The need for highly efficient energy storage devices has been steadily increasing due to growing energy demands. Research in electrochemical energy storage in the form of batteries has consequently become crucial. Currently, the most commercialized battery technology is the lithium ion battery (LIB). Concerns over the relatively limited global lithium supply, however, have led to the development of sodium ion batteries (SIBs). Solid-state nuclear magnetic resonance (ssNMR) spectroscopy is an ideal technique for analyzing battery materials as it can potentially distinguish between different ions within the material. The most typical cathode for commercial LIBs are the family of NMC layered oxides with the general form Li[NixMnyCo1-x-y]O2, which consist of Li layers between sheets of transition metals (TMs). The pj-MATPASS NMR technique, in conjunction with Monte Carlo simulations, was applied to investigate the ionic arrangement within TM layers of NMC622 (Li[Ni0.6Mn0.2Co0.2]O2), which revealed the presence of ion clustering in the pristine form of this material. This thesis also investigated the promising SIB cathode, Na3V2(PO4)2F3 (NVPF). NVPF has the capability to produce energy densities comparable to those of LIBs and is well understood from a structural standpoint, however ion dynamics within the material are still undetermined. A series of materials have, therefore, been synthesized with the general form, Na3V2-xGax(PO4)2F3 (where x = 0, 1, and 2), where diamagnetic Ga3+ was introduced into the structure to enable the establishment of a structural correlation with observed Na-ion dynamics. It, therefore, became possible to explore ionic site exchange using 23Na ssNMR. Density functional theory (DFT) calculations have also been performed alongside ssNMR to confirm chemical shift assignments and provide structural insight. Additionally, electron paramagnetic resonance (EPR) spectroscopy was also used to investigate the paramagnetic nature of NVPF and its variants. Insights into the ionic arrangement and very fast Na-ion dynamics within these materials were revealed. / Thesis / Master of Science (MSc) / The need for highly efficient energy storage devices, especially in the form of batteries, has been steadily increasing due to growing energy demands. Presently, the most commercialized types of batteries are lithium ion batteries (LIBs). Concerns over the relatively limited global lithium supply, however, have led to the development of sodium ion battery (SIB) alternatives. Various solid-state nuclear magnetic resonance (ssNMR) techniques have been employed in this thesis to investigate both LIB and SIB cathode materials. The LIB cathode Li[Ni0.6Mn0.2Co0.2]O2 was examined with a combination of ssNMR and Monte Carlo simulations, and it was found that ion clustering occurs in the pristine form of these materials. The promising family of SIB cathodes, Na3V2-xGax(PO4)2F3, was studied by a combination of ssNMR, ab initio calculations, and EPR, which allowed for a correlation to be established between the crystal structure and the fast ion dynamics within these materials.

Die experimentellen Daten können bei Dr. Sebastian Risse, Helmholtz-Zentrum Berlin, eingesehen werden. / Silizium-Elektroden werden aufgrund ihrer um eine Gröÿenordnung höheren Kapazität als mögliches Elektrodenmaterial in Lithium-Ionen-Batterien betrachtet. Diese Kapazität geht jedoch mit einer Volumenausdehnung von bis zu 310 % einher. Dies begünstigt einen schnellen Kapazitätsabfall und ein kontinuierliches Wachstum der SEI-Schicht. Ziel dieser Arbeit ist es daher, die Morphologie-Änderung der Siliziumelektrode während des Lithiierungs-Prozesses besser zu verstehen unter Nutzung von operando-Methoden Im ersten Teil wurde Neutronenreflektometrie (NR) genutzt, um die Morphologie-Änderung auf der Nanometerskala einer Siliziumelektrode zu untersuchen. Das Wachsen/Schrumpfen der lithiierten Zone im Silizium wurde beobachtet. Auf der Oberfläche der Elektrode wächst im delithiierten Zustand eine Grenzschicht, welche die Lithiierung verhindert. Nachdem diese Schicht aufgelöst ist, kann Lithium eingelagert werden. Im zweiten Teil wurde operando Röntgen- Phasenkontrast-Radiographie genutzt. Ein rechteckiges Riss-Gitter wurde dabei im delithiierten Zustand beobachtet, welches sich während der Lithiierung schließt. Dieses Gitter ist entlang der Kristallachsen des Siliziums orientiert. Im nächsten Zyklus entsteht das