Molecules adsorbed on two-dimensional (2D) materials can show interesting physical and chemical properties. This thesis presents scanning probe microscopy (SPM) investigation of emerging 2D materials, molecular nanostructures on 2D substrates at the nanometer scale, