No description available.

No description available.

This thesis paper supports the Master of Fine Arts exhibition at the Slocumb Galleries, East Tennessee State University, from March 14th through March 18th, 2011. The exhibit is composed of nine oil paintings depicting an invented story about two characters who create a soup for a cooking competition. The show A Matter of Taste chronicles an allegory concerning the evaluation of creative works. Through Gaudie and Baudie's "odd" recipe this work illustrates the ways in artists and art audiences interact and determine artistic value. The work is inspired by techniques in distortion and narrative painting. The following expands on the ideas, influences, techniques, and concepts that helped to create the exhibit.

Serpentine diffusers have become a common feature in modern aircraft as they allow for certain benefits that are impossible with a traditional linear configuration. With the benefits, however, come certain disadvantages, namely flow distortions that reduce engine efficiency and decrease engine surge stability margins. These distortions are now being researched comprehensively to determine solutions for mitigating the adverse effects associated with them. This study investigates how varying the freestream turbulence intensity of the flow entering a serpentine diffuser affects the distortion patterns that are produced by the diffuser. Experiments were performed with a model serpentine diffuser on the Annular Cascade Facility of the Air Force Research Laboratory at Wright-Patterson Air Force Base. Hot wire anemometry was used to measure inlet turbulence, while static pressure probes located axially along the upper and lower surface of the model diffuser and total pressure probes located across the aerodynamic interface plane (AIP) were used to measure the distortion patterns of the flow passing through the diffuser. Varying levels of inlet freestream turbulence, ranging from 0 to 4%, were generated using square and round bar turbulence screens in three distinct test configurations. Axial static pressure measurements indicate that increasing turbulence slightly affects flow separation development downstream of the second turn. This effect is also seen at the AIP where the total pressure recovery increases with increasing level of inlet turbulence in the region of flow separation at the upper surface. The total pressure recovery along the lower surface is also seen to be increased with higher inlet turbulence. However, total pressure recovery increase across the entire AIP is almost negligible. Overall, the inlet freestream turbulence has a minor effect on the distortion patterns caused by the serpentine diffuser when compared with proven active inlet flow control methods.

No description available.

As a contribution to advancing turbofan engine ground test technology in support of propulsion system integration in modern conceptual aircraft, a novel inlet distortion generator (ScreenVaneTM) was invented. The device simultaneously reproduces combined inlet total pressure and swirl distortion elements in a tailored profile intended to match a defined turbofan engine inlet distortion profile. The device design methodology was intended to be sufficiently generic to be utilized in support of any arbitrary inlet distortion profile yet adequately specific to generate high-fidelity inlet distortion profile simulation. For the current investigation, a specific inlet distortion profile was defined using computational analysis of a conceptual boundary layer ingesting S-duct turbofan engine inlet. The resulting inlet distortion profile, consisting of both total pressure and swirl distortion elements, was used as the objective profile to be matched by the ScreenVane in a turbofan engine ground test facility. A ScreenVane combined inlet total pressure and swirl distortion generator was designed, computationally analyzed, and experimentally validated. The design process involved specifying a total pressure loss screen pattern and organizing a unique arrangement of swirl inducing turning vanes. Computational results indicated that the ScreenVane manufactured distortion profile matched the predicted S-duct turbofan engine inlet manufactured distortion profile with excellent agreement in pattern shape, extent, and intensity. Computational full-field total pressure recovery and swirl angle profiles matched within approximately 1% and 2.5° (RMSD), respectively. Experimental turbofan engine ground test results indicated that the ScreenVane manufactured distortion profile matched the predicted S-duct turbofan engine inlet manufactured distortion profile with excellent agreement in pattern shape, extent, and intensity. Experimental full-field total pressure recovery and swirl angle profiles matched within approximately 1.25% and 3.0° (RMSD), respectively. Following the successful reproduction of the S-duct turbofan engine inlet manufactured distortion profile, a turbofan engine response evaluation was conducted using the validated ScreenVane inlet distortion generator. Flow measurements collected at discrete planes immediately upstream and downstream of the fan rotor isolated the component for performance analysis. Based on the results of this particular engine and distortion investigation, the adiabatic fan efficiency was negligibly altered while operating with distorted inflow conditions when compared to nominal inflow conditions. Fuel flow measurements indicated that turbofan engine inlet air mass flow specific fuel consumption increased by approximately 5% in the presence of distortion. While a single, specific turbofan engine inlet distortion profile was studied in this investigation, the ScreenVane methodology, design practices, analysis approaches, manufacturing techniques, and experimental procedures are applicable to any arbitrary, realistic combined inlet total pressure and swirl distortion. / Doctor of Philosophy / As a contribution to advancing turbofan engine ground test technology in support of propulsion system integration in modern conceptual aircraft, a novel inlet distortion generator (ScreenVaneTM) was invented. The device simultaneously reproduces combined inlet total pressure and swirl distortion elements in a tailored profile intended to match a defined turbofan engine inlet distortion profile. The device design methodology was intended to be sufficiently generic to be utilized in support of any arbitrary inlet distortion profile yet adequately specific to generate high-fidelity inlet distortion profile simulation. For the current investigation, a specific inlet distortion profile was defined using computational analysis of a conceptual boundary layer ingesting S-duct turbofan engine inlet. The resulting inlet distortion profile, consisting of both total pressure and swirl distortion elements, was used as the objective profile to be matched by the ScreenVane in a turbofan engine ground test facility. A ScreenVane combined inlet total pressure and swirl distortion generator was designed, computationally analyzed, and experimentally validated. The design process involved specifying a total pressure loss screen pattern and organizing a unique arrangement of swirl inducing turning vanes. Computational and experimental results indicated that the ScreenVane manufactured distortion profile matched the predicted S-duct turbofan engine inlet manufactured distortion profile with excellent agreement in pattern shape, extent, and intensity. Following the successful reproduction of the S-duct turbofan engine inlet manufactured distortion profile, a turbofan engine response evaluation was conducted using the validated ScreenVane inlet distortion generator. Flow measurements collected at discrete planes immediately upstream and downstream of the fan rotor isolated the component for performance analysis. Based on the results of this particular engine and distortion investigation, the adiabatic fan efficiency was negligibly altered while operating with distorted inflow conditions when compared to nominal inflow conditions. Fuel flow measurements indicated that turbofan engine inlet air mass flow specific fuel consumption increased in the presence of distortion. While a single, specific turbofan engine inlet distortion profile was studied in this investigation, the ScreenVane methodology, design practices, analysis approaches, manufacturing techniques, and experimental procedures are applicable to any arbitrary, realistic combined inlet total pressure and swirl distortion.

