No description available.

After introducing fundamentals of catalysis with noble metal surfaces especially Pt metal for CO oxidation and subsequent developments on nano-crystalline Pt metals supported on oxide supports, an idea of Pt ion in reducible oxide supports acting as adsorption sites is proposed in chapter 1. Idea of red-ox cycling of an ion in an oxide matrix is presented taking Cu ion in YBa2Cu3O7 as an example. Noble metal ions in reducible oxides such as CeO2 or TiO2 acting as adsorption sites and hence a red-ox catalyst was arrived at from chemical considerations. Among several reducible oxide supports, TiO2 was chosen from crystal structure and electronic structure considerations. A good redox catalyst for auto exhaust and related applications should have high oxygen storage capacity (OSC). Any new material that can work as a redox catalyst should be tested for its OSC. Therefore we designed and fabricated a temperature programmed reduction by hydrogen (H2¬TPR) system to measure OSC. This is presented in chapter 2. We have synthesized a number of oxides by solution combustion method. Structures were determined by powder XRD and Rietveld refinement methods. Fe2O3, Fe2-xPdxO3-δ, Cu1-xMnAl1+xO4, LaCoO3, LaCo1-xPdxO3-δ, CeO2, Ce1¬xPdxO2-δ, TiO2, Ti1-xPdxO2-δ and many other oxide systems were synthesized and their structures were determined. OSC of these systems were determined employing the H2/TPR system. TPR studies were carried out for several redox cycles in each case. Except Pd ion substituted CeO2 and TiO2 other oxide systems decomposed during redox cycling. Pd ion substituted TiO2 gave highest OSC and also it was stable paving way to choose this system for further study. In chapter 3, we have described lattice oxygen of TiO2 activation by the substitution of Pd ion in its lattice. Ti1-xPdxO2-x (x = 0.01 to 0.03) have been synthesized by solution combustion method crystallizing in anatase TiO2 structure. Pd is in +2 oxidation state and Ti is in +4 oxidation state in the catalyst as seen by XPS. Pd is more ionic in TiO2 lattice compared to Pd in PdO. Oxygen storage capacity defined by ‘amount of oxygen that is used reversibly to oxidize CO’ is as high as 5100 μmol/g of Ti0.97Pd0.03O1.97. Oxygen is extracted by CO to CO2 in absence of feed oxygen even at room temperature. Rate of CO oxidation is 2.75 μmol.g-1.s-1 at 60 0C over Ti0.97Pd0.03O1.97 and C2H2 gets oxidized to CO2 and H2O at room temperature. Catalyst is not poisoned on long time operation of the reactor. Such high catalytic activity is due to activated lattice oxygen created by the substitution of Pd ion as seen from first-principles density functional theory (DFT) calculations with 96 atom supercells of Ti32O64, Ti31Pd1O63, Ti30Pd2O62 and Ti29Pd3O61. The compounds crystallize in anatase TiO2 structure with Pd2+ ion in nearly square planar geometry and TiO6 octahedra are distorted by the creation of weakly bound oxygens. Structural analysis of Ti31Pd1O63 which is close to 3% Pd ion substituted TiO2 shows that bond valence of oxygens associated with both Ti and Pd ions in the lattice is 1.87. A low bond valence of oxygen is characteristic of weak oxygen in the lattice compared to oxygens with bond valence 2 and above in the same lattice. Thus, the exact positions of activated oxygens have been identified in the lattice from DFT calculations. Pt has two stable valencies: +2 and +4. Ti ion in TiO2 is in +4 state. Is it possible to substitute Pt exclusively in +2 or +4 state in TiO2? Implications are that Pt in +2 will have oxide ion vacancies and Pt in +4 states will not have oxide ion vacancies. Indeed we could synthesize Pt ion substituted TiO2 with Pt in +2 and +4 states by solution combustion method. In chapter 4, we have shown the positive role of an oxide ion vacancy in the catalytic reaction. Ti0.97Pt2+0.03O1.97 and Ti0.97Pt4+0.03O2 have been synthesized by solution combustion method using alanine and glycine as the fuels respectively. Both are crystallizing in anatase TiO2 structure with 15 nm average crystallite size. X-ray photoelectron spectroscopy (XPS) confirmed Pt ions are only +2 state in Ti0.97Pt0.03O1.97 (alanine) and only in +4 state in Ti0.97Pt0.03O2 (glycine). CO oxidation rate with Ti0.97Pt2+0.03O1.97 is over 10 times higher compared to Ti0.97Pt4+0.03O2. The large shift in 100 % hydrocarbon oxidation to lower temperature was observed by Pt2+ ion substituted TiO2 from that by Pt4+ ion substituted TiO2. After reoxidation of the reduced compound by H2 as well as CO, Pt ions are stabilized in mixed valences, +2 and +4 states. The role of oxide ion vacancy in enhancing catalytic activity has been demonstrated by carrying out the CO oxidation and H2 + O2 recombination reaction in presence and in absence of O2. There is no deactivation of the catalyst by long time CO to CO2 catalytic reaction. We analyzed the activated lattice oxygens upon substitution of Pt2+ ion and Pt4+ ion in TiO2, using first-principles density functional theory (DFT) calculations with supercells Ti31Pt1O63, Ti30Pt2O62, Ti29Pt3O61 