This thesis work deals with the volume changes during the solidification of cast irons and peritectic steels. The volume changes in casting metals are related to the expansion and/or contraction of the molten metal during solidification. Often, different types of shrinkage, namely macro- and micro-shrinkage, affect the casting quality. In addition to that, exposure of the metal casting to higher contraction or expansion during the solidification might also be related to internal strain development in samples, which eventually leads to surface crack propagation in some types of steel alloys during continuous casting. In consequence, a deep understanding of the mechanisms and control of the solidification will improve casting quality and production. All of the experiments during the entire work were carried out on laboratory scale samples. Displacement changes during solidification were measured with the help of a Linear Variable Displacement Transformer (LVDT). All of the LVDT experiments were performed on samples inside a sand mould. Simultaneously, the cooling curves of the respective samples during solidification were recorded with a thermocouple. By combining the displacement and cooling curves, the volume changes was evaluated and later used to explain the influence of inoculants, carbon and cooling rates on volume shrinkages of the casting. Hypoeutectic grey cast iron (GCI) and nodular cast iron (NCI) with hypo-, hyper- and eutectic carbon compositions were considered in the experiments from cast iron group. High nickel alloy steel (Sandvik Sanbar 64) was also used from peritectic steel type. These materials were melted inside an induction furnace and treated with different types of inoculants before and during pouring in order to modify the composition. Samples that were taken from the LVDT experiments were investigated using a number of different  methods in order to support the observations from the displacement measurements:  Differential Thermal Analysis (DTA), to evaluate the different phase present; Dilatometry, to see the effect of cooling rates on contraction for the various types of alloys; metallographic studies with optical microscopy; Backscattered electrons (BSE) analysis on SEM S-3700N, to investigate the different types of oxide and sulphide nuclei; and bulk density measurements  by applying Archimedes' principle. Furthermore, the experimental volume expansion during solidification was compared with the theoretically calculated values for GCI and NCI. It was found that the casting shows hardly any shrinkage during early solidification in GCI, but in the eutectic region the casting expands until the end of solidification. The measured and the calculated volume changes are close to one another, but the former shows more expansion. The addition of MBZCAS (Si, Ca, Zr, Ba, Mn and Al) promotes more flake graphite, and ASSC (Si, Ca, Sr and Al) does not increase the number of eutectic cells by much. In addition to that, it lowers the primary austenite fraction, promotes more eutectic growth and decreases undercooled graphite and secondary dendritic arm spacing (SDAS). As a result, the volume expansion changes in the eutectic region. The expansion during the eutectic growth increase with an increase in the inoculant weight percentage. At the same time, the eutectic cells become smaller and increase in number. The effect of the inoculant and the superheat temperature shows a variation in the degree of expansion/contraction and the cooling rates for the experiments. Effective inoculation tends to homogenize the eutectic structure, reducing the undercooled and interdendritic graphite throughout the structure. In NCI experiments, it was found that the samples showed no expansion in the transversal direction due to higher micro-shrinkages in the centre, whereas in the longitudinal direction the samples shows expansion until solidification was complete.   The theoretical and measured volume changes agreed with each other. The austenite fraction and number of micro-shrinkage pores decreased with increase in carbon content. The nodule count and distribution changes with carbon content. The thermal contraction of NCI is not influenced by the variation in carbon content at lower cooling rates. The structural analysis and solidification simulation results for NCI show that the nodule size and count distribution along the cross-sections at various locations are different due to the variation in cooling rates and carbon concentration. Finer nodule graphite appears in the thinner sections and close to the mold walls. A coarser structure is distributed mostly in the last solidified location. The simulation result indicates that finer nodules are associated with higher cooling rate and a lower degree of microsegregation, whereas the coarser nodules are related to lower cooling rate and a higher degree of microsegregation. As a result, this structural variation influences the micro-shrinkage in different parts. The displacement change measurements show that the peritectic steel expands and/or contracts during the solidification. The primary austenite precipitation during the solidification in the metastable region is accompanied by gradual expansion on the casting sides. Primary δ-ferrite precipitation under stable phase diagram is complemented by a severe contraction during solidification. The microstructural analysis reveals that the only difference between the samples is grain refinement with Ti addition. Moreover, the severe contraction in solidification region might be the source for the crack formation due to strain development, and further theoretical analysis is required in the future to verify this observation. / <p>QC 20170228</p>

