No description available.

Real-time monitoring of vehicle data during testingcan drastically cut down on test times as well as improve thequality of testing by facilitating the implementation of run-timecompliance verification with expected model behavior, along withanomaly detection in both hardware and software. By providinga wireless communication link between vehicles and a monitoringbase station, this project aims to build the groundwork formore sophisticated testing proceedings in the future. The wirelesscommunication system implemented in this project mirrors datafrom the two CAN data busses on the vehicle and transmits themvia a licence-free 868 MHz ISM band. The receiver is connectedto a computer where the data can be visualized and analyzed inreal-time. The project goals were exceeded in both throughputand range. Early testing has shown that data rates of 150 kbit/sand ranges 1.2 km and beyond are achievable. The project has seta solid foundation upon which wireless testing routines can nowbe developed. Hardware and software developed in this projectcan be built upon and optimized further in future revisions toachieve even higher data rates and longer ranges. / Övervakning av fordonsdata i realtid undertestprocessen kan drastiskt dra ner på testtiden samt förbättrakvalitén av testerna genom att öppna upp möjligheten för verifieringav både hårdvara och mjukvara under körning. Genomatt skapa en trådlös kommunikationslänk mellan fordon och enövervakande basstation siktar det här projektet mot att läggagrunden för mer sofistikerade testmöjligheter i framtiden. Denimplementerade trådlösa kommunikationslänken speglar datafrån fordonets två CAN-databussar och sänder de över eterntill en radiomottagare. Sändningen sker via ett licensfritt 868MHz ISM band. På mottagarsidan kan datan sen visualiserasoch analyseras på en dator kopplad till mottagaren. Projektetsmål har överskridits både i datahastighet och räckvidd. Tidigatester har visat att datahastigheter på 150 kbit/s samt räckvidderpå över 1.2 km går att uppnå. Projektet har lagt en stabil grundför hur trådlös testrutin kan implementeras. Hårdvaran ochmjukvaran utvecklad i detta projekt kan byggas på och optimerasytterligare för framtida revisioner. Detta kan öppna upp för ännuhögre datahastigheter och räckvidder. / Kandidatexjobb i elektroteknik 2021, KTH, Stockholm

The increasing demand for high data rate devices and many applications in short range high speed communication, attract many RF IC designers to work on 24-GHz transceiver design. The Federal Communication Commission (FCC) also dedicates the unlicensed 24-GHz band for industrial, science, and medical applications to overcome the interference in overcrowded communications and have higher output signal power. LNA is the first building of the receiver and is a very critical building block for the overall receiver performance. The total NF and sensitivity of the receiver mainly depends on the LNAs NF that mandates a very low NF LNA design. Depending on its gain, the noise figure of the next stages can relax. However, the high gain of an LNA enforces the next stages to be more linear since they suffer from larger signal at their input stage and can get saturated easily. Apparently, designing high gain, low noise, and highly linear LNA is very stimulating. In this thesis, a wideband LNA with low noise figure and high linearity has been designed in 8XP 0.13-um SiGe BiCMOS IBM technology. The highlight of this design is proposing the peaking technique, which results in considerable linearity improvement. Loading the LNA with class AB amplifier, power gain experiences a peaking in high input signal swing levels. The next stager after the LNA is the buffer to provide isolation between the LNA and mixer, and also avoid loading of the LNA from the mixer. Instead of using popular emitter follower architecture, another circuit is proposed to have higher gain and linearity. This buffer has two separate out of phase inputs, coming from the LNA and are combined constructively at the output of the buffer. Since the frequency of this design is high, electromagnetic (EM) simulation for pads, interconnects, transmission lines, inductors, and coplanar transmission lines has been completed using Sonnet cad tool to consider all the parasitic and coupling effects. Considering all the EM effects, the LNA has 15 dB gain with 2.9 dB NF and -8.8 dBm input 1-dB compression point. The designed LNA is wideband, covering the frequency range of 12-GHz to 31-GHz. However, the designed LNA, has the capability of having higher gain at the expense of lower linearity and narrower frequency band using different control voltage. As an example peak gain of 29.3 dB at the 3-dB frequency range of 23.8 to 25.8-GHz can be achieved, having 2.3 dB noise figure and -17 dBm linearity. / Master of Science

