With higher frequencies now being used in RFID systems, antennas are becoming much smaller resulting in more space on tags that can be used for innovative array designs to harvest more wireless energy. This master's thesis outlines and details a new methodology for designing and simulating the staggered pattern charge collector, a technique to improve harvesting wireless energy. Staggered pattern charge collectors enable RFID tag's to produce a higher DC voltage from a charge pump circuit by creatively using multiple arrays to increase the antenna power conversion gain without limiting the half power beamwidth. This thesis discusses the basics of patch antennas and charge pumps as well as an optimization technique for the staggered pattern array by maximizing integrated power conversion gain (IPCG). An example of a staggered pattern charge collector is fully specified from design through simulation, in preparation for fabrication. This methodology allows for the staggered pattern charge collectors to be designed, simulated, and fabricated quickly and effectively.

With rapid advances in semiconductor technologies and packaging schemes, wireless products have become more versatile, portable, inexpensive, and user friendly over last few decades. However, the ever-growing demand of consumers to share information efficiently at higher speeds requires higher data rates, increased functionality, lower cost, and more reliability. The 60-GHz-frequency band, with 7 GHz license-free bandwidth addresses, such demands, and promises a low-cost multi-Gbps wireless transmission with a power budget in the order of 100 mW. This dissertation presents the systematic development of key building blocks and integrated 60-GHz-receiver solutions. Two different approaches are investigated and implemented in this dissertation: (1) low-cost SiGe-based direct-conversion low-power receiver front-end utilizing gain-boosting techniques in the front-end low-noise amplifier, and (2) CMOS-based heterodyne receiver front-end suitable for high-performance single-chip 60 GHz transceiver solution. The ASK receiver chip, implemented using 0.18 ?m SiGe, presents a complete antenna-to-baseband multi-gigabit 60 GHz solution with the lowest reported power budget (25 pJ/bit) to date. The subharmonic direct conversion front-end, implemented using 0.18 ?m SiGe, presents excellent conversion properties with a 4 GHz DSB RF bandwidth. On the other hand, the CMOS heterodyne implementation of the 60 GHz front-end receiver, targeted towards a robust, single-chip, high-performance, low-power, and integrated 60 GHz transceiver solution, presents the most wideband receiver front-end reported to date. Finally, different multi-band and tunable millimeter-wave circuits are presented towards the future implementation of cognitive and multi-band millimeter-wave radio.

