No description available.

No description available.

Dye-sensitized solar cells (DSC) have attracted considerable scientific and industrial interest during the past decade as an economically feasible alternative to conventional photovoltaic devices. DSCs have the potential to be as efficient as silicon solar cells, but at a fraction of the cost of silicon solar cells. The unique advantage of DSC compared to conventional solar cells is that the light absorption, electron transport and hole transport are handled by different components which reduces the chance of recombination. In the present work, to facilitate DSC with good energy conversion efficiency, its performance have been evaluated as a function of titania layer morphology, redox couple concentration and the catalytic layer on the counter electrode. The results that are obtained in the present investigations have been organized as follows Chapter 1 gives a brief exposure to DSC technology. Special emphasize has been on the structure and individual components of the DSC. Chapter 2 describes various experimental techniques that are employed to fabricate and characterize DSCs under study. Chapter 3 presents a systematic study of the characteristics of DSC made of three different types of electrodes namely: TiO2 nanotubes (TNT) which have excellent electron transport properties, TiO2 microspheres (TMS) which possess high surface area and light scattering ability and TiO2 nano particles (TNP) possessing high surface area. The electronic, morphological, optical and surface properties of individual electrodes are studied. The highest efficiency of 8.03% is obtained for DSCs prepared with TMS electrodes. A higher value of effective diffusion coefficient (Deff) and diffusion length (Ln) of electrons as obtained by electrochemical impedance spectroscopy (EIS) analysis confirms a high charge collection efficiency in microsphere based cell. Chapter 4 gives a detailed study of DSCs fabricated with a tri-layer photo anode with TNTs as light scattering layer. The tri-layer structure has given an enhanced efficiency of 7.15% which is 16% higher than TNP based cell and 40% higher than TNT based cells. Chapter 5 deals with the investigations on the effect of concentration of redox couple on the photovoltaic properties of DSC for different ratios of [I2] to [LiI] (1:2, 1:5 and 1:10) with five viii concentrations of I2 namely 0.01 M, 0.03 M, 0.05 M, 0.08 M and 0.1M in acetonitrile. It is found that the open circuit potential (Voc) decreases with increase in the ratio of redox couple whereas short circuit current density (Jsc) and fill factor (FF) increase. The reason for the decline in Voc is the higher recombination between electrons in the conduction band of TiO2 and the I3- ions present in the electrolyte, induced by the absorptive Li+ ions. In addition using EIS it is found that the τ improves with the increase in [LiI] at a particular [I2], whereas at a fixed [I2]/ [LiI] ratio the increase in [I2] is found to reduce the τ and Deff due to the enhanced recombination. Chapter 6 describes the application of carbon based counter electrode (CE) materials for DSCs. Two counter electrode materials have been investigated namely (1) Multiwalled carbon nanotubes (MWCNT) synthesized by pyrolysis method and (2) Platinum decorated multiwalled carbon nanotubes (Pt/MWCNT) prepared by chemical reduction of platinum precursors. Using Pt/MWCNT composite electrode the DSC achieved an energy conversion efficiency of 6.5 %. From the analysis on symmetric cells, it is found that electro catalytic activity of Pt/MWCNT CE is similar to that of platinum CE, though the platinum loading is very less for the former. This is attributed to the effective utilization of catalyst owing to high surface area arising from the increased surface roughness. Chapter 7 discusses the application of titanium foil in place of glass substrate for the photo anode. The titanium foil offers fabrication of flexible DSC. The performance of DSC with TMS layers and aligned titania nanotube arrays (TNA) prepared by anodization method is studied. Compared to TMS based cell, TNA has given a better efficiency at a lower thickness. Chapter 8 presents the scheme used to seal DSCs and its stability analysis. We have employed the usual hot melt sealing for edge whereas hole sealing is carried out with tooth pick and a UV curable adhesive. The degradation in efficiency is found to be 20% for low efficiency cells whereas, for high efficiency cells it is found to be 45% after 45 days. The leakage of highly volatile acetonitrile through the edge and hole is found to be responsible for the reduction in the performance of the device. Hence a high temperature sealing method is proposed to fabricate stable cells. Chapter 9 gives summary and conclusions of the present work

Diploma thesis is focused on the study of optoelectric properties of thin layers of organic materials based on phthalocyanines, which can be used as an active layer of photovoltaic cells. Especially are studied the properties of the thin active layers of PdPc and PdPc + IL on the glass or ceramic substrates with aluminium contact, which are prepared by material printing here. On the prepared samples were first measured current-voltage characteristics in the dark and in the light and then were measured impedance spectrums in the dark. The received results will be used to improve the properties and structures of photovoltaic cells.

This thesis deals with the device physics of organic solar cells. Organic photovoltaics (OPV) is a field of applied research which has been growing rapidly in the last decade leading to a current record value of power-conversion efficiency of 10 percent. One major reason for this boom is a potentially low-cost production of solar modules on flexible (polymer) substrate. Furthermore, new application are expected by flexible or semitransparent organic solar cells. That is why several OPV startup companies were launched in the last decade. Organic solar cells consist of hydrocarbon compounds, deposited as ultrathin layers (some tens of nm) on a substrate. Absorption of light leads to molecular excited states (excitons) which are strongly bound due to the weak interactions and low dielectric constant in a molecular solid. The excitons have to be split into positive and negative charges, which are subsequently collected at different electrodes. An effective dissociation of excitons is provided by a heterojunction of two molecules with different frontier orbital energies, such that the electron is transfered to the (electron) acceptor and the positive charge (hole) remains on the donor molecule. This junction can be realized by two distinct layers forming a planar heterojunction or by an intermixed film of donor and acceptor, resulting in a bulk heterojunction. Electrodes are attached to the absorber to collect the charges by providing an ohmic contact in the optimum case. This work focuses on the electrical processes in organic solar cells developing and employing a one-dimensional drift-diffusion model. The electrical model developed here is combined with an optical model and covers the diffusion of excitons, their separation, and the subsequent transport of charges. In contrast to inorganics, charge-carrier mobilities are low in the investigated materials and charge transport is strongly affected by energy barriers at the electrodes. The current-voltage characteristics (J-V curve) of a solar cell reflect the electrical processes in the device. Therefore, the J-V curve is selected as means of comparison between systematic series of simulation and experimental data. This mainly qualitative approach allows for an identification of dominating processes and provides microscopic explanations. One crucial issue, as already mentioned, is the contact between absorber layer and electrode. Energy barriers lead to a reduction of the power-conversion efficiency due to a decrease in the open-circuit voltage or the fill factor by S-shaped J-V curve (S-kink), which are often observed for organic solar cells. It is shown by a systematic study that the introduction of deliberate barriers for charge-carrier extraction and injection can cause such S-kinks. It is explained by simulated electrical-field profiles why also injection barriers lead to a reduction of the probability for charge-carrier extraction. A pile-up of charge carriers at an extraction barrier is confirmed by measurements of transient photocurrents. In flat heterojunction solar cells an additional reason for S-kinks is found in an imbalance of electron and hole mobilities. Due to the variety of reasons for S-kinks, methods and criteria for a distinction are proposed. These include J-V measurements at different temperatures and of samples with varied layer thicknesses. Most of the studies of this this work are based on experimental data of solar cells comprisiing the donor dye zinc phthalocyanine and the acceptor fullerene C60. It is observed that the open-circuit voltage of these devices depends on the mixing ratio of ZnPc:C60. A comparison of experimental and simulation data indicates that the reason is a changed donor-acceptor energy gap caused by a shift of the ionization potential of ZnPc. A spatial gradient in the mixing ratio of a bulk heterojunction is also investigated as a donor(acceptor)-rich mixture at the hole(electron)-collecting contact is supposed to assist charge extraction. This effect is not observed, but a reduction of charge-carrier losses at the “wrong” electrode which is seen at an increase in the open-circuit voltage. The most important intrinsic loss mechanism of a solar cell is bulk recombination which is treated at the example of ZnPc:C60 devices in the last part of this work. An examination of the dependence of the open-circuit voltage on illumination intensity shows that the dominating recombination mechanism shifts from trap-assisted to direct recombination for higher intensities. A variation of the absorption profile within the blend layer shows that the probability of charge-carrier extraction depends on the locus of charge-carrier generation. This results in a fill factor dependent on the absorption profile. The reason is an imbalance in charge-carrier mobilities which can be influenced by the mixing ratio. The work is completed by a simulation study of the influence of charge-carrier mobilities and different recombination processes on the J-V curve and an identification of a photoshunt dominating the experimental linear photocurrent-voltage characteristics in reverse bias.:Abstract - Kurzfassung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v 1 Introduction 1.1 Energy supply and climate change . . . . . . . . . . . . . . . . . . . . . . 1 1.2 Development of (organic) photovoltaics . . . . . . . . . . . . . . . . . . 3 1.3 Structure and scope of this thesis . . . . . . . . . . . . . . . . . . . . . . 6 I Basics 2 Photovoltaic Energy Conversion 2.1 Fundamentals of solar thermal energy conversion . . . . . . . . . . .11 2.1.1 The solar spectrum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.1.2 Black-body irradiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 2.1.3 Maximum power-conversion efficiency . . . . . . . . . . . . . . . . . 15 2.2 Basics of semiconductor physics . . . . . . . . . . . . . . . . . . . . . . 16 2.2.1 Band structure, electrons and holes . . . . . . . . . . . . . . . . . . 16 2.2.2 Quasi-Fermi levels and electrochemical potentials . . . . . . . . . .22 2.3 Transformation of thermal radiation into chemical energy . . . . . 28 2.4 From chemical energy to electrical energy . . . . . . . . . . . .. . . . . 29 2.5 Possible solar-cell realizations . . . . . . . . . . . . . . . . . . . . . . . . 33 2.5.1 The p-n junction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 2.5.2 Heterojunction and dye solar cells . . . . . . . . . . . . . . . . . . . . 36 2.5.3 The p-i-n concept with wide-gap transport layers . . . . . . . . . 37 2.6 Maximum efficiency – Shockley-Queisser limit . . . . . . . . . . . . . .38 2.7 Novel concepts and classification of solar cells . . . . . . . . . . . . . 41 3 Organic Solar Cells 3.1 Energetics of organic molecules . . . . . . . . . . . . . . . . . . . . . . . 43 3.1.1 From atoms to molecules . . . . . . . . . . . . . . . . . . . . . . . . . . 43 3.1.2 From single molecules to a molecular solid . . . . . . . . . . . . . . 50 3.2 Energy and charge transport in organic semiconductors . . . . . . 52 3.2.1 Exciton transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 3.2.2 Charge transport - Gaussian disorder model . . . . . . . . . . . . .53 3.3 Working principle of donor-acceptor heterojunction solar cells . .57 3.3.1 Particle losses, quantum efficiency, and photocurrent . . . . . . .57 3.3.2 Energy losses, potential energy, and photovoltage . . . . . . . . 62 3.3.3 Maximum power-conversion efficiency . . . . . . . . . . . . . . . . . 66 3.3.4 Understanding the J-V curve in the MIM picture . . . . . . . . . . .68 3.3.5 Introduction to analytical models describing the photocurrent 70 3.4 Metal-organic interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 3.4.1 Conventional metal-semiconductor interfaces: Barriers and Schottky contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 3.4.2 Metal-organic interfaces: Disorder and ICT . . . . . . . . . . . . . . 79 3.5 Experimental realization of small-molecule solar cells . . . . . . . . 80 3.5.1 Stacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 3.5.2 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 3.5.3 Fabrication details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 3.6 Basic characterization methods . . . . . . . . . . . . . . . . . . . . . . . 92 3.6.1 Current-voltage characteristics . . . . . . . . . . . . . . . . . . . . . . 92 3.6.2 Spectrally resolved measurements . . . . . . . . . . . . . . . . . . . 93 3.6.3 Transient measurements . . . . . . . . . . . . . . . . . . . . . . . . . . 95 4 Modeling 4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 4.2 The drift-diffusion model in general . . . . . . . . . . . . . . . . . . . . 99 4.2.1 Derivation and conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 99 4.2.2 The Einstein Relation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 4.2.3 Poisson’s equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 4.2.4 Differential equation system . . . . . . . . . . . . . . . . . . . . . . . .105 4.3 Implementation of the algorithm . . . . . . . . . . . . . . . . . . . . . . 106 4.3.1 Basics of the algorithm and discretization . . . . . . . . . . . . . . 