In the push for spectrum sharing and open spectrum access, the 3.5 GHz frequency band is under consideration for small cells and general Wireless Local Area Networks (WLAN) in the United States. The same band is beginning to see deployment in China, Japan, and South Korea, for the 4G Long Term Evolution (LTE) cellular standard to increase coverage and capacity in urban areas through small cell deployment. However, since the adoption of this band is new, there is a distinct shortage of propagation data and accurate channel modeling at 3.5 GHz in indoor environments. These models are necessary for cellular coverage planning and evaluating the performance and feasibility of wireless systems. This report presents the results of a fixed wireless channel measurement campaign at 3.5 GHz. Measurements were taken in environments typical of indoor wireless deployment: traditional urban indoor office, hallway, classroom, computer laboratory, and atrium areas, as well as within a hospital. Primarily Non Line of Sight (NLOS) experiments were carried out in areas with a controllable amount of partitions separating the transmitter and receiver in order to document material-based attenuation values. Indoor-to-outdoor measurements were carried out, focusing on attenuation due to common exterior building materials such as concrete, brick, wood, and reinforced glass. Documented metrics include large scale path loss, log-normal shadowing, and channel power delay profiles combined with delay spread characteristics for multipath analysis. The statistical multi-antenna diversity gain was evaluated to gauge the benefit of using multi-antenna systems in an indoor environment, which has much greater spatial diversity than an outdoor environment. Measurements were compared to indoor path loss models used for WLAN planning in the low GHz range to investigate the applicability of extending these models to 3.5 GHz. / Master of Science

In recent years, advancements in the field of wireless communication have led to more innovative consumer products at reduced cost. Over the next 2 to 5 years, short-range wireless devices such as Bluetooth and Wireless Local Area Networks (WLANs) are expected to become widespread throughout hospital environments for various applications. Consequently the medical community views wireless applications as ineludible and necessary. However, currently there exist regulations on the use of wireless devices in hospitals, and with the ever increasing wireless personal applications, there will be more unconscious wireless devices entering and operating in hospitals. It is feared that these wireless devices may cause electromagnetic interference that could alter the operation of medical equipment and negatively impact patient care. Additionally, unintentional electromagnetic radiation from medical equipment may have a detrimental effect on the quality of service (QoS) of these short-range wireless devices. Unfortunately, little is known about the impact of these short-range wireless devices on medical equipment and in turn the interference caused to these wireless devices by the hospital environment. The objective of this research was to design and develop an automated software reconfigurable measurement system (PRISM) to characterize the electromagnetic environment (EME) in hospitals. The portable measurement system has the flexibility to characterize a wide range of non-contiguous frequency bands and can be monitored from a remote location via the internet. In this work electromagnetic interference (EMI) measurements in the 2.4 GHz ISM band were performed in two hospitals. These measurements are considered to be very first effort to analyze the 2.4 GHz ISM band in hospitals. Though the recorded EMI levels were well within the immunity level recommended by the FDA, it can be expected that Bluetooth devices will undergo a throughput reduction in the presence of major interferers such as WLANs and microwave ovens. A Bluetooth throughput simulator using semi-analytic results was developed as part of this work. PRISM and the Bluetooth simulator were used to predict the throughput for six Bluetooth Asynchronous Connectionless (ACL) transmissions as a function of piconet size and interferer distance. / Master of Science

There has been increased interest in exploring high frequency (mm-wave) spectrum (particularly the 30 and 60 GHz ranges), and utilizing silicon-based technology for reduced-cost monolithic millimeter integrated circuits (MMIC), for applications such as WLAN, inter-vehicle communication (IVC) automotive radar and local multipoint distribution system (LMDS). Although there has been a significant increase in silicon-based implementations recently, this area still has significant need for research and development. For example, one microwave/mm-wave front-end component that has seen little development in silicon is the power amplifier (PA). Two potential technologies exist for providing a solution for low-cost microwave/mm-wave power amplifiers: 1) Silicon-Germanium (SiGe) HBT and 2) Complementary metal-oxide semiconductor (CMOS). SiGe HBT has become a viable candidate for PA development since it exhibits higher gain and higher breakdown voltage limits compared to CMOS, while remaining compatible with BiCMOS technology. Also, SiGe is potentially lower in cost compared to other compound semiconductor technologies that are currently used in power amplifier design. Hence, this research focuses on design of millimeter-wave power amplifiers in SiGe HBT technology. The work presented in this thesis will focus on design of different power amplifiers for millimeter-wave operating frequencies. Amplifiers present the fundamental trade-off between linearity and efficiency. Applications at frequencies highlighted above tend to be point-to-point, and hence high linearity is required at the cost of lowered efficiency for these power amplifiers. The designed power amplifiers are fully differential topologies based on finite ground coplanar waveguide (FGC) transmission line technology, and have on-chip matching networks and bias circuits. The selection and design of FGC lines is supported through full-wave EM simulations. Tuned single stub matching networks are realized using FGC technology and utilized for input and output matching networks. Two 30-GHz range SiGe HBT PA designs were carried out in Atmel SiGe2RF and IBM BiCMOS 8HP IC technologies. The designs were characterized first by simulations. The performance of the Atmel PA design was characterized using microwave/mm-wave on wafer test measurement setup. The IBM 8HP design is awaiting fabrication. The measured results indicated high linearity, targeted output power range, and expected efficiency performance were achieved. This validates the selection of SiGe HBT as the technology of choice of high frequency point-to-point applications. The results show that it is possible to design power amplifiers that can effectively work at millimeter-wave frequencies at lower cost for applications such as mm-wave WLAN and IVC where linearity is important and required transmitted power is much lower than in cellular handset power amplifiers. Moreover, recommendations are made for future research steps to improve upon the presented designs. / Master of Science

