Os aços inoxidáveis duplex são materiais com um excelente desempenho, devido às suas sobressalentes propriedades mecânicas e excelente resistência à corrosão. Uma composição química adequada e microestrutura balanceada são as responsáveis por esta combinação de propriedades. No entanto, são estes mesmos fatores que os fazem especialmente susceptíveis à precipitação de fases intermetálicas, com efeitos maléficos no seu desempenho. Durante os ciclos térmicos de uma soldagem multipasse, a precipitação de intermetálicos é crítica. Foi desenvolvido um método para simular os ciclos térmicos de uma solda multipasse. Usando este método, foi estudada a precipitação de nitreto de cromo e fase sigma na zona afetada pelo calor submetida a temperaturas abaixo de 950°C dos aços inoxidáveis duplex UNS S31803 e S32550. Foram estudadas energias de soldagem na faixa de 0,4 a 1,0 kJ/mm. Foi determinada mediante extração de precipitados, seguida de difração de raios X na câmara de Debye-Scherrer e microscopia eletrônica de transmissão, a precipitação de nitreto de cromo para energias de soldagem de 0,4 a 1,0 kJ/mm e de fase sigma para energias de soldagem de 0,6-1,0 KJ/mm, no UNS S32550. Já o UNS S31803 não apresentou precipitação alguma para as energias de soldagem estudadas. Baseando-se nos resultados verifica-se que durante uma soldagem multipasse o UNS S31803 é menos propenso que o UNS S32550 à precipitação de intermetálicos na zona afetada pelo calor submetida a temperaturas abaixo de 950°C. / Duplex stainless steels belong to a group of high performance stainless steels regarding to corrosion and mechanical properties. These achievements are related to a suitable chemical composition and a balanced microstructure. During welding thermal cycles the microstructure changes and, consequently, corrosion and mechanical properties might be impaired due to a precipitation of intermetallic phases. This precipitation is an issue to be addressed for multipass welding. It was developed a method for simulate the multipass welding thermal cycles. Using this method chromium nitride and sigma phase precipitation was studied in a simulated heat affected zone of multipass welding (three passes) of UNS S31803 and UNS S32550 duplex stainless steels with different heat inputs (0,4 to 1,0 kJ/mm). The HAZ simulated region was below 950°C maximum temperature. Microstructural characterization of simulated samples showed discontinuous films of a precipitated phase at ferrite/ferrite grain boundaries and ferrite/austenite interfaces were observed only in a UNS S32550 duplex grade for all heat inputs simulated. This suggests that sigma phase and chromium nitride precipitation took place during sample thermocycling. X-ray diffraction in a Debye-Scherrer chamber of extracted precipitates and electron diffraction by TEM confirmed the presence of chromium nitrides for all range of heat input studied and sigma phase for heat input above 0,6 kJ/mm. On the other hand, microstructural analysis of UNS S31803 simulated samples did not present precipitation of intermetallic phases in the tested temperature range of HAZ. Based on these results, UNS S31803 is more resistant than UNS S32550 to intermetallic phases precipitation in multipass welding.