107 4.3.2 Calculation of the electric field . . . . . . . . . . . . . . . . . . . . . . 108 4.3.3 Calculation of rates of change . . . . . . . . . . . . . . . . . . . . . . 109 4.3.4 Calculation of the time step . . . . . . . . . . . . . . . . . . . . . . . . 111 4.3.5 Detection of steady state and transient currents . . . . . . . . . 111 4.4 Implemented models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 4.4.1 Charge carrier mobility . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 4.4.2 Recombination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 4.4.3 Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 4.4.4 Gaussian density of states . . . . . . . . . . . . . . . . . . . . . . . . 120 4.5 Contacts as boundary conditions . . . . . . . . . . . . . . . . . . . . . 121 4.6 Organic-organic interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . 124 4.6.1 Charge transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 4.6.2 Generation and recombination . . . . . . . . . . . . . . . . . . . . . . 127 4.7 The simulation tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 4.8 Verification with analytical solutions . . . . . . . . . . . . . . . . . . . 129 4.8.1 Single-carrier devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 4.8.2 The p-n junction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 4.9 Experimental determination of material properties . . . . . . . . . 136 4.10 Summary and main input parameters . . . . . . . . . . . . . . . . . 140 II Results and Discussion 5 Simulation Study on Single-Layer Bulk-Heterojunction Solar Cells 5.1 Investigated device structure and definitions . . . . . . . . . . . . . 144 5.2 On the optimum mobility, contact properties, and the open-circuit voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 5.2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146 5.2.2 Investigated mobility and recombination models . . . . . . . . . .147 5.2.3 Recombination only in the BHJ (selective contacts) . . . . . . . . 149 5.2.4 Recombination (also) at electrodes (non-selective contacts) . .155 5.2.5 Injection barriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 5.2.6 Effect of energy-level bending on the open-circuit voltage . . . 161 5.3 Photocurrent and characteristic points in simulated J-V curves . .163 5.3.1 Negligible bulk recombination . . . . . . . . . . . . . . . . . . . . . . . .164 5.3.2 Bulk-recombination-limited photocurrent . . . . . . . . . . . . . . . 167 5.4 The effect of disorder on the open-circuit voltage . . . . . . . . . . .169 5.5 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172 6 Influence of Injection and Extraction Barriers on Open-Circuit Voltage and J-V Curve Shape studied at a Variation of Hole Transport Layer and Donor Materials 6.1 Methodological approach . . . . . . . . . . . . . . . . . . . . . . . . . . . .174 6.2 Current-voltage data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 6.2.1 Fingerprints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 6.2.2 Current-voltage characteristics under illumination . . . . . . . . . 181 6.3 Detailed microscopic explanations . . . . . . . . . . . . . . . . . . . . . .181 6.3.1 Injection barriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184 6.3.2 Extraction barriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187 6.3.3 Comparison between flat and bulk heterojunction . . . . . . . . . 188 6.4 Current-voltage curves in a logarithmic plot . . . . . . . . . . . . . . .188 6.5 Detailed analysis of the material combination MeO-TPD and BPAPF as donor and hole transport layer . . . . . . . . . . . . . . . . . . . . . . . . . . 190 6.5.1 The interfaces BPAPF/MeO-TPD and MeO-TPD/BPAPF measured by photoelectron spectroscopy . . . . . . . . . . . . . . . . . . . . . . . . . . 190 6.5.2 Dependence of the J-V curve shape on layer thicknesses . . . . 195 6.5.3 Dependence of the S-kink on temperature . . . . . . . . . . . . . . 198 6.5.4 Transient measurements . . . . . . . . . . . . . . . . . . . . . . . . . . 200 6.6 Summary and final remarks . . . . . . . . . . . . . . . . . . . . . . . . . . 207 7 Imbalanced Mobilities causing S-shaped J-V Curves in Planar Heterojunction Solar Cells 7.1 Imbalanced mobilities in simulation . . . . . . . . . . . . . . . . . . . . . 209 7.2 Experimental verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 7.2.1 Current-voltage characteristics . . . . . . . . . . . . . . . . . . . . . . 216 7.2.2 Transient photocurrents . . . . . . . . . . . . . . . . . . . . . . . . . . 219 7.3 Field-dependent exciton dissociation as an additional source of S-kinks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 7.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 8 Open-Circuit Voltage and J-V Curve Shape of ZnPc:C60 Solar Cells with Varied Mixing Ratio and Hole Transport Layer 8.1 Experimental approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 8.2 The open-circuit voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 8.3 The role of the hole transport layer and of doping . . . . . . . . . .228 8.4 Explaining the open-circuit voltage as a function of mixing ratio 230 8.5 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 9 Effect of Concentration Gradients in ZnPc:C60 Bulk Heterojunction Solar Cells 9.1 Investigated devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 9.2 Current-voltage results . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 9.2.1 Fill factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 9.2.2 Short-circuit current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242 9.2.3 Open-circuit voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242 9.3 Voltage dependent external quantum efficiency data . . . . . . . . 245 9.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .247 10 Role of the Generation Profile and Recombination in ZnPc:C60 Solar Cells 10.1 Idea and solar-cell design . . . . . . . . . . . . . . . . . . . . . . . . . . 249 10.1.1 Absorption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 10.1.2 Simulated generation profiles . . . . . . . . . . . . . . . . . . . . . . 253 10.2 Correlation of fill factor with generation profile and imbalance in mobilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 10.2.1 Current-voltage data . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 10.2.2 Monochromatic J-V curves . . . . . . . . . . . . . . . . . . . . . . . . 258 10.2.3 Voltage dependent external quantum efficiency . . . . . . . . . 259 10.3 Recombination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 10.3.1 Exponential region of dark J-V curves . . . . . . . . . . . . . . . . 261 10.3.2 J-V data dependent on illumination intensity . . . . . . . . . . . 265 10.3.3 Lifetime of charge carriers . . . . . . . . . . . . . . . . . . . . . . . . 271 10.4 Comparison with simulations . . . . . . . . . . . . . . . . . . . . . . . . 273 10.5 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 11 Linear Saturation Behavior 11.1 Definition of the photoshunt . . . . . . . . . . . . . . . . . . . . . . . . 279 11.2 Quasi-linear photocurrent in simulation . . . . . . . . . . . . . . . . 280 11.3 Experimental approach and results . . . . . . . . . . . . . . . . . . . 281 11.3.1 Identification of the main source of the photoshunt . . . . . . 