. Fourier-Transform infrared spectroscopy indicated that chain scission has occurred during dyeing.   The results have shown that the exhaust dyeing process causes changes in tensile properties, moisture related properties, degree of crystallinity as well as crystallisation behaviour. DSC and FTIR results indicate chain scission. Based on the results it cannot be concluded if the changes are large enough to compromise the possibility to recycle PET textiles thermo-mechanically. Further research is required in order to correlate the observed changes with possible problems in thermomechanical recycling of dyed PET textiles.

Submitted by Viviane Lima da Cunha (viviane@biblioteca.ufpb.br) on 2017-07-18T12:00:27Z No. of bitstreams: 1 arquivototal.pdf: 3670112 bytes, checksum: d762a13cb07012ebb6bb3db0a6e3d4d6 (MD5) / Made available in DSpace on 2017-07-18T12:00:27Z (GMT). No. of bitstreams: 1 arquivototal.pdf: 3670112 bytes, checksum: d762a13cb07012ebb6bb3db0a6e3d4d6 (MD5) Previous issue date: 2016-09-30 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - CAPES / The accumulated water on pavement surfaces is one of the factors responsible for the occurrence of traffic accidents, as it reduces the tire-pavement interface friction. The use of porous asphalt mixtures can increase road safety because it increases the adherence between a vehicle's tires and the pavement, especially in a wet highway, owing to its high drainage capacity. Accordingly, this research had the purpose of analyzing the use of polyethylene terephthalate (PET) waste as an alternative of additives to porous asphalt mixtures. The work method consisted of materials characterization, determination of the optimum binder content, production of three kinds of asphalt mixtures (conventional, with the addition of PET, and with polymer asphalt) and the performance of draindown tests, moisture susceptibility, resilient modulus, flow number, fatigue test, permeability to the asphalt mixtures, in their respective optimum binder contents. The PET was added to the mixtures by a dry process in the proportions of: 0; 0,33; 0,5; 0,75 e 1% regarding to the weight of the aggregates. The asphalt mixtures with polymer asphalt were taken as reference. Considering the mixtures design, additions of 0,75% PET up carried out the lowest optimum binder content. Besides that, the addition of PET contributed for a binder draindown inhibition and improved the mixtures performance regarding to moisture susceptibility. The PET additivated mixtures presented an increasing in the resilient modulus and a tendency of a longer fatigue life at low tension levels and high number of load applications. However, the mixtures are susceptible to rutting, even though presenting stiffening. Concerning to permeability, the execution of only one test became inconclusive. Although, it was verified that PET can present viability of being used as additive porous asphalt mixtures. / A água acumulada sobre a superfície do pavimento é uma das responsáveis pela ocorrência de acidentes em rodovias, por reduzir o atrito na interface pneu-pavimento. A adoção de misturas asfálticas porosas pode aumentar a segurança viária, pois seu uso favorece a aderência entre os pneus dos veículos e o pavimento, especialmente em pista molhada, tendo em vista a sua alta capacidade de drenagem. Diante disso, esta pesquisa objetivou analisar o uso de resíduos de politereftalato de etileno (PET) como aditivo para misturas asfálticas porosas. O método de trabalho consistiu na realização de ensaios de caracterização dos materiais utilizados, determinação do teor de projeto de ligante asfáltico, confecção de três tipos de misturas asfálticas (convencional, com adição de PET e com asfalto polímero) e realização de ensaios de escorrimento, dano por umidade induzida, módulo de resiliência, deformação permanente, vida de fadiga e permeabilidade para as misturas asfálticas, em seus respectivos teores de projeto de ligante asfáltico. A adição de PET nas misturas foi realizada via processo seco nas proporções 0,00; 0,33; 0,50; 0,75 e 1,00% em relação ao peso dos agregados. As misturas asfálticas com asfalto modificado por polímero foram tomadas como referência, tendo em vista a preferência do uso desse tipo de ligante em misturas porosas. Em termos de dosagem, adições de PET em até 0,75% resultaram na redução do teor de projeto de ligante asfáltico. Além disso, o PET contribuiu para a inibição do escorrimento do ligante e favoreceu o desempenho das misturas em relação ao dano por umidade induzida. As misturas aditivadas com PET apresentaram um aumento no módulo de resiliência e uma tendência de maior vida de fadiga para baixos níveis de tensões e elevadas repetições de carga. Porém, mostraram-se suscetíveis à deformação permanente, mesmo tendo apresentado um maior enrijecimento. Quanto a permeabilidade, é necessário a realização de mais ensaios de modo a garantir uma melhor confiabilidade nos resultados. De todo modo, pôde-se verificar que o PET pode apresentar viabilidade de ser utilizado como aditivos em misturas asfálticas porosas.