Super duplex stainless steel (SDSS) has found a wide use in demanding applications such as offshore, chemical and petrochemical industries thanks to its excellent combination of mechanical properties and corrosion resistance. Welding of SDSS, however, is associated with the risk of precipitation of secondary phases and formation of excessive amounts of ferrite in the weld metal and heat affected zone. The present study was therefore aimed at gaining knowledge about the effect of multiple welding thermal cycles on the microstructure and possible sensitization to corrosion of welds in SDSS.Controlled and repeatable thermal cycles were produced by robotic welding. Oneto four autogenous TIG-remelting passes were applied on 2507 type SDSS plates using low or high heat inputs with pure argon as shielding gas. Thermal cycles were recorded using several thermocouples attached to the plates. Thermodynamic calculations and temperature field modelling were performed in order to understand the microstructural development and to predict the pitting corrosion resistance. Etching revealed the formation of different zones with characteristic microstructures: the fused weld zone (WZ) and the heat affected zone composed of the fusion boundary zone (FBZ), next to the fusion boundary, and further out Zone 1 (Z1) and Zone 2 (Z2). The WZ had a high content of ferrite and often nitrides which increased with increasing number of passes and decreasing heati nput. Nitrogen content of the WZ decreased from 0.28 wt.% to 0.17 wt.% after four passes of low heat input and to 0.10 wt.% after four passes of high heatinput. The FBZ was reheated to high peak temperatures (near melting point) and contained equiaxed ferrite grains with austenite and nitrides. Zone 1 was free from precipitates and the ferrite content was similar to that of the unaffected base material. Sigma phase precipitated only in zone 2, which was heated to peak temperatures in the range of approximately 828°C to 1028°C. The content of sigma phase increased with the number of passes and increasing heat input.  All locations, except Z1, were susceptible to local corrosion after multiplere heating. Thermodynamic calculations predicted that a post weld heat treatment could restore the corrosion resistance of the FBZ and Z2. However, the pitting resistance of the WZ cannot be improved significantly due to the nitrogen loss. Steady state and linear fitting approaches were therefore employed to predict nitrogen loss in autogenous TIG welding with argon as shielding gas. Two practical formulas were derived giving nitrogen loss as functions of initial nitrogen content and arc energy both predicting a larger loss for higher heat input and higher base material nitrogen content. A practical recommendation based on the present study is that it is beneficial to perform welding with a minimum number of passes even if this results in a higherheat input as multiple reheating strongly promotes formation of deleterious phases.

Duplex stainless steel (DSS) that developed in the 1930’s is a type of steel that consists of bothaustenite and ferrite phases in an almost equal proportion. It inherits properties of both ferriticand austenitic stainless steel and so it has good mechanical and corrosion resistance propertiesthat makes it suitable material in different industries with aggressive environment. There aredifferent approaches that used to evaluate the susceptibility of stainless steels to pitting corrosionlike Pitting Resistance Equivalent Number (PREN) and electrochemical methodologies. In thisstudy, focus is on the potentiodynamic (AL 101 5170) and potentiostatic (ASTM G150) testmethods as laboratory evaluations in which standard DSS (2205) is exposed to the differentchloride concentrations 0.1 M and 1 M respectively. In these methods parameters like PittingPotential (Ep) and Critical Pitting Temperature (CPT) can be measured respectively and used topredict the susceptibility of DSS to pitting corrosion. DSS owes its good corrosion resistance tothe oxide film that protects the metal from corrosion. Pitting can be initiated as a result of anyheterogeneities on the metal surface which act as a passive film defect like non-metallicinclusions and intermetallic precipitations such as sigma phase when metal is exposed toaggressive environment and high temperature. The aim of the present work is to make acomparison between two electrochemical methods besides finding how inclusions andmicrostructure can have impact on their results and on pitting corrosion. The results of theexperiment shows that there is a positive linear relation only in longitudinal direction betweenCPT and Ep. Also, among two test methods only ASTM G150 can detect sigma phase existence(<3%). Based on investigations in this experiment, inclusion characteristics such as numberdensity and composition has compatible results in both methods so that samples with big sizeinclusions (>8 μm) have negative effect on corrosion resistance and in terms of composition,samples with nitride inclusions has lower CPT and Ep compared with those with only oxide oroxide/sulfide inclusions. It is also discovered that phase arrangement is not the same in allspecimens that produced by different production methods and samples with finer phases havehigher CPT values in both longitudinal and transvers directions. However, this shape ofmicrostructure only affect the Ep in longitudinal directions but not transvers.

The focus of this master’s thesis is on the heat treatment of Ni-base alloys, specifically the risk of intermetallic σ-phases during different stages of heat treatment. The alloy studied is Sanicro®28, a super-austenitic stainless steel produced by Alleima AB. The problem at hand is that the quench-annealing stage is in high demand at the manufacturing facility, and the goal is to investigate if it can be removed from the manufacturing route. During forging, the outer surface and bar-ends can reach low temperatures, posing a high risk of σ-phase precipitation. Additionally, a necklace structure with large grains surrounded by fine re-crystallization is often observed at the surface of forged superalloys/Ni-base alloys. Today, this forged structure is re-crystallized and σ-phase dissolved during the quench-annealing stage. An alternative to quench-annealing after forging is to re-heat the bar using a Car Wagon Furnace(CWF). The thesis includes two laboratory experiments simulating two stages of heat treatment, the CWF and induction furnaces/soaking. The samples subjected to simulated CWF treatment showed re-crystallization throughout the entire structure. Annealing in CWF removes the large grains in surface positions. The time in the CWF also showed to be sufficient to dissolve σ-phase present from forging. Samples heated to the induction furnace set temperature do not contain precipitates, while temperatures below the induction set temperature induce σ precipitation to varying degrees. The key findings of the thesis are as follows: • Re-heating in a CWF right after forging is enough to dissolve σ-phase at half-radius and surface locations. • Quench-annealing stage could be removed by changing the route to a CWF after forging. • If temperatures fall below the σ-maximum stability temperature during induction furnace heating cycles, σ-phase precipitation occurs.

Projetos de instalações industriais com requisitos de assepsia e resistência à corrosão têm os aços inoxidáveis austeníticos como materiais de engenharia, e a liga AISI 316L é amplamente utilizada. A soldagem de chapas espessas é executada por processos MIG e a qualificação do procedimento de soldagem é realizada com base em propriedades mecânicas, avaliação insuficiente para aplicações que necessitam de uma película passiva resistente. A microestrutura da zona fundida da liga AISI 316L exerce influência sobre a resistência à corrosão, e há a necessidade de definir os mecanismos que governam a influência da fase sigma na resistência à corrosão. Inserido neste contexto, o objetivo do presente estudo foi avaliar a influência da fase sigma na resistência à corrosão em microrregiões de juntas soldadas multipasse da liga AISI 316L produzidas pelo processo MIG nos modos de transferência metálica pulsado, curto-circuito e spray. A metodologia consistiu em reproduzir amostras soldadas com parâmetros de soldagem aplicados na indústria para os modos de transferência metálica de interesse, com detalhada caracterização microestrutural da zona fundida de cada condição de soldagem. Em seguida, foram conduzidos ensaios eletroquímicos de corrosão em microrregiões da junta soldada em solução de 3,5% NaCl, e a influência da fase sigma na corrosão por pite foi avaliada por ensaio de imersão em solução de cloreto férrico (6% FeCl3). Caracterizou-se a área exposta à varredura por técnicas de microscopia ótica, microscopia eletrônica de varredura e microanálise química. A soldagem no modo pulsado resultou em uma zona fundida com microestrutura bifásica com a mais baixa fração volumétrica de ferrita delta, de refinada morfologia e isenta de fase sigma, proporcionando o mais nobre desempenho nos ensaios de corrosão, que se manifestou pelo mecanismo de corrosão localizada. A avaliação da área exposta à varredura demonstrou que, previamente a corrosão por pite, a corrosão incia-se de forma localizada, contudo, sem corrosão preferencial de uma das fases, característica que proporcionou parâmetros eletroquímicos mais nobres do que aqueles com corrosão seletiva de fases. Está característica é atribuída à ausência da fase sigma na microestrutura da zona fundida do modo pulsado. No modo curto-circuito ocorreu à decomposição eutetóide da ferrita delta formando a austenita secundária e a fase sigma, sendo está última precipitada principalmente no interior da ferrita delta. A morfologia da corrosão se dá, na fase inicial, como corrosão seletiva de fases, com degradação preferencial da austenita secundária e em direção a ferrita delta, devido à fragilização desta fase pela precipitação de fase sigma em seu interior. A degradação seletiva das fases austenita secundária e ferrita delta causam danos localizados ao filme passivo e, nestas regiões empobrecidas de cromo e molibdênio, ocorre à corrosão por pite. O modo spray com a mais elevada energia de soldagem resultou em uma ferrita delta grosseira e com estreitas bandas de austenita na microrregião de enchimento do chanfro e na raiz da solda, com alto índice de fase sigma nestas localizações. O processo corrosivo da zona fundida caracterizou-se por corrosão seletiva da fase austenita secundária e em direção à matriz austenítica, uma vez que a fase sigma revestiu a ferrita delta, tornando-a a região de comportamento catódico entre o par galvânico formado entre as fases austenita e ferrita delta. A corrosão seletiva da matriz austenítica causa a fragilização localizada do filme passivo com consequente corrosão por pite. O trabalho realizado permite concluir que o potencial de pite foi reduzido com a presença de fase sigma e fases a esta associada, e justamente o modo pulsado obteve destacada resistência à corrosão em função da ausência da fase sigma em sua microestrutura. / Industrial plant designs with asepsis and corrosion resistance requirements have austenitic stainless steels as engineering materials, and the AISI 316L alloy is widely used. The welding of thick plates is performed by MIG processes and the qualification of the welding procedure is carried out based on mechanical properties, insufficient evaluation for applications that require a resistant passive film. The microstructure of the molten zone of the AISI 316L alloy influences the corrosion resistance, and it is necessary to define the mechanisms that govern the influence of the sigma phase on corrosion resistance. In this context, the aim of the present study was to evaluate the influence of the sigma phase on the corrosion resistance in microrregions of multipass welded joints of the AISI 316L alloy produced by MIG process with metal transfer in pulsed, short circuit and spray modes. The methodology consisted in reproducing welded samples with welding parameters applied in the industry for the modes of metallic transfer of interest, with detailed microstructural characterization of the molten zone of each welding condition. Then, electrochemical corrosion tests were carried out in microrregions of the welded joint in 3.5% NaCl solution, and the influence of the sigma phase on pitting corrosion was evaluated by immersion test in ferric chloride solution (6% FeCl3). The area exposed to the scanning was characterized by optical microscopy, scanning electron microscopy and chemical microanalysis. Pulsed mode welding resulted in a molten zone with a biphasic microstructure with the lowest volume fraction of delta ferrite, refined morphology and sigma phase free, providing the noblest performance in the corrosion tests, which occurred in the form of localized corrosion. The evaluation of the area exposed to the scan showed that, prior to pitting corrosion, the corrosion started in a localized manner, however, without preferential corrosion of one of the phases, a characteristic that gave better electrochemical parameters than those with selective corrosion of phases. This characteristic is attributed to the absence of the sigma phase in the microstructure of the molten zone of the pulsed mode. In the short-circuit mode, the eutectoid decomposition of the delta ferrite formed the secondary austenite and the sigma phase, the latter being mainly precipitated inside the delta ferrite. The corrosion morphology occurs in the initial phase as selective corrosion of phases, with preferential degradation of the secondary austenite and towards the ferrite delta, due to the embrittlement of this phase by the precipitation of the sigma phase inside. The selective degradation of the secondary austenite and delta ferrite phases causes localized damage to the passive film and, in these impoverished regions of chromium and molybdenum, occurs to pitting corrosion. The spray mode with the highest welding energy resulted in a coarse delta ferrite with narrow bands of austenite in the chamfer filling microrregion and at the root of the weld, with a high sigma phase index at these locations. The corrosive process of the molten zone was characterized by selective corrosion of the secondary austenite phase and towards the austenitic matrix, since the sigma phase covered the delta ferrite, making it the region of cathodic behavior between the galvanic pair formed between the austenite and ferrite delta phases. Selective corrosion of the austenitic matrix causes localized embrittlement of the passive film with consequent pitting corrosion. The study accomplished allows concluding that the pitting potential was reduced with the presence of sigma phase and phases associated with it, and precisely the pulsed mode obtained outstanding corrosion resistance due to the absence of the sigma phase in its microstructure.

