Made available in DSpace on 2016-06-02T19:56:59Z (GMT). No. of bitstreams: 1 6783.pdf: 3853594 bytes, checksum: 5c76462cb2ede47f0f6638372f3f2364 (MD5) Previous issue date: 2015-02-18 / Financiadora de Estudos e Projetos / The fluid catalytic cracking (FCC) is one of the most important process in the petroleum refining industry, being responsible for the increase of the yield of the most valuable light hydrocarbons. On the other hand, the FCC process generates big amounts of CO, NOx and SOx emissions. The CO emissions from the most of pollution sources are abatement using noble metal based catalysts. However, the growing demand and scarcity of those metals have caused an increase in the process cost and consequently promoting studies to find alternative catalysts with comparable efficiency and lower in cost. In this respect, the literature had presented interesting results with transitions metal catalysts. Thus, the objective of this work was to prepare exchanged or impregnated Fe or Mn on H-mordenite or Ce-mordenite, which were evaluated between 150 and 550 oC in the CO oxidation with O2, in the presence or absence of interfering compounds (water steam or SO2). The catalysts were characterized by ICP-OES, DRX, DRS-UV-VIS and Mössbauer spectroscopy. The results showed that the preparation procedures of the interchanged or impregnated Fe or Mn catalysts were adequate, and no mordenite crystallinity loss was observed. Contrary to the exchanged Fe or Mn based catalysts, those based on impregnated Fe or Mn oxides showed a important potential as catalysts in the CO oxidation with O2. Then, in the applied operational conditions the Ce-MOR/Fe10, Ce-MOR/Mn5, Ce-MOR/Mn10 e H-MOR/Mn5 catalysts were able to produce an effluent with CO content lower than 500 ppm, which is the allowed limit by the environmental regulations related with FCC units. In the presence of water steam the evaluated Fe or Mn catalysts presented activity loss that was recovered after the elimination of that interfering from the feed. Nevertheless, in the presence of SO2, the tested catalysts showed an irreversible and significantly activity loss. / O craqueamento catalítico fluido (FCC) é uma das etapas mais importantes no refino de petróleo, sendo responsável pelo aumento do rendimento em frações leves, de maior valor agregado. Por outro lado, o FCC é responsável na refinaria por uma grande parcela das emissões de monóxido de carbono (CO), óxidos de nitrogênio (NOx) e óxidos de enxofre (SOx). O CO, em particular, na maioria das fontes poluidoras é eliminado via oxidação sobre catalisadores à base de metais nobres. Porém, o aumento na demanda desses metais e sua baixa disponibilidade criam um forte impacto no custo do processo, surgindo a necessidade de buscar catalisadores alternativos, com eficiência comparável e de menor custo. Assim, o objetivo deste trabalho foi preparar catalisadores à base de ferro ou manganês impregnados ou trocados em H-mordenita ou Ce-mordenita e avaliá-los entre 150 e 550 oC na oxidação de CO com oxigênio (O2), na ausência ou presença de compostos interferentes à reação como vapor de água e dióxido de enxofre (SO2). Os catalisadores foram caracterizados por espectroscopia de emissão atômica (ICP-OES), difração de raios X (DRX), espectroscopia de reflectância difusa (DRS-UV-VIS), redução com H2 à temperatura programada (RTP-H2) e espectroscopia Mössbauer (MOSS). Os resultados mostraram que os procedimentos de preparação dos catalisadores, trocados ou suportados, foram eficientes, não se observando perda de cristalinidade da mordenita. Os catalisadores com óxidos de Fe ou Mn suportados na mordenita apresentaram um importante potencial para serem utilizados como catalisadores na oxidação de CO com O2, contrário ao que ocorreu com cátions de Fe ou Mn em sítios de troca. Assim, nas condições operacionais utilizadas, os catalisadores Ce-MOR/Fe10, Ce-MOR/Mn5, Ce-MOR/Mn10 e H-MOR/Mn5 foram capazes de converter CO suficiente para produzir um efluente gasoso com teor menor que 500 ppm de CO, sendo essa a concentração limite permitida pela legislação que rege as emissões de unidades FCC. Os catalisadores impregnados com Fe e Mn, quando avaliados na presença de vapor de água e de SO2, ocorreu perda da atividade, a que foi recuperada somente no caso do vapor de água.