Gitter am selben Ort wieder, und breitet sich mit steigender Zyklenzahl über die Elektrode aus. Im dritten Teil wurde der Einfluss einer künstlichen Grenzschicht auf die Lithiierung untersucht. Erneut wurde NR genutzt. Die künstliche Schicht verringert das Wachstum der SEI-Schicht, unterdrückt es jedoch nicht komplett. Nach 2 Zyklen ist die Grenzschicht degradiert, und Seitenreaktionen können beobachtet werden. / Silicon electrodes receive great interest as potential electrode material in lithium-based batteries due to their one order of magnitude higher capacity. This is accompanied by a volume expansion of up to 310 %, leading to an accelerated capacity loss of the electrodes. The volume expansion creates mechanical stress, leading to fracturization of the electrode and the continuous growth of the solid-electrolyte-interphase (SEI) layer under the consumption of active material. The aim of this thesis is to investigate the morphological changes of silicon electrodes during lithiation/ delithiation. Especially operando-techniques are well-suited to investigate these morphological changes since they allow us to precisely link structural data and the electrochemical state. The first project uses operando neutron reflectometry (NR) and in-situ electrochemical impedance spectroscopy (EIS) to analyze the morphology change of the silicon surface on the nanometer-scale. The growth and shrinkage of the lithiated layers within the electrode as well as the lithium concentration was determined with this method. An SEI-layer forms on top of the silicon electrode in the delithiated state, which hinders the lithium uptake in the initial part of the subsequent lithiation. The second project analyzes the morphology-change of the electrode on the µm-scale. Here the fracturization of the silicon electrode is investigated by operando X-ray phase-contrast radiography. A rectangular fracturization pattern was observed during the second half of the delithiation, which vanished again during the lithiation. The third project investigates the influence of an artificial coating layer on the lithiation process. Again operando NR was chosen as analysis tool. The artificial coating decreased the formation of the SEI-layer within the first cycles, but did not suppress it completely. However, this layer degraded already in an early stage of cycling, resulting in the occurrence of side reactions afterward.

<p dir="ltr">Direct recycling of cathode materials from spent Li-ion batteries (LIBs) or electrode scraps necessitates efficiently recovering valuable active materials from the aluminum foil. The variability in electrode types and recovery processes across previous studies complicates the comparative assessment of the recovery performance of green solvents. Furthermore, constant requirements of high temperature during recovery and impurities retained on the active material surface inhibit the progress to full-scale commercialization. In this study, we evaluated the performance of three green solvents—triethyl phosphate (TEP), dihydrolevoglucosenone (Cyrene), and propylene carbonate (PC)—in recovering valuable active materials from industrial-grade cathode scraps. Using ultrasonication, we developed a standardized, energy-efficient recovery process that eliminated the need for conventional stirring and achieved complete cathode delamination from the aluminum foil. Additionally, solvent washing was implemented on recovered active materials for impurity removal to achieve competitive electrochemical performance. Furthermore, we successfully recovered the used green solvents after the process, ensuring their reuse and supporting a circular economy. The recovered materials retained their original morphology, chemical composition, and crystalline structure; however, the presence of surface impurities varied significantly depending on the choice of green solvent. These impurities considerably impacted the electrochemical performance of the recovered materials. TEP and PC yielded high-purity active materials and aluminum foils suitable for reuse or direct recycling, while Cyrene resulted in substantial residues of PVDF/solvent, requiring washing with stronger solutions such as reagent alcohol. Additionally, the recyclability of these green solvents was influenced by their solubility power for PVDF. This study provides valuable insights into the green solvent-based recycling process and the importance of post-recovery washing steps laying the groundwork for future sustainable practices in LIB recycling.</p>