The use of serpentine boundary layer ingesting (BLI) diffusers offers a significant benefit to the performance of Blended Wing Body aircraft. However, the inherent diffuser geometry combined with a thick ingested boundary layer creates strong secondary flows that lead to severe flow distortion at the engine face, increasing the possibility of engine surge. This study investigated the use of enabling active flow control methods to reduce engine-face distortion. An ejector-pump based system of fluidic actuators was used to directly manage the diffuser secondary flows. This system was modeled computationally using a boundary condition jet modeling method, and tested in an ejector-driven wind tunnel facility. This facility is capable of simulating the high-altitude, high subsonic Mach number conditions representative of BWB cruise conditions, specifically a cruise Mach number of 0.85 at an altitude of 39,000 ft. The tunnel test section used for this experiment was designed, built, and tested as a validation tool for the computational methods. This process resulted in the creation of a system capable of efficiently investigating and testing the fundamental mechanisms of flow control in BLI serpentine diffusers at a minimum of time and expense. Results of the computational and wind tunnel analysis confirmed the large potential benefit of adopting fluidic actuators to control flow distortion in serpentine BLI inlets. Computational analysis showed a maximum 71% reduction in flow distortion at the engine face through the use of the Pyramid 1 ejector scheme, and a 68% reduction using the Circumferential ejector scheme. However, the flow control systems were also found to have a significant impact on flow swirl. The Pyramid 1 ejector scheme was found to increase AIP flow swirl by 64%, while the Circumferential ejector scheme reduced flow swirl by 30%. Computational analyses showed that this difference was the result of jet interaction. By keeping the jet flows separate and distinct, the diffuser secondary flows could be more efficiently managed. For this reason, the most practically effective flow control scheme was the Circumferential ejector scheme. Experimental results showed that the computational analysis slightly over-predicted flow distortion. However, the trends are accurately predicted despite slight variances in freestream Mach number between runs and a slightly lower tested altitude. / Master of Science