Conselho Nacional de Desenvolvimento Científico e Tecnológico / In this study we investigated the interaction between lead and the amino acid cysteine, lysine and N-acetylcysteine by testing long-term contact with ion exchanger resins and also the determination of stability constants. The importance of investigating the presence of lead in solutions for parenteral nutrition is related to the risk of internal contamination of these solutions due to the affinity between amino acids that compose these solutions and lead present in plastic packaging. The amino acids according to their relative affinities can act as carriers of metal in living organisms. The long term tests with adsorbents in form of Pb2+ showed that the higher extraction of lead occurs at amino acid that has a greater affinity for the metal and this is evidenced by the value of stability constant calculated, i.e., there was a direct relationship of the values of the calculated stability constants. Kinetic effects were not significant in this study, since the trials were of long duration. Tests with complexing agents such as EDTA and citric acid, that have known stability constants, were also performed for comparison purposes. The quantification of lead in long term tests was performed by atomic absorption spectrometry with flame and electrothermal atomization. The stability constants were obtained by potentiometry by processing the data through the software BEST®. Titrations in aqueous solutions with constant ionic strength and temperature showed that the predominant species in solution have molar ratio of 1:1 (L: M) to N-acetyl-cysteine and lysine and 1:1 and 2:1 for cysteine. The main species found for cysteine were Cys2Pb and CysPbOH with log K = 1.61 and 24.00, respectively, for N-acetylcysteine N-Acetyl-Cys2Pb, N-Acetyl-Cys2PbH and N-Acetyl-CysPbOH with log K =-1.55, 14.52 and 21.49 respectively, and for lysine LysPb with log K = 9.69. The interaction of amino acids studied with lead was also detected by the tests made with the raw material of the packaging of parenteral nutrition solutions through the analysis by AAS. / Neste trabalho investigou-se a interação entre chumbo e os aminoácidos cisteína, N-acetilcisteína e lisina por meio de ensaios de contato de longa duração com resina de troca iônica e estudos para determinar as constantes de estabilidade dos complexos formados entre eles. A importância de investigar a presença de chumbo em soluções de nutrição parenteral relaciona-se ao risco de contaminação interna destas soluções em decorrência da afinidade entre os aminoácidos que compõem as soluções e o chumbo presente nas embalagens plásticas. Os aminoácidos em função de suas afinidades relativas podem atuar como transportadores do metal nos organismos vivos. Os resultados dos ensaios de contato com resina na forma Pb2+ mostraram que a maior extração do chumbo ocorre pelo aminoácido que possui maior afinidade pelo metal e isto é comprovado pelo valor da constante de estabilidade calculada, ou seja, houve relação direta dos valores das constantes obtidas através do cálculo das mesmas para os aminoácidos estudados com a taxa de extração do chumbo da resina pelos ligantes (aminoácidos). O efeito cinético, estabelecido pelas leis de velocidades não importaram nesse estudo, uma vez que os ensaios foram de longa duração. Ensaios com agentes complexantes, como EDTA e ácido cítrico, com constantes de estabilidade já conhecidas, também foram realizados para fins comparativos. A quantificação de chumbo nos ensaios de longa duração foi realizada por espectrometria de absorção atômica (AAS) com atomizações por chama e eletrotérmica. As constantes de estabilidade foram obtidas por potenciometria com o tratamento dos dados através do programa computacional BEST®. Titulações potenciométricas, de soluções aquosas com força iônica e temperatura constantes, mostraram que as espécies predominantes em solução são de razão molar 1:1 (L:M) para N-acetilcisteína e lisina e de 1:1 e 2:1 para cisteína. As principais espécies encontradas foram para cisteína, Cys2Pb e CysPbOH com log K = 1,61 e 24,00 respectivamente, para N-acetilcisteína N-Acetil-Cys2Pb, N-Acetil-Cys2PbH e N-Acetil-CysPbOH, com log K = -1,55; 14,52 e 21,49 respectivamente, e para lisina LysPb, com log K = 9,69. A interação dos aminoácidos estudados com o chumbo também foi constatada pelos ensaios feitos com a matéria-prima das embalagens das soluções de Nutrição Parenteral através da análise por AAS.

