- About
-
The Global ETD Search service is a free service for researchers
to find electronic theses and dissertations. This service is
provided by the
Networked Digital Library of Theses and Dissertations.
Our metadata is collected from universities around the world. If you manage a university/consortium/country archive and want to be added, details can be found on the NDLTD website.
Search results
Showing 11 to 18 of 18 (0.015 seconds)| 11 |
Spray and Wall Film Modeling with Conjugate Heat Transfer in OpenFOAMSjölinder, Emil January 2012 (has links)
This master thesis was provided by Scania AB. The objective of this thesis was to modify an application in the free Computational Fluid Dynamics software OpenFOAM to be able to handle spray and wall film modeling of a Urea Water Solution together with Conjugate Heat Transfer. The basic purpose is to widen the knowledge of the vaporization process of a Urea Water Solution in the exhaust gas after treatment system for a diesel engine by using OpenFOAM. First, urea has been modeled as a very viscous liquid at low temperature to mimic the solidication process of urea. Second, the development of the new application has been done. At last, test simulations of a simple test case are performed with the new application. The results are then compared with simplied hand calculations to verify a correct behavior of certain exposed source terms. The new application is working properly for the test case but to ensure the reliability, the results need to be compared with another Computational Fluid Dynamics software or more preferable, real experiments. For more advanced geometries, the continued development presented last in this thesis is highly recommended to follow.
|
| 12 |
Development of an Efficient Viscous Approach in a Cartesian Grid Framework and Application to Rotor-Fuselage InteractionLee, Jae-doo 18 May 2006 (has links)
Despite the high cost of memory and CPU time required to resolve the boundary layer, a viscous unstructured grid solver has many advantages over a structured grid solver such as the convenience in automated grid generation and shock or vortex capturing by solution adaption. Since the geometry and flow phenomenon of a helicopter are very complex, unstructured grid-based methods are well-suited to model properly the rotor-fuselage interaction than the structured grid solver. In present study, an unstructured Cartesian grid solver is developed on the basis of the existing solver, NASCART-GT. Instead of cut-cell approach, immersed boundary approach is applied with ghost cell boundary condition, which increases the accuracy and minimizes unphysical fluctuations of the flow properties. The standard k-epsilon model by Launder and Spalding is employed for the turbulence modeling, and a new wall function approach is devised for the unstructured Cartesian grid solver. It is quite challenging and has never done before to apply wall function approach to immersed Cartesian grid. The difficulty lies in the inability to acquire smooth variation of y+ in the desired range due to the non-body-fitted cells near the solid wall. The wall function boundary condition developed in this work yields stable and reasonable solution within the accuracy of the turbulence model. The grid efficiency is also improved with respect to the conventional method. The turbulence modeling is validated and the efficiency of the developed boundary condition is tested in 2-D flow field around a flat plate, NACA0012 airfoil, axisymmetric hemispheroid, and rotorcraft applications.
For rotor modeling, an actuator disk model is chosen, since it is efficient and is widely verified in the study of the rotor-fuselage interaction. This model considers the rotor as an infinitely thin disk, which carries pressure jump across the disk and allows flow to pass through it. The full three dimensional calculations of Euler and RANS equations are performed for the GT rotor model and ROBIN configuration to test implemented actuator disk model along with the developed turbulence modeling. Finally, the characteristics of the rotor-fuselage interaction are investigated by comparing the numerical solutions with the experiments.