for Pt2+ ion substitution in TiO2 and Ti31Pt1O64, Ti30Pt2O62, Ti29Pt3O61 for Pt4+ ion substitution in TiO2. We find that the local structure of Pt2+ ion has a distorted square planar geometry and that of Pt4+ ion has an octahedral geometry similar to Ti4+ ion in pure TiO2. The change in coordination of Pt2+ ion gives rise to weakly bonded oxygens and these oxygens are responsible in high rates of catalytic reaction. Thus, the high catalytic activity results from synergistic roles of oxide ion vacancy and weakly bonded lattice oxygen. In chapter 5, we have shown high rates of H2 + O2 recombination reaction by Ti0.97Pd0.03O1.97 catalyst coated on honeycomb monolith made up of cordierite material. This catalyst was coated on γ¬Al2O3 coated monolith by solution combustion method using dip-dry-burn process. This is a modified conventional method to coat catalysts on honeycombs. Formation of Ti0.97Pd0.03O1.97 catalyst on monolith was confirmed by XRD. Form the XPS spectra of Pd(3d) core level in Ti1-xPdxO2-δ, Pd ion is the formed to be +2 state. Ti0.97Pd0.03O1.97 showed high rates of H2 + O2 recombination compared to 2 at % Pd(metal)/γ-Al2O3, Ce0.98Pd0.02O2-δ, Ce0.98Pt0.02O2-δ, Ce0.73Zr0.25Pd0.02O2-δ and Ti0.98Pd0.02O1.98. Activation energy of H2 + O2 recombination reaction over Ti0.97Pd0.03O1.97 is 7.8 kcal/mole. Rates of reaction over Ti0.97Pd0.03O1.97 are in the range of 10 – 20 μmol/g/s at 60 0C and 4174 h-1 space velocity. Rate is orders of magnitude higher compared to noble metal catalysts. From the industrial point of view, solvent-free hydrogenation of aromatic nitro compounds to amines at nearly 1 bar pressure is an important process. In chapter 6, we showed that Ti0.97Pd0.03O1.97 is a good –nitro to –amine conversion catalyst under solvent-free condition at 1.2 – 1.3 bar H2 pressure. Nitrobenzene, p-nitrotoluene and 2-chloro-4-nitrotoluene are taken for the catalytic reduction reaction. The amine products were analyzed by gas chromatography and mass spectrometry (GCMS). Further, confirmation of compounds was done by FTIR, 1H NMR and 13C NMR. In presence of alcohol as solvent, 100% conversion of aromatic nitro compounds to amines took place at higher temperature and it required more times. In n-butanol solvent, 100% conversion of nitrobenzene and p-nitrotoluene occurred within 10 h and 12 h at 105 °C respectively. We have compared solvent-free reduction of p-nitrotoluene over different catalysts at 90 °C. Catalytic activity for reduction of p¬nitrotoluene over Ti0.97Pd0.03O1.97 is much higher than that reaction over 3 atom % Pd on TiO2 and Pd metal. Turnover frequencies (TOF) for nitrobenzene and 2-chloro-4-nitrotoluene conversion are 217 and 20 over Ti0.97Pd0.03O1.97 respectively. With increase of temperature, TOF of aromatic nitro compound reduction is also increased. We have compared the solvent-free reduction of aromatic nitro compound over Ti0.97Pd0.03O1.97 with others in the literature. Upto 3 cycles of reduction reaction, there was no degradation of Ti0.97Pd0.03O1.97 catalyst and stability of catalyst structure was analyzed by XRD, XPS and TEM images. Catalyst is stable under reaction condition and the structure is retained with Pd in +2 state. Finally, we have proposed the mechanism of -nitro group reduction reaction based on the structure of Ti0.97Pd0.03O1.97. Instead of handling nano-crystalline materials we proceeded with coating our catalysts on cordierite honeycombs. In chapter 7, we have shown high catalytic activity towards Heck reaction over Ce0.98Pd0.02O2-δ and Ti0.97Pd0.03O1.97 coated on cordierite monolith. XRD patterns of Ce0.98Pd0.02O2¬δ coated on cordierite monolith were indexed to fluorite structure. Heck reaction of aryl halide with olefins over Ce0.98Pd0.02O2-δ and Ti0.97Pd0.03O1.97 coated on cordierite monolith were carried out at 120 °C. The products were first analyzed by GCMS and for the confirmation of compounds, we have recorded 1H NMR and 13C NMR. Heck reaction was carried out with different solvents and different bases for choosing the good base and a solvent. Hence, we have chosen K2CO3 as base and N,N¬dimethylformamide (DMF) as solvent. We have compared the rates of Heck reactions over these two catalysts and Ti0.97Pd0.03O1.97 catalyst showed much higher catalytic activity than Ce0.98Pd0.02O2-δ. With increase of temperature from 65 °C to 120 °C, the catalytic activity of Ti0.97Pd0.03O1.97 on Heck reaction is also increased. The catalyst was reused for next Heck reaction without significant loss of activity. A mechanism for Heck reaction of aryl halide with alkyl acrylate has been proposed based on the structure of Ti0.97Pd0.03O1.97. In chapter 8, we have provided a critical review of the work presented in the thesis. Critical issues such as noble metal ion doping in TiO2 vs noble metal ion substitution, difficulty of proving the substitution of low % noble metal ion in TiO2, need for better experimental methods to study noble metal ion in oxide matrix have been discussed. Finally, conclusions of the thesis are presented.