Στις σύγχρονες τηλεπικοινωνίες, χρησιμοποιείται μια μεγάλη γκάμα από RF μοντέλα, για τον υπολογισμό την μέσης τιμής ισχύος του σήματος εκπομπής για δεδομένη απόσταση από τον πομπό και για δεδομένη συχνότητα. Στις διεργασίες αυτές , επιδρούν στο δικό τους βαθμό διάφορες παράμετροι τοπολογικού (πληθυσμός , τύπος εμποδίων, πυκνότητα εμποδίων) και γεωγραφικού (μορφολογία εδάφους, υγρασία, διαμόρφωση χώρου) χαρακτήρα, αλλά και χαρακτηριστικά των πομποδεκτών ( συνήθως το ύψος και το κέρδος των κεραιών). Στις περισσότερες περιπτώσεις οι απώλειες όδευσης (Path Loss όπως είναι γνωστές στη διεθνή βιβλιογραφία) , εκφράζονται σε dB , σα συνάρτηση της συχνότητας λειτουργίας του υπό μελέτη συστήματος και της απόστασης ανάμεσα στον πομπό και το δέκτη ( πάντα για δεδομένα χαρακτηριστικά κεραιών και τύπο περιβάλλοντος). Έτσι μια ντετερμινιστική γνώση του μέσου path loss, που σε συνδυασμό με άλλες πιθανές απώλειες μας δίνει το σύνολο των απωλειών είναι εφικτή. O περιορισμός όσον αφορά στη συχνότητα και στις αποστάσεις , έχουν οδηγήσει τη σύγχρονη έρευνα στην επέκταση των υπαρχόντων μοντέλων , τόσο εξωτερικού όσο και εσωτερικού χώρου. Μια βασική παράμετρος της έρευνας στηρίζεται στην παραδοχή πως ο νόμος του αντιστρόφου τετραγώνου , ο οποίος περιγράφεται από την εξίσωση του Friis δε βρίσκει εφαρμογή, παρά μόνο σε περιβάλλοντα όπου επιτυγχάνεται LOS( Line of Sight) όδευση. Η τροποποίηση της παραπάνω εξίσωσης με δυναμικό ως προς το εκάστοτε περιβάλλον τρόπο , επιτρέπει πλέον τον υπολογισμό της μέσης ισχύος του σήματος σε σχετικά ρεαλιστικό βαθμό. Για παράδειγμα έχει προταθεί τροποποίηση με την τρίτη δύναμη της απόστασης για ένα σύνολο εφαρμογών , που αφορούν συστήματα ασυρμάτων τηλεπικοινωνιών εξωτερικού περιβάλλοντος.Ένα εσωτερικό περιβάλλον απαιτεί μια πολύ πιο ντετερμινιστική φόρμουλα υπολογισμού των απωλειών ώστε να μπορέσει ο μελετητής να υπολογίσει με αξιοπιστία την ισχύ του σήματος σε μια δεδομένη θέση. Η ακρίβεια λοιπόν των μοντέλων εξαρτάται άμεσα από την ικανότητά τους να απεικονίσουν και να αποδώσουν με τη σειρά τους , μέσω των υπολογισμών, όλα αυτά τα σύνθετα φαινόμενα με τον καλύτερο δυνατό τρόπο. Η πλειοψηφία των RF μοντέλων που αναπτύσσονται στα πλαίσια ακόλουθων παραγράφων, έχει αναπτυχθεί και αξιολογηθεί για συστήματα κυτταρικής κινητής τηλεφωνίας (GSM, PCS-1800, GPRS, UMTS). Προκειμένου να ξεπεραστούν διάφοροι περιορισμοί των αρχικών μοντέλων ως προς την συχνότητα λειτουργίας του συστήματος και την απόσταση πομπού-δέκτη (ουσιαστικά την εμβέλεια του μοντέλου), ορισμένες προεκτάσεις έχουν παρουσιαστεί σε διάφορες ερευνητικές εργασίες και χρησιμοποιούνται ευρέως . Ορισμένα νέα μοντέλα έχουν επίσης προστεθεί στα ήδη υπάρχοντα για τις συχνότητες συστημάτων κινητής τηλεφωνίας . Για άλλες περιοχές συχνοτήτων με έντονο ενδιαφέρον, πχ στα 5,2 GHz, διάφορες προτάσεις έχουν πραγματοποιηθεί, συχνά υποστηριζόμενες από μετρήσεις. Λαμβάνοντας υπόψη την συχνότητα των 2,4 GHz, δεν μπορούμε παρά να συμπεράνουμε ότι η όσο το δυνατόν πιο ακριβής και επιστημονικά αξιόπιστη μοντελοποίηση του ασύρματου διαύλου, ιδιαίτερα – άλλα όχι αποκλειστικά – για τοπολογίες εσωτερικών χώρων, είναι πολύ σημαντική για τον σχεδιασμό και την εύρυθμη λειτουργία των Wi-Fi συστημάτων και των WLAN δικτύων. Παρόλα αυτά, αν και στην υπάρχουσα βιβλιογραφία και στην διεθνή επιστημονική και ερευνητική κοινότητα υπάρχουν αρκετά σημαντικές εργασίες για την μοντελοποίηση του ασύρματου διαύλου στα 2,4 GHz , εντούτοις απουσίαζε, για πολύ καιρό, μία ολοκληρωμένη συγκριτική αντιπαραβολή και αξιολόγηση των βασικών θεωρητικών μοντέλων για τον υπολογισμό της μέσης απώλειας οδεύσεως στη συγκεκριμένη συχνότητα. Στα πλαίσια της εργασίας αυτής , θα προσπαθήσουμε να αξιοποιήσουμε το σύνολο των μετρήσεων και των δεδομένων που συλλέξαμε , σε ρεαλιστικές συνθήκες και για πραγματικά συστήματα μετάδοσης , τόσο να αξιολογήσουμε τα ήδη υπάρχοντα RF μοντέλα , όσο και να προβούμε στις απαραίτητες προτάσεις και τροποποιήσεις όπου αυτό κριθεί σκόπιμο. Επίσης για τη σκίαση επιχειρούμε εδώ μια προσέγγιση υπολογισμού μέσω της χρήσης των RF μοντέλων και την ενσωμάτωση όλων των χαρακτηριστικών διάδοσης , που αφορούν και στα δύο στοιχεία των μεγάλης κλίμακας διαλείψεων. Οι μετρήσεις μέσης λαμβανόμενης ισχύος πραγματοποιήθηκαν σε πέντε διαφορετικές τοπολογίες. Σε κάθε μία από αυτές τις τοπολογίες ελήφθησαν μετρήσεις της μέσης λαμβανόμενης ισχύος σε διάφορες δειγματοληπτικές αποστάσεις πομπού-δέκτη ούτως ώστε να είναι εφικτή, με έναν υψηλό βαθμό αξιοπιστίας, η αξιολόγηση