|
| 13 |
Estudo numérico tridimensional de um dispositivo de galgamento para conversão de energia das ondas do mar em energia elétrica aplicando o método Constructal DesignMachado, Bianca Neves January 2016 (has links)
O princípio operacional do dispositivo de galgamento consiste de uma estrutura que utiliza uma rampa para direcionar as ondas incidentes para o reservatório. A água armazenada retorna para o oceano após a passagem por uma turbina que está acoplada a um gerador de energia elétrica. O presente trabalho propõe dois estudos numéricos a respeito de um conversor de energia das ondas do mar do tipo galgamento. Para ambos os casos, o objetivo do estudo é a aplicação do método Design Construtal na definição da melhor forma para a rampa de modo a maximizar a massa de água que entra no reservatório, conduzindo a uma maior geração de energia elétrica. O grau de liberdade b/B, isto é, a razão entre a base superior e a base inferior da rampa trapezoidal, foi otimizado, mantendo-se fixos a área total do tanque de ondas, a área da rampa e as características da onda. Para a análise numérica do princípio de funcionamento deste dispositivo foi empregado um domínio computacional tridimensional (3D), gerado através do software GAMBIT, onde o conversor é acoplado a um tanque de ondas regulares. A solução das equações de conservação e a equação do transporte da fração volumétrica foi realizada com o código comercial de Dinâmica dos Fluidos Computacional FLUENT, que é baseado no Método de Volumes Finitos (MVF). Aplica-se o modelo multifásico Volume of Fluid (VOF) no tratamento da interação água-ar. Para o primeiro estudo, as características da onda regular empregada estavam em escala de laboratório. Os resultados mostraram que houve uma razão ótima (b/B)o = 0.43, que maximiza a quantidade de água que entra no reservatório para o caso estudado. Para ambos os casos, a razão ótima foi encontrada para o extremo inferior do grau de liberdade, além dos resultados apontarem um aumento significativo na massa admitida no reservatório e, por consequente, um maior aproveitamento das ondas incidentes. / The operational principle of an overtopping device consists of a structure which utilizes a ramp to direct incident waves to the reservoir. The stored water returns to the ocean after passing through a turbine that is coupled to an electric generator. This work proposes two numerical studies of a WEC of sea waves of the type overtopping. In both cases, the objective of the study is the application of Constructal Design method to define the best geometry of the ramp which maximizes the mass of water entering the reservoir, leading to increase the generation of electricity. The degree of freedom b/B, that is, the ratio between the upper base and the lower base of the trapezoidal ramp, has been optimized, keeping fixed the total area of the wave tank, the area of the ramp and the wave characteristics. For the numerical analysis of the working principle of this device it was used a three-dimensional computational domain (3D) generated by GAMBIT software where the device is inserted to a tank of regular waves. The solution of conservation equations and equation of transport of the volumetric fraction was carried out with the Commercial Code of Computational Fluid Dynamics FLUENT, which is based on Finite Volume Method (FVM). It was applied the multiphase model Volume of Fluid (VOF) in the treatment of the interaction water-air. For the first study, the characteristics of the employed regular wave were on a laboratory scale. The results showed that there were an optimal ratio (b/B)o = 0.43, which maximizes the amount of water entering the reservoir for the case study. For the second study, the characteristics of the regular wave were employed at actual scale and the results showed that there was an optimum ratio (b/B)o = 0.38, which maximizes the amount of water entering the reservoir for the case study. In both cases, the optimum ratio is found for the extreme lower of freedom of degree and the results showed a significant increase in the mass allowed in the reservoir and, consequently, larger use of the incident waves.
|
| 14 |
Estudo numérico tridimensional de um dispositivo de galgamento para conversão de energia das ondas do mar em energia elétrica aplicando o método Constructal DesignMachado, Bianca Neves January 2016 (has links)
O princípio operacional do dispositivo de galgamento consiste de uma estrutura que utiliza uma rampa para direcionar as ondas incidentes para o reservatório. A água armazenada retorna para o oceano após a passagem por uma turbina que está acoplada a um gerador de energia elétrica. O presente trabalho propõe dois estudos numéricos a respeito de um conversor de energia das ondas do mar do tipo galgamento. Para ambos os casos, o objetivo do estudo é a aplicação do método Design Construtal na definição da melhor forma para a rampa de modo a maximizar a massa de água que entra no reservatório, conduzindo a uma maior geração de energia elétrica. O grau de liberdade b/B, isto é, a razão entre a base superior e a base inferior da rampa trapezoidal, foi otimizado, mantendo-se fixos a área total do tanque de ondas, a área da rampa e as características da onda. Para a análise numérica do princípio de funcionamento deste dispositivo foi empregado um domínio computacional tridimensional (3D), gerado através do software GAMBIT, onde o conversor é acoplado a um tanque de ondas regulares. A solução das equações de conservação e a equação do transporte da fração volumétrica foi realizada com o código comercial de Dinâmica dos Fluidos Computacional FLUENT, que é baseado no Método de Volumes Finitos (MVF). Aplica-se o modelo multifásico Volume of Fluid (VOF) no tratamento da interação água-ar. Para o primeiro estudo, as características da onda regular empregada estavam em escala de laboratório. Os resultados mostraram que houve uma razão ótima (b/B)o = 0.43, que maximiza a quantidade de água que