A invertase comercial (Bioinvert®) foi imobilizada por adsorção em resinas aniônicas do tipo Dowex® [1x8:50-400, 1x4:50-400 e 1x2:100-400, todos copolímeros estireno-divinilbenzênicos, porém de granulometria (50-400 mesh) e quantidades de ligações cruzadas diferentes (2-8%)] em meio aquoso. A melhor percentagem de adsorção da invertase nas resinas foi observada em pH 5,5 a 32°C, tendo o complexo Dowex®1x4-200/lnvertase apresentado índice de adsorção e coeficiente de imobilização iguais a 100%. Os parâmetros cinéticos e termodinâmicos foram determinados para a invertase solúvel e insolúvel de Bioinvert® e também para a invertase purificada (Fluka®). O complexo Dowex®1 x4-200/Bioinvert® apresentou-se estável durante as reações sem desprendimento da enzima do suporte. Os parâmetros termodinâmicos da forma solúvel e insolúvel da Fluka® foram idênticos aos do Bioinvert®, no entanto, após a imobilização apresentou uma redução de 28% na sua atividade. O estudo da atividade transferásica de ambas as formas de Bioinvert® em diferentes concentrações de sacarose foram analisadas através da cromatografia de camada delgada. A estabilidade operacional e de estocagem foi também determinada para o complexo Dowex®1x4-200/Bioinvert®. / The invertase (trademarked as Bioinvert®) solubilized in deionized water was immobilized by adsorption on anion exchange resins, collectively named Dowex®, [1x8:50-400, 1x4:50-400 and 1x2:100-400, styrene-divinylbenzene copolymers, with different granulometry (50-400mesh) and different degrees of cross-linking (2-8%)]. The best percentage of adsorption of invertase on resins was observed in pH 5.5 at 32°C and the complex Dowex®1x4-200/invertase has shown a coupling yield and an immobilization coefficient equal to 100%. The thermodynamic and kinetic parameters for sucrosehydrolysis for both soluble and insoluble enzyme were evaluated to Bioinvert® and purified invertase purchased from Fluka®. The complex Dowex®/Bioinvert® was stable without any desorption of enzyme from the support during the reaction and having the thermodynamic parameters equal to the soluble formo However, the loss of activity for immobilized Fluka® was found to be 28% when compared to the soluble one. The transfructosylating activity of Bioinvert® in both forms in different concentrations of sucrose was investigated through TLC. In regard to insoluble Bioinvert® its storage and operational stability were also determined.