Made available in DSpace on 2015-05-14T13:21:19Z (GMT). No. of bitstreams: 1 ArquivoTotal.pdf: 4834263 bytes, checksum: 9a0661df73e9955af44f0e37d15bf261 (MD5) Previous issue date: 2012-09-17 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - CAPES / The heterogeneous catalysis is a promising alternative to solve the environmental problems found in homogeneous catalysis, because it allows the continuous use of the catalyst until its deactivation and minimizes the generation of effluents. Thus, this work aims to synthesize, optimize and evaluate the activity of heterogeneous catalysts, using PET bottles as a starting material in the synthesis of the active phase and SiO2 as catalyst support for the transesterification reaction of soybean oil. The the catalysts were obtained by a impregnating reaction using methanol. The active phase, the catalysts and catalyst support were characterized by X-ray diffraction (XRD), infrared (IR), Raman spectroscopy, scanning electron microscopy (SEM) and EDS, thermal analysis (TG) and measurement surface area (BET). The biodiesels has been synthesized using a molar ratio of 1:9 (soybean oil: methanol), 0,1 g of active phase as catalyst (room temperature) and 1,2 g of the catalysts synthesized at 75 °C, where its kinematic viscosities were measurements. All catalysts were effective in the synthesis of biodiesel because the viscosity reduction of soybean oil used was very significant, indicating that may have occurred the transesterification process, among all biodiesels synthesized the catalyst that stood out was the 30%-K2CO3/70% SiO2, which was obtained greater viscosity reduction at a lower reaction time. The quality tests were made for 1h Bio-30%, which proved be inside the parameters established by the Agência Nacional de Patróleo (ANP). The experiment reuse of the catalyst used in the synthesis of Bio-1h 30%, showed that the catalytic activity is reduced due to possible leaching phenomenon, then preliminary studies have been proposed to study the possible leaching of the active phase. / A catálise heterogênea é uma alternativa promissora para resolver os problemas ambientais encontrados na catálise homogênea, pois permite o uso continuo do catalisador até sua desativação e minimiza a geração de efluentes. Neste sentido, este trabalho visa em sintetizar, otimizar e avaliar a atividade de catalisadores heterogêneos, utilizando a garrafa PET pós-consumo como matéria prima na síntese da fase ativa e SiO2 como suporte catalítico para a reação de transesterificação com óleo de soja. Os catalisadores foram obtidos pela o método de impregnação utilizando o metanol como solvente. A fase ativa, os catalisadores e o suporte catalítico foram caracterizados por difração de raios-X (DRX), espectroscopia na região do infravermelho (IV), espectroscopia Raman, microscopia eletrônica de varredura (MEV) e EDS, análise térmica (TG), e medida de área superficial (BET). Os biodieseis foram sintetizados utilizando uma razão molar de 1:9 (óleo de soja: metanol), 0,1 g da fase ativa como catalisador a temperatura ambiente e 1,2 g dos catalisadores sintetizados a 75 °C, onde suas viscosidades cinemáticas foram medidas. Todos os catalisadores foram efetivos na síntese do biodiesel, pois promoveu a redução de viscosidade do óleo de soja utilizado, no qual mostrou um indicativo que a reação de transesterificação ocorreu, dentre todos os biodieseis sintetizados o catalisador que mais se destacou foi o 30%-K2CO3/70%-SiO2, onde obteve-se a maior redução de viscosidade com um menor tempo reacional. Os testes de qualidade foram feitos para o Bio 1h-30%, o qual mostrou estar dentro dos parâmetros estabelecidos pela Agência Nacional de Petróleo (ANP). O experimento de reuso do catalisador utilizado na síntese do Bio 1h-30%, mostrou que a atividade catalítica é reduzida devido ao possível fenômeno de lixiviação, então estudos preliminares foram propostos para estudar a possível lixiviação da fase ativa.