Este trabalho teve como objetivo investigar eletrocatalisadores de baixo custo à base de carbeto de tungstênio, carbono e ferro submetidos a diferentes processos de nitretação quanto à atividade catalítica para reação de redução do oxigênio (RRO) nos eletrólitos ácido e alcalino. Os catalisadores foram divididos em três séries distintas, a primeira compreendendo aqueles onde houve variação da carga de carbeto de tungstênio em relação ao suporte de carbono, que foram impregnados com o complexo Fe2+(2,4,6-Tris(2-piridil)-1,3,5-Triazina)2, [Fe(TPTZ)2]2+ e tratados em duas temperaturas diferentes, 700 e 800 oC em atmosfera de nitrogênio. Na segunda série foi mantida constante a carga de carbeto de tungstênio (30% de W/C, m/m) sendo que esta mescla foi preparada usando carbonos dopados previamente com três fontes distintas de nitrogênio (HNO3, NH3 e HNO3/NH3); isto foi seguido pela incorporação do complexo Fe[TPTZ]2+ e pelos mesmos tratamentos térmicos acima mencionados. Na terceira série, os eletrocatalisadores foram preparados com três tipos de carbonos (Vulcan, Ketjenblack e Monarch), aos quais foi incorporado o complexo Fe[TPTZ]2+, seguido pelo tratamento térmico a 800 °C em atmosfera de nitrogênio e então por dopagem com amônia a 950 °C. As três séries de eletrocatalisadores sintetizados neste trabalho foram cuidadosamente caracterizadas por espectroscopia infra-vermelho e UV-Visível, difratometria de raio-x, microscopia eletrônica de transmissão, energia dispersiva de raios-x, espectroscipia Raman, espectroscopia fotoeletrônica de raios-x. As investigações eletroquímicas foram realizadas por voltametria cíclica (VC) e pelo levantamento de curvas de polarização de estado estacionário para a RRO, usando a técnica de eletrodo de disco/anel rotatório, com materiais catalíticos formando filmes finos depositados no eletrodo de disco. Nas três séries de catalisadores foram desenvolvidos materiais com bom desempenho para a RRO. Nos estudos da primeira série de catalisadores, notou-se que o material mais ativo foi aquele formado por WC-FeNx/C com 30 % de W/C e 5% de Fe pirolisado a 800 °C. Na segunda série foi observado que os desempenhos dos catalisadores variaram de acordo com o tipo de protocolo de nitretação, presença de ferro e temperatura de tratamento térmico. Em eletrólito alcalino, os eletrocatalisadores apresentaram maiores desempenhos, que resultaram bastante próximos em relação ao do catalisador de Pt dispersa em carbono usado como referência. Na terceira série de eletrocatalisadores investigados, verificou-se que o melhor desempenho obtido foi com o catalisador com carbono Monarch com amônia, cuja atividade catalítica resultou superior à dos demais, devido ao maior número de estruturas ativas FeNx e N/C formadas pelo tratamento com amônia. Os resultados nos meios ácido e alcalino para a primeira e segunda séries de eletrocatalisadores sugerem a ocorrência de um mecanismo indireto (2e- + 2e-), ou seja, em meio ácido (alcalino) primeiro o O2 reduz para H2O2 (HO2 ) e depois de H2O2 (HO2 ) para H2O. Os sítios predominantemente envolvidos na catálise da reação são WC e FeNx em meio ácido e WC e N/C em meio alcalino. Finalmente, para a terceira série de eletrocatalisadores o mecanismo reacional em meio ácido envolve um mecanismo direto de 4e-, com participação importante dos sítios ativos de Fe-N2. / This work aims to investigate low cost electrocatalysts based on tungsten carbide, carbon and iron submitted to different nitriding processes for the catalytic activity for the oxygen reduction reaction (ORR) in acid and alkaline electrolytes. The catalysts were divided into three distinct series, the first one comprising those with different tungsten carbide loads with respect to the carbon support, which were impregnated with the Fe2+ (2,4,6-Tris (2-pyridyl) - 1,3,5-triazine)2, [Fe (TPTZ)]2+, complex and treated at two different temperatures, 700 and 800 oC in nitrogen atmosphere. In the second series, the tungsten carbide load (30% W/C, m/m) was kept constant but this mixture was prepared using previously doped carbons using three different sources of nitrogen (HNO3, NH3 and HNO3/NH3); this was followed by the incorporation of the Fe[TPTZ]2+ complex and by the same