των βασικών μοντέλων απωλειών οδεύσεως. Ταυτόχρονα, μέσα από αυτή την διαδικασία, αξιολογήθηκε η αξιοπιστία των μοντέλων αναφορικά με τις ιδιαιτερότητες της κάθε τοπολογίας, που αποτυπώνονται ποιοτικά και ποσοτικά στους μηχανισμούς διάδοσης του ραδιοσήματος σε κάθε περίπτωση. / In modern wireless communications, a wide range of RF models are used to provide the median (average) value of the signal strength at a given distance from the transmitter and for a given frequency spectrum. In this procedure, certain geographical (ground, humidity, terrain irregularities), topological (heavy or scattered population, type of obstacles, density of the buildings) characteristics of the area, as well as certain specifications of the transmitter and receiver antennas (most notably antenna height and antenna gain) have to be taken into consideration. In most cases, the mean value of the path loss is expressed in dB in dependence with the frequency of the operating system and the distance between the transmitter and the receiver (for given antenna characteristics and a certain type of environment where the system operates). Thus, a deterministic knowledge of the average path loss (which along with the average rain loss and diffraction loss provides the overall propagation loss in dB) is available. However, distance and frequency limitations have led research to a further study and expanding of the existing empirical and semi-empirical models , for both outdoor and indoor scenarios. A fundamental parameter-based study of the path loss models is based on the concept that the second power law that is predicted by the Friis equation does not apply in real-life scenarios except for standard LOS paths. The modified power law research allows engineers and scholars to calculate the mean received power of a signal transmitted over a wireless link in a more realistic approach. It has been suggested that the third-power law is more suitable for a plethora of applications based on wireless communications for an outdoor environment.The indoor propagation channel, in particular, demands a lot more than a deterministic formula of calculating the average signal strength as a function of distance and frequency. The increased impact of multipath and other propagation phenomena such as reflection and scattering, as well as the existence of many objects whose proportions are comparatively close to the wavelength of the operating wireless systems, render the propagation of a signal and its arrival at a receiver (mobile or fixed) a rather complex procedure. The precision of the path loss models depends heavily on their ability to demonstrate and reflect, in the calculations, these complex phenomena to the best possible way .The majority of these models have been developed and validated for mobile telephony systems in both outdoor and indoor schemes (GSM, PCS-1800, GPRS, UMTS). Certain extensions of many of these models were conducted in order to expand the frequency and distance limitation of the original formulas. New empirical models have also been suggested for these certain frequencies .Taking into account the very sensitive and subject to many different factors nature of the indoor propagation channel, it is easily concluded that both researchers in academia and engineers in industry need to have reliable models that will predict precisely the average path loss over the indoor 2.4 GHz channel which is of utter importance as the de facto frequency of Wi-Fi and WLAN systems. A gap in aforementioned research, however, is that it either concentrates on multipath parameters or does not feature a full comparative validation of most well-known indoor path loss models.The purpose of this work is to present, all the data collected through experiments in realistic conditions and real telecom systems, in order to validate and modify (where necessary) the existing RF models. Furthermore an empirical formula to measure attenuation due to shadowing is derived through these RF models.Measurements took part in five different topologies. In each of them the mean received power was recorded, for various distances between the transmitter and the receiver, in order for our endeavor to validate the RF models in question to be reliable. Through this procedure, RF models where examined towards each topology’s distinctive characteristics that reflect in quality and quantity all the attenuation mechanisms that affect the propagated signal.