A three-dimensional CFD program was used to predict the flow field that would enter a downstream fan or compressor rotor under the influence of an upstream thermal distortion. Two distortion generation techniques were implemented in the model; (1) a thermal source and (2) a heated flow injection method. Results from the investigation indicate that both total pressure and velocity boundary conditions at the compressor face are made non-uniform by the upstream thermal distortion, while static pressure remains nearly constant. Total pressure at the compressor face was found to vary on the order of 10%, while velocity varies from 50-65%. Therefore, in modeling such flows, neither of these latter two boundary conditions can be assumed constant under these conditions. The computational model results for the two distortion generation techniques were compared to one another and evaluations of the physical practicality of the thermal distortion generation methods are presented. Both thermal distortion methods create total temperature distortion magnitudes at the compressor face that may affect rotor blade vibration. Both analyses show that holding static pressure constant is an appropriate boundary condition for flow modeling at the compressor inlet. The analyses indicate that in addition to the introduction of a thermal distortion, there is a potential to generate distortion in total pressure, Mach number, and velocity. Depending on the method of thermally distorting the inlet flow, the flow entering the compressor face may be significantly non-uniform. The compressor face boundary condition results are compared to the assumptions of a previous analysis (Kenyon et al., 2004) in which a 25 R total temperature distortion was applied to a computational fluid dynamics (CFD) model of a fan geometry to obtain unsteady blade pressure loading. Results from the present CFD analyses predict similar total temperature distortion magnitudes corresponding to the total temperature variation used in the Kenyon analyses. However, the results indicate that the total pressure and circumferential velocity boundary conditions assumed uniform in the Kenyon analyses could vary by the order of 2% in total pressure and approximately 8% in velocity distortion. This supports the previously stated finding that assuming a uniform total pressure profile at the compressor inlet may be an appropriate approximation with the presence of a weak thermal distortion, while assuming a constant circumferential velocity boundary condition is likely not sufficiently accurate for any thermal distortion. In this work, the referenced Kenyon investigation and others related to the investigation of distortion-induced aeromechanical effects in this compressor rotor have assumed no aerodynamic coupling between the duct flow and the rotor. A full computational model incorporating the interaction between the duct flow and the fan rotor would serve to alleviate the need for assuming boundary conditions at the compressor inlet. / Master of Science

An experimental and analytical investigation was conducted to gain insight and ultimately predict the dynamic flow response of a fan rotor with inlet flow distortion. Rotor exit total pressure circumferential profiles were accurately predicted using frequency response functions derived from experimental rotor response data. Using these predicted profiles, an initial attempt was made at predicting the dynamic (distorted) stage characteristics of the test machine with promising results. The first step of this research was an experimental investigation to gather unsteady rotor response data. The steady three-dimensional inlet flow of an isolated rotor subjected to inlet distortion was obtained using a five-hole pneumatic prism probe. Exit flow dynamic wake data were obtained using a piggyback steady/unsteady total pressure probe in non-nulling mode. Inlet and exit data were collected for eighteen different combinations of distortion level, operating point, and measurement span. Frequency response functions were generated and then averaged for each operating regime, span, and distortion intensity, assuming the data to be stationary and ergodic. These 'generalized' FRF's were used to predict the rotor exit total pressure profile. These pressure profiles were then used in an initial attempt to predict the dynamic stage (distorted) characteristics of the test machine. Best predictions resulted when an FRF was used for individual operating regimes, defined with respect to rotor blade mean aerodynamic loading. / Master of Science

Universal Mobile Telecommunications Systems (UMTS) is the preferred third generation (3G) communication standard for mobile communications and will provide worldwide coverage, a convenient software technology and very high data rate. The high data rate, especially, requires the use of bandwidth-efficient modulation schemes such as Quadrature Phase Shift Keying (QPSK). But modulation schemes such as QPSK need, in turn, a very linear power from the output of the transmitter power amplifier in order to meet the spectral requirements. A linear power amplifier, traditionally, has very low energy efficiency. Poor energy efficiency directly affects operational costs and causes thermal heating issues in base station transmitters. Thus the power amplifier designer is forced to trade-off between linearity and efficiency. As a result of this trade-off a Class-AB power amplifier is most often used in QPSK based systems. Class-AB power amplifiers provide acceptable linearity at efficiency values around 45-50% typically. This compromise is not a satisfactory solution but is inevitable while using traditional power amplifier design techniques. This thesis details the use of a Class-F amplifier with carefully chosen bias points and harmonic traps to overcome this problem. Class-F amplifiers are usually considered as very high efficiency (80% or more power-added efficiency) amplifiers where the high efficiency is obtained through the use of harmonic traps (L-C filters or quarter-wavelength transmission lines), which provide suitable terminations (either open or short) for the harmonics generated. By doing this, a square wave drain voltage and a peaked half-sinusoidal drain current out-of-phase by 180 are produced. Since only a drain voltage or a drain current exists at any given time, the power dissipation is ideally zero resulting in 100% theoretical efficiency. These very high efficiency values are usually associated with poor linearity. However the linearity can be improved to meet the design standards but compromising on efficiency. Even after this is done, efficiencies are usually 10 to 15% greater than a traditional Class AB power amplifier with similar linearity performance. Thus efficiency can be improved without affecting linearity by the use of Class-F power amplifiers. In order to verify this theory, a Class-AB and a Class-F power amplifier are designed using Motorola's high voltage laterally diffused metal oxide semiconductor (LDMOS) transistor. The choice of bias points and the design of the harmonic traps are very critical for the Class-F performance and hence were designed after careful consideration. The designs were simulated on Agilent's Advanced Design System (ADS) and the simulated results were compared for three different power levels namely, the peak power, 3 dB below peak power and 6 dB below peak power. At all of these power levels it was noted that the Class-F and Class-AB power amplifiers have very similar linearity performance whereas the Class-F power amplifiers show about 10% improvement in efficiency in comparison to the Class-AB power amplifiers. / Master of Science