Ces dernières années un nouveau type de décharges hors équilibre thermodynamique, aptes à générer des micro jets de plasma se propageant en atmosphère libre, a suscité beaucoup d’intérêt dans la communauté scientifique. Ces micro jets, produits dans des structures type décharge à barrière diélectrique, ont des propriétés particulièrement intéressantes, tant sur le plan de la physique des plasmas que sur celui des applications, en particulier pour des applications biomédicales ou de traitement de surface.Dans ce travail de thèse il est démontré que ces jets de plasma correspondent à la propagation à grande vitesse d'un front d'ionisation sans déplacement de matière. Une caractérisation des propriétés des jets (vitesse et distance de propagation) a été effectuée en fonction de la tension appliquée, du débit, de la composition du gaz, et de la géométrie de la décharge. La distribution spatio-temporelle des espèces réactives produites par le jet a été mesurée, et en particulier celle de l'état métastable He (2³S) mesuré par absorption laser. Des densités comprises entre 1.10¹² et 5.10¹³ cm-³ ont été obtenues pour l’état He (2³S). Sa distribution est annulaire à la sortie de la structure de la décharge et se referme le long du jet. La densité maximale est obtenue à une distance correspondant à la moitié de la zone où les atomes métastables sont présents, ce qui est en contradiction avec les modèles actuels. De plus, afin de mieux comprendre la physique des jets de plasma, nous avons fait interagir deux jets placés l’un en face de l’autre. L'étude de la contre propagation de deux jets révèle qu’il existe une distance minimale d'approche laissant entre eux une zone exempte de plasma. Après l’extinction des deux plasmas, une seconde décharge s’amorce exactement dans cette zone. Une étude détaillée couplant diagnostics électrique, imagerie ultra-rapide et spectroscopie d'émission nous a permis de montrer que cette décharge secondaire est due à une inversion de polarité conduisant à la création transitoire d'un piège à électrons.Dans le but d'aborder l'étude des applications des jets de plasma au domaine biologique, nous avons également étudié la dégradation de l’ADN plasmidique par un jet de plasma. Nous avons mis en évidence que ce type de plasma induit majoritairement des cassures simples et doubles brins, alors que très peu d’oxydations de base ou de sites abasiques sont observés, ceci même avec l’ajout de quelques pourcents d’oxygène dans le gaz. / Micro plasma jets operating at atmospheric pressure in free atmosphere have recently attracted great attention because of their numerous advantages. In fact, micro plasma jets can be operated stably at atmospheric pressure and propagated over some centimeters in a free atmosphere. Moreover, these jets are non-thermal plasmas and create numerous reactive species. These properties allow to use this kind of plasma in many applications, such as surface treatment, decontamination, and plasma medicine.In this work it is shown that these micro plasma jets correspond to the fast propagation of an ionization front with no displacement of matter. A characterization of the plasma proprieties (e.g. distance and velocity of propagation) has been done as a function of the applied voltage, gas flow, gas composition and discharge geometry. The spatiotemporal distribution of the reactive species created by the plasma has been measured, with a special focus on the helium metastable atoms which have been measured by absorption laser spectroscopy. The helium metastable atom densities obtained are in the range of 1.10¹² to 5.10¹³ cm-³. Thanks to a very good spatiotemporal resolution, we have done a time-resolved full cartography of the plasma. This allowed us to show that the helium metastable atom distribution is annular near the nozzle and becomes circular as the plasma propagates. The maximum helium metastable atoms density has been measured at about half of the distance where the helium metastable atoms are present. This observation is in contradiction with results reported by numerical models. To gain further insight into the physical processes of the plasma, we have placed two micro plasma jets face to face. This study showed that both plasmas interact in such a way that they never come into contact, letting a space free of plasma between them. Moreover, we revealed that after the extinction of the plasmas, a second discharge is ignited in the previously free space. Fast imaging, spectroscopy diagnostics and electrical measurements showed that this second discharge is due to a polarity reversal, which creates an electron trap. Aiming the study of the application of micro plasma jets in the plasma medicine field, we have studied the degradation of plasmid DNA by our plasma jet. We observed that the plasma treatment leads mostly to single and double strands breaks, and to very little base oxidation and abasite site, even when oxygen is added into the gas mixture.

Cette thèse décrit l'observation expérimentale de l'effet Hong-Ou-Mandel avec une sourceatomique ultra-froide. L’expérience originale réalisée en 1987 par C. K. Hong, Z. Y. Ou et L. Mandel illustre de façon simple une interférence à deux particules explicable uniquement par la mécanique quantique : deux particules bosoniques et indiscernables, arrivant chacune sur une face d'entrée différente d'une lame semi-réfléchissante ressortent ensemble. Cet effet se traduit par une réduction du taux de détection en coïncidence entre les deux voies de sortie quand les particules arrivent simultanément sur la lame. Cette expérience fut originalement réalisée avec des photons et nous rapportons ici la première mise en oeuvre expérimentale avec des particules massives se propageant dans l’espace libre.Après présentation des différentes techniques nécessaires à sa réalisation, nous décrivons cette expérience et analysons les résultats obtenus. En particulier, la réduction du taux de coïncidence est suffisamment forte pour exclure toute interprétation classique ; l'observation de cet effet constitue une brique fondamentale dans le domaine de l’information quantique atomique. / In this thesis, we report the first realisation of the Hong–Ou–Mandel experiment with massive particles in momentum space. This milestone experiment was originally performed in quantum optics: two photons arriving simultaneously at the input ports of a 50:50 beam-splitter always emerge together in one of the output ports. The effect leads to a reduction of coincidence counts which translates into a dip when particles are indistinguishable. We performed the experiment with metastable helium atoms where the specificities of the Micro-Channel-Plate detector allows one to recover the momentum vector of each individual atom.After listing the necessary tools to perform this experiment with atoms, the experimental sequence is discussed and the results are presented. In particular we measured a coincidence count reduction that cannot be explained through any simple classical model. This corresponds to the signature of a two-particle interference, and confirms that our atomic pair source produces beams which have highly correlated populations and are well mode matched. This opens the prospect of testing Bell’s inequalities involving mechanical observables of massive particles, such as momentum, using methods inspired by quantum optics. It also demonstrates a new way to produce and benchmark twin-atom pairs that may be of interest for quantum information processing.