Projetos de instalações industriais com requisitos de assepsia e resistência à corrosão têm os aços inoxidáveis austeníticos como materiais de engenharia, e a liga AISI 316L é amplamente utilizada. A soldagem de chapas espessas é executada por processos MIG e a qualificação do procedimento de soldagem é realizada com base em propriedades mecânicas, avaliação insuficiente para aplicações que necessitam de uma película passiva resistente. A microestrutura da zona fundida da liga AISI 316L exerce influência sobre a resistência à corrosão, e há a necessidade de definir os mecanismos que governam a influência da fase sigma na resistência à corrosão. Inserido neste contexto, o objetivo do presente estudo foi avaliar a influência da fase sigma na resistência à corrosão em microrregiões de juntas soldadas multipasse da liga AISI 316L produzidas pelo processo MIG nos modos de transferência metálica pulsado, curto-circuito e spray. A metodologia consistiu em reproduzir amostras soldadas com parâmetros de soldagem aplicados na indústria para os modos de transferência metálica de interesse, com detalhada caracterização microestrutural da zona fundida de cada condição de soldagem. Em seguida, foram conduzidos ensaios eletroquímicos de corrosão em microrregiões da junta soldada em solução de 3,5% NaCl, e a influência da fase sigma na corrosão por pite foi avaliada por ensaio de imersão em solução de cloreto férrico (6% FeCl3). Caracterizou-se a área exposta à varredura por técnicas de microscopia ótica, microscopia eletrônica de varredura e microanálise química. A soldagem no modo pulsado resultou em uma zona fundida com microestrutura bifásica com a mais baixa fração volumétrica de ferrita delta, de refinada morfologia e isenta de fase sigma, proporcionando o mais nobre desempenho nos ensaios de corrosão, que se manifestou pelo mecanismo de corrosão localizada. A avaliação da área exposta à varredura demonstrou que, previamente a corrosão por pite, a corrosão incia-se de forma localizada, contudo, sem corrosão preferencial de uma das fases, característica que proporcionou parâmetros eletroquímicos mais nobres do que aqueles com corrosão seletiva de fases. Está característica é atribuída à ausência da fase sigma na microestrutura da zona fundida do modo pulsado. No modo curto-circuito ocorreu à decomposição eutetóide da ferrita delta formando a austenita secundária e a fase sigma, sendo está última precipitada principalmente no interior da ferrita delta. A morfologia da corrosão se dá, na fase inicial, como corrosão seletiva de fases, com degradação preferencial da austenita secundária e em direção a ferrita delta, devido à fragilização desta fase pela precipitação de fase sigma em seu interior. A degradação seletiva das fases austenita secundária e ferrita delta causam danos localizados ao filme passivo e, nestas regiões empobrecidas de cromo e molibdênio, ocorre à corrosão por pite. O modo spray com a mais elevada energia de soldagem resultou em uma ferrita delta grosseira e com estreitas bandas de austenita na microrregião de enchimento do chanfro e na raiz da solda, com alto índice de fase sigma nestas localizações. O processo corrosivo da zona fundida caracterizou-se por corrosão seletiva da fase austenita secundária e em direção à matriz austenítica, uma vez que a fase sigma revestiu a ferrita delta, tornando-a a região de comportamento catódico entre o par galvânico formado entre as fases austenita e ferrita delta. A corrosão seletiva da matriz austenítica causa a fragilização localizada do filme passivo com consequente corrosão por pite. O trabalho realizado permite concluir que o potencial de pite foi reduzido com a presença de fase sigma e fases a esta associada, e justamente o modo pulsado obteve destacada resistência à corrosão em função da ausência da fase sigma em sua