283 11.3.2 Investigation of the thickness dependence of the saturation 285 11.3.3 Photoshunt in flat heterojunction ZnPc/C60 solar cells . . . . 289 11.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 III Summary and Outlook 12 Main Results 12.1 Interpretation of current-voltage curves . . . . . . . . . . . . . . . . 295 12.2 Stack design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 12.3 Main conclusions on the applicability of the developed drift-diffusion simulation to organic solar cells . . . . . . . . . . . . . . . . . . . . . . . . . . 302 13 Further Analyses and Possible Extensions of the Simulation 13.1 Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 13.2 Reverse tunneling currents and tandem cells . . . . . . . . . . . . . 307 13.2.1 Reverse current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308 13.2.2 J-V curves of tandem cells . . . . . . . . . . . . . . . . . . . . . . . . 309 13.3 Further points to examine . . . . . . . . . . . . . . . . . . . . . . . . . . 311 Appendix A Lists A.1 List of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315 A.2 List of abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 A.3 List of constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 B Simulation data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 C Experimental data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 Bibliography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 Acknowledgments - Danksagung 361 / Diese Dissertation beschäftigt sich mit der Physik organischer Solarzellen. Die organische Photovoltaik ist ein Forschungsgebiet, dem in den letzten zehn Jahren enorme Aufmerksamkeit zu Teil wurde. Der Grund liegt darin, dass diese neuartigen Solarzellen, deren aktueller Rekordwirkungsgrad bei 10 Prozent liegt, ein Potential für eine kostengünstige Produktion auf flexiblem (Polymer)substrat aufweisen und aufgrund ihrer Vielfältigkeit neue Anwendungsbereiche für die Photovoltaik erschließen. Organische Solarzellen bestehen aus ultradünnen (einige 10 nm) Schichten aus Kohlenwasserstoffverbindungen. Damit der photovoltaische Effekt genutzt werden kann, müssen die durch Licht angeregten Molekülzustände zu freien Ladungsträgern führen, wobei positive und negative Ladung an unterschiedlichen Kontakten extrahiert werden. Für eine effektive Trennung dieser stark gebundenden lokalisierten angeregten Zustände (Exzitonen) ist eine Grenzfläche zwischen Molekülen mit unterschiedlichen Energieniveaus der Grenzorbitale erforderlich, sodass ein Elektron auf einem Akzeptor- und eine positive Ladung auf einem Donatormolekül entstehen. Diese Grenzschicht kann als planarer Heteroübergang durch zwei getrennte Schichten oder als Volumen-Heteroübergang in einer Mischschicht realisiert werden. Die Absorberschichten werden durch Elektroden kontaktiert, wobei es für effiziente Solarzellen erforderlich ist, dass diese einen ohmschen Kontakt ausbilden, da ansonsten Verluste zu erwarten sind. Diese Arbeit behandelt im Besonderen die elektrischen Prozesse einer organischen Solarzelle. Dafür wird ein eindimensionales Drift-Diffusionsmodell entwickelt, das den Transport von Exzitonen, deren Trennung an einer Grenzfläche und die Ladungsträgerdynamik beschreibt. Abgesehen von den Exzitonen gilt als weitere Besonderheit einer organischen Solarzelle, dass sie aus amorphen, intrinsischen und sehr schlecht leitfähigen Absorberschichten besteht. Elektrische Effekte sind an der Strom-Spannungskennlinie (I-U ) sichtbar, die in dieser Arbeit als Hauptvergleichspunkt zwischen experimentellen Solarzellendaten und den Simulationsergebnissen dient. Durch einen weitgehend qualitativen Vergleich können dominierende Prozesse bestimmt und mikroskopische Erklärungen gefunden werden. Ein wichtiger Punkt ist der schon erwähnte Kontakt zwischen Absorberschicht und Elektrode. Dort auftretende Energiebarrieren führen zu einem Einbruch im Solarzellenwirkungsgrad, der sich durch eine Verringerung der Leerlaufspanung und/oder S-förmigen Kennlinien (S-Knick) bemerkbar macht. Anhand einer systematischen Studie der Grenzfläche Lochleiter/Donator wird gezeigt, dass Energiebarrieren sowohl für die Ladungsträgerextraktion als auch für die -injektion zu S-Knicken führen können. Insbesondere die Tatsache, dass Injektionsbarrieren sich auch negativ auf den Photostrom auswirken, wird anhand von simulierten Ladungsträger- und elektrischen Feldprofilen erklärt. Das Aufstauen von Ladungsträgern an Extraktionsbarrieren wird durch Messungen transienter Photoströme bestätigt. Da S-Knicke in organischen Solarzellen im Allgemeinen häufig beobachtet werden, werden weitere Methoden vorgeschlagen, die die Identifikation der Ursachen ermöglichen. Dazu zählen I-U Messungen in Abhängigkeit von Temperatur und Schichtdicken. Als eine weitere Ursache von S-Knicken werden unausgeglichene Ladungsträgerbeweglichkeiten in einer Solarzelle mit flachem Übergang identifiziert und von den Barrierefällen unterschieden. Weiterer Forschungsgegenstand dieser Arbeit sind Mischschichtsolarzellen aus dem Donator-Farbstoff Zink-Phthalozyanin ZnPc und dem Akzeptor Fulleren C60. Dort wird beobachtet, dass die Leerlaufspannung vom Mischverhältnis abhängt. Ein Vergleich von Experiment und Simulation zeigt, dass sich das Ionisationspotenzial von ZnPc und dadurch die effektive Energielücke des Mischsystems ändern. Zusätzlich zu homogenen Mischschichten werden Solarzellen untersucht, die einen Gradienten im Mischungsverhältnis aufweisen. Die Vermutung liegt nahe, dass ein hoher Donatorgehalt am Löcherkontakt und ein hoher Akzeptorgehalt nahe des Elektronenkontakts die Ladungsträgerextraktion begünstigen. Dieser Effekt ist in dem hier untersuchten System allerdings vergleichsweise irrelevant gegenüber der Tatsache, dass der Gradient das Abfließen bzw. die Rekombination von Ladungsträgern am “falschen” Kontakt reduziert und somit die Leerlaufspannung erhöht. Der wichtigste intrinsische Verlustmechanismus einer Solarzelle ist die Rekombination von Ladungsträgern. Diese wird im letzten Teil der Arbeit anhand der ZnPc:C60 Solarzelle behandelt. Messungen der Leerlaufspannung in Abhängigkeit von der Beleuchtungsintensität zeigen, dass sich der dominierende Rekombinationsprozess mit zunehmender Intensität von Störstellenrekombination zu direkter Rekombination von freien Ladungsträgern verschiebt. Eine gezielte Variation des Absorptionsprofils in der Absorberschicht zeigt, dass die Ladungsträgerextraktionswahrscheinlickeit vom Ort der Ladungsträgergeneration abhängt. Dieser Effekt wird hervorgerufen durch unausgeglichene Elektronen- und Löcherbeweglichkeiten und äußert sich im Füllfaktor. Weitere Simulationsergebnisse bezüglich des Einflusses von Ladungsträgerbeweglichkeiten und verschiedener Rekombinationsmechanismen auf die I-U Kennlinie und die experimentelle Identifikation eines Photoshunts, der den Photostrom in Rückwärtsrichtung unter Beleuchtung dominiert, runden die Arbeit ab.:Abstract - Kurzfassung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v 1 Introduction 1.1 Energy supply and climate change . . . . . . . . . . . . . . . . . . . . . . 1 1.2 Development of (organic) photovoltaics . . . . . . . . . . . . . . . . . . 3 1.3 Structure and scope of this thesis . . . . . . . . . . . . . . . . . . . . . . 6 I Basics 2 Photovoltaic Energy Conversion 2.1 Fundamentals of solar thermal energy conversion . . . . . . . . . . .11 2.1.1 The solar spectrum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.1.2 Black-body irradiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 2.1.3 Maximum power-conversion efficiency . . . . . . . . . . . . . . . . . 15 2.2 Basics of semiconductor physics . . . . . . . . . . . . . . . . . . . . . . 16 2.2.1 Band structure, electrons and holes . . . . . . . . . . . . . . . . . . 16 2.2.2 Quasi-Fermi levels and electrochemical potentials . . . . . . . . . .22 2.3 Transformation of thermal radiation into chemical energy . . . . . 28 2.4 From chemical energy to electrical energy . . . . . . . . . . . .. . . . . 29 2.5 Possible solar-cell realizations . . . . . . . . . . . . . . . . . . . . . . . . 33 2.5.1 The p-n junction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 2.5.2 Heterojunction and dye solar cells . . . . . . . . . . . . . . . . . . . . 36 2.5.3 The p-i-n concept with wide-gap transport layers . . . . . . . . . 37 2.6 Maximum efficiency – Shockley-Queisser limit . . . . . . . . . . . . . .38 2.7 Novel concepts and classification of solar cells . . . . . . . . . . . . . 41 3 Organic Solar Cells 3.1 Energetics of organic molecules . . . . . . . . . . . . . . . . . . . . . . . 43 3.1.1 From atoms to molecules . . . . . . . . . . . . . . . . . . . . . . . . . . 43 3.1.2 From single molecules to a molecular solid . . . . . . . . . . . . . . 50 3.2 Energy and charge transport in organic semiconductors . . . . . . 52 3.2.1 Exciton transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 3.2.2 Charge transport - Gaussian disorder model . . . . . . . . . . . . .53 3.3 Working principle of donor-acceptor heterojunction solar cells . .57 3.3.1 Particle losses, quantum efficiency, and photocurrent . . . . . . .57 3.3.2 Energy losses, potential energy, and photovoltage . . . . . . . . 62 3.3.3 Maximum power-conversion efficiency . . . . . . . . . . . . . . . . . 66 3.3.4 Understanding the J-V curve in the MIM picture . . . . . . . . . . .68 3.3.5 Introduction to analytical models describing the photocurrent 70 3.4 Metal-organic interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 3.4.1 Conventional metal-semiconductor interfaces: Barriers and Schottky contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 3.4.2 Metal-organic interfaces: Disorder and ICT . . . . . . . . . . . . . . 79 3.5 Experimental realization of small-molecule solar cells . . . . . . . . 80 3.5.1 Stacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 3.5.2 Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 3.5.3 Fabrication details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 3.6 Basic characterization methods . . . . . . . . . . . . . . . . . . . . . . . 92 3.6.1 Current-voltage characteristics . . . . . . . . . . . . . . . . . . . . . . 92 3.6.2 Spectrally resolved measurements . . . . . . . . . . . . . . . . . . . 93 3.6.3 Transient measurements . . . . . . . . . . . . . . . . . . . . . . . . . . 95 4 Modeling 4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 4.2 The drift-diffusion model in general . . . . . . . . . . . . . . . . . . . . 99 4.2.1 Derivation and conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 99 4.2.2 The Einstein Relation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 4.2.3 Poisson’s equation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 4.2.4 Differential equation system . . . . . . . . . . . . . . . . . . . . . . . .105 4.3 Implementation of the algorithm . . . . . . . . . . . . . . . . . . . . . . 106 4.3.1 Basics of the algorithm and discretization . . . . . . . . . . . . . . 107 4.3.2 Calculation of the electric field . . . . . . . . . . . . . . . . . . . . . . 108 4.3.3 Calculation of rates of change . . . . . . . . . . . . . . . . . . . . . . 109 4.3.4 Calculation of the time step . . . . . . . . . . . . . . . . . . . . . . . . 111 4.3.5 Detection of steady state and transient currents . . . . . . . . . 111 4.4 Implemented models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 4.4.1 Charge carrier mobility . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 4.4.2 Recombination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 4.4.3 Traps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 4.4.4 Gaussian density of states . . . . . . . . . . . . . . . . . . . . . . . . 120 4.5 Contacts as boundary conditions . . . . . . . . . . . . . . . . . . . . . 121 4.6 Organic-organic interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . 124 4.6.1 Charge transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 4.6.2 Generation and recombination . . . . . . . . . . . . . . . . . . . . . . 127 4.7 The simulation tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 4.8 Verification with analytical solutions . . . . . . . . . . . . . . . . . . . 129 4.8.1 Single-carrier devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 4.8.2 The p-n junction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 4.9 Experimental determination of material properties . . . . . . . . . 136 4.10 Summary and main input parameters . . . . . . . . . . . . . . . . . 140 II Results and Discussion 5 Simulation Study on Single-Layer Bulk-Heterojunction Solar Cells 5.1 Investigated device structure and definitions . . . . . . . . . . . . . 144 5.2 On the optimum mobility, contact properties, and the open-circuit voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146 5.2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146 5.2.2 Investigated mobility and recombination models . . . . . . . . . .147 5.2.3 Recombination only in the BHJ (selective contacts) . . . . . . . . 149 5.2.4 Recombination (also) at electrodes (non-selective contacts) . .155 5.2.5 Injection barriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 5.2.6 Effect of energy-level bending on the open-circuit voltage . . . 161 5.3 Photocurrent and characteristic points in simulated J-V curves . .163 5.3.1 Negligible bulk recombination . . . . . . . . . . . . . . . . . . . . . . . .164 5.3.2 Bulk-recombination-limited photocurrent . . . . . . . . . . . . . . . 167 5.4 The effect of disorder on the open-circuit voltage . . . . . . . . . . .169 5.5 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .172 6 Influence of Injection and Extraction Barriers on Open-Circuit Voltage and J-V Curve Shape studied at a Variation of Hole Transport Layer and Donor Materials 6.1 Methodological approach . . . . . . . . . . . . . . . . . . . . . . . . . . . .174 6.2 Current-voltage data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 6.2.1 Fingerprints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 6.2.2 Current-voltage characteristics under illumination . . . . . . . . . 181 6.3 Detailed microscopic explanations . . . . . . . . . . . . . . . . . . . . . .181 6.3.1 Injection barriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184 6.3.2 Extraction barriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .187 6.3.3 Comparison between flat and bulk heterojunction . . . . . . . . . 188 6.4 Current-voltage curves in a logarithmic plot . . . . . . . . . . . . . . .188 6.5 Detailed analysis of the material combination MeO-TPD and BPAPF as donor and hole transport layer . . . . . . . . . . . . . . . . . . . . . . . . . . 190 6.5.1 The interfaces BPAPF/MeO-TPD and MeO-TPD/BPAPF measured by photoelectron spectroscopy . . . . . . . . . . . . . . . . . . . . . . . . . . 