On considère l'évolution adiabatique des états vitreux sous perturbations extérieures. Bien que le formalisme que nous utilisons soit très général, nous nous concentrons ici sur les sphères dures en dimension infinie où une analyse exacte est possible. Nous considérons perturbations de la frontière, notamment compression ou cisaillement simple et nous calculons la réponse des états vitreux à ces perturbations : pression et contrainte de cisaillement. Nous constatons un dépassement des deux quantités avant que l'état vitreux ne devienne instable à un point spinodal, où il fond dans le liquide (ou cède). Nous estimons également la limite d'élasticité du verre. Enfin, nous étudions la stabilité des bassins vitreux vers la rupture en sous-bassins, correspondant à une transition de Gardner. Nous constatons que près de la transition dynamique, les verres subissent une transition de Gardner après une perturbation infinitésimale. Nous étudions ensuite le régime de haute pression et haut cisaillement au-delà de la transition de Gardner. / We consider the adiabatic evolution of glassy states under external perturbations. Although the formalism we use is very general, we focus here on infinite-dimensional hard spheres where an exact analysis is possible. We consider perturbations of the boundary, i. e. compression or (volume preserving) shear-strain, and we compute the response of glassy states to such perturbations: pressure and shear-stress. We find that both quantities over shoot before the glass state becomes unstable at a spinodal point where it melts into a liquid (or yields). We also estimate the yield stress of the glass. Finally, we study the stability of the glass basins towards breaking into sub-basins, corresponding to a Gardner transition. We find that close to the dynamical transition, glasses undergo a Gardner transition after an infinitesimal perturbation. We then study the high-pressure and high-strain regime beyond the Gardner transition.

Les alliages de titane β-métastables comme le Ti-10V-2Fe-3Al se substituent progressivement aux alliages α/β dans les applications aéronautiques du fait de leur résistance spécifique améliorée. Leurs microstructures d'emploi sont cependant complexes et multi-échelles, constituées d'une matrice β (de grains millimétriques) partiellement transformée en nodules primaires αp (micrométriques) et en lamelles secondaires αs (sub-micrométriques). Les propriétés finales peuvent être très sensibles aux variations locales de microstructures et sont souvent non maîtrisées lors du forgeage de pièces massives. De plus la matrice β qui représente ~40% du volume et qui a un comportement élastique et plastique fortement anisotrope, comme la phase α, complique la compréhension des mécanismes de déformation en jeu. Le premier objectif de cette thèse est de mettre en œuvre des techniques de caractérisation multi-échelles (la diffraction des neutrons, l'imagerie électronique couplée à l'analyse d'image et l'EBSD, la reconstruction des microtextures de haute température β/αp) pour analyser efficacement la microstructure/texture des constituants β/αp/αs et caractériser leurs hétérogénéités au sein de demi-produits et de pièces obtenues par matriçage. Les résultats permettent d'analyser la fragmentation des grains β en sous-grains, les macrozones αp, le maintien de relation d'orientation entre β/αp et l'organisation des lamelles αs en colonies ou paniers tressés, en pointant les différences de taille de domaines révélés par la cristallographie et l'imagerie standard. Le second objectif est d'appliquer cette méthodologie à l'analyse de facies de rupture d'éprouvettes présentant un comportement singulier (en traction ou en fatigue) pour caractériser les configurations microstructurales à l'origine de l'amorçage de fissures. Cette analyse a principalement été réalisée par polissage manuel du faciès couplé à des acquisitions EBSD mais également en exploitant le potentiel de l'imagerie 3D par MEB-FIB (Focus Ion Beam) et la technique TKD (Transmission Kikuchi Diffraction) sur lame mince prélevée au niveau d'un site d'amorçage par FIB. Enfin, cette étude expérimentale a été complétée par une première approche en simulation micromécanique