Lithium ion batteries (LIBs) have attracted considerable interest due to their wide range of applications, such as portable electronics, electric vehicles (EVs) and aerospace applications. Particularly, the emergence of a variety of nanostructured materials has driven the development of LIBs towards the next generation, which is featured with high specific energy and large power density. Herein, rolled-up nanotechnology is introduced for the design of strain-released materials as anodes of LIBs. Upon this approach, self-rolled nanostructures can be elegantly combined with different functional materials and form a tubular shape by relaxing the intrinsic strain, thus allowing for enhanced tolerance towards stress cracking. In addition, the hollow tube center efficiently facilitates electrolyte mass flow and accommodates volume variation during cycling. In this context, such structures are promising candidates for electrode materials of LIBs to potentially address their intrinsic issues. This work focuses on the development of superior structures of Si and SnO2 for LIBs based on the rolled-up nanotech. Specifically, Si is the most promising substitute for graphite anodes due to its abundance and high theoretical gravimetric capacity. Combined with the C material, a Si/C self-wound nanomembrane structure is firstly realized. Benefiting from a strain-released tubular shape, the bilayer self-rolled structures exhibit an enhanced electrochemical behavior over commercial Si microparticles. Remarkably, this behavior is further improved by introducing a double-sided carbon coating to form a C/Si/C self-rolled structure. With SnO2 as active material, an intriguing sandwich-stacked structure is studied. Furthermore, this novel structure, with a minimized strain energy due to strain release, exposes more active sites for the electrochemical reactions, and also provides additional channels for fast ion diffusion and electron transport. The electrochemical characterization and morphology evolution reveal the excellent cycling performance and stability of such structures.

Dans cette thèse nous démontrons le travail fait sur deux matériaux de cathodes pour les piles lithium-ion. Dans la première partie, nous avons préparé du phosphate de fer lithié (LiFePO4) par deux méthodes de lithiation présentées dans la littérature qui utilisent du phosphate de fer (FePO4) amorphe comme précurseur. Pour les deux méthodes, le produit obtenu à chaque étape de la synthèse a été analysé par la spectroscopie Mössbauer ainsi que par diffraction des rayons X (DRX) pour mieux comprendre le mécanisme de la réaction. Les résultats de ces analyses ont été publiés dans Journal of Power Sources. Le deuxième matériau de cathode qui a été étudié est le silicate de fer lithié (Li2FeSiO4). Une nouvelle méthode de synthèse a été développée pour obtenir le silicate de fer lithié en utilisant des produits chimiques peu couteux ainsi que de l’équipement de laboratoire de base. Le matériau a été obtenu par une synthèse à l’état solide. Les performances électrochimiques ont été obtenues après une étape de broyage et un dépôt d’une couche de carbone. Un essai a été fait pour synthétiser une version substituée du silicate de fer lithié dans le but d’augmenter les performances électrochimiques de ce matériau. / In this thesis, we demonstrate work on two different cathode materials for lithium-ion batteries. First, the synthesis of lithium iron phosphate (LiFePO4) is reproduced from literature using two lithiation methods starting with amorphous iron phosphate (FePO4). For both reactions, the product at each step of the synthesis was analyzed using Mössbauer Spectroscopy and X-ray diffraction in order to gain further insight of the reaction mechanism. The results of this work were published in Journal of Power Sources. The second cathode material of interest was lithium iron silicate (Li2FeSiO4). A novel synthetic method was developed to produce lithium iron silicate cost effectively starting with low cost precursors and basic laboratory equipment. The material was synthesized using a solid- state synthesis after milling and carbon coating, electrochemical performance was evaluated. An attempt was made to synthesize off-stoichiometric lithium iron silicate in order to increase the electrochemical performance of the material.