190 6.5.2 Dependence of the J-V curve shape on layer thicknesses . . . . 195 6.5.3 Dependence of the S-kink on temperature . . . . . . . . . . . . . . 198 6.5.4 Transient measurements . . . . . . . . . . . . . . . . . . . . . . . . . . 200 6.6 Summary and final remarks . . . . . . . . . . . . . . . . . . . . . . . . . . 207 7 Imbalanced Mobilities causing S-shaped J-V Curves in Planar Heterojunction Solar Cells 7.1 Imbalanced mobilities in simulation . . . . . . . . . . . . . . . . . . . . . 209 7.2 Experimental verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 7.2.1 Current-voltage characteristics . . . . . . . . . . . . . . . . . . . . . . 216 7.2.2 Transient photocurrents . . . . . . . . . . . . . . . . . . . . . . . . . . 219 7.3 Field-dependent exciton dissociation as an additional source of S-kinks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .221 7.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222 8 Open-Circuit Voltage and J-V Curve Shape of ZnPc:C60 Solar Cells with Varied Mixing Ratio and Hole Transport Layer 8.1 Experimental approach . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 8.2 The open-circuit voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . .225 8.3 The role of the hole transport layer and of doping . . . . . . . . . .228 8.4 Explaining the open-circuit voltage as a function of mixing ratio 230 8.5 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 9 Effect of Concentration Gradients in ZnPc:C60 Bulk Heterojunction Solar Cells 9.1 Investigated devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 9.2 Current-voltage results . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 9.2.1 Fill factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 9.2.2 Short-circuit current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242 9.2.3 Open-circuit voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242 9.3 Voltage dependent external quantum efficiency data . . . . . . . . 245 9.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .247 10 Role of the Generation Profile and Recombination in ZnPc:C60 Solar Cells 10.1 Idea and solar-cell design . . . . . . . . . . . . . . . . . . . . . . . . . . 249 10.1.1 Absorption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251 10.1.2 Simulated generation profiles . . . . . . . . . . . . . . . . . . . . . . 253 10.2 Correlation of fill factor with generation profile and imbalance in mobilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 10.2.1 Current-voltage data . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 10.2.2 Monochromatic J-V curves . . . . . . . . . . . . . . . . . . . . . . . . 258 10.2.3 Voltage dependent external quantum efficiency . . . . . . . . . 259 10.3 Recombination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 10.3.1 Exponential region of dark J-V curves . . . . . . . . . . . . . . . . 261 10.3.2 J-V data dependent on illumination intensity . . . . . . . . . . . 265 10.3.3 Lifetime of charge carriers . . . . . . . . . . . . . . . . . . . . . . . . 271 10.4 Comparison with simulations . . . . . . . . . . . . . . . . . . . . . . . . 273 10.5 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 11 Linear Saturation Behavior 11.1 Definition of the photoshunt . . . . . . . . . . . . . . . . . . . . . . . . 279 11.2 Quasi-linear photocurrent in simulation . . . . . . . . . . . . . . . . 280 11.3 Experimental approach and results . . . . . . . . . . . . . . . . . . . 281 11.3.1 Identification of the main source of the photoshunt . . . . . . 283 11.3.2 Investigation of the thickness dependence of the saturation 285 11.3.3 Photoshunt in flat heterojunction ZnPc/C60 solar cells . . . . 289 11.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 292 III Summary and Outlook 12 Main Results 12.1 Interpretation of current-voltage curves . . . . . . . . . . . . . . . . 295 12.2 Stack design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 12.3 Main conclusions on the applicability of the developed drift-diffusion simulation to organic solar cells . . . . . . . . . . . . . . . . . . . . . . . . . . 302 13 Further Analyses and Possible Extensions of the Simulation 13.1 Frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 13.2 Reverse tunneling currents and tandem cells . . . . . . . . . . . . . 307 13.2.1 Reverse current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308 13.2.2 J-V curves of tandem cells . . . . . . . . . . . . . . . . . . . . . . . . 309 13.3 Further points to examine . . . . . . . . . . . . . . . . . . . . . . . . . . 311 Appendix A Lists A.1 List of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 315 A.2 List of abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 318 A.3 List of constants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319 B Simulation data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 C Experimental data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333 Bibliography . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 Acknowledgments - Danksagung 361

<p>  </p> <p>Organic-inorganic halide perovskites are at the brink of commercialization as the next generation of light-absorbing materials for solar energy harvesting devices. Perovskites have large absorption coefficients, long charge-carrier lifetimes and diffusion lengths, and a tunable absorption spectrum. Furthermore, these materials can be low-temperature solution-processed, which transfers to low-cost manufacturing and cost-competitive products. The remarkable material properties of perovskites enable a broad product-market fit, encompassing traditional and new applications for solar technology. Perovskites can be deposited on flexible substrates for flexible solar cells, applied in thermochromic windows for power generation and building cooling, or tuned for tandem solar cell application to include in high-performance solar panels. However, perovskites are intrinsically unstable, which has so far prevented their commercialization. Despite large research efforts, including over two thousand publications per year, perovskite solar cells degrade in under one year of operation. In a saturated research field, new ideas are needed to inspire alternative approaches to solve the perovskite stability problem. In this dissertation, we detail research efforts surrounding the concept of a self-healing perovskite solar cell.</p> <p>     A self-healing perovskite solar cell can be classified with two distinctions: mechanically healing and molecularly healing. First, mechanically self-healing involves the material’s ability to recover its intrinsic properties after mechanical damage such as tares, lacerations, or cracking. This type of healing was unique to the organic polymer community and ultra-rare in semiconducting materials. By combining a self-healing polymer with perovskite material, we developed a self-healing semiconducting perovskite composite material which can heal using synergistic grain growth and solid-state diffusion processes at slightly elevated temperatures. The material is demonstrated in flexible solar cells with improved bending durability and a power conversion efficiency reaching 10%. The addition of fluidic polymer enables macroscopic perovskite material movement, which is otherwise brittle and rigid. The results inspire the use of polymer scaffolds for mechanically self-healing solar cells.