sur une microstructure modèle 100% β. L'objectif était d'évaluer l'influence de l’anisotropie élastique de la phase β sur la genèse de contraintes d'incompatibilités dans les régimes élastique et élasto-plastique. L'ensemble des résultats contribue à une meilleure compréhension des variations de propriétés mécaniques en lien avec la microstructure locale / The β-metastable titanium alloys such as Ti-10V-2Fe-3Al are gradually replacing α/β alloys in aeronautical applications thanks to their improved specific strength. However, their microstructures are complex and multi-scale, consisting of a β matrix (of millimetric grains) partially transformed into primary αp nodules (micrometric) and secondary αs lamellae (sub-micrometric). The final mechanical properties are very sensitive to local variations of the microstructure, which are not always fully controlled during forging of massive parts. Moreover, the β matrix, which represent 40% of the volume and whose elastic and plastic behavior is strongly anisotropic (like the α phase) complicates the understanding of the mechanisms of deformation. The first objective of this thesis was to efficiently characterize the microstructure/texture of the different constituents (β/αp/αs) and their heterogeneities within half-finished products and forged parts by using techniques of multi-scale characterization (neutron diffraction, electronic imaging coupled with image analysis and EBSD, reconstruction of high temperature microtextures β/αp). As a result the fragmentation of the β grains into subgrains, the αp macrozones, the destruction of the orientation relation between β/αp and the organization of the αs lamellae in colonies or basket weave was quantified and the differences in size of domains revealed by crystallography and by standard imaging were pointed out. The second objective is to apply this methodology to the analysis of fracture surfaces of samples exhibiting singular behavior (in tension or in fatigue) in order to characterize the microstructural configurations leading to early cracking. This analysis was mainly performed by manual polishing coupled with EBSD acquisitions but also by using 3D imaging by SEM-FIB (Focus Ion Beam) and TKD (Transmission Kikuchi Diffraction) technique on a thin foil FIB-extracted from the crack initiation site. Finally, this experimental study was completed by a micromechanical simulation on a 100% β model microstructure. The objective was to evaluate the influence of the elastic anisotropy of the β phase on the genesis of incompatibility stresses in the elastic and elasto-plastic regimes. The overall results contribute to a better understanding of the variations of mechanical properties related to the local microstructure

No description available.

Maßgeschneiderte Eigenschaften von Funktionsmaterialien sind ein fundamentaler Aspekt für die Technologien unserer Gesellschaft und deren Weiterentwicklung. In diesem Zusammenhang bilden die Modifizierung bestehender Synthesestrategien und die Entwicklung neuartiger Synthesewege die grundlegende Voraussetzung für Innovation. Der Zugang zu den benötigten Materialien wird in den bis dato angewandten Synthesemethoden häufig durch die thermodynamische Stabilität einer Verbindung begrenzt. Zielstellung der vorliegenden Arbeit ist es, eine Strategie zur postsynthetischen Umwandlung und Modifizierung bereits vorhandener komplex strukturierter Feststoffe anzuwenden, durch die es gelingt, Zugang zu weiteren Materialien zu erhalten. Als Feststoffprekursoren wurden hierfür verschiedene ternäre und quaternäre, bismutreiche Subhalogenide gewählt, die bei niedrigen Temperaturen bis 70 °C mit dem Reduktionsmittel n-Butyllithium (nBuLi) zur Reaktion gebracht wurden, um diese in topochemischen Reaktionen zu neuen intermetallischen Phasen umzuwandeln. Die Bismutsubiodide Bi12Ni4I3, Bi8Ni8SI2 und Bi28Ni25I5 enthalten intermetallische Stäbe, deren Querschnitte nur vier bis elf Atome umfassen, was effektiven Durchmessern von ca. 0,8 bis 1,2 nm entspricht. Zudem befinden sich Iodidionen in den Kristallstrukturen, die die metallischen Stäbe voneinander separieren. Die reduktiven Behandlungen dieser Feststoffprekursoren führten jeweils zur