Dans cette thèse, nous démontrons des travaux sur la synthèse à faible coût des matériaux de cathode et l'anode pour les piles lithium-ion. Pour les cathodes, nous avons utilisé des précurseurs à faible coût pour préparer LiFePO4 et LiFe0.3Mn0.7PO4 en utilisant une méthode hydrothermale. Tout d'abord, des matériaux composites (LiFePO4/C) ont été synthétisés à partir d'un précurseur de Fe2O3 par une procédé hydrothermique pour faire LiFePO4(OH) dans une première étape suivie d'une calcination rapide pour le revêtement de carbone. Deuxièmement, LiFePO4 avec une bonne cristallinité et une grande pureté a été synthétisé en une seule étape, avec Fe2O3 par voie hydrothermale. Troisièmement, LiFe0.3Mn0.7PO4 a été préparé en utilisant Fe2O3 et MnO comme des précurseurs de bas coûts au sein d'une méthode hydrothermale synthétique. Pour les matériaux d'anode, nous avons nos efforts concentré sur un matériau d'anode à faible coût α-Fe2O3 avec deux types de synthèse hydrothermales, une a base de micro-ondes (MAH) l’autre plus conventionnelles (CH). La nouveauté de cette thèse est que pour la première fois le LiFePO4 a été préparé par une méthode hydrothermale en utilisant un précurseur Fe3+ (Fe2O3). Le Fe2O3 est un précurseur à faible coût et en combinant ses coûts avec les conditions de synthèse à basse température nous avons réalisé une réduction considérable des coûts de production pour le LiFePO4, menant ainsi à une meilleure commercialisation du LiFePO4 comme matériaux de cathode dans les piles lithium-ion. Par cette méthode de préparation, le LiFePO4/C procure une capacité de décharge et une stabilité de cycle accrue par rapport une synthétisation par la méthode à l'état solide pour les mêmes précurseurs Les résultats sont résumés dans deux articles qui ont été récemment soumis dans des revues scientifiques. / In this thesis, low cost syntheses of cathode and anode materials for lithium ion batteries will be presented. For cathode materials, low cost precursors were used to prepare LiFePO4 and LiFe0.3Mn0.7PO4 using low temperature hydrothermal method. Initially, a LiFePO4/C composite material was synthesized from a Fe2O3 precursor using a hydrothermal method to prepare LiFePO4(OH) in a first step followed by a fast calcination and carbon coating. Secondly, LiFePO4 with good crystallinity and high purity was synthesized, in one step, with nanometric sized Fe2O3 by a hydrothermal method. Thirdly, LiFe0.3Mn0.7PO4 was prepared using low cost Fe2O3 and MnO as precursors within a hydrothermal synthetic method. For anode materials, a low cost anode material α-Fe2O3 was prepared using two hydrothermal synthetic methods, microwave assisted (MAH) and conventional hydrothermal (CH). The novelty of the thesis is for the first time LiFePO4 has been prepared using a low cost Fe3+ precursor (Fe2O3) by a hydrothermal method. Low cost precursors and low temperature synthesis conditions will greatly reduce the synthetic cost of LiFePO4, leading to greater commercialization of LiFePO4 as a cathode materials for lithium-ion batteries. The as-prepared LiFePO4/C product provided enhanced discharge capacity and cycling stability compared to that synthesized using a solid state method with the same precursors. The results were summarized within two articles that were recently submitted to peer reviewed scientific journals.

No description available.