The main purpose of this thesis is to test a communications solution for the second to largest refugee settlement in the world, Bidi Bidi. A solution where it is possible to inform the refugees with necessary information, for example that the water at a specific location is currently contaminated or that food is provided at another location. The idea is to use nRF24L01+ modules which operate in the 2.4 GHz frequency band and send information through various ways. This includes turning LEDs' on and off, sending text Strings and streaming audio. The results showed that the modules are too unreliable for a refugee settlement. They also showed that it is not possible to send other types' of data while streaming audio, but there could be workarounds. It is clear that more knowledge and further investigations are needed.

The purpose of this thesis was to investigate the feasibility of a wireless architectural approach for intra-vehicle communications. The current wired architecture was compared to a wireless approach based on three prominent wireless protocols, namely Bluetooth Low-Energy, Ultra Wide-Band, and 60 GHz Millimeter wave technology. The evaluation was focused on their potential use within the intra-vehicle domain, and judged by characterizing properties such as frequency, bandwidth utilization, and power efficiency. A theoretical study targeting the propagating behavior of electromagnetic waves was also involved. In particular, wireless behavior has been investigated both in general aspects as well as specifically aimed towards the intra-vehicle application. The theoretical study was then concluded and presented with a course of action regarding wireless connectivity. Beneficial design considerations, potentials and challenges were highlighted together with a discussion on the feasibility of a wireless architectural approach. Suggestions for future work and research have been given, which include further expansion of targeted protocols, alleviating the restricted security aspects, and extend the physical aspects onto more software based approaches.

Submitted by bruna ortiz (brunaortiz.f@gmail.com) on 2016-07-04T15:34:48Z No. of bitstreams: 1 Dissertação-Laura Michaella Batista Ribeiro.pdf: 5196443 bytes, checksum: 44f8d0ba69aa5d5fb4454331819feaa4 (MD5) / Approved for entry into archive by Divisão de Documentação/BC Biblioteca Central (ddbc@ufam.edu.br) on 2016-07-18T13:11:02Z (GMT) No. of bitstreams: 1 Dissertação-Laura Michaella Batista Ribeiro.pdf: 5196443 bytes, checksum: 44f8d0ba69aa5d5fb4454331819feaa4 (MD5) / Approved for entry into archive by Divisão de Documentação/BC Biblioteca Central (ddbc@ufam.edu.br) on 2016-07-18T13:25:46Z (GMT) No. of bitstreams: 1 Dissertação-Laura Michaella Batista Ribeiro.pdf: 5196443 bytes, checksum: 44f8d0ba69aa5d5fb4454331819feaa4 (MD5) / Made available in DSpace on 2016-07-18T13:25:46Z (GMT). No. of bitstreams: 1 Dissertação-Laura Michaella Batista Ribeiro.pdf: 5196443 bytes, checksum: 44f8d0ba69aa5d5fb4454331819feaa4 (MD5) Previous issue date: 2014-04-07 / CAPES - Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / With the significant utilization of the Wi-Fi networks as one of the main mass media and transmission of data, some problems of traffic reliability have been related and increasing day by day. The unplanned use of Access’ Points – AP, chained to the interferences resulting from coexistence of other technologies occupying the same frequency spectrum 2.4GHz, has constantly affected the performance of these networks. In order to propose a solution to interference’s problem between networks 802.11, this work describe an approach of attribution of channels based in many aspects such as received signal strength indicator, signal-to-noise ratio, link quality and channels overlap factor. This approach, named MFDCA (Multi-Factor Dynamic Channel Assignment) is composed by detection interferences modules, as well as selection and attribution of channels. The approach attributes in a dynamic way operation of channels in the networks 802.11, considering the characteristics noted in the spectral environment where which AP is inserted. The MFDCA was developed so that to operate in low cost of access points, as long as they withstand an installation of a firmware based in Linux. The results of the tests accomplished in a pilot network show that a MFDCA is able to benefit the network as a whole, including non-administered networks, by increasing its throughput and decreasing the rate losses of packages. / Com a utilização significativa das redes Wi-Fi como um dos principais meios de comunicação e transmissão de dados, problemas relacionados à confiabilidade no tráfego dessas redes foram surgindo. O uso não planejado de pontos de acesso (do inglês, Access Point - AP), aliado com as interferências decorrentes da coexistência de outras tecnologias compartilhando o mesmo espectro de frequências 2,4GHz, tem constantemente afetado o desempenho das redes sem fio. Com o intuito de propor uma solução para o problema de interferência entre redes sem fio 802.11, este trabalho descreve uma abordagem para atribuição de canais baseada em múltiplos fatores como a indicação da intensidade do sinal recebido, a relação sinal-ruído, a qualidade de link e o fator de sobreposição de canais. Esta abordagem, denominada de MFDCA (Multi-Factor Dynamic Channel Assignment) é composta pelos módulos de detecção de interferências e de seleção e atribuição de canais. A abordagem atribui de forma dinâmica canais de operação nas redes 802.11, considerando as características presentes no ambiente espectral onde cada AP está inserido. AMFDCA foi projetada para operar em pontos de acesso de baixo custo, desde que suportem a instalação de um firmware baseado em Linux. Os resultados dos testes realizados em uma rede piloto mostram que a MFDCA é capaz de beneficiar as redes como um todo, incluindo redes não administradas, proporcionando um aumento na vazão de dados e a diminuição das taxas de perdas de pacotes.