entra no reservatório para o caso estudado. Para ambos os casos, a razão ótima foi encontrada para o extremo inferior do grau de liberdade, além dos resultados apontarem um aumento significativo na massa admitida no reservatório e, por consequente, um maior aproveitamento das ondas incidentes. / The operational principle of an overtopping device consists of a structure which utilizes a ramp to direct incident waves to the reservoir. The stored water returns to the ocean after passing through a turbine that is coupled to an electric generator. This work proposes two numerical studies of a WEC of sea waves of the type overtopping. In both cases, the objective of the study is the application of Constructal Design method to define the best geometry of the ramp which maximizes the mass of water entering the reservoir, leading to increase the generation of electricity. The degree of freedom b/B, that is, the ratio between the upper base and the lower base of the trapezoidal ramp, has been optimized, keeping fixed the total area of the wave tank, the area of the ramp and the wave characteristics. For the numerical analysis of the working principle of this device it was used a three-dimensional computational domain (3D) generated by GAMBIT software where the device is inserted to a tank of regular waves. The solution of conservation equations and equation of transport of the volumetric fraction was carried out with the Commercial Code of Computational Fluid Dynamics FLUENT, which is based on Finite Volume Method (FVM). It was applied the multiphase model Volume of Fluid (VOF) in the treatment of the interaction water-air. For the first study, the characteristics of the employed regular wave were on a laboratory scale. The results showed that there were an optimal ratio (b/B)o = 0.43, which maximizes the amount of water entering the reservoir for the case study. For the second study, the characteristics of the regular wave were employed at actual scale and the results showed that there was an optimum ratio (b/B)o = 0.38, which maximizes the amount of water entering the reservoir for the case study. In both cases, the optimum ratio is found for the extreme lower of freedom of degree and the results showed a significant increase in the mass allowed in the reservoir and, consequently, larger use of the incident waves.
|
| 15 |
Development and Application of the Boundary Singularity Method to the Problems of Hydrodynamic and Viscous Interaction.Mikhaylenko, Maxim A. January 2015 (has links)
No description available.
|
| 16 |
Two approaches to the study of detached flowsOttino, Gabriele 24 April 2009 (has links)
On étudie des phénomènes de séparation d'écoulement avec deux approches différentes. Dans la première partie, on considère des écoulements 2D, instationnaires, incompressibles et non visqueux. Un modèle analytique-numérique, basé sur la jonction d'une transformation conforme et d'une méthode aux tourbillons ponctuels, est construit pour définir l'écoulement potentiel dans un domaine doublement connecté où les corps sont caractérisés par une variation temporelle de leur circulation. En particulier, on s'intéresse à l'étude de l'écoulement autour d'un VAWT avec deux pales. Dans la seconde partie on considère des écoulements visqueux et compressibles. On construit un solveur qui résoud les équations de Navier-Stokes en y introduisant une technique de pénalisation: les corps sont modélisés comme des milieux poreux ayant une porosité très petite par rapport à la porosité du fluide extérieur. Cette technique permet d'utiliser des maillages cartésiens pour des géométries très complexes. / In the present work flow separation phenomena are investigated by means of two different approaches. In the first part, 2D unsteady incompressible inviscid flows are studied. An analytical-numerical model, based on the conjunction of a conformal mapping and a point vortex method, is built to define the potential flow field in a doubly connected domain where bodies are characterized by a variation in time of their circulation. In particular, the study of the unsteady flow past a 2-blade Darrieus VAWT is addressed. Until now the study of vortex motions has only been described in doubly-connected flow fields where the circulations have a constant null value. The flow field here analysed has a deep unsteadiness, which determines the circulations varying in time: so a technique is developed to uniquely define the circulations around the bodies. Three conditions result necessary to be imposed: in addition to the two Kutta conditions at the trailing edges, another one has to be imposed in order to respect the Kelvin theorem. With a classical configuration, this machine, experiencing angles of attack of opposite values, gives rise to complex vortex shedding phenomena that reduce its performances and stress its structure. In order to control the flow separation from the blades, an innovative solution is qualitatively investigated which consists of taking blade profiles provided with vortex trapping cavities. Interesting results are obtained, even if in the limit of inviscid flow. In the second part compressible viscous flows are taken into account. A fully Navier-Stokes equations solver is implemented introducing the penalization technique. The idea is to replace the bodies by the fluid, in a way that also into the bodies the penalized Navier-Stokes equations remain valid, respecting the boundary conditions on their contours. Starting from this purpose, the bodies are considered as porous media with a little porosity with respect to that of the external flow, which tends to infinity. This technique allows simple Cartesian meshes to be used, also for very complex geometries like those of industrial interest. The resulting code is tested on different flow fields, both steady and unsteady, both subsonic and supersonic, obtaining always a good agreement with other theoretical and numerical results described in literature.