In 2001, the Federal Communications Commission made available a large block of spectrum known as the 60 GHz band. The 60 GHz band is attractive because it provides the opportunity of multi-Gbps data rates with unlicensed commercial use. One of the main challenges facing the use of this band is poor propagation characteristics including high path loss and strong attenuation due to oxygen absorption. Antenna arrays have been proposed as a means of combating these effects. This thesis provides an analysis of array processing for communication systems operating in the 60 GHz band. Based on measurement campaigns at 60 GHz, deterministic modeling of the channel through ray tracing is proposed. We conduct a site-specific study using ray tracing to model an outdoor and an indoor environment on the Virginia Tech campus. Because arrays are required for antenna gain and adaptability, we explore the use of arrays as a form of equalization in the presence of channel-induced intersymbol interference. The first contribution of this thesis is to establish the expected performance achieved by arrays in the outdoor environment. The second contribution is to analyze the performance of adaptive algorithms applied to array processing in mobile indoor and outdoor environments. / Master of Science

In 1997 the Federal Communications Commission (FCC) released 300 MHz of spectrum between 5-6 GHz designated the unlicensed national information infrastructure (U-NII) band. The intention of the FCC was to provide an unlicensed band of frequencies that would enable high-speed wireless local area networks (WLANs) and facilitate wireless access to the national information infrastructure with a minimum interference to other devices. Currently, there is a lack of cost-effective technologies for developing U-NII band components. With the commercial market placing emphasis on low cost, low power, and highly integrated implementations of RF circuitry, alternatives to the large and expensive distributed element components historically used at these frequencies are needed. Silicon Germanium (SiGe) BiCMOS technology represents one possible solution to this problem. The SiGe BiCMOS process has the potential for low cost since it leverages mature Si process technologies and can use existing Si fabrication infrastructure. In addition, SiGe BiCMOS processes offer excellent high frequency performance through the use of SiGe heterojunction bipolar transistors (HBTs), while coexisting Si CMOS offers compatibility with digital circuitry for high level 'system-on-a-chip' integration. The work presented in this thesis focuses on the development of a SiGe RFIC front-end for operation in the U-NII bands. Specifically, three variants of a packaged low noise amplifier (LNA) and a packaged active x2 sub-harmonic mixer (SHM) have been designed, simulated and measured. The fabrication of the Rifts was through the IBM SiGe foundry; the packaging was performed by RF Micro devices. The mixer and LNA designs were fabricated on separate die, packaged individually, and on-chip matched to a 50 ohm system so they could be fully characterized. Measurements were facilitated in a coaxial system using standard FR4 printed circuit boards. The LNA designs use a single stage, cascoded topology. The input ports are impedance matched using inductive emitter degeneration through bondwires to ground. One version of the LNA uses an shunt inductor/series capacitor output match while the other two variation use a series inductor output match. Gain, isolation, match, linearity and noise figure (NF) were used to characterize the performance of the LNAs in the 5 - 6 GHz frequency band. The best LNA design has a maximum gain of 9 dB, an input VSWR between 1.6:1 and 2:1, an output match between 1.7:1 and 3.6:1, a NF better than 3.9 dB and an input intercept point (IIP3) greater than 5.4 dBm. The LNA operates from a 3.3 V supply voltage and consumes 4 mA of current. The SHM is an active, double-balance mixer that achieves x2 sub-harmonic mixing through two quadrature (I/Q) driven, stacked Gilbert-cell switching stages. Single-ended-to-differential conversion, buffering and I/Q phase separation of the LO signal are integrated on-chip. Measurements were performed to find the optimal operating range for the mixer, and the mixer was characterized under these sets of conditions. It was found that the optimal performance of the mixer occurs at an IF of 250-450 MHz and an LO power of -5 dBm. Under these conditions, the mixer has a measured conversion gain of 9.3 dB, a P_1-dB of -15.7 dBm and an 2LO/RF isolation greater than 35 dB at 5.25 GHz. At 5.775 GHz, the conversion gain is 7.7 dB, the P_1-dB is -15.0 dBm, and the isolation is greater than 35 dB. The mixer core consumes 9.5 mA from a 5.0 V supply voltage. This work is sponsored by RF Microdevices (RFMD)through the CWT affiliate program.The author was supported under a Bradley Foundation fellowship. / Master of Science