quantitativen Deinterkalation der Iodidionen und dadurch zur Zusammenlagerung der metallischen Stäbe zu kompakten Stabpackungen. In Pseudomorphosen wurden zum einen Kristalle erhalten, die eine Vielzahl parallel angeordneter Bi3Ni-Faserbündel enthielten, zum anderen bildeten sich die bisher unbekannten, kristallinen Phasen Bi8Ni8S und Bi28Ni25. Während bei den Umwandlungen die strukturellen Charakteristiken der intermetallischen Teilstrukturen der Bismutsubiodide auf die reduzierten Phasen übertragen werden, ändern sich die elektronischen Situationen mit der Variation der Elektronenzahl. Dies lässt sich besonders gut am Beispiel der Umwandlung des Bismutsubiodids Bi28Ni25I5 in die reduzierte Phase Bi28Ni25 verdeutlichen. Die elektronische Struktur ändert sich durch die Reduktion kaum, sodass die zusätzlichen Elektronen im intermetallischen Teil antibindende Zustände füllen. Das intermetallische Bindungssystem verhält sich dabei wie ein strukturell rigides Elektronenreservoir und toleriert die Änderung der Elektronenzahl bei der topochemischen Umwandlung zu Bi28Ni25. Mit der elektronisch ungünstigen Situation geht die Metastabilität der reduzierten intermetallischen Phase einher. Die reduktive Behandlung des Bismutsubiodids Bi13Pt3I7 führte nicht nur zur selektiven topochemischen Deinterkalation von Iodidionen sondern zusätzlich zum Ausbau von Bismutatomen, wodurch die in Bi13Pt3I7 vorhandenen Iodidobismutatschichten in Iodidschichten umgewandelt werden. Die intermetallischen Schichten der Ausgangsverbindung bleiben erhalten und nähern sich an, sodass das bis dato unbekannte Bismutsubiodid Bi12Pt3I5 resultiert. Das topotaktische Fortbestehen der intermetallischen Schichten zeigt sich dabei an intermediär gebildeten Kompositkristallen aus Mutter- und Tochterverbindung. Durch den Abbau der isolierenden Iodidobismutat¬schichten erfolgen die elektronische Kopplung der intermetallischen Schichten und der Übergang des zwei-dimensionalen Metalls Bi13Pt3I7 in das dreidimensionale Metall Bi12Pt3I5. Die topochemische Reaktion wird durch eine Reaktionstemperatur von 45 °C limitiert: Bei erhöhter Reaktionstemperatur bis 70 °C tritt eine Umstrukturierung unter weiterem Iod- und Bismutausbau auf, und die metastabile, binäre Phase Bi2Pt(hP9) wird aufgebaut. Die dichte Kristallstruktur des erstmals dargestellten Bismutsubchlorids Bi12Rh3Cl2 baut sich aus einem intermetallischen [Bi4Rh]-Netzwerk auf, in dessen Kanäle Chloridionen eingeschlossen sind. Im Zuge der Niedertemperaturreaktion mit nBuLi erfolgt ein unerwarteter quantitativer Austausch der Chloridionen gegen Bismutatome, der die Kristalle des Subchlorids in Kristalle der binären Verbindung Bi14Rh3 überführt. Die kristallchemische Analyse zeigte, dass den [RhBi8/2]-Antiprismen des [Bi4Rh]-Netzwerks die Funktion von Scharnieren zukommt, welche eine Aufweitung des intermetallischen Netzwerks ermöglichen. So entstehen breite Diffusionspfade, und es resultiert ein dreidimensionales Transportsystem für den enormen Massetransport durch den Kristall. Bei der Austauschreaktion werden die zuvor unabhängig voneinander leitenden intermetallischen Stränge kantenverknüpfter [RhBi8/2]-Würfel elektrisch kontaktiert. Die physikalischen Eigenschaften ändern sich dabei maßgeblich: Aus dem eingeschränkten Metall Bi12Rh3Cl2 entsteht der metastabile Supraleiter Bi14Rh3. Mit zunehmender Kenntnis über die Strategien zur postsynthetischen Umwandlung und Modifizierung komplexer Strukturen können diese grundsätzlich dazu beitragen, Materialien mit technologisch relevanten Eigenschaften darzustellen. Insbesondere Phasen, die nur bei hohen Temperaturen thermodynamische Stabilität erlangen oder sogar unter allen Bedingungen metastabil vorliegen, werden durch die geschickte Wahl der Synthesestrategie zugänglich. Möglicherweise werden mit dem wachsenden Wissen zu neuartigen Synthesestrategien die chemischen und physikalischen Eigenschaften eines Materials auf diesem Weg gezielt veränderbar. Insbesondere die herausragenden Stabilitäten der nanoskaligen, intermetallischen Stäbe werfen zudem die Frage auf, ob diese durch die Reaktion mit oberflächenaktiven Reagenzien vereinzelt werden können, um neuartige nanoskalige Leiter herzustellen.