microestrutura. / Industrial plant designs with asepsis and corrosion resistance requirements have austenitic stainless steels as engineering materials, and the AISI 316L alloy is widely used. The welding of thick plates is performed by MIG processes and the qualification of the welding procedure is carried out based on mechanical properties, insufficient evaluation for applications that require a resistant passive film. The microstructure of the molten zone of the AISI 316L alloy influences the corrosion resistance, and it is necessary to define the mechanisms that govern the influence of the sigma phase on corrosion resistance. In this context, the aim of the present study was to evaluate the influence of the sigma phase on the corrosion resistance in microrregions of multipass welded joints of the AISI 316L alloy produced by MIG process with metal transfer in pulsed, short circuit and spray modes. The methodology consisted in reproducing welded samples with welding parameters applied in the industry for the modes of metallic transfer of interest, with detailed microstructural characterization of the molten zone of each welding condition. Then, electrochemical corrosion tests were carried out in microrregions of the welded joint in 3.5% NaCl solution, and the influence of the sigma phase on pitting corrosion was evaluated by immersion test in ferric chloride solution (6% FeCl3). The area exposed to the scanning was characterized by optical microscopy, scanning electron microscopy and chemical microanalysis. Pulsed mode welding resulted in a molten zone with a biphasic microstructure with the lowest volume fraction of delta ferrite, refined morphology and sigma phase free, providing the noblest performance in the corrosion tests, which occurred in the form of localized corrosion. The evaluation of the area exposed to the scan showed that, prior to pitting corrosion, the corrosion started in a localized manner, however, without preferential corrosion of one of the phases, a characteristic that gave better electrochemical parameters than those with selective corrosion of phases. This characteristic is attributed to the absence of the sigma phase in the microstructure of the molten zone of the pulsed mode. In the short-circuit mode, the eutectoid decomposition of the delta ferrite formed the secondary austenite and the sigma phase, the latter being mainly precipitated inside the delta ferrite. The corrosion morphology occurs in the initial phase as selective corrosion of phases, with preferential degradation of the secondary austenite and towards the ferrite delta, due to the embrittlement of this phase by the precipitation of the sigma phase inside. The selective degradation of the secondary austenite and delta ferrite phases causes localized damage to the passive film and, in these impoverished regions of chromium and molybdenum, occurs to pitting corrosion. The spray mode with the highest welding energy resulted in a coarse delta ferrite with narrow bands of austenite in the chamfer filling microrregion and at the root of the weld, with a high sigma phase index at these locations. The corrosive process of the molten zone was characterized by selective corrosion of the secondary austenite phase and towards the austenitic matrix, since the sigma phase covered the delta ferrite, making it the region of cathodic behavior between the galvanic pair formed between the austenite and ferrite delta phases. Selective corrosion of the austenitic matrix causes localized embrittlement of the passive film with consequent pitting corrosion. The study accomplished allows concluding that the pitting potential was reduced with the presence of sigma phase and phases associated with it, and precisely the pulsed mode obtained outstanding corrosion resistance due to the absence of the sigma phase in its microstructure.