In this modern age of information, the demands on data transmission networks for greater capacity, and mobile accessibility are increasing drastically. The increasing demand for mobile access is evidenced by the proliferation of wireless systems such as mobile phone networks and wireless local area networks (WLANs). The frequency range over which an oxygen resonance occurs in the atmosphere (~58-62 GHz) has received recent attention as a possible candidate for secure high-speed wireless data networks with a potentially high degree of frequency reuse. A significant challenge in implementing data networks at 60 GHz is the manufacture of low-cost RF transceivers capable of satisfying the system requirements. In order to produce transceivers that meet the additional demands of high-volume, mobility, and compactness, monolithic millimeter wave integrated circuits (MMICs) offer the most practical solution. In the design of radio tranceivers with a high degree of integration, the receiver front-end is typically the most critical component to overall system performance. High-performance low-noise amplifiers (LNAs) are now realizable at frequencies in excess of 100 GHz, and a wide variety of mixer topologies are available that are capable of downconversion from 60 GHz. However, local oscillators (LOs) capable of providing adequate output power at mm-wave frequencies remain bulky and expensive. There are several techniques that allow the use of a lower frequency microwave LO to achieve the same RF downconversion. One of these is to employ a subharmonic mixer. In this case, a lower frequency LO is applied and the RF mixes with a harmonic multiple of the LO signal to produce the desired intermediate frequency (IF). The work presented in this thesis will focus on the development of a GaAs MMIC 4-X subharmonic mixer in Finite Ground Coplanar (FGC) technology for operation at 60 GHz. The mixer topology is based on an antiparallel Schottky diode pair. A discussion of the mechanisms behind the operation of this circuit and the methods of practical implementation is presented. The FGC transmission lines and passive tuning structures used in mixer implementation are characterized with full-wave electromagnetic simulation software and 2-port vector network analyzer measurements. A characterization of mixer performance is obtained through simulations and measurement. The viability of this circuit as an alternative to other high-frequency downconversion schemes is discussed. The performance of the actual fabricated MMIC is presented and compared to currently available 60 GHz mixers. One particular MMIC design exhibits an 11.3 dB conversion loss at an RF of 58.5 GHz, an LO frequency of 14.0 GHz, and an IF of 2.5 GHz. This represents excellent performance for a 4X Schottky diode mixer at these frequencies. Finally, recommendations toward future research directions in this area are made. / Master of Science

Yes / To support various fifth generation (5G) wireless applications, a small, printed bowtie-shaped microstrip antenna with meandered arms is reported in this article. Because it spans the broad legal range, the developed antenna can serve or reject a variety of applications such as wireless fidelity (Wi-Fi), sub-6 GHz, and ultra-wideband (UWB) 5G communications due to its multiband characterization and optimized rejection bands. The antenna is built on an FR-4 substrate and powered via a 50-Ω microstrip feed line linked to the right bowtie’s side. The bowtie’s left side is coupled via a shorting pin to a partial ground at the antenna’s back side. A gradually increasing meandering microstrip line is connected to both sides of the bowtie to enhance the rejection and operating bands. The designed antenna has seven operating frequency bands of (2.43–3.03) GHz, (3.71–4.23) GHz, (4.76–5.38) GHz, (5.83–6.54) GHz, (6.85–7.44) GHz, (7.56–8.01) GHz, and (9.27–13.88) GHz. The simulated scattering parameter S11 reveals six rejection bands with percentage bandwidths of 33.87%, 15.73%, 11.71, 7.63%, 6.99%, and 12.22%, respectively. The maximum gain of the proposed antenna is 4.46 dB. The suggested antenna has been built, and the simulation and measurement results are very similar. The reported antenna is expanded to a four-element design to investigate its MIMO characteristics. / Partially funded by British Council “2019 UK-China-BRI Countries Partnership Initiative” program, with project titled “Adapting to Industry 4.0 oriented International Education and Research Collaboration.