Computer graphics has long been the foremost area of advancement in both the gaming and the motion picture industry. Nowadays, as computer graphics is getting difficult to advance any further, other areas begin to interest the developers. One of these areas is artificial intelligence. The gaming industry has begun to create far more intelligent virtual characters that no longer are as predictable as they used to be. Mixing character animation with intelligent agents techniques results in a vastly more interesting experience for the gamer as well as for the developer. This project focuses on introducing expectational behaviour and trust in intelligent virtual characters. The area is highly interesting as it enables a vastly more complex emotional structure for virtual agents than that of reactive, rational behaviour. Although expectations can indeed be rational, often they are not when it comes to humans. This project studies the effects of expectations on the emotional state of agents and the effect that the emotions have on the reasoning abilities and the action selection mechanism. It also examines how trust influences emotions and vice versa and how trust influences the action selection mechanism. One of the requirements of this work is that the computations concerning the triggering of emotions have to be done in real-time. While it is possible to do off-line computations for simulations (such as is often done for the movie industry), it is not what we desire here. It is our goal to create interesting virtual characters that can be interacted with in real-time. Therefore, also expectations and trust must be calculated and managed in real-time.

Assignment: The mission of the assignment is to map the four return flows with respect to returning volume, weight, frequency, pick up- and delivery points. Today Volvo CE has a lack of information that concerns their own Reverse logistic processes. It is hard for Volvo CE to see where changes need to be done, due to limited reliable sources. Purpose: The purpose with the study is to make the return flows easier, less expansive and more manageable for both Volvo and their dealers. Further, environmental issues have to be considered in order to find improvements of the returning routines. The analysis is done to bring forth a proposal that will contribute to less unnecessary transports and that also will make it possible to reduce cost. Result: A couple of improvement areas have been discovered, some of them are radical while others are incremental. The one thing they have in common is to make sure that the return flows are being handled and seen as one common flow rather then separately treated. Among the improvements these are some recommendations to Volvo CE: - Appoint special delivery point for warranty returns and make sure that the warranty routines are followed so that unnecessary transports can be reduced. - Store less cores for remanufacturing at the Core Hub. Cores that are not needed are not necessary to transport to the Core Hub. - Make better cost registrations and cost follow ups and evaluate customer satisfaction to be able to find improvement areas in the future.

This paper shows how instructions for the inspections of the lifting tools at Abetong were made. The most important is how the company can ensure that every lifting tool is inspected. The work was carried out at three of Abetongs factories. Abetong makes precast concrete elements, which makes them use liftingtools as a part of their daily work; most of the lifting tools are custom made for the concrete industry. A numeric system for the lifting tools was formed and partially implemented. A small investigation to find companies which could do the annual inspections was made. A specification for this was also written. An instruction for the daily inspection of the lifting tools was made. A signing list will be put up at each working area to ensure that the daily inspections are being done. The lifting yokes which lacks label will be risk analysed, this creates some questions about whether this is aloud.

Radio frequency ablation (RFA) is a commonly used minimally invasive method of treating liver cancer tumours which utilises RF current for heating tumour tissue up to a lethal temperature. RF current is generated by a power generator and applied to the tumour by an electrode which is inserted into the tumour either during percutaneous or open surgery. RFA is a method that has great advantages compared to traditional surgical resection of tumours due to minimal invasiveness, it can be used for a greater number of patients and enables repeated treatments. Even though there are many advantages coupled to RFA there are still some problems and difficulties associated with the method. One of these problems is the cooling effect from large vessel blood flow within the liver, the so called heat sink effect. The aim of this master thesis work has been to develop a theoretical finite element model of RFA within Comsol Multiphysics software. This theoretical model has been used to simulate blood perfusion effects on resulting ablation volume. The effects from different large vessel blood flow parameters has been investigated, these parameters are: blood flow velocity, blood vessel diameter and distance between blood vessel and RF electrode. A factorial design has been utilised to setup parameter levels for the different simulations. A linear- and a second degree regression model has been calculated based on simulation results. The parameter with largest impact on simulative ablation volume and the interaction effects between the parameters were determined from the regression model coefficients. In addition to this has two simulations been performed, modelling perfused- and unperfused liver tissue, in order to investigate the effects resulting from microvascular perfusion. The result shows that the parameter with largest impact on simulative ablation volume are the distance, it was also shown that there are a small interactional effects between diameter and distance, where a small distance increases the effect from a varying diameter. Modelled microvascular perfusion was shown to give a decrease in simulative ablation volume. A shortage of this master thesis work is the lack of experimental verification of the developed model.