heat treatments as mentioned above. In the third series, the electrocatalysts were prepared with three carbon types (Vulcan, Ketjenblack and Monarch), to which the Fe[TPTZ]2+ complex was added, followed by heat treatment at 800 °C under nitrogen and then by nitriding using a flow of ammonia at 950 °C. The three series of electrocatalysts synthesized in this work were carefully characterized by infra-red and UV-Visible spectroscopy, x-ray diffraction, transmission electron microscopy, x-ray energy dispersive, Raman spectroscopy, x-ray photoelectron spectroscopy. The electrochemical investigations were performed by cyclic voltammetry (CV) and by measurements of steady-state polarization curves for ORR using rotating ring-disc electrode technique, with catalytic materials forming thin films deposited on the disc. In the three catalyst series, materials with good performance for the ORR were developed. In the studies of the first series of catalysts, it was seen that the most active material was that formed by WC-FeNx/C with 30%W/C and 5% Fe pyrolyzed at 800 ° C. In the second series it was observed that the performances of the catalysts varied according to the type of nitriding protocol, presence of iron and temperature of heat treatment. The electrocatalysts showed higher performances in alkaline electrolyte, which were very close to that of a reference Pt/C catalyst. In the third series of electrocatalysts, the best performance was obtained with the Monarch carbon catalyst heat-treated with ammonia, whose catalytic activity was higher than all others, due to the greater number of FeNx and N/C active structures formed by the treatment with ammonia. The results in acidic and alkaline conditions for the first and second series of electrocatalysts suggest the occurrence of an indirect ORR mechanism (2e- + 2e-), that is, in acid (alkaline) media first O2 is reduced to H2O2 (HO2) followed by the reduction of H2O2 (HO2). The active sites predominantly involved in the reaction electrocatalysis are WC and FeNx in acid media and WC e N/C in alcaline media. Finally, for the third series of electrocatalysts, the acidic reaction involves a direct 4e- mechanism, having important participation of the Fe-N2 active sites.

In dieser Dissertation wurden die ungewöhnlichen und einzigartigen Eigenschaften von Edelmetall-Clustern untersucht, die durch Quantum-Confinement im Sub-Nanometer-Bereich entstehen. Dabei zeigt sich, dass die chemischen und physikalischen Eigenschaften und damit die Funktionen nicht vom Festkörper abgeleitet werden können und stark von der Anzahl der Atome abhängen. Die erzielten theoretischen Ergebnisse wurden in enger Zusammenarbeit mit experimentell arbeitenden Partnergruppen erzielt. Dabei hat sich gezeigt, dass durch die enge Kooperation zwischen Theorie und Experiment ein tiefes Verständnis von fundamentalen Prozessen und den zugrunde liegenden Mechanismen erlangt werden kann. Im Rahmen dieser Dissertation wurden die Reaktivität von geladenen Goldoxid-Clustern in der Gasphase, die ultraschnelle Dynamik von Edelmetall-Clustern und deren Komplexen sowie die optischen Eigenschaften von kleinen, deponierten Silber-Clustern untersucht und damit Beiträge geliefert, die einzigartigen Eigenschaften von Edelmetall-Clustern im Zusammenhang mit der heterogenen Katalyse und Nano-Optik besser zu verstehen. / In this thesis, the unique novel properties of noble metal clusters which arise in the sub-nanometer size regime due to quantum confinement have been theoretically explored. It has been demonstrated that by adding or removing a single atom the chemical and physical properties and functionality of noble-metal clusters can strongly change. The theoretical results have been derived in close cooperation with experimental findings of partner groups demonstrating that by joint theoretical and experimental efforts thorough understanding of fundamental processes and underlying mechanisms can be achieved. This thesis addresses the reactivity of charged gas-phase gold-oxide clusters in the context of the heterogeneous gold nano-catalysis, the ultrafast dynamical properties of noble-metal clusters and their complexes, and the optical properties of silver clusters at surfaces.