Epitaxial growth is an important technique for the fabrication of film structures with good crystalline quality, e.g., monoatomic overlayers, multilayers, compound materials, and ordered alloys. Such epitaxially grown films are technologically important materials with, e.g., adjustable electronic, magnetic, and optical properties. In case of coherent or pseudomorphic epitaxy, the overlayer adapts the in-plane lattice parameters of the substrate, i.e., the overlayer is strained to match the lattice parameters parallel to the substrate surface (in-plane directions). Simultaneously, a relaxation of the film dimension perpendicular to the substrate-film interface occurs (out-of-plane direction). Thus, coherent epitaxy provides a method to put phases under strain, and it can stabilise a metastable state of the film material, if the substrate lattice matches this metastable structure. Bulk-like properties in thick overlayers, which adopt the body-centred tetragonal (BCT) crystal structure and which grow coherently on a suitable substrate with quadratic surface symmetry, are modelled by the epitaxial Bain path (EBP) in this thesis. The knowledge of the EBP allows to study properties of the overlayer as function of the substrate lattice parameter. In particular, strain effects on the film material, magnetic order in the overlayer, and the existence of possible metastable states are investigated by means of density functional theory (DFT) in the local spin density approximation (LSDA), and in the singular case of uranium, employing the generalised gradient approximation (GGA). Note that a symmetry property of the BCT structure states, that it is identical to the body-centred cubic (BCC) structure or the face-centred cubic (FCC) structure for definite ratios of the tetragonal lattice parameters. Our definition of the EBP has two, previously not considered consequences for EBPs in general: an EBP can be discontinuous, and the high symmetry cubic structures (FCC and BCC) need not be points on the EBP. Both cases occurred for several elements considered in this thesis. If, however, a cubic structure is a point on the EBP, then a symmetry property guarantees that the total energy along the EBP, E(a), is stationary at this cubic structure. We computed the EBPs of all transition metals (TMs), the post TMs Zn, Cd, and Hg, the alkaline earth metals Ca, Sr, and Ba, the lanthanides La and Lu, and the actinide U (35 elements were treated in total). For each element but Zr, Hg, and U, there are exactly two structures whose energies are minima on the EBP, and which exhibit neither in-plane nor out-of-plane stresses; for Zr, Hg, and U there are three minima each. All other states on the EBP exhibit in-plane stresses because they are a strained form of the stress-free structures. The possibility of metastability of these particular, stress-free structures, i.e., stabilisation of these structures without bonding to the substrate, was investigated by stability conditions based on linear elasticity theory (except for U). We predict that ten FCC structures and three BCT structures not known from the respective phase diagrams may be metastable. We studied the properties of ferromagnetic (FM) states on the EBP for the elements Fe, Co, and Ni, and moreover predict, that Mn, Ru, Os, and U order ferromagnetically for certain states of the EBP. The latter three elements are paramagnetic in their ground states. The onset of ferromagnetism in Os and U is not accompanied by a simultaneously fulfilled Stoner criterion. According to our results, antiferromagnetic order (with moment sequences up-down or up-up-down-down on successive (001) planes) is never more stable than FM order on any EBP for any element investigated. On the basis of our comprehensive results for all TMs, we analysed trends across each of the three TM series and similarities among the three series. We demonstrate, that the type of the EBP (a classification of extrema of E(a) by symmetry into types) follows a characteristic trend across each of the three TM series. We discuss exceptions (Mn, Fe, and Zr) to this trend. Another trend, identical for the three series, is found for the BCT­-FCC structural energy difference as function of the d-band filling (evaluated for BCT structures that define extrema of E(a)), which follows a similar trend as the well studied BCC­-FCC structural energy difference. Clear similarities among the three periods of elements are also reflected in the bulk moduli and in the elastic constants of the cubic or tetragonal structures, that define the global and local minima of E(a). The mentioned similarities suggest, that many properties which are associated with the EBPs of TMs, can be attributed to the occupation of the d-band, which is the most dominant feature of the electronic structure of TMs.

Les alliages de titane β métastables sont des matériaux de structure essentiels pour les applications aéronautiques de part leurs très bonnes propriétés mécaniques. En effet, ils présentent une résistance spécifique élevée, une bonne ductilité et forgeabilité et une excellente réponse aux traitements thermiques. Toutefois, il existe encore aujourd'hui à leur sujet des controverses et des questions ouvertes et ce, malgré les efforts pour comprendre les mécanismes d'évolution microstructurale au cours de traitements thermo-mécaniques et pour déterminer les phases en présence et leur contribution aux les propriétés mécaniques résultantes. Ce travail de thèse a pour objectif de déterminer la nature de la phase β et de caractériser la transformation β→α à haute et basse températures par des caractérisations fines en microscopie électronique à balayage et à transmission couplées à des mesures d'orientations cristallographiques et de composition chimique. L'alliage étudié est un Ti-5553 avec une microstructure initiale 100% β obtenue par mise en solution et trempe. Il a été démontré expérimentalement que la structure de la phase β métastable n'est pas purement cubique centrée. Les points de la phase β dans les clichés de diffraction présentent un allongement (streaking) et des points supplémentaires sont visibles aux positions de diffraction 1/2, 1/3 et 2/3. Par ailleurs, les images MET ont un aspect en moiré. A partir de ces résultats et de calculs crystallographiques, il a