Récemment la bande 60 GHz a été mise en avant pour le développement des réseaux de communication sans fil centrés sur le corps humain. Cet intérêt de la bande 60 GHz pour les applications BAN (Body Area Network) s'explique par les avantages clefs qu'elle procure par rapport aux bandes de fréquence plus basses (possibilité de débits de données supérieurs à 7 Gbit/s, réduction des interférences avec les réseaux voisin, compacité des dispositifs, etc). Le nombre d'application de communication BAN est amené à croître dans les années à venir avec le déploiement de la 5ème génération de réseaux de télécommunications mobiles. Afin de protéger efficacement les utilisateurs des expositions générées par ces applications BAN à 60 GHz, il est nécessaire de se pencher sur les problématiques de réduction du couplage corps/antennes, mais également sur l'évaluation et la quantification du niveau d'exposition du corps à 60 GHz. Pour cela, les travaux de thèse ont été organisés suivant trois axes de recherche : le premier consiste à mettre en évidence et à quantifier l'impact de certains choix de conception en matière d'antennes sur le couplage avec le corps humain ; le second porte sur les outils et les méthodes utilisés pour estimer l'impact thermique d'une exposition électromagnétique 60 GHz sur le fantôme équivalent de la peau ; et le troisième propose une nouvelle approche à la fois dosimétrique et thermique pour évaluer et analyser le couplage corps/antennes en bande millimétrique. / The 60-GHz frequency band has been identified recently as attractive for body centric wireless communication development. Indeed, this band has several key advantages compared to lower frequency bands as high data rates above 7 Gbit/s, low risks of interference with neighboring wireless networks and compact devices. With the development of the future 5th generation of mobile networks in the millimeter-wave band, the number of BAN applications at 60 GHz should increase. To avoid health effects and protect user against an electromagnetic exposure of BAN devices at 60 GHz, the reduction of the coupling between human body and antennas, as well as the evaluation and quantification of exposure are main research aspect of the thesis. The main thesis contributions are divided in three parts: a quantification of antenna design effects on the interactions between human body and antennas; a study of tools and methods used to assess thermal effects due to 60 GHz exposure on a skin-equivalent phantom; and a new dosimetric and thermal approach to evaluate interaction between human body and BAN antennas at 60 GHz.

The primary reason for the wireless technology evolution is towards building capacity and obtaining higher data rates. Enclosed locations, densely populated campus, indoor offices, and device-to-device communication will require radios that need to operate at data rates up to 10 Gbps. In the next few years, a new generation of communication systems would emerge to better handle the ever-increasing demand for much wider bandwidth requirements. Simultaneously, key factors such as size, cost, and energy consumption play a distinctive role towards shaping the success of future wireless technologies. In the perspective of 3GPP 5G next generation wireless communication systems, the X band was explicitly targeted with a vast range of applications in point to point radio, point to multi point radio, test equipment, sensors and future wireless communication. An X-band RF front-end circuit for next generation wireless network applications is presented in this work. It details the design of a low noise amplifier and a power amplifier for X band operation. The designed amplifiers were integrated with a wideband single-pole-double-throw switch to achieve an overall front-end structure for 10 GHz. The design was carried out and sent for fabrication using a GaN 0.15µm process provided by NRC, a novel design kit. Due to higher breakdown voltage, high power density, high efficiency, high linearity and better noise performance, GaN HEMTs are a suitable choice for future wireless communication. Thus, the assumption is to further explore capabilities of this process in front-end design for future wireless communications.

This thesis describes environmental data collection and transmission from the field to a server using Wi-Fi. Also discussed are components, radio wave propagation, received power calculations, and throughput tests. Measured receive power resulted close to calculated and simulated values. Throughput tests resulted satisfactory. The thesis provides detailed systematic procedures for Wi-Fi radio link setup and techniques to optimize the quality of a radio link.

This work deals with the study of Yagi-Uda antennas, followed by analysis and design of planar antenna with wired reflector. The first part focused on the analysis of the antenna and parameters. Another part of the continuing investigation of the optimum parameters for a given antenna followed by a design in Wi-Fi 5 GHz band. The antenna is simulated in CST Microwave Studio. The final part devoted the results achieved