|
| 17 |
Methodenentwicklung zur Simulation von Strömungen mit freier Oberfläche unter dem Einfluss elektromagnetischer WechselfelderBeckstein, Pascal 16 February 2018 (has links) (PDF)
Im Bereich der industriellen Metallurgie und Kristallzüchtung treten bei zahlreichen Anwendungen, wo magnetische Wechselfelder zur induktiven Beeinflussung von leitfähigen Werkstoffen eingesetzt werden, auch Strömungen mit freier Oberfläche auf. Das Anwendungsspektrum reicht dabei vom einfachen Aufschmelzen eines Metalls in einem offenen Tiegel bis hin zur vollständigen Levitation. Auch der sogenannte RGS-Prozess, ein substratbasiertes Kristallisationsverfahren zur Herstellung siliziumbasierter Dünnschichtmaterialien, ist dafür ein Beispiel. Um bei solchen Prozessen die Interaktion von Magnetfeld und Strömung zu untersuchen, ist die numerische Simulationen ein wertvolles Hilfsmittel. Für beliebige dreidimensionale Probleme werden entsprechende Berechnungen bisher durch eine externe Kopplung kommerzieller Programme realisiert, die für Magnetfeld und Strömung jeweils unterschiedliche numerische Techniken nutzen. Diese Vorgehensweise ist jedoch im Allgemeinen mit unnötigem Rechenaufwand verbunden. In dieser Arbeit wird ein neu entwickelter Methodenapparat auf Basis der FVM vorgestellt, mit welchem sich diese Art von Berechnungen effizient durchführen lassen. Mit der Implementierung dieser Methoden in foam-extend, einer erweiterten Version der quelloffenen Software OpenFOAM, ist daraus ein leistungsfähiges Werkzeug in Form einer freien Simulationsplattform entstanden, welches sich durch einen modularen Aufbau leicht erweitern lässt. Mit dieser Plattform wurden in foam-extend auch erstmalig dreidimensionale Induktionsprozesse im Frequenzraum gelöst.
|
| 18 |
Methodenentwicklung zur Simulation von Strömungen mit freier Oberfläche unter dem Einfluss elektromagnetischer WechselfelderBeckstein, Pascal 08 January 2018 (has links)
Im Bereich der industriellen Metallurgie und Kristallzüchtung treten bei zahlreichen Anwendungen, wo magnetische Wechselfelder zur induktiven Beeinflussung von leitfähigen Werkstoffen eingesetzt werden, auch Strömungen mit freier Oberfläche auf. Das Anwendungsspektrum reicht dabei vom einfachen Aufschmelzen eines Metalls in einem offenen Tiegel bis hin zur vollständigen Levitation. Auch der sogenannte RGS-Prozess, ein substratbasiertes Kristallisationsverfahren zur Herstellung siliziumbasierter Dünnschichtmaterialien, ist dafür ein Beispiel. Um bei solchen Prozessen die Interaktion von Magnetfeld und Strömung zu untersuchen, ist die numerische Simulationen ein wertvolles Hilfsmittel. Für beliebige dreidimensionale Probleme werden entsprechende Berechnungen bisher durch eine externe Kopplung kommerzieller Programme realisiert, die für Magnetfeld und Strömung jeweils unterschiedliche numerische Techniken nutzen. Diese Vorgehensweise ist jedoch im Allgemeinen mit unnötigem Rechenaufwand verbunden. In dieser Arbeit wird ein neu entwickelter Methodenapparat auf Basis der FVM vorgestellt, mit welchem sich diese Art von Berechnungen effizient durchführen lassen. Mit der Implementierung dieser Methoden in foam-extend, einer erweiterten Version der quelloffenen Software OpenFOAM, ist daraus ein leistungsfähiges Werkzeug in Form einer freien Simulationsplattform entstanden, welches sich durch einen modularen Aufbau leicht erweitern lässt. Mit dieser Plattform wurden in foam-extend auch erstmalig dreidimensionale Induktionsprozesse im Frequenzraum gelöst.
|
Page generated in 0.0249 seconds