A invertase comercial (Bioinvert®) foi imobilizada por adsorção em resinas aniônicas do tipo Dowex® [1x8:50-400, 1x4:50-400 e 1x2:100-400, todos copolímeros estireno-divinilbenzênicos, porém de granulometria (50-400 mesh) e quantidades de ligações cruzadas diferentes (2-8%)] em meio aquoso. A melhor percentagem de adsorção da invertase nas resinas foi observada em pH 5,5 a 32°C, tendo o complexo Dowex®1x4-200/lnvertase apresentado índice de adsorção e coeficiente de imobilização iguais a 100%. Os parâmetros cinéticos e termodinâmicos foram determinados para a invertase solúvel e insolúvel de Bioinvert® e também para a invertase purificada (Fluka®). O complexo Dowex®1 x4-200/Bioinvert® apresentou-se estável durante as reações sem desprendimento da enzima do suporte. Os parâmetros termodinâmicos da forma solúvel e insolúvel da Fluka® foram idênticos aos do Bioinvert®, no entanto, após a imobilização apresentou uma redução de 28% na sua atividade. O estudo da atividade transferásica de ambas as formas de Bioinvert® em diferentes concentrações de sacarose foram analisadas através da cromatografia de camada delgada. A estabilidade operacional e de estocagem foi também determinada para o complexo Dowex®1x4-200/Bioinvert®. / The invertase (trademarked as Bioinvert®) solubilized in deionized water was immobilized by adsorption on anion exchange resins, collectively named Dowex®, [1x8:50-400, 1x4:50-400 and 1x2:100-400, styrene-divinylbenzene copolymers, with different granulometry (50-400mesh) and different degrees of cross-linking (2-8%)]. The best percentage of adsorption of invertase on resins was observed in pH 5.5 at 32°C and the complex Dowex®1x4-200/invertase has shown a coupling yield and an immobilization coefficient equal to 100%. The thermodynamic and kinetic parameters for sucrosehydrolysis for both soluble and insoluble enzyme were evaluated to Bioinvert® and purified invertase purchased from Fluka®. The complex Dowex®/Bioinvert® was stable without any desorption of enzyme from the support during the reaction and having the thermodynamic parameters equal to the soluble formo However, the loss of activity for immobilized Fluka® was found to be 28% when compared to the soluble one. The transfructosylating activity of Bioinvert® in both forms in different concentrations of sucrose was investigated through TLC. In regard to insoluble Bioinvert® its storage and operational stability were also determined.

Le développement des technologies optiques dans le domaine de la communication engendre un intérêt pour les matériaux présentant des propriétés non linéaires. Le matériau idéal doit combiner un coefficient non linéaire élevé, de bonnes propriétés optiques et un faible coût de fabrication. Les matériaux vitreux restent de bons candidats pour ce type d’application. La polarisation thermique permet de générer ce genre de propriétés dans les verres. En effet, à des températures de l’ordre de 300°C, l’application d’un champ électrique provoque la migration d’ions mobiles dans le matériau depuis l’anode vers la cathode. Une zone de déplétion en surface est ainsi créée donnant naissance à un champ électrique enterré. En combinant une technique de dépôt métallique, une irradiation laser et l’application d’un champ électrique (poling), il devient possible de réaliser des architectures complexes de migration et d’obtenir ainsi des propriétés optiques non linéaires structurées. / Optical technologies development for communication has triggered a real interest about materials with nonlinear properties. The ideal material should combine a high nonlinear coefficient, good optical properties and a low production cost. Glasses remain very good materials for this kind of applications.Thermal poling is now well known for breaking glasses natural centro-symmetry and inducing second order nonlinearities. Indeed, at temperatures close to 300°C, the application of an electric field induces mobile ions migration from the anode to the cathode.In that case, the space charge created during the poling process generates an efficient macroscopic electrostatic field trapped under the anodic surface of the glass.The combination of silver deposition, femtosecond laser irradiation and thermal poling has been successfully used to realize a complex architecture of ionic migration leading to structuring of second order nonlinear properties at the microscopic scale.