</p> <p>     The second type of healing, molecular healing, involves healing defects within the rigid crystal domains resulting from ion migration. The same phenomenon which leads to device degradation, also assists the recovery of the device performance after resting the device in the dark. During device operation, perovskite ions diffuse in the perovskite lattice and accumulate at the device interfaces where they undergo chemical reactions or leave the perovskite layer, ultimately consuming the perovskite precursors. The photovoltaic performance can be recovered if irreversible degradation is limited. Ideally, degradation and recovery can match day and night cycling to dramatically extend the lifetime of perovskite solar cells. In this dissertation, we introduce the application of chalcogenide chemistry in the fabrication of perovskite solar cells to control the thin film crystallization process, ultimately to reduce defects in the perovskite bulk and introduce surface functionality which extends the device stability. This new strategy will help improve molecularly self-healing perovskite solar cell by reducing irreversible degradation. Lastly, we present a few other new ideas to inspire future research in perovskite solar cells and assist in the commercialization of the next generation of photovoltaics.</p>

Indiana University-Purdue University Indianapolis (IUPUI) / Fabrication and analysis of Copper Indium Gallium di-Selenide (CIGS) nanoparticles-based thin film solar cells are presented and discussed. This work explores non-traditional fabrication processes, such as spray-coating for the low-cost and highly-scalable production of CIGS-based solar cells. CIGS nanoparticles were synthesized and analyzed, thin CIGS films were spray-deposited using nanoparticle inks, and resulting films were used in low-cost fabrication of a set of CIGS solar cell devices. This synthesis method utilizes a chemical colloidal process resulting in the formation of nanoparticles with tunable band gap and size. Based on theoretical and experimental studies, 100 nm nanoparticles with an associated band gap of 1.33 eV were selected to achieve the desired film characteristics and device performances. Scanning electron microcopy (SEM) and size measurement instruments (Zetasizer) were used to study the size and shape of the nanoparticles. Electron dispersive spectroscopy (EDS) results confirmed the presence of the four elements, Copper (Cu), Indium (In), Gallium (Ga), and Selenium (Se) in the synthesized nanoparticles, while X-ray diffraction (XRD) results confirmed the tetragonal chalcopyrite crystal structure. The ultraviolet-visible-near infra-red (UV-Vis-NIR) spectrophotometry results of the nanoparticles depicted light absorbance characteristics with good overlap against the solar irradiance spectrum. The depositions of the nanoparticles were performed using spray-coating techniques. Nanoparticle ink dispersed in ethanol was sprayed using a simple airbrush tool. The thicknesses of the deposited films were controlled through variations in the deposition steps, substrate to spray-nozzle distance, size of the nozzle, and air pressure. Surface features and topology of the spray-deposited films were analyzed using atomic force microscopy (AFM). The deposited films were observed to be relatively uniform with a minimum thickness of 400 nm. Post-annealing of the films at various temperatures was studied for the photoelectric performance of the deposited films. Current density and voltage (J/V) characteristics were measured under light illumination after annealing at different temperatures. It was observed that the highest photoelectric effect resulted in annealing temperatures of 150-250 degree centigrade under air atmosphere. The developed CIGS films were implemented in solar cell devices that included Cadmium Sulfide (CdS) and Zinc Oxide (ZnO) layers. The CdS film served as the n-type layer to form a pn junction with the p-type CIGS layer. In a typical device, a 300 nm CdS layer was deposited through chemical bath deposition on a 1 $mu$m thick CIGS film. A thin layer of intrinsic ZnO was spray coated on the CdS film to prevent shorting with the top conductor layer, 1.5 μm spray-deposited aluminum doped ZnO layer. A set of fabricated devices were tested using a Keithley semiconductor characterization instrument and micromanipulator probe station. The highest measured device efficiency was 1.49%. The considered solar cell devices were simulated in ADEPT 2.0 solar cell simulator based on the given fabrication and experimental parameters. The simulation module developed was successfully calibrated with the experimental results. This module can be used for future development of the given work.

Dye-sensitized Solar Cells (DSSC), also known as Grätzel cells, have been identified as a cost-effective, easy-to-manufacture alternative to conventional solar cells. While mimicking natural photosynthesis, they are currently the most efficient third-generation solar technology available. Among others, their cost is dominated by the synthetic dye which consists of efficient Ruthenium based complexes due to their high and wide spectral absorbance. However, the severe toxicity, sophisticated preparation techniques as well as the elevated total cost of the sensitizing dye is of concern. Consequently, the current global trend in the field focuses on the exploitation of alternative organic dyes such as natural dyes which have been studied intensively. The main attractive features of natural dyes are their availability, environmental friendly, less toxicity, less polluting and low in cost. This contribution reports on the possibility of using sepia melanin dye for such DSSC application in replacement of standard costly ruthenium dyes. The sepia melanin polymer has interesting properties such as a considerable spectral absorbance width due to the high degree of conjugation of the molecule. This polymer is capable of absorbing light quantum, both at low and high energies ranging from the infrared to the UV region. The comprehensive literature survey on Grätzel solar cells, its operating principle, as well as its sensitization by natural dyes focusing on sepia melanin has been provided in this master’s dissertation. The obtained results in investigating the morphology, chemical composition, crystalline structure as well as optical properties of sepia melanin samples using Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), Energy x-ray diffraction, X-ray Diffraction (XRD), Fourier Transform Infrared spectroscopy (FTIR), Raman spectroscopy, UV-VIS absorption spectroscopy as well as Photoluminescence (PL) for Grätzel solar cell application have been reported. These results represent an important step forward in defining the structure of melanin. The results clearly show that sepia melanin can be used as natural dye to DSSC sensitization. It is promising for the realization of high cell performance, low-cost production, and non-toxicity. It should be emphasized here that natural dyes from food are better for human health than synthetic dyes. / Physics / 1 online resource (xii, 101 leaves) : illustrations / M. Sc. (Physics)