The thesis consists of four parts of which part 1 presents a brief overview of nanomaterials. Parts 2, 3 and 4 contain results of investigations of graphene, nanofilms of noble metal nanoparticles and ZnO nanostructures respectively. Investigations of graphene are described in Part 2 which consists of six chapters. In Chapter 2.1, changes in the electronic structure and properties of graphene induced by molecular charge-transfer have been discussed. Chapter 2.2 deals with the results of a study of the interaction of metal and metal oxide nanoparticles with graphene. Electrical and dielectric properties of graphene-polymer composites are presented in Chapter 2.3. Chapter 2.4 presents photo-thermal effects observed in laser-induced chemical transformations in graphene and other nanocarbons system. Chapter 2.5 describes the mechanical properties of polymer matrix composites reinforced by fewlayer graphene investigated by nano-indentation. The extraordinary synergy found in the mechanical properties of polymer matrix composites reinforced with two nanocarbons of different dimensionalities constitute the subject matter of Chapter 2.6. Investigations of noble metal nanoparticles have been described in Part 3. In Chapter 3.1, ferromagnetism exhibited by nanoparticles of noble metals is discussed in detail while Chapter 3.2 deals with surface-enhanced Raman scattering (SERS) of molecules adsorbed on nanocrystalline Au and Ag films formed at the organic–aqueous interface. Factors affecting laser-excited photoluminescence from ZnO nanostructures are examined in great detail in Part 4.

Abstract The harmful emissions of chlorinated volatile organic compounds (CVOCs) originate only from man-made sources. CVOCs are used in a variety of applications from pharmaceuticals production to decaffeination of coffee. Currently, CVOC emissions are limited by strict legislation. For these reasons, efficient CVOC abatement technologies are required. Catalytic oxidation is very promising option for this purpose, since catalysts can be tailored to each case to maximize the efficiency and minimize the formation of unwanted products, such as dioxins or Cl2. The goal of this thesis was to study the role of the physico-chemical properties of catalysts in dichloromethane (DCM) oxidation. To reach the aim, several catalytic materials were prepared and characterized, and their performance was tested in total oxidation of DCM. The catalytic materials used were powders of four single metal oxides (γ-Al2O3, TiO2, CeO2, MgO), three mixed oxides (Al2O3-xSiO2) washcoated on a cordierite monolith and four active phases (Pt, Cu, V, Mn). At first, support properties were studied. It was found that the DCM conversion and HCl production are dependent on support acidity when the studied single oxides are considered. The best DCM conversions and HCl yields were observed with the support having the highest total acidity (γ-Al2O3). Further, the quality of the by-products formed was dependent on the type of the acid sites present on the support surface. Secondly, the impregnation of the active compound was observed to improve the selectivity of the material. From the tested active phases, Pt presented the best performance, but also V2O5 and CuO showed almost equal performances. Especially CuO supported on γ-Al2O3, that had less formation of by-products and is less toxic than V-containing oxides, seems to be a promising alternative to Pt. Concerning stability, no deactivation was observed after 55h of testing of Pt/Al2O3. Furthermore, in the used reaction conditions, the formation of CuCl2 is not thermodynamically favoured. Finally, the good characteristics of the powder form catalysts were successfully transferred to the monolith. The performance of the Pt/90Al2O3-10SiO2 catalyst in DCM oxidation was improved when the channel density was increased due to an increase in geometric surface area and mechanical integrity factor, and a decrease in open fraction area and thermal integrity factor. / Tiivistelmä Haitallisten kloorattujen orgaanisten yhdisteiden (CVOC) päästöt ovat ihmisten aiheuttamia. CVOC-yhdisteitä käytetään mm. liuottimina lääkeaineiden valmistuksessa ja kofeiinin poistossa. Nykyisin CVOC-päästöjä rajoitetaan tiukalla lainsäädännöllä. Näistä syistä tehokas CVOC-yhdisteiden käsittelymenetelmä on tarpeen. Katalyyttinen hapetus on hyvä vaihtoehto tähän tarkoitukseen, koska katalyytit voidaan räätälöidä niin, että puhdistuksen tehokkuus saadaan maksimoitua samalla kun ei-haluttujen tuotteiden, kuten dioksiinit ja kloorikaasu, muodostuminen voidaan minimoida. Tämän väitöskirjatyön tavoitteena oli selvittää katalyyttien fysikaalis-kemiallisten ominaisuuksien yhteyksiä dikloorimetaanin (DCM) hapetukseen. Tavoitteen saavuttamiseksi valmistettiin useita katalyyttejä, jotka