Made available in DSpace on 2014-12-17T15:01:45Z (GMT). No. of bitstreams: 1 AndreaLF.pdf: 804797 bytes, checksum: e48b62b20831c2372981d6edcc8e4608 (MD5) Previous issue date: 2008-07-21 / The city of Natal comprises an area of about 170 km? (65,63 squares miles). The Dunas-Barreiras Aquifer is the most important reservoir of the coastal basin of RN. It is being responsible for the water supplying of about 70% of the population, however, due to the sewage disposal system by cesspools and drains, it is presently affected in a great extent by nitrates contamination. Thus, the present work proposes to research the utilization of contaminated water by nitrates of this fountainhead and find cost of the potable water through the ionic exchange technology. This technology consists in the removal of mineral salts by the exchange of cations for one ion of hydrogen (H+), through the passage of water by cationic resin bed and, secondly, by the exchange of the anions for hydroxyl ions (OH-) through a anionic resin bed. The obtained results have showed the waters derived from fountains, big water holes and shallow wells were microbiologically contaminated, while the waters derived from deep wells (above 70 m 76,58 yards) were free of contamination. Thus, only these ones are suitable to the use of ionic technology. The experiments were conducted with the resin IMAC-HP-555 such as kinetic, thermodynamic, and adsorption by fixed bed studies, being obtained several project variables for the experimental column, as follow: work temperature of 25oC; resin maximum capacity maximum e mean of adsorption ==0,01692 g NO3-1/g R e 0,0110 g NO3-1/g R, respectively. On the experimental column were performed breakthrough tests which pointed for an average ideal average speed of work of 13.2 m / h, with an average efficiency of 45% of adsorption, an optimal concentration of NaCl desorption of 8%, and an ideal desorption time of 80 minutes for the equilibrium conditions of water from the Dunas-Barreiras aquifer. Scale projection for ion-exchange column for denitrification, for these variables, using a computer modeling programme, to project the column of ion exchange ROREX-420/2000, obtained a cost for the drinking water denitrified by this system of R$ 0,16 / m3 / A cidade de Natal-RN abrange uma ?rea de aproximadamente 170 km2. O aq??fero Dunas-Barreiras, mais importante reservat?rio da bacia costeira do RN, abastece cerca de 70% da cidade. Devido ? aus?ncia de sistema de saneamento municipal e a cidade ter adotado forma de disposi??o de esgotos atrav?s de fossas e sumidouros, este aq??fero apresenta-se, em grande parte, contaminado por nitratos. O trabalho em quest?o se prop?e a pesquisar o aproveitamento da ?gua contaminada desse manancial, assim como estimar o custo da ?gua pot?vel atrav?s da tecnologia de troca i?nica. O estudo da qualidade das ?guas do aq??fero Dunas-Barreiras mostrou que, as ?guas provenientes de fontes, cacimbas e po?os rasos apresentaram-se contaminadas microbiologicamente, enquanto as ?guas provenientes de po?os profundos (superior a 70 m) apresentaram-se isentas, sendo ent?o somente essas adequadas para aproveitamento pela tecnologia de troca i?nica. Foram realizados v?rios experimentos cin?tico, termodin?mico, utilizando (resina IMAC-HP-555) o m?todo da imers?o em volume finito e din?micos da adsor??o por troca i?nica usando-se uma coluna. A partir destes resultados foi projetada uma coluna piloto onde se usou uma resina ani?nica, operando no ciclo cloreto, para remo??o seletiva de nitrato. Os resultados obtidos indicaram uma temperatura de trabalho de 25oC, velocidade m?dia ideal de trabalho de 13,6 m/h, capacidade de adsor??o m?xima e m?dia da resina =0,01692 g NO3-1/g R e 0,0110 g NO3-1/g R, respectivamente, concentra??o ideal de dessor??o do NaCl de 8% e tempo ideal de dessor??o de 80 minutos para as condi??es de equil?brio da ?gua do aq??fero Dunas-Barreiras. Experi?ncia de proje??o de aumento de escala realizada para sistema de coluna de troca i?nica para desnitrifica??o, com as vari?veis determinadas, adotou-se um programa de modelagem computacional para projetos de coluna de troca i?nica, ROREX-420/2000, onde se obteve um custo da ?gua pot?vel desnitrificada de R$ 0,16/m3. Para um volume de ?gua pot?vel produzido igual a 2.100 m3/ ciclo de opera??o foi obtida uma efici?ncia m?dia de remo??o de nitratos de 45%