<p>Olyckor sker vid övning med frifallslivbåtar. Detta borde gå att arbeta bort med bättre utrustning och bättre utbildning. Eftersom olyckor inträffar oftare vid övning ombord i fartygen än vid övning iland borde den senare biten vara mer avgörande: Vid övningar bör vikt läggas vid hur man spänner fast sig på ett korrekt sätt. Ovanstående är en del av vad denna undersökande studie handlar om. Vi har använt en kvalitativ metod för att reda ut frågor om riskerna med frifallslivbåtar. SOLAS ställer inga krav på att det skall finnas hjälpmedel för att underlätta att ta med sig skadade personer i frifallslivbåtar. De tester som genomförts med människor ombord i frifallslivbåtar har bara skett när det råder gynnsamma förhållanden. Med tanke på att fartyg utsätts både för sjöhävning och att båtarna kan komma att landa i vågor borde SOLAS kraven höjas. De livbåtssystem vi har, varken testas eller övas med i vågor. Att frifallslivbåtar i tanken är ett väldigt bra koncept som livräddningsutrustning råder det inga tvivel om, men den borde utvecklas vidare.</p> / <p>Accidents occur when exercising with free-fall lifeboats. This should be possible to avoid with better equipment and better education. Since accidents occur more often when exercise is performed aboard ships than ashore, the later part should be more decisive: During exercise the focus should be put on how to buckle up in a correct way. The above text is a part of what this investigative study is about, we have used a qualitative method for sorting out questions about the risks with free-fall lifeboats. SOLAS does not put any demands on the existence of aiding equipment to facilitate bringing injured persons in a free-fall lifeboat. The tests that have been performed with people onboard free-fall lifeboats have only taken place during favourable conditions. Considering that ships are exposed to the motion of the sea and that the boat could land on a wave the SOLAS demands should be increased. The lifeboat systems we have, is neither tested nor practised with in waves. That free-fall lifeboats is a good concept as a lifesaving equipment, there is no doubt about, but it should be developed further.</p>

<p>Syftet med vårt arbete var att ta reda på vad studenterna i avgångsklasserna vid Sjöfartshögskolan i Kalmar har för åsikt gällande användandet av skolfartyget Calmare Nyckel. Vidare hade vi för avsikt att undersöka vilken åsikt Sjöfartshögskolan i Kalmar har rörande användandet samt att ta reda på ifall det finns en skillnad mellan respektive åsikter.</p><p>Genom en analys och sammanställning av vår enkätundersökning kom vi fram till att 98 % av studenterna ansåg att de antal gånger de fått använda Calmare Nyckel, för navigation och manövrering, varit för lite. Ur våra intervjuer med anställda på skolan framkom det att de däremot är nöjda med hur de låter Calmare Nyckel komma till användning i utbildningen av sjökaptener.</p><p>Vi kunde se en tydlig skillnad i åsikter mellan skola och studenter. Skillnaden bottnade bland annat i skolans bristfälliga information om deras syfte och målsättning med Calmare Nyckel. En annan anledning till skillnaden beror på hur skolan marknadsför deras skolfartyg samt hur studenterna tolkar denna. Majoriteten av de tillfrågade studenterna i vår enkätundersökning hade en förväntan om att de skulle få använda Calmare Nyckel mer än vad de gjort under utbildningen.</p>

I noticed that the workers had the same itinerary when emptying trashcans, meanwhile trashcans needed urgently to be emptied. Traditionally, ETSU maintenance operate on daily routes to pick trash on designated time, regardless the level of the containers. This leads to overflown trashcan in busy areas or during rush hours in certain areas. This overflown trashcan result in an unclean environment for the community and an unpleasant look of our beautiful campus. The time, resources and labor invested in collecting the trash could be saved. Therefore, I decided to use the Internet of Things (IoT) to create a device that will optimize trash collection, to reduce costs and pollution. The Eco-Smart Can will contain a renewable source of energy such as the solar panel. Furthermore, it will have a compactor as well to decrease the trash volume. The system in the Eco-Smart can will give prior information of the trash level to maintenance facility so that they can empty the trash in a timely manner and preserve the environment.