karakterisoitiin ja testattiin DCM:n kokonaishapetuksessa. Työssä tutkittiin neljää jauhemaista metallioksidia (γ-Al2O3, TiO2, CeO2 ja MgO), kolmea metallioksidiseosta (Al2O3-xSiO2), jotka pinnoitettiin kordieriittimonoliitille, sekä neljää aktiivista ainetta: Pt, Cu, V and Mn. Aluksi työssä keskityttiin tukiaineiden ominaisuuksiin. Työn tulokset osoittivat, että DCM:n konversio ja HCl:n tuotanto ovat riippuvaisia tukiaineen happamuudesta. Paras tulos saavutettiin alumiinioksidilla, jolla oli korkein kokonaishappamuus. Lisäksi havaittiin, että sivutuotteiden laatu riippuu tukiaineen pinnalla olevien happopaikkojen tyypistä. Aktiivisen aineen impregnointi tukiaineeseen paransi materiaalin selektiivisyyttä. Tutkituista aineista Pt osoittautui parhaimmaksi, mutta myös V2O5 ja CuO olivat lähes yhtä hyviä. Erityisesti CuO-katalyytti, joka tuotti vähemmän sivutuotteita ja joka on materiaalina vähemmän haitallinen kuin V2O5, osoittautui lupaavaksi jalometallikatalyyttien korvaajaksi. Materiaalien stabiilisuuteen liittyen Pt/Al2O3-katalyytin toiminnassa ei havaittu muutoksia 55 tunnin testauksen jälkeen. Lisäksi CuCl2:n muodostuminen ei mallinnuksen mukaan ole termodynaamisesti todennäköistä tutkituissa reaktio-olosuhteissa. Jauhemaisen katalyytin hyvät ominaisuudet pystyttiin pinnoituksessa siirtämään monoliittirakenteiseen katalyyttiin. Pt/90Al2O3-10SiO2 -katalyytin aktiivisuus DCM:n hapetuksessa tehostui, kun monoliitin aukkoluku kasvoi aiheutuen suuremmasta geometrisestä pinta-alasta ja mekaanisesta eheystekijästä sekä pienemmästä avoimen pinnan osuudesta ja termisestä eheystekijästä.

Les réponses optiques d'agrégats de métaux nobles sont caractérisées par une absorption intense, situées dans le domaine UV-Visible, et appelée plasmon de surface localisé. Pour des particules de plusieurs nanomètres de diamètre, le phénomène de plasmon peut être interprété par des modèles semi-classiques ou classiques comme la théorie de Mie, mais ces modèles trouvent leur limite lorsque la taille du système diminue. La théorie de la fonctionnelle de la densité dépendante du temps (TDDFT) est une approche entièrement quantique qui permet d'appréhender le phénomène de plasmon en reproduisant la réponse optique de petits agrégats d'argent, composés de quelques atomes à quelques centaines d'atomes. Dans ce contexte, nous avons réalisé des calculs TDDFT avec une fonctionnelle de type Range-Separated-Hybrid (RSH) sur des agrégats contenant entre 8 et 147 atomes d'argent. Les spectres obtenus sont en excellent accord avec les données expérimentales et les réponses optiques calculées perme ttent de retrouver les prédictions du modèle en couches. Nous présentons des outils permettant d'identifier et de caractériser les excitations plasmoniques dans le formalisme de la TDDFT. Les effets de l'environnement sur la réponse optique des agrégats sont également étudiés, avec notamment la présentation d'une méthodologie permettant de reproduire les spectres mesurés sur des agrégats d'argent piégés dans des matrices de gaz rare. Les effets de l'oxydation et les effets induits par une matrice de silice sur la réponse optique des agrégats sont également étudiés / Optical responses of noble metal clusters are characterized by a strong absorption in the UV-Visible range called localized surface plasmon. For clusters of several nanometers, the plasmon phenomenon can be interpreted by semi-classical or classical model, as the Mie theory, but those models can not describe the optical response of small-size clusters. The time dependent density functional theory (TDDFT) is a quantum method that allow to understand the plasmon phenomenon by reproducing the optical response of small silver cluster, made of a few tens or hundreds atoms. In this context, we performed TDDFT calculation using Range-Separated Hybrid (RSH) functionals over cluster containing between 8 and 147 silver atoms. The obtained spectra are in excellent agreement with the experimental ones and the calculated optical response allows to recover the shell model prediction. We present some tools that allow to identify and characterize plasmonic excitations within the TDDFT framework. The effect of the surrounding medium over the optical response of clusters are studied, in particular we will present a methodology that allow to reproduce spectra measured over clusters trapped in rare gas matrix. The effects of the oxidation and the effects induced by a silica matrix over the optical response of clusters are also studied