Vor dem Hintergrund der zukünftigen Notwendigkeit einer nachhaltigen Energieversorgung beschäftigt sich die vorliegende Arbeit mit Technologien der regenerativen Energiequelle Solarenergie, insbesondere Photovoltaik (PV). Systeme zur Nutzung der unerschöpflich verfügbaren, sauberen und im Prinzip “frei Haus” gelieferten Energie der Sonne können eine bedeutsame Rolle in einer umweltverträglicheren Zukunft spielen. Allerdings ist die Herstellung der erforderlichen Komponenten heute i.d.R. noch energie- und kostenintensiv, weshalb für eine korrekte Bewertung dieser Technologien der gesamte Lebenszyklus betrachtet werden muss. Zur tieferen Analyse der PV wird die Methodik des Environmental Life Cycle Costing (ELCC) auf der Grundlage von drei Grundideen eingeführt. Konkret sind dies die Ausgangspunkte: Nachhaltigkeit, Lebenszyklusdenken und die Drei-Dimensionalität dieses Instrumentes durch die gemeinsame Betrachtung ökologischer, ökonomischer und technischer Aspekte in ihrem Zusammenspiel. Ausgehend von theoretischen Elementen der Ökobilanzierung (Life Cycle Assessment) und des Life Cycle Costings, verbunden mit den technischen Eigenschaften der Photovoltaik werden wichtigste Anforderungen und Schritte für die Durchführung eines ELCC für PV beschrieben. Mittels einer softwaregestützten Inhaltsanalyse wird im Anschluss der definierte Rahmen für ein ELCC für PV getestet (und modifiziert) gegen eine Auswahl von 135 bereits existierender Studien, die sich mit dem Lebenszyklus von PV-Technologien aus ökologischer und ökonomischer Sicht beschäftigen. Im Ergebnis hieraus können die wichtigsten Elemente eines ELCC für PV, wie beispielsweise ökologische Wirkungskategorien oder ökonomische Indikatoren, identifiziert werden (methodisches Feedback). In einem nächsten Schritt werden die Studien hinsichtlich ihrer “Qualität” bezogen auf ökologische, ökonomische und übergreifende Inhalte eines ELCC für PV bewertet. Auf diese Weise kann ein Inventar von Lebenszyklusanalysen für PV erstellt werden, das nach den Technologien und der inhaltlichen Qualität bezüglich eines ELCC strukturiert ist und für weitere Analysen als Grundlage dienen kann. Aus den bisherigen Ergebissen kann eine erste Einschätzung zum aktuellen Stand des ELCC für PV in der Literatur vorgenommen werden: Es existiert bereits ein großer Pool von Studien, die sich mit dem Lebenszyklus der PV beschäftigen. Mit Blick auf die Anforderungen eines ELCC für PV besteht jedoch Nachholbedarf in der Verbindung und gemeinsamen Betrachtung von hot spots und trade offs aus ökologischer und ökonomischer Perspektive. Der definierte theoretische Rahmen für ein ELCC für PV, die kodierten Studien sowie das erstellte Inventar von Lebenszyklusanalysen der PV können nun als Grundlage für weitere Analysen dienen. Insbesondere eine inhaltliche Auswertung der konkreten Ergebnisse von Studien kann so einen Benchmark und Orientierung für neue Lebenszyklusanalysen für PV-Technologien liefern. / The special need of a sustainable energy supply in mind the technologies of the renewable source solar energy, especially photovoltaics (PV) is main subject of the present thesis. Using the inexhaustible, clean and “freely delievered” power from the sun solar devices may play a major role in a cleaner future, but, on the other hand, they are still energy consuming and expensive in their production which consequently demands a whole life cycle perspective when assessing this technology. For a closer look at PV the methodology of Environmental Life Cycle Costing (ELCC) is introduced by following three theoretical points of view. Namely these are sustainability, life cycle thinking and the three dimensional nature of this tool by regarding environmental, economic and technical aspects in their interaction. Based on theoretical elements of Life Cycle Assessment and Life Cycle Costing in combination with the technical background of photovoltaics main requirements and steps for performing an ELCC for PV are described. By executing software based content analysis the defined framework is checked (and modified) against a choice of 135 existing studies analyzing the life cycle of PV technologies from an environmental or economic perspective. As a result the main elements of an ELCC for PV, e.g. environmental impact categories and economic indicators, are identified (methodological feedback). Within the next step the existing studies are rated by their “quality” regarding the environmental, economic and more general parts of an ELCC for PV in order to create an inventory of life cycle studies for PV. This inventory is structured by technologies as well as quality of content respecting ELCC and might be used for further analyses. At this stage the results propose the possibility of a first estimate of the present status of ELCC for PV: until now there is a good pool of existing analyses of the life cycle of PV systems. But from an ELCC perspective the examination of common hot spots and trade offs between economic and environmental aspects should be expanded. The theoretical framework of ELCC for PV, the encoded studies and the inventory of life cycle analyses for PV are now the starting point for further analyses, especially of the individual outcome within studies, which will then pose a benchmark for new life cycle studies of PV technology.

Elektronische Bauteile aus organischen Halbleitern stellen höchste Anforderungen an die Qualität der Verkapselung, die sie vor eindringenden Wasser- und Luftmolekülen schützt. Gleichzeitig soll diese preiswert und mechanisch flexibel sein. Diese Arbeit realisiert Aluminium-Mehrschichtsysteme als wirkungsvolle, biegsame und einfache Verkapselung. Es werden verschiedene Herstellungsmethoden und Zwischenschichtmaterialien untersucht, wobei die Barrierelamination als überlegenes Verfahren etabliert wird. Verkapselungssysteme werden mittels optischer Untersuchung und mit dem elektrischen Calciumtest auf ihre Güte geprüft, bevor sie in Solarzellenalterungsexperimenten unter realitätsnahen Bedingungen zur Anwendung kommen. Laminationsbarrieren aus Aluminiumdünnschichten zeigen reproduzierbar Wasserdampfdurchtrittsraten im unteren 10^(-4) g(H2O)/m^2/Tag-Bereich unter beschleunigten Permeationsbedingungen. Sie verlängern die T(50)-Lebensdauer von Solarzellen um einen Faktor 50 gegenüber unverkapselten Zellen auf Werte, die mit starrer Glas- oder zeitaufwendiger ALD-Verkapselung vergleichbar sind. / Organic electronic devices require excellent encapsulation to protect them from intruding water- and air-molecules. At the same time, the encapsulation has to be inexpensive and flexible. This work presents aluminum multilayer barriers as highly effective, flexible and low-cost encapsulation. Various production methods and interlayer materials are investigated and barrier-lamination is established as superior process. Encapsulation systems are evaluated optically and by means of the electrical calcium-test, before they are employed in realistic solar cell aging experiments. Lamination-barriers of thin aluminum films show reproducible water-vapor transmission rates in the low 10^(-4) g(H2O)/m^2/day-range under accelerated permeation conditions. They improve the T(50)-lifetime of solar cells by a factor of 50 compared to unencapsulated cells, reaching values on par with rigid glass encapsulation or time-consuming atomic layer deposition.