The objective of this thesis is two-fold: to analyze the directional calibration of a 3-hole probe in steady flow and to develop a method for the interpretation of measurements recorded with a novel, fast-response Pitot-type probe in unsteady, turbulent flow. Calibration data for the 3-hole probe’s two side ports was taken in the steady, non-turbulent region of a free jet and was evaluated for symmetry. In addition, data that was recorded using one side port in two independent calibration runs was compared to study repeatability. Misalignment was found between the nominally symmetric data sets, which may be the result of geometric probe tip defects or a misalignment of the side ports within -2 to -10 degrees. This misalignment suggested that the two probe ports must both be calibrated. The two data sets compared for repeatability were almost indistinguishable, suggesting that probe alignment was very repeatable over multiple calibration runs. This result implied that only one calibration run may be necessary for a single probe as well as for multiple probes having nearly identical tip geometry. These methods and findings from the 3-hole probe calibration provide useful processes and considerations for the calibration of directionally sensing pressure probes. Regarding the fast-response Pitot-type probe, measurements were conducted using the same free jet as was used with the 3-hole probe. The fast-response probe, which contains a Kulite sensor fitted in the sensing orifice of a Pitot tube, was positioned at incremental centerline locations in the unsteady, turbulent region of the jet flow, and mean and dynamic pressure data were recorded. Measurements were also taken at incremental centerline locations with a standard Pitot tube and a constant temperature hot wire anemometer. The Kulite mean pressure data and standard Pitot tube data were compared directly and agreed well. The hot wire data and a relevant turbulence model was used to generate mean pressure predictions, which correlated reasonably with a slight offset from the Kulite sensor and Pitot probe mean data. Next, the dynamic pressure data from the Kulite sensor was compared with predictions generated by the hotwire data, literature static pressure fluctuation data, and a second relevant turbulence model. In the centerline region where turbulence quantities begin to stabilize, the Kulite sensor data and predictions agreed reasonably well, within 7%. Thus, while not delivering ideal results, the turbulence models used provide a plausible method for the interpretation of the fast-response Pitot-type probe pressure measurements.

No description available.

The popularity of the internal combustion engine (ICE) vehicles has contributed to global warming problem and degradation of air quality around the world. Furthermore, the vehicles??? massive demand on gas has played a role in the depletion of fossil fuel reserves and the considerable rise in the gas price over the past twenty years. Those existing challenges force the auto-industry to move towards the technology development of vehicle electrification. An electrified vehicle is driven by one or more electric motors. And the electricity comes from the onboard energy storage system (ESS). Currently, no single type of green energy source could meet all the requirements to drive a vehicle. A hybrid energy storage system (HESS), as a combination of battery and ultra-capacitor units, is expected to improve the overall performance of vehicles??? ESS. This thesis focuses on the design of HESS and the development of a HESS prototype for electric vehicles (EVs) and hybrid electric vehicles (HEVs). Battery unit (BU), ultra-capacitor unit (UC) and a DC/DC converter interfacing BU and UC are the three main components of HESS. The research work first reviews literatures regarding characteristics of BU, UC and power electronic converters. HESS design is then conducted based on the considerations of power capability, energy efficiency, size and cost optimization. Besides theoretical analysis, a HESS prototype is developed to prove the principles of operation as well. The results from experiment are compared with those from simulation.

Wave energy converter (WEC) harnesses energy from the ocean to produce electrical power. The electrical power produced by the WEC is fluctuating and is not maximized as well, due to the varying ocean conditions. As a consequence, without any intermediate power conversion stage, the output power from the WEC can not be fed into the grid. To feed WEC output power into the grid, a two-stage power conversion topology is used, where the WEC output power is first converted into DCpower through rectification, and then a DC-AC converter (inverter) is used to supply AC power into the grid. The main motive of this research is to extract maximum electrical power from the WEC by active rectification and smoothing the power fluctuation of the wave energy converter through a hybrid energy storage system consisting of battery and flywheel. This research also illustrates active and reactive power injection to the grid according to load demand through a voltage source inverter.

No description available.