Este trabalho teve como objetivo investigar eletrocatalisadores de baixo custo à base de carbeto de tungstênio, carbono e ferro submetidos a diferentes processos de nitretação quanto à atividade catalítica para reação de redução do oxigênio (RRO) nos eletrólitos ácido e alcalino. Os catalisadores foram divididos em três séries distintas, a primeira compreendendo aqueles onde houve variação da carga de carbeto de tungstênio em relação ao suporte de carbono, que foram impregnados com o complexo Fe2+(2,4,6-Tris(2-piridil)-1,3,5-Triazina)2, [Fe(TPTZ)2]2+ e tratados em duas temperaturas diferentes, 700 e 800 oC em atmosfera de nitrogênio. Na segunda série foi mantida constante a carga de carbeto de tungstênio (30% de W/C, m/m) sendo que esta mescla foi preparada usando carbonos dopados previamente com três fontes distintas de nitrogênio (HNO3, NH3 e HNO3/NH3); isto foi seguido pela incorporação do complexo Fe[TPTZ]2+ e pelos mesmos tratamentos térmicos acima mencionados. Na terceira série, os eletrocatalisadores foram preparados com três tipos de carbonos (Vulcan, Ketjenblack e Monarch), aos quais foi incorporado o complexo Fe[TPTZ]2+, seguido pelo tratamento térmico a 800 °C em atmosfera de nitrogênio e então por dopagem com amônia a 950 °C. As três séries de eletrocatalisadores sintetizados neste trabalho foram cuidadosamente caracterizadas por espectroscopia infra-vermelho e UV-Visível, difratometria de raio-x, microscopia eletrônica de transmissão, energia dispersiva de raios-x, espectroscipia Raman, espectroscopia fotoeletrônica de raios-x. As investigações eletroquímicas foram realizadas por voltametria cíclica (VC) e pelo levantamento de curvas de polarização de estado estacionário para a RRO, usando a técnica de eletrodo de disco/anel rotatório, com materiais catalíticos formando filmes finos depositados no eletrodo de disco. Nas três séries de catalisadores foram desenvolvidos materiais com bom desempenho para a RRO. Nos estudos da primeira série de catalisadores, notou-se que o material mais ativo foi aquele formado por WC-FeNx/C com 30 % de W/C e 5% de Fe pirolisado a 800 °C. Na segunda série foi observado que os desempenhos dos catalisadores variaram de acordo com o tipo de protocolo de nitretação, presença de ferro e temperatura de tratamento térmico. Em eletrólito alcalino, os eletrocatalisadores apresentaram maiores desempenhos, que resultaram bastante próximos em relação ao do catalisador de Pt dispersa em carbono usado como referência. Na terceira série de eletrocatalisadores investigados, verificou-se que o melhor desempenho obtido foi com o catalisador com carbono Monarch com amônia, cuja atividade catalítica resultou superior à dos demais, devido ao maior número de estruturas ativas FeNx e N/C formadas pelo tratamento com amônia. Os resultados nos meios ácido e alcalino para a primeira e segunda séries de eletrocatalisadores sugerem a ocorrência de um mecanismo indireto (2e- + 2e-), ou seja, em meio ácido (alcalino) primeiro o O2 reduz para H2O2 (HO2 ) e depois de H2O2 (HO2 ) para H2O. Os sítios predominantemente envolvidos na catálise da reação são WC e FeNx em meio ácido e WC e N/C em meio alcalino. Finalmente, para a terceira série de eletrocatalisadores o mecanismo reacional em meio ácido envolve um mecanismo direto de 4e-, com participação importante dos sítios ativos de Fe-N2. / This work aims to investigate low cost electrocatalysts based on tungsten carbide, carbon and iron submitted to different nitriding processes for the catalytic activity for the oxygen reduction reaction (ORR) in acid and alkaline electrolytes. The catalysts were divided into three distinct series, the first one comprising those with different tungsten carbide loads with respect to the carbon support, which were impregnated with the Fe2+ (2,4,6-Tris (2-pyridyl) - 1,3,5-triazine)2, [Fe (TPTZ)]2+, complex and treated at two different temperatures, 700 and 800 oC in nitrogen atmosphere. In the second series, the tungsten carbide load (30% W/C, m/m) was kept constant but this mixture was prepared using previously doped carbons using three different sources of nitrogen (HNO3, NH3 and HNO3/NH3); this was followed by the incorporation of the Fe[TPTZ]2+ complex and by the same heat treatments as mentioned above. In the third series, the electrocatalysts were prepared with three carbon types (Vulcan, Ketjenblack and Monarch), to which the Fe[TPTZ]2+ complex was added, followed by heat treatment at 800 °C under nitrogen and then by nitriding using a flow of ammonia at 950 °C. The three series of electrocatalysts synthesized in this work were carefully characterized by infra-red and UV-Visible spectroscopy, x-ray diffraction, transmission electron microscopy, x-ray energy dispersive, Raman spectroscopy, x-ray photoelectron spectroscopy. The electrochemical investigations were performed by cyclic voltammetry (CV) and by measurements of steady-state polarization curves for ORR using rotating ring-disc electrode technique, with catalytic materials forming thin films deposited on the disc. In the three catalyst series, materials