Le procédé sol-gel non-hydrolytique (SGNH) offre une alternative intéressante au procédés sol-gel classiques. Notamment, la « voie éther », impliquant la réaction de précurseurs chlorures ou oxychlorures avec avec un éther comme donneur d’oxygène, est une méthode simple et efficace pour la préparation d’oxydes et d’oxydes mixtes mésoporeux. Les batteries Li-ion sont omniprésentes aussi bien dans des applications portables que pour des véhicules électriques ou hybrides. Cependant, les performances des électrodes commerciales sont insuffisantes pour des applications haute puissance. TiO2 est un candidat prometteur pour remplacer les anodes de graphitie dans les batteries Li-ion, mais sa conductivité électronique doit être améliorée. L’objectif de ce travail de thèse est d’utiliser les avantages du procédé SGNH pour préparer des matériaux d’électrodes à base de TiO2. Deux approches ont été explorées, mettant en jeu la voie éther en l’absence de tout solvant ou additif. Premièrement, des oxydes mésoporeux à structure hiérarchique, TiO2 et TiO2-V2O5, ont été synthétisés par calcination des xérogels. Deuxièmement, des nanocomposites mésoporeux constitués de nanoparticules de TiO2 recouvertes d’un film de carbone ont été obtenus par pyrolyse sous atmosphère d’argon, l’éther jouant le rôle de donneur d’oxygène et aussi, pour la première fois, de source de carbone. Les matériaux ont été caractérisés par physisorption d’azote, microscopie électronique, DRX, spectroscopie Raman, ATG ainsi que par RMN 13C CPMAS pour les nanocomposites. Les performances en insertion-désinsertion du lithium ont été étudiées par cyclage galvanostatique à différentes densités de courant. / Non-hydrolytic sol-gel (NHSG) provides useful alternatives to conventional sol-gel routes. In particular, the ether route based on the reaction of chloride or oxychloride precursors with ether oxygen donors is a well-established method for the preparation of mesoporous oxides and mixed-oxides. Li-ion batteries are ubiquitous in the field of electrochemical energy storage, from mobile devices to electric and hybrid vehicles. However, commercial electrode materials do not fulfill all the requirements needed for high-power applications. TiO2 is as a promising material to replace graphite anodes in high-power Li-ion batteries, despite its poor electronic conductivity, which must be improved. In this context, the objective of this PhD thesis is the conception of different TiO2-based electrode materials benefitting from NHSG advantages. Two different approaches were developed, using the ether route in the absence of any solvent or additive. First, hierarchical mesoporous oxides, TiO2 and TiO2-V2O5, were synthesized by calcination of xerogels in air. Secondly, mesoporous nanocomposites built of carbon-coated TiO2 nanoparticles were obtained by pyrolysis under argon of the xerogels; in this case, the ether is used for the first time as both as an oxygen donor and a carbon source. The texture and the structure of the resulting materials were characterized by N2 physisorption, electron microscopy, XRD, and Raman spectroscopy. TiO2/C samples were further analyzed by TGA and 13C CPMAS-NMR. Galvanostatic cycling at different current rates was performed to determine the electrochemical performances in lithium insertion-deinsertion.

Rechargeable Li-ion batteries and supercapacitors are the most promising electrochemical energy storage devices in terms of energy density and power density, respectively. Recently, nanostructured materials have gained enormous interest in the field of energy technology as they have special properties compared to the bulk. Commercially available Li-ion batteries, which are the most advanced among the rechargeable batteries, utilize microcrystalline transition metal oxides as cathode materials which act as lithium insertion hosts. To explore better electrochemical performance the use of nanomaterials instead of conventional materials would be an excellent alternative. High Li-ion insertion at high discharge rates causes slow Li+ transport which in turn results in concentration polarization of lithium ions within the electrode material, causing a drop in cell voltage. This eventually, leads in termination of the discharge process before realizing the maximum capacity of the electrode material being used. This problem can be addressed by decreasing the average particle size which leads to an increase in surface area of the electrode material. Nanostructured materials, because