I noticed that the workers had the same itinerary when emptying trashcans, meanwhile trashcans needed urgently to be emptied. Traditionally, ETSU maintenance operate on daily routes to pick trash on designated time, regardless the level of the containers. This leads to overflown trashcan in busy areas or during rush hours in certain areas. This overflown trashcan result in an unclean environment for the community and an unpleasant look of our beautiful campus. The time, resources and labor invested in collecting the trash could be saved. Therefore, I decided to use the Internet of Things (IoT) to create a device that will optimize trash collection, to reduce costs and pollution. The Eco-Smart Can will contain a renewable source of energy such as the solar panel. Furthermore, it will have a compactor as well to decrease the trash volume. The system in the Eco-Smart can will give prior information of the trash level to maintenance facility so that they can empty the trash in a timely manner and preserve the environment.

Intensive competition on the global market puts great pressure on manufacturing companies to develop and produce products that meet requirements from customers and investors. One key factor in meeting these requirements is the efficiency of the product development and the production preparation process. Design automation is a powerful tool to increase efficiency in these two processes. The benefits of automating the production preparation process are shortened led-time, improved product performance, and ultimately decreased cost. Further, automation is beneficial as it increases the ability to adapt products to new product specifications with production preparations done in few or in a single step. During the automation process, knowledge about the production preparation process is collected and stored in central systems, thus allowing full control over the design of production equipments. Three main topics are addressed in this thesis: the flexibility of design automation systems, knowledge bases containing conflicting rules, and the automation of the finite element analysis process. These three topics are discussed in connection with the production preparation process of rotary draw bending. One conclusion drawn from the research is that it is possible to apply the concept of design automation to the production preparation process at different levels of automation depending on characteristics of the implemented knowledge. In order to make design automation systems as flexible as possible, the concept of object orientation should be adapted when building the knowledge base and when building the products geometrical representations. It is possible to automate the process of setting up, running, and interpreting finite element analyses to a great extent and making the automated finite element analysis process a part of the global design automation system.

<p>På IKEA går produktionsflödet för en produktbild i dagsläget från konstruktionsritning till fotografering via tillverkning och montering. En produkt som är färdig för tillverkning definieras av sin mekaniska konstruktion och sina ytegenskaper. Ledtiden och kostnaden för bildproduktionen skulle kunna minskas betydligt om produkten kunde avbildas redan i detta stadium, utan att finnas tillverkad. För detta ändamål såg IKEA en möjlighet i att introducera ett nytt produktionsflöde där avancerad datorgrafik, grafisk teknik och bildbehandling omvandlar konstruktionsritningen till produktbild. Ambitionen är att från ritningen ta ut en 3D-modell, placera den i en omgivning, ljussätta och belägga den med material och av detta skapa en tryckbar produktbild som uppfyller företagets höga kvalitetskrav.</p><p>Syftet med examensarbetet var att ta fram förslag på ett konkret sådant flöde genom att undersöka olika programvaror som skulle kunna användas samt att identifiera problemområden och komma med lösningsförslag på dessa. Flödet delades upp i de fem problemområdena konvertering, modellering, ljussättning, material och rendering som bearbetades parallellt. Fokus har under hela projektet legat på färghantering och upplevd bildkvalitet genom att korrekt färg- och detaljåtergivning i bilderna varit pekpinne och ledsagare.</p><p>Konstruktionsritningarna som görs i SolidWorks har konverterats till 3D-modeller med programvaran PolyTrans. I 3ds max har produktmodellerna satts in i en miljö som liknar den verkliga fotostudion, belysts och belagts med material. Efter en studie av olika programvaror för rendering beslutades det att mental ray skulle användas varpå alla bilder skapats med denna. mental ray är en komplex renderare som beräknar ljussättning fysikaliskt riktigt vilket bidrar till fotorealistiska bilder.</p><p>Examensarbetet handlade till mångt och mycket om att köra olika produkter genom flödet och testa med olika inställningar i de olika stegen. Flödet utvärderades kontinuerligt genom att bilderna som kom ut bedömdes visuellt. Dessutom genomfördes några tester för att undersöka inblandade programvarors eventuella brister vad gäller färghantering och upplevd bildkvalitet. Det slutliga resultatet av examensarbetet blev ett flöde som i stor utsträckning liknar arbetsflödet vid nuvarande bildproduktion. Med minimal insats från retuschavdelningen uppfyller bilderna de krav som ställs för att de skall kunna tryckas i IKEA katalogen.</p>