Cette thèse est le volet expérimental d’un projet de recherche qui vise à développer un code de calcul qui prédit finement la micro ségrégation des aciers présentant une réaction péritectique. La caractérisation expérimentale de la micro ségrégation a été menée grâce à des essais de solidification dirigée et des essais de trempe en cours de solidification dirigée ainsi que sur des échantillons de lingots industriels. Les alliages sélectionnés font partie des systèmes Fe-C-Ni et Fe-C-Cr. Nous avons d’abord étudié sur des aciers solidifiés l’effet de la composition chimique et l’effet du premier solide ferrite / austénite sur la micro ségrégation. Par la suite nous avons caractérisé la formation de la micro ségrégation avec et sans réaction péritectique. On a montré aussi les effets de la taille de la structure, de la microstructure (dendritique / cellulaire)et de la texture du grain sur la micro ségrégation (colonnaire / équiaxe) sur la micro ségrégation. Enfin, nous avons comparé les résultats expérimentaux avec les résultats de la modélisation. / This PhD work is an experimental part of a global R&D project witech aim to study the microsegregation in peritectic steels. The experimental investigations were made by a Directional Solidification device (DS), Quenched Directional Solidification (QDS) and from parts of industrials ingots. The alloys selected were taken from the Fe-C-Ni and Fe-C-Cr systems. On the solidified steels we investigate the effect of the chemical composition and the first solid (ferrite/austenite) on the microsegregation. The next step was the characterization of the microsegregation during the solidification with and without a peritectic reaction. Afterwards we study the effects of the length of the structure, the microstructure (dendritic/cellular) and the texture of the grains (columnar/equiaxed) on the microsegregation. At the end we have do a comparison bethween the experimental results and those from the numerical simulations

This thesis describes investigations into the optical and device design of organic light-emitting diodes (OLEDs) with the aim of exploring the factors controlling the spatial emission pattern of OLEDs and developing novel OLEDs with directional emission by applying wavelength-scale photonic microstructure. The development of directional OLEDs was broken down into two steps: the development of efficient narrow linewidth OLEDs and the integration of wavelength-scale photonic microstructures into narrow linewidth OLEDs. The narrow linewidth OLEDs were developed using europium (Eu) complexes. The electrical optimisation of solution-processed Eu-based OLEDs using commercially available materials was investigated. The optimised Eu-based OLEDs gave an external quantum efficiency of 4.3% at a display brightness of 100 cd/m². To our knowledge, this is the highest efficiency reported for solution-processed Eu-based OLED devices, and the efficiency roll-off has been reduced compared with other reported references. Photonic microstructures were applied to develop directional OLEDs using the efficient Eu-based OLEDs. Two contrasting strategies were used. One was to embed photonic microstructures into Eu-based OLEDs, the other was to couple photonic microstructures externally onto the devices. The microstructured devices developed by the former strategy boosted the emitted power in desired angles in both s- and p-polarisations and doubled the fraction of emission in an angle range of 4⁰. The devices developed by the external coupling strategy achieved even higher directionality and the out-coupled emission was a confined beam with easy control of beam steering. Around 90% of the emitted power was confined in an angular range of 20⁰ in the detection plane. The optical properties can be optimised independently without compromising the electrical properties of devices, which gives major advantages in terms of effectiveness and versatility. Optical models were also developed to investigate the out-coupling mechanism of various trapped modes and develop OLEDs with stronger directionality.

Les automates cellulaires sont à la fois un modèle de calcul parallèle, un système complexe et un système dynamique. Ils fonctionnent de manière synchrone et en temps discret, leur particularité est que les fonctions qu'ils définissent sont issues de l'application simultanée, en tout point de l'espace, d'une règle d'évolution locale. L'ensemble limite est un objet classique des systèmes dynamiques, c'est l'ensemble des états que le système peut atteindre arbitrairement tard. Il a été très étudié dans le cadre des automates cellulaires, et les résultats sont nombreux. Parmi ces résultats, un théorème de Rice démontré par Jarkko Kari dit que toute propriété des ensembles limites est indécidable. Dans ce mémoire, on ne s'intéresse plus à l'ensemble limite traditionnel, mais à une variante pour laquelle on utilise une mesure sur l'espace des entrées, sélectionnant ainsi les comportements susceptibles d'apparaître arbitrairement tard et souvent. Ce nouvel ensemble, que l'on nomme ensemble mu-limite, a été introduit en 2000 par Petr Kurka et Alejandro Maass. La plupart des résultats sur les ensembles limites ne se transposent pas naturellement. On étudie la famille des ensembles mu-limites d'automates cellulaires. On montre que sous certaines contraintes sur la dynamique, l'ensemble mu-limite peut être entièrement décrit. On classe ainsi les automates en fonction de ces contraintes. Dans le cas général, on montre l'existence d'automates cellulaires ayant comme ensembles mu-limites un grand nombre d'ensembles complexes. On finit par montrer un théorème de Rice pour les ensembles mu-limites d'automates cellulaires: tout propriété non triviale de ces ensembles est indécidable. / Cellular automata are simultaneously a model of parallel computation, a complex system and a dynamical system. They are synchronous and time is discrete. The functions defined by their application is the result of the synchronous application of the same local rule everywhere. The limit set is a classical tool of dynamical systems theory, it is the set of states the system can reach arbitrarily late. It has been studied often in the particular case of cellular automata and there are numerous results. Amongst them, a Rice's theorem proved by Jarkko Kari states that any non-trivial property of limit sets of cellular automata is undecidable. In this thesis, we do not consider the classical limit set, as we add a measure on the space of states of the system. Thus, we get a set which contains behaviors that appear arbitrarily far and often. This set is named mu-limit set and was introduced in 2000 by Petr Kurka and Alejandro Maass. Most of the results on limit sets cannot be directly adapted for mu-limit sets. We study the family of all mu-limit sets of cellular automata. We show that under some constraints on the dynamics, the mu-limit set can be entirely described. We then produce a classification of cellular automata according to these constraints. In the general case, we prove the existence of cellular automata whose mu-limit sets are among a large set of complex sets. We finally prove Rice's theorem for mu-limit sets: any non-trivial property is undecidable.