été prouvé que des déplacements atomiques sur les plans {110}β et {112}β forment une structure intermédiaire entre celle de la phase β parente et celles des phases α et ω, prouvant que la phase β a intrinsèquement initié une transformation. L'étude de la précipitation au cours du procédé thermomécanique dans le domaine α+β a révélé que des précipités α discontinus, équiaxes ou légèrement allongés (1~2μm) se forment aux joints β de forte et de faible désorientation mais rarement au coeur des grains β produisant ainsi une microstructure en "collier". La relation d'orientation de Burgers (ROB) entre les phases α et β est progressivement détruite par la déformation. L'écart à la ROB est plus marqué pour les précipités α qui se forment au joint de grains qu'à l'intérieur des grains. L'écart à la ROB augmente aussi avec la déformation, mais diminue avec la vitesse de déformation. Au cours des déformations en bas du domaine α+β, les précipités α ont une morphologie qui dépend de leur position. Au coeur des bandes de glissement, les grains α/β sont équiaxes et ne respectent pas la ROB. Entre les bandes de glissement, la microstructure est lamellaire où les phases α/β alternent et respectent la ROB. Dans ce dernier cas, une forte sélection de variantes a été observée: Seuls les deux ou trois variants favorisant l'accommodation de la déformation se sont formés. A titre de comparaison, dans l'état non déformé, les 12 précipités sont présents. La transformation β→α est retardée en cours de compression à haute température. Ceci est attribué à une compétition entre adoucissement et transformation de phase. Au contraire, celle-ci est favorisée au cours de la compression à plus basse température du fait que les défauts cristallins induits par la déformation jouent le role de sites de germination et que la croissance des précipités soit accéléré alors que l'adoucissement soit ralenti. Dans le Ti-5553, le mécanisme de déformation dominant est le glissement des dislocations. Dans les déformations en bas du domaine α+β, du glissement simple ou multiple avec deux ou trois systèmes de glissement activés. L'identification de ces systèmes a pu être effectuée par des analyses de traces. Cette thèse a résolu la nature de la phase β métastable et constitue un travail de référence pour l'étude de la transformation β→α au cours de traitement thermomécanique / Metastable β titanium alloys are important structural materials for aeronautical applications due to their high strength to density ratio, good ductility and workability and excellent hardenability. Despite the efforts in resolving the complex microstructural evolution related to thermomechanical processes and in gaining knowledge on the produced phases and their contribution to the resultant mechanical properties, there are still some controversial and unresolved issues. The aim of the present PhD work is to determine precisely the metastable nature of β phase and to characterize finely the characteristics of the β→α transformation during high and low temperature thermomechanical treatments. Investigations were performed on a Ti-5553 alloy with the single β phase initial microstructure obtained by solution treatment followed by quenching using scanning and transmission electron microscopy (SEM/TEM) coupled to crystallographic orientation measurements and chemical analyses. It was demonstrated experimentally that the structure of the β phase in the metastable titanium alloy is not “pure” body centered cubic. Diffraction diagrams presents streaking of the β diffraction spots and additional spots at the 1/2, the 1/3 and 2/3 diffraction positions. Also, striations are observed in TEM images. From this experimental evidence and crystallographic calculations, it was proved that atomic displacements on the {110}β and {112}β planes formed a structure between that of the parent β phase and that of the α or ω phase, demonstrating pre-phase transformation tendency. The study of the precipitation during thermomechanical processing at higher temperature in the α+β region revealed that discontinuous equiaxed or short rod shaped α precipitates (1~2μm) mainly form on the high angle and low angle β grain boundaries but seldom in β grain interiors, forming the “necklace” microstructure. The Burgers orientation relationship (BOR) between the α and β phases is destroyed gradually by the deformation. The BOR deviation of grain boundary α is larger than that of intragranular α. The deviation from the BOR increases both with the increasing strain and decreasing strain rate. During the deformation at the lower temperature in the α+β region, the α precipitates exhibit different morphologies: such as lamellar α, equiaxed α and irregular α depending on their localization. Within the slip bands, equiaxed α/β grains which do not respect the BOR are present. However, between the bands, lamellar α and β phases maintaining the BOR are distributed alternately. In that last case a strong variant selection is observed as only the two or three variants that form are those which can accommodate the macroscopic deformation. Comparatively, in absence of compression all 12 variants are formed. The β→α phase transformation is retarded during the hot compression at higher temperature region, which is attributed to the competition between softening and phase transformation. On the contrary, it is promoted during compression at lower temperature region due to the more inducted deformation defects acting as α phase nucleation sites and due to accelerating growth of α precipitates and retarded softening. Dislocation slip is the leading deformation mechanism for the Ti-5553 alloy. Under the lower temperature deformation condition, single or multiple-slip bands with two or three different activated slip systems would form during the hot deformation process. Identification of these slip systems have been done by trace analysis. These results provide new insights into the structural nature of β metastable phase and valuable reference for β→α phase transformation during thermo-mechanical treatment in metastable β titanium alloys