with good performance for the ORR were developed. In the studies of the first series of catalysts, it was seen that the most active material was that formed by WC-FeNx/C with 30%W/C and 5% Fe pyrolyzed at 800 ° C. In the second series it was observed that the performances of the catalysts varied according to the type of nitriding protocol, presence of iron and temperature of heat treatment. The electrocatalysts showed higher performances in alkaline electrolyte, which were very close to that of a reference Pt/C catalyst. In the third series of electrocatalysts, the best performance was obtained with the Monarch carbon catalyst heat-treated with ammonia, whose catalytic activity was higher than all others, due to the greater number of FeNx and N/C active structures formed by the treatment with ammonia. The results in acidic and alkaline conditions for the first and second series of electrocatalysts suggest the occurrence of an indirect ORR mechanism (2e- + 2e-), that is, in acid (alkaline) media first O2 is reduced to H2O2 (HO2) followed by the reduction of H2O2 (HO2). The active sites predominantly involved in the reaction electrocatalysis are WC and FeNx in acid media and WC e N/C in alcaline media. Finally, for the third series of electrocatalysts, the acidic reaction involves a direct 4e- mechanism, having important participation of the Fe-N2 active sites.

La réponse optique de nanostructures métalliques est caractérisée par une amplification locale du champ électromagnétique appelée Résonance Plasmon de Surface (RPS) reliée à leur nature et leur morphologie. Pour étudier la réponse optique d’une nanoparticule unique, un dispositif ultra-sensible de spectroscopie à modulation spatiale utilisant une source de lumière blanche a été développé : il permet de mesurer la section efficace d’extinction absolue de nano-objets uniques sur un large domaine spectral (300-900 nm). Des images de microscopie électronique à transmission peuvent être obtenues indépendamment sur les mêmes objets. On a ainsi une corrélation directe entre la morphologie des nanoparticules et leur signature optique. Ce travail de thèse a permis d’une part de mettre en évidence les paramètres qui entrent en jeu dans le processus de vieillissement de nanoparticules uniques d’argent sous éclairement. En particulier, l’étude de nanocubes d’argent révèle une « sphérisation » et une photo-oxydation au cours du temps due à la partie UV du spectre. D’autre part, des mesures réalisées sur des doublets de nanocubes d’argent en interaction ont montré l’importance de la morphologie à l’interface entre les deux nanoparticules sur le couplage plasmonique. Pour une excitation lumineuse longitudinale, on observe, outre le décalage de la RPS vers les basses énergies lorsque la distance interparticule diminue, un dédoublement de cette bande de résonance. Des calculs théoriques réalisés avec la méthode DDA ont permis de corréler ce phénomène de dédoublement à des variations de courbure de surface dans la zone interparticule liées principalement au rognage des arêtes des cubes / The optical properties of noble metal nanoparticles are known to be dominated by the localized surface plasmon resonance (SPR) which is highly sensitive to the size of the particles, their shape, their environment, and eventually their chemical composition in the case of mixed systems. In order to study the optical response of a single supported metallic nanoparticle, a high sensitive spectroscopic setup using a white lamp (300-900 nm) has been developed in a transmission measurement configuration. This technique, the Spatial Modulation Spectroscopy, aims to detect the overall extinction of light by a nanoparticle. Moreover, the coupling of this technique with the direct observation of the particles by Transmission Electron Microscopy allows to get an unambiguous description of their optical response in relation with their exact morphology. In this work, the optical response of single silver nano-objects has been correlated with their morphology and their structure at a sub-nanometer scale. Time evolution of the optical response of single silver nanocubes under illumination was first investigated. We observed a “spherization” and a photo-oxidation due to the UV part of the light. Moreover, we studied pairs of cubic silver nanoantennas that showed a huge sensitivity of their optical response with the interparticle distance and their morphology. Indeed, the SPR is red-shifted with decreasing interparticle distance. One can also observe a striking splitting of the resonance for very low interparticle distances. Preliminary DDA calculations seem to show that the radius of curvature at the corners and edges of both cubes plays a key role in the splitting of the resonance

No description available.