Le nouvel essor industriel du marché des applications mobiles telles que les smartphones ou les tablettes tactiles nécessite de nombreuses recherches afin de concevoir des écrans en verres encore plus résistant. Le procédé d’échange ionique au potassium permet d’améliorer la résistance mécanique des verres grâce à la substitution des ions Na⁺ par des ions K⁺, de plus gros rayon ionique. Elle permet ainsi de bloquer les fissures superficielles du verre et de réduire la casse du matériau. Ce travail est consacré à comprendre le principe de diffusion des ions K⁺ au sein de la structure silicatée de différents verres. Les paramètres, temps, température et composition verrière, influent sur la cinétique de l’échange ionique. Dans les mêmes conditions de trempe, la réduction de la composition à un formateur et à l’ion mobile permet d’améliorer la diffusion et la propagation des ions au sein du matériau. Les conditions de trempe, thermique et temporelle, agissent sur la cinétique de diffusion des ions. Elles réduisent la facilité de déplacement des ions à travers la structure silicaté du matériau avec un changement de comportement au-delà de 8h d’immersion dans les sels fondus. La substitution des Na⁺ par les ions K⁺ et leur différence de taille modifient l’environnement des sites laissés vacants par les ions Na⁺ et modifie la structure silicatée du verre. La spectroscopie IR permet de mettre en évidence les modifications structurales des verres soumis à ce procédé d’échange ionique. Lors de l’introduction des ions K⁺, la structure du verre se dépolymérise et crée des oxygènes non pontants. Ceci permet de montrer que l’échange ionique conduit à l’amélioration du renforcement mécanique des verres. / The new industrial boom of the market for mobile applications such as smartphones or tablets requires much research in order to touch-screens design more resistant. The potassium ion exchange process improves the mechanical strength of glass by Na⁺ ions substitution with K⁺ ions, of larger ionic radius. It thus helps to block surface cracks in glass and reduce breakage of the material. This work is devoted to understand the principle of K⁺ diffusion in the silicate structure of different glasses. The parameters: time, temperature and glass composition affect the kinetic of ion exchange process. In the same quenching conditions, the limitation of the composition just to a former network and a mobile ion can improve the diffusion and the penetration ions inside the material. The quenching conditions, temperature and time, act on the kinetic diffusion. They reduce the mobility of the ions through the structure of the silicate material with a change of behaviour above 8h immersion in molten salts. Substitution of Na⁺ by K⁺ ions having different size affect the environment of the sites left vacant by the Na⁺ ions and modifies the silicate structure of the glass. IR spectroscopy allows highlighting the structural modifications of the glass submitted to this ion exchange process. During the introduction of the K⁺ ions inside the glass, the silicate structure is depolymerized and creates no-bridging oxygens. This allows to demonstrate that the ion exchange lead to the mechanical improvement of the glass.

Le but de ce travail de thèse est de contrôler via un traitement de polarisation les propriétés physico-chimiques de surface des verres. Pour cela, l'implémentation d'une charge d'espace au sein de différents verres silicates et borosilicates a été caractérisée. Ces études comparatives ont montré que la déplétion des cations de l’anode vers la cathode induit l’apparition d’un champ électrique et des modifications structurales localisées. De plus, nous avons démontré que la formation d’un plasma entre l’anode et le verre pouvait être à l’origine de phénomènes d'échanges ioniques conduisant notamment à la formation d’entités azotées NO2/N2O4 piégées dans le verre. Par la suite, une étude des propriétés physico-chimiques des surfaces polarisées a été conduite. Les résultats préliminaires obtenus concernent l'influence de la charge d'espace sur (i) la mouillabilité, (ii) la chimie de surface et (iii) les réponses optiques de molécules adsorbées. / The purpose of this work is to control physicochemical properties of glasses surfaces using a thermal polarization treatment. For this, the implementation of a space charge layer has been characterized for various silicates and borosilicates glasses. These comparative studies have shown that cations depletion from anode toward cathode induces both an electric field and structural local changes. To go further, we demonstrated that there is a plasma formation between anode and glass surfaces which could be the cause of ionic exchange phenomena leading to the formation of nitrogen NO2/N2O4 entities entrapped inside glass network. Subsequently, physicochemical properties studies of polarized surfaces were performed. Preliminary results concerning the space charge influence on (i) surface wettability, (ii) surface chemistry and (iii) optical responses of adsorbed molecules on poled glass surface have been obtained.