The thesis entitled “Organic fluorine in crystal engineering: Consequences on molecular and supramolecular organization” consists of six chapters. The main theme of the thesis is to address the role of substituted fluorine atoms in altering the geometrical and electronic features in organic molecules and its subsequent consequences on crystal packing. The thesis is divided into three parts. Part I deals with compounds that are liquids under ambient conditions, crystal structures of which have been determined by the technique of in situ cryocrystallography. Part II demonstrates the utilization of in situ cryocrystallography to study kinetically trapped metastable crystalline phases that provide information about crystallization pathways. In part III, crystal structures of a series of conformationally flexible molecules are studied to evaluate the consequences of fluorine substitution on the overall molecular conformation. The genesis and stabilization of a particular molecular conformation has been rationalized in terms of variability in intermolecular interactions in the crystalline state. Part I. In situ cryocrystallography: Probing the solid state structures of ambient condition liquids. Chapter 1 discusses the crystal structures of benzoyl chloride and its fluorinated analogs. These compounds have been analysed for the propensity of adoption of Cl···O halogen bonded dimers and catemers. The influence of conformational and electronic effects of sequential fluorination on the periphery of the phenyl ring has been quantified in terms of the most positive electrostatic potential, VS,max (corresponding to σ-hole) on the Cl-atom. It is shown that fluorine also exhibits “amphoteric” nature like other heavier halogens, particularly in presence of electron withdrawing groups. Although almost all the derivatives pack through C–H···O, C–H···F, C–H···Cl, Cl···F, C–H···π and π···π interactions, the compound 2,3,5,6-tetrafluorobenzoyl chloride exhibited a not so commonly observed Cl···O halogen bonded catemer. On the other hand, the proposed Cl···O mediated dimer is not observed in any of the structures due to geometrical constraints in the crystal lattice. Chapter 2 presents the preferences of fluorine to form hydrogen bond (C–H···F) and halogen bonds (X···F; X= Cl, Br, I). Crystal structures of all three isomers of chloro-, bromo-and iodo-fluorobenzene have been probed in order to gain insights into packing interactions preferred by fluorine and other heavier halogens. It has been observed that homo halogen…halogen (Cl···Cl, Br···Br and I···I) contacts prevail in most of the structures with fluorine being associated with the hydrogen atom forming C–H···F hydrogen bond. The competition between homo and hetero halogen bonds (I···I vs I···F) is evident from the packing polymorphism exhibited by 4-iodo fluorobenzene observed under different cooling protocols. The crystal structures of pentafluoro halo (Cl, Br, I) benzenes were also determined in order to explore the propensity of formation of homo halogen bonds over hetero halogen bonds. Different dimeric and catemeric motifs based on X···F and F···F interactions were observed in these structures. Chapter 3 focuses on the effect of different cooling protocols in generating newer polymorphs of a given liquid. The third polymorph (C2/c, Z'=6) of phenylacetylene was obtained by sudden quenching of the liquid filled in capillary from a hot water bath (363 K) to the nitrogen bath (< 77 K). Also, different polymorphs were obtained for both 2¬fluoro phenylacetylene (Pna21, Z'=1) and 3-fluoro phenylacetylene (P21/c, Z'=3) when crystallized by sudden quenching in contrast to the generally followed method of slow cooling which results in isostructural forms (P21, Z'=1). The rationale for these kinetically stable “arrested” crystalline configurations is provided in part II of the thesis. Part II. Tracing crystallization pathways via kinetically captured metastable forms. Chapter 4 explains the utilization of the new approach of sudden quenching of liquids (detailed in chapter 3) to obtain kinetically stable (metastable) crystalline phases that appear to be closer to the unstructured liquids. Six different examples namely, phenylacetylene, 2-fluorophenylacetylene, 3-fluorophenylacetylene, 4-fluorobenzoyl chloride, 3-chloro fluorobenzene and ethyl chloroformate are discussed in this context. In each case, different polymorphs were obtained when the liquid was cooled slowly (100 K/h) and when quenched sharply in liquid nitrogen. The relationship between these metastable forms and the stable forms (obtained by slow cooling) combined with the mechanistic details of growth of stable forms from metastable forms provides clues about the crystallization pathways. Part III. Conformational analysis in the solid state: Counterbalance of intermolecular interactions with molecular and crystallographic symmetries. Chapter 5 describes the crystal structures of a series of conformationally flexible molecules namely, acetylene and diacetylene spaced aryl biscarbonates and biscarbamates. While most of the molecules adopt commonly anticipated anti (transoid) conformation, some adopt unusual cisoid and gauche conformations. It is shown that the unusually twisted conformation of one of the compounds [but-2-yne-bis(2,3,4,5,6¬pentafluorocarbonate)] is stabilized mainly by the extraordinarily short C–H···F intermolecular hydrogen bond. The strength of this rather short C–H···F hydrogen bond has been authenticated by combined single crystal neutron diffraction and X-ray charge density analysis. It has also been shown that the equi-volume relationship of H-and F-atoms (H/F isosterism) can be explored to access various possible conformers of a diacetylene spaced aryl biscarbonate. While biscarbonates show variety of molecular conformations due to absence of robust intermolecular interactions, all the biscarbamates adopt anti conformation where the molecules are linked with antiparallel chains formed with N–H···O=C hydrogen bonds. Chapter 6 presents a unique example where the commonly encountered crystallographic terms namely, high Z' structure, polymorphism, phase transformation, disorder, isosterism and isostructuralism are witnessed in a single molecular species (parent compound benzoylcarvacryl thiourea and its fluorine substituted analogs). The origin of all these phenomenon has been attributed to the propensity of formation of a planar molecular dimeric chain mediated via N–H···O [R2 (12)] and N–H···S [R2 (8)] dimers.