of their high surface area and large surface to volume ratio, to some extent can overcome the problem of slow diffusion of ions. Supercapacitors are electrical energy storage devices which can deliver large energy in a short time. A supercapacitor can be used as an auxiliary energy device along with a primary source such as a battery or a fuel cell to achieve power enhancement in short pulse applications. Active materials for supercapacitors are classified into three categories: (i) carbonaceous materials, (ii) conducting polymers and (iii) metal oxides. Among the materials studied over the years, metal oxides have been considered as attractive electrode materials for supercapacitors due to the following merits: variable oxidation state, good chemical and electrochemical stability, ease of preparation and handling. The performance of supercapacitors can be enhanced by moving from bulk to nanostructured materials. The theme of the thesis is to explore novel routes to synthesize nanostructured materials for Li-ion batteries and supercapacitors, and to investigate their physical and electrochemical characteristics. Chapter I is an introduction of various types of electrochemical energy systems such as battery, fuel cell and supercapacitor. A brief review is made on electrode materials for Li-ion batteries and supercapacitors, and nanostructured materials. Chapter II deals with the study of nanostrip orthorhombic V2O5 synthesized by a two-step procedure, with the formation of a vanadyl ethylene glycolate precursor and post-calcination treatment. The precursor and the final product are characterized for phase and composition by powder X-ray diffraction (XRD), infrared (IR) spectroscopy, thermal analysis (TGA) and X-ray photoelectron spectroscopy (XPS). The morphological changes are investigated using field emission scanning electron microscopy (FE-SEM) and high resolution transmission electron microscopy (HRTEM). It is found that the individual strips have the following dimensions, length: 1.3 μm, width: 332 nm and thickness: 45 nm. The electrochemical lithium intercalation and de-intercalation of nanostrip V2O5 is investigated by cyclic voltammetry (CV), galvanostatic charge-discharge cycling, galvanostatic intermittent titration technique (GITT) and electrochemical impedance spectroscopy. Chapter III describes the synthesis of nanoparticels of LiMn2O4 by microwave assisted hydrothermal method. The phase and purity of spinel LiMn2O4 are confirmed by powder XRD analysis. The morphological studies are carried out using FE-SEM and HRTEM. The electrochemical performance of spinel LiMn2O4 is studied by using CV and galvanostatic charge-discharge cycling. The initial discharge capacity is found to be about 89 mAh g-1 at a current density of 21 mA g-1 with reasonably good cyclability. Chapter IV deals with synthesis of MoO2 nanoparticles through ethylene glycol medium and its electrochemical characterization. XRD data confirms the formation MoO2 on monoclinic phase, space group P21/c. Polygon shape of MoO2 is observed in HRTEM. MoO2 facilitates reversible insertion-extraction of Li+ ions between 0.25 to 3.0 V vs. Li/Li+. CV and galvanostatic charge-discharge cycling are conducted on this anode material to complement the electrochemical data. Chapter V reports the synthesis of nanostructured MnO2 at ambient conditions by reduction of potassium permanganate with aniline. Physical characterization is carried out to identify the phase and morphology. The as prepared MnO2 is amorphous and it contains particles of 5 to 10 nm in diameter. On annealing at a temperature > 400 °C, the amorphous MnO2 attains crystalline α-phase with a concomitant change in morphology. A gradual conversion of nanoparticles to nanorods (length 500-750 nm and diameter 50-100 nm) is evident from SEM and TEM studies. High resolution TEM images suggest that nanoparticles and nanorods grow in different crystallographic planes. The electrochemical lithium intercalation and de-intercalation of nanorods was performed by (CV) and galvanostatic charge-discharge cycling. The initial discharge capacity of nanorod α-MnO2 is found to be about 197 mAh g-1 at a current density of 13.0 mA g-1. Capacitance behavior of amorphous MnO2 is studied by CV and galvanostatic charge-discharge cycling in a potential range from -0.2 to 1.0 V vs. SCE in 0.1 M sodium sulphate solution. The effect of annealing on specific capacitance is also investigated. Specific capacitance of about 250 F g-1 is obtained