Smoothing filters have been extensively used for noise removal and image restoration. Directional filters are widely used in computer vision and image processing tasks such as motion analysis, edge detection, line parameter estimation and texture analysis. It is practically impossible to tune the filters to all possible positions and orientations in real time due to huge computation requirement. The efficient way is to design a few basis filters, and express the output of a directional filter as a weighted sum of the basis filter outputs. Directional filters having these properties are called "Steerable Filters." This thesis work emphasis is on the implementation of proposed computationally efficient separable and steerable Gaussian smoothers on a Xilinx VirtexII Pro FPGA platform. FPGAs are Field Programmable Gate Arrays which consist of a collection of logic blocks including lookup tables, flip flops and some amount of Random Access Memory. All blocks are wired together using an array of interconnects. The proposed technique [2] is implemented on a FPGA hardware taking the advantage of parallelism and pipelining.

Studiens syfte är att generera kunskap om vad som påverkar förändringsprojekts utfall, genom att studera kommunalt anställdas upplevelser av att ansvara för interna förändringsprojekt. Studien är ett försök att belysa förändringsprojekt sett som processer som drivs med hjälp av projektlogik, för att ytterligare förstå svårigheter och möjligheter i kommunala projektsammanhang. För att besvara syftet utfördes semistrukturerade intervjuer med efterföljande analys utifrån ett teoretiskt ramverk, baserad på tidigare forskning inom projektledning. Intervjuerna omfattar personer anställda i olika svenska kommuner, ansvariga för framtagande och implementering av handlingsplaner mot våldsbejakande extremism. Resultatet påvisar att bristande samsyn gällande mål och prioritering samt osäkerhet gällande tillvägagångssätt upplevs försvåra projekten, medan personliga relationer och metoder som främjar samarbete, samsyn och kunskapsdelning upplevs underlätta projekten. Studien drar slutsatsen att svåra genomföranden hänger samman med låg prioriteringsnivå av projektet i organisationen, samt att de metoder som avses användas för att hantera svårigheter är oanvändbara utan handlingsutrymme genom personliga relationer inom organisationen. Genom att definiera förändringsprojekt som process med själva förändringen i fokus stärks också förutsättningarna för att kunna sätta projektmål och ramar som möjliggör ett lyckat resultat. / The aim of this study is to generate knowledge about what affects the outcome of change projects, by studying how employees in public organisations experience their work as responsible for managing change projects. The study is an attempt to shed light on change projects seen as processes that are managed by project logic, to further understand difficulties and possibilities in public project contexts. To answer the aim semi-structured interviews were conducted with following analysis through a theoretical framework, based on previous research of project management. The interviews include employees in different Swedish municipalities, responsible for developing and implementing action plans addressing violent extremism. The result shows that lack of consensus regarding goals and prioritizations as well as uncertainty regarding procedures are experienced as aggravating, while personal relations and methods supporting cooperation, consensus and knowledge-sharing are experienced as facilitating. The study concludes that difficult procedures are connected to low level of priority of the project in the organisation, as well as the methods that are intended to be used to reduce complexity are useless without room for action through personal relations within the organisation. By defining change projects as processes with the actual change in focus, the prerequisite to be able to set targets and frames that enables successful results are also strengthened.