La phase sigma peut servir de prototype de phases topologiquement compactes, car la phase sigma possède une large gamme d'homogénéité et il existe de nombreuses données expérimentales disponibles pour la phase sigma. Dans le présent travail, les propriétés physiques, comprenant l'ordre atomique, le volume molaire, l'enthalpie de formation et le module d’élasticité isostatique, de la phase sigma binaire ont été étudiées en utilisant les calculs de premiers principes et la méthode CALPHAD combinée aux données expérimentales de la littérature.Tout d'abord, nous avons constaté que l'ordre atomique (c'est-à-dire la distribution du constituant atomique ou la préférence d'occupation du site sur les sites non équivalents d'une structure cristalline) de la phase sigma est affecté par le facteur de taille et la configuration électronique des éléments constitutifs. En outre, nous avons dissocié les effets de ces facteurs d'influence sur l'ordre atomique. Ensuite, nous avons mis en évidence un effet de l'ordre atomique sur l'enthalpie de formation, le module d’élasticité isostatique et le volume molaire. A l'état ordonné à 0K, la phase sigma a une faible enthalpie de formation et un grand module d’élasticité isostatique. L'influence de l'ordre atomique sur le volume molaire de la phase sigma dépend de la configuration électronique des deux éléments constitutifs. Par ailleurs, la base de données des volumes molaires des phases sigma binaires a été construite, ce qui devrait grandement faciliter la conception du matériau. Enfin, nous avons discuté de la prédiction de l'occupation du site de la phase sigma en utilisant la méthode CALPHAD combinée aux calculs de premiers principes. / The sigma phase can serve as a prototype of topologically close-packed (TCP) phases, as the sigma phase bears a broad homogeneity range and there are numerous experimental data available for the sigma phase. In the present work, physical properties, including atomic order, molar volume, enthalpy of formation and bulk modulus, of the binary sigma phase were investigated by using first principles calculations and CALPHAD method combining with the experimental data from the literature. Firstly, we found that the atomic order (i.e. atomic constituent distribution or site occupancy preference on nonequivalent sites of a crystal structure) of the sigma phase is affected by the size factor and electron configuration of the constituent elements. Furthermore, we have dissociated the effect of the individual influencing factor on atomic order. Secondly, the atomic order is found affecting physical properties, such as enthalpy of formation, bulk modulus and molar volume. When in the ordered state at 0K, the sigma phase shows a low enthalpy of formation and a large bulk modulus. The influence of atomic order on the molar volume of the sigma phase depends on the electron configuration of the two constituent elements. Thirdly, the molar volume database of the binary sigma phase has been built up within the CALPHAD framework, which can greatly facilitate material design. Finally, we tentatively discussed the site occupancy prediction of the sigma phase by using the CALPHAD method combined with first-principles calculations.

Les aciers inoxydables lean duplex sont une famille d'aciers austéno-ferritiques allégés en nickel et en molybdène, qui s'est développée à la fin des années 1990. Le compromis propriétés mécaniques, propriétés de résistance à la corrosion et coût de matière première place cette famille comme une alternative intéressante aux aciers austénitiques standards, et en particulier aux 304/304L qui représentent actuellement les deux tiers de la production d'acier inoxydable. Cependant, cette famille étant relativement récente, la stabilité en température des aciers lean duplex a été relativement peu étudiée, en particulier lors de maintiens prolongés en température. Dans le cadre de cette thèse, l'évolution microstructurale d'un acier lean duplex 2101 a été étudiée, lors de vieillissements isothermes à des températures comprises entre 20 °C et 850 °C, pour des temps s'échelonnant de quelques minutes à plusieurs mois. Les cinétiques de vieillissement ont été suivies par mesures de pouvoir thermoéléctrique (PTE), à partir desquelles des états vieillis ont été sélectionnés pour être caractérisés par microscopie électronique et par sonde atomique tomographique. A des températures intermédiaires de 350 – 450 °C, la ferrite de l'acier lean duplex 2101 est sujette à la démixtion Fe-Cr et à la formation d'amas enrichis en Ni-Mn-Si-Al-Cu, malgré les faibles teneurs en nickel de cette nuance. Ces phénomènes sont détectés par une forte augmentation du PTE. Pour des températures plus élevées, à 700 °C environ, une approche multi-techniques et multi-échelles a permis de décrire précisément les mécanismes qui régissent les différentes évolutions microstructurales : la germination et la croissance de M23C6 et de Cr2N, observés dès quelques minutes de vieillissement aux joints de phases, la précipitation de la phase σ pour des