In current enterprises, simulations are being utilized to lessen the cost of product advancement.  Along this line, there is an awesome enthusiasm for enhancing precision and accuracy of simulations. For an accurate and reliable simulation, it is essential to use an accurate material model and provide it with accurate material information. In exhibit industries, orthotropic materials are being simulated utilizing isotropic material model, as orthotropic material model requires more material data which is not promptly accessible. This proposal intends to test and identify orthotropic materials and simulate them using orthotropic material model in ABAQUS. Materials utilized as a part of this proposal are Aluminium, LDPE, PET. Required material data was gotten by performing Uni-directional tensile tests, DIC, and an algorithm we developed in light of Inverses method. To get highly accurate material data from DIC, a few kinds of patterns were examined, and a superior pattern was resolved for camera configuration being utilized.

Organic electrode materials represent an intriguing alternative to their inorganic counterparts due to their sustainable and environmental-friendly properties. Their plastic character allows for the realization of light-weight, versatile and disposable devices for energy storage. Conducting redox polymers (CRPs) are one type of the organic electrode materials involved, which consist of a π-conjugated polymer backbone and covalently attached redox units, the so-called pendant. The polymer backbone can provide conductivity while it is oxidized or reduced (i. e., p- or n-doped) and the concurrent redox chemistry of the pendant provides charge capacity. The combination of these two components enables CRPs to provide both high charge capacity and high power capability. This dyad polymeric framework provides a solution to the two main problems associated with organic electrode materials based on small molecules: the dissolution of the active material in the electrolyte, and the sluggish charge transport within the material. This thesis introduces a general synthetic strategy to obtain the monomeric CRPs building blocks, followed by electrochemical polymerization to afford the active CRPs material. The choice of pendant and of polymer backbone depends on the potential match between these two components, i.e. the redox reaction of the pendant and the doping of backbone occurring within the same potential region. In the thesis, terephthalate and polythiophene were selected as the pendant and polymer backbone respectively, to get access to low potential CRPs. It was found that the presence of a non-conjugated linker between polymer backbone and pendant is essential for the polymerizability of the monomers as well as for the preservation of individual redox activities. The resulting CRPs exhibited fast charge transport within the polymer film and low activation barriers for charge propagation. These low potential CRPs were designed as the anode materials for energy storage applications. The combination of redox active pendant as charge carrier and a conductive polymer backbone reveals new insights into the requirements of organic matter based electrical energy storage materials.

Les isolateurs diélectriques utilisés dans les disjoncteurs haute tension développés par Areva, sont fabriqués à partir du PET (polyéthylène téréphtalate). Ce polymère semi-cristallin a remplacé, depuis quelques années, les résines époxy. Il a été choisi pour ses propriétés mécaniques et diélectriques, mais surtout pour sa recyclabilité. Le souci dans cette application, concerne l’évolution dans le temps de ses caractéristiques sachant les contraintes d’application. En effet, dans les conditions de travail, les isolateurs maintiennent des conducteurs électriques. Les pertes thermiques affectent certaines zones pouvant atteindre, voire dépasser, la température de transition vitreuse du matériau [70-80°C]. Par conséquence, les pièces isolatrices subissent un phénomène de vieillissement qui nécessite un suivi dans le temps afin d’étudier l’évolution de leur caractéristiques Dans ce contexte, nous avons étudié le vieillissement thermique du PET. Ainsi des échantillons ont été mis dans des étuves sous vide, chacune réglée à une température : 60, 80, 115 et 125°C pendant différentes durées (jusqu’à 12 mois de vieillissement), puis retirés et testés au fur et à mesure du vieillissement. Différentes techniques ont été employées pour analyser les propriétés du semi-cristallin en question, i.e. l’étude calorimétrique différentielle (DSC), les diffractions aux rayons X aux grands et petits angles (WAXS/SAXS). L’analyse thermomécanique (DMA) et finalement les essais de traction.Les résultats de DSC révèlent une augmentation du taux de cristallinité. Les analyses thermomécaniques ont montré une faible augmentation du module de Young qui pourrait être le résultat d’une évolution de la cristallisation. Les températures de fusion sont restées quasiment stables, par contre une augmentation des températures de transition vitreuse a été remarquée. Les analyses des spectres