for as prepared MnO2 at a current density of 0.5 mA cm-2 (0.8 A g-1). Chapter VI pertains to electrochemical supercapacitor studies on nanostructured MnO2 synthesized by polyol method. Although X-ray diffraction (XRD) pattern of the as synthesized nano-MnO2 shows poor crystallinity, it is found that it is locally arranged in δ-MnO2 type layered structure composed of edge-shared network of MnO6 octahedra by Mn K-edge X-ray Absorption Near Edge Structure (XANES) measurement. Annealed MnO2 shows high crystalline tunneled based α-MnO2 as confirmed by powder XRD pattern and XANES. As synthesized MnO2 exhibits good cyclability as an electrode material for supercapacitor. In Chapter VII, capacitance behavior of nanostrip V2O5, TiO2 coated V2O5 and nanocomposites of PEDOT/V2O5 are presented. Structural and morphological studies are carried out by powder XRD, IR, TGA, SEM and TEM. Cyclic voltammogram of pristine V2O5 shows the regular rectangular shape indicating the ideal capacitance behavior in aqueous 0.1 M K2SO4. The SC value of pristine V2O5 is found to be about 100 F g-1. Nanostrip V2O5 is modified with TiO2 using titanium isobutoxide to enhance the capacitance retention upon cycling. Only 48 % of the initial capacitance remains in the case of pristine V2O5 after 100 cycles, while TiO2 coated V2O5 exhibits better cyclability with capacitance of 70 % of the initial capacitance. The capacitance retention is attributed to the presence of TiO2 on the surface of V2O5 which prevents the vanadium dissolution into the electrolyte. Microwave assisted hydrothermally synthesized PEDOT/V2O5 nanocomposites are utilized as capacitor materials. The initial SC of PEDOT/V2O5 (237 F g-1) is higher than that of either pristine V2O5 or PEDOT. The enhanced electrochemical performance is attributed to synergic effect and an enhanced bi-dimensionality. Details of the above studies are described in the thesis with a conclusion at the end of each Chapter.

The demands for advanced power sources with high energy efficiency, minimum environmental impact, and low cost have been the impetus for the development of a new generation of batteries and fuel cells. One of the key challenges in this effort is to develop and fabricate effective electrodes with desirable composition, microstructure and performance. This work focused on the design, fabrication, and characterization of nanostructured electrodes in an effort to minimize electrode polarization losses. Solid-state diffusion often limits the utilization and rate capability of electrode materials in a lithium-ion battery, especially at high charge/discharge rates. When the fluxes of Li+ insertion or extraction exceed the diffusion-limited rate of Li+ transport within the bulk phase of an electrode, concentration polarization occurs. Further, large volume changes associated with Li+ insertion or extraction could induce stresses in bulk electrodes, potentially leading to mechanical failure. Interconnected porous materials with high surface-to-volume ratio were designed to suppress the stress and promote mass transport. In this work, electrodes with these unique architectures for lithium ion batteries have been fabricated to improve the cycleability, rate capability and capacity retention. Cathodic interfacial polarization represents the predominant voltage loss in a low-temperature SOFC. For the first time, regular, homogeneous and bimodal porous MIEC electrodes were successfully fabricated using breath figure templating, which is self-assembly of the water droplets in polymer solution. The homogeneous macropores promoted rapid mass transport by decreasing the tortuosity. And mesoporous microstructure provided more surface areas for gas adsorption and more TPBs for the electrochemical reactions. Moreover, composite electrodes were developed with a modified sol-gel process for honeycomb SOFCs. The sol gel derived cathodes with fine grain size and large specific surface area, showed much lower interfacial polarization resistances than those prepared by other existing processing methods. Nanopetals of cerium hydroxycarbonate have been synthesized via a controlled hydrothermal process in a mixed water-ethanol medium. The formation of the cerium compound depends strongly on the composition of the precursors, and is attributed to the favored ethanol oxidation by Ce(IV) ions over Ce(IV) hydrolysis process. Raman studies showed that microflower CeO2 preferentially stabilizes O2 as a peroxide species on its surface for CO oxidation.