temps de vieillissement plus importants qui s'accompagne d'une transformation de la ferrite δ en austénite secondaire γ2, et la transformation partielle de l'austénite en martensite lors du refroidissement des échantillons vieillis. L'effet des différentes phases sur le PTE de l'acier lean duplex peut être décrit qualitativement lors du vieillissement par une loi des mélanges. / Lean duplex stainless steels are austeno-ferritic steels with lower nickel and molybdenum contents, developed in the late 90's. Considering mechanical properties, corrosion resistance and cost of raw material, this family is an interesting alternative to standard austenitic stainless steels, which currently represent two thirds of stainless steel production. However, lean duplex steels are relatively recent and their thermal stability has been relatively little studied, especially during long term aging. In this study, the microstructural evolution of a lean duplex steel 2101 was studied during isothermal aging at temperatures between 20 °C and 850 °C, from few minutes to several months. Aging kinetics were followed by thermoelectric power measurements (TEP), from which aged states were selected to be characterized by electron microscopy and atom probe tomography. At intermediate temperatures of 350 - 450 °C, Fe-Cr demixing and precipitation of Ni-Mn-Al-Si-Cu occur in the ferrite despite the low nickel content of this grade, leading to an increase in the TEP. For higher temperatures, at about 700 °C, the mechanisms which govern the different microstructural evolutions have been described by a multi-scale approach: the nucleation and growth of M23C6 and Cr2N, observed from few minutes of aging and the σ phase precipitation, observed for longer aging time. The latter is accompanied by a transformation of δ ferrite in γ2 secondary austenite, and by the partial transformation of austenite into martensite during cooling. The effect of different phases on the TEP of the lean duplex steel can be qualitatively described during aging by a rule of mixture.

The majority of UK’s intermediate level radioactive waste is currently stored in 316L and 304L austenitic stainless steel containers in interim storage facilities for permanent disposal until a geological disposal facility has become available. The structural integrity of stainless steel canisters is required to persevere against environmental degradation for up to 500 years to assure a safe storage and disposal scheme. Hitherto existing severe localised corrosion observances on real waste storage containers after 10 years of exposure to an ambient atmosphere in an in-land warehouse in Culham at Oxfordshire, however, questioned the likelihood occurrence of stress corrosion cracking that may harm the canister’s functionality during long-term storage. The more corrosion resistant duplex stainless steel grade 2205, therefore, has been started to be manufactured as a replacement for the austenitic grades. Over decades, the threshold stress corrosion cracking temperature of austenitic stainless steels has been believed to be 50-60°C, but lab- and field-based research has shown that 304L and 316L may suffer from atmospheric stress corrosion cracking at ambient temperatures. Such an issue has not been reported to occur for the 2205 duplex steel, and its atmospheric stress corrosion cracking behaviour at low temperatures (40-50°C) has been sparsely studied which requires detailed investigations in this respect. Low temperature atmospheric stress corrosion cracking investigations on 2205 duplex stainless steel formed the framework of this PhD thesis with respect to the waste storage context. Long-term surface magnesium chloride deposition exposures at 50°C and 30% relative humidity for up to 15 months exhibited the occurrence of stress corrosion cracks, showing stress corrosion susceptibility of 2205 duplex stainless steel at 50°C.The amount of cold work increased the cracking susceptibility, with bending deformation being the most critical type of deformation mode among tensile and rolling type of cold work. The orientation of the microstructure deformation direction, i.e. whether the deformation occurred in transverse or rolling direction, played vital role in corrosion and cracking behaviour, as such that bending in transverse direction showed almost 3-times larger corrosion and stress corrosion cracking propensity. Welding simulation treatments by ageing processes at 750°C and 475°C exhibited substantial influences on the corrosion properties. It was shown that sensitisation ageing at 750°C can render the material enhanced susceptible to stress corrosion cracking at even low chloride deposition densities of ≤145 µm/cm². However, it could be shown that short-term heat treatments at 475°C can decrease corrosion and stress corrosion cracking susceptibility which may be used to improve the materials performance. Mechanistic understanding of stress corrosion cracking phenomena in light of a comprehensive microstructure characterisation was the main focus of this thesis.