de diffraction aux rayons X aux grands angles, ont confirmé la croissance du taux de cristallinité. En outre les longues périodes calculées, diminuent. Nous avons ainsi vérifié l’apparition de cristallites dans phase amorphe. Par ailleurs un comportement de fragilité continue en fonction du temps et de la température du vieillissement, a été constaté. Les observations au MEB ont révélé la présence d’une importante quantité de particules supposées être des agents nucléants (talc, SiO2, MgO…) / For insulating application, AREVA has chosen PET (polyethylene terephthalate) to substitute the epoxy resin as material for insulators in High Voltage Gas Insulated Substation. The main problem of this application is the fact that in operating conditions, the temperature of the PET plates would reach even exceed its glass transition [70°C-80°C]. The material undergoes aging phenomena which affect the temperature-dependent properties. The current investigation aims at observing and analyzing the gradual evolution of the mechanical, morphological and dielectric properties during thermal aging. To reach this goal, semi crystalline PET samples have been aged under vacuum at different temperatures i.e. 60°C, 80°C, 115°C and 125°C for various periods of time (until 12 months). The characterizations have been performed using several techniques: Differential scanning calorimetric (DSC), wide and small angle X-ray scattering (WAXS/SAXS), thermo-mechanical analysis (DMA), tensile test and morphological observation.The DSC measurements show that the crystallinity ratio increases with temperature and time of aging. The glass transition has increased. However no significant changes have been seen on the melting temperature. The DMA results agree with the DSC measurement in so far as it has revealed an expected increase of the Young modulus for all the samples studied. Significant differences have been observed using X-ray scattering: while the crystallinity ratio did increase, the long period has decreased specially for the case of aging at 115 and 125°C. The DMA measurements showed an almost stable glass transition around 80°C but an increase for samples aged at 125°C. When the samples have been subjected to the tensile test, a significant brittleness rise has been noticed. In addition, the SEM has revealed the presence of important amount of nucleant agent (talc, SiO2, MgO …)

El Poli-Tereftalato de Etileno y caucho en desuso, se encuentran toneles en los vertederos, en los ríos y océanos, su tasa de degradación es lenta, en la actualidad se han convertido parte de la crisis ecológica. Es vital un cambio de paradigma para tener un desarrollo sostenible. Se plantea reutilizar estos recursos para contribuir a construir sustentable, sostenible y ecológico. Este estudio tiene como objetivo, demostrar que la propuesta diseño de concreto con sustitución parcial de los agregados por PET y caucho reciclados mejorará sus propiedades mecánicas, en veredas, incrementando su vida útil, su resistencia a la meteorización, la acción química y el desgaste. Se empleó metodología con nivel de investigación exploratoria y diseño de investigación experimental. Se analizó los resultados de los 84 ensayos, todas las muestras superaron al concreto convencional, siendo la muestra tres con mejores valores, supero resistencia a compresión en 8.38%, resistencia a la flexión en 19.17%, resistencia a la tracción en 24.16% y disminución de densidad 13.17%. Se concluye que, se logra el objetivo de esta investigación, tales como la disminución de la densidad del concreto, aumenta la resistencia a la compresión, tracción y flexión, ello represente ventajas medio ambientales y sociales. Sin embargo, la desventaja es que representa mayores costos en 47.01% respecto a la muestra patrón. / Disused Polyethylene Terephthalate and rubber, barrels are found in landfills, in rivers and oceans, their degradation rate is slow, now they have become part of the ecological crisis. A paradigm shift is vital for sustainable development. It is proposed to reuse these resources to contribute to building sustainable, sustainable and ecological. The objective of this study is to demonstrate that the proposed concrete design with partial replacement of aggregates by recycled PET and rubber will improve its mechanical properties in sidewalks, increasing its useful life, resistance to weathering, chemical action and wear. An exploratory research level methodology and experimental research design were used. The results of the 84 tests were analyzed, all the samples surpassed the conventional concrete, being the sample three with the best values, I surpass compression resistance in 8.38%, flexural resistance in 19.17%, tensile strength in 24.16% and decrease density 13.17%. It is concluded that, the objective of this research is achieved, such as the decrease in the density of the concrete, the resistance to compression, traction and flexión increases, this represents environmental and social advantages. However, the disadvantage is that it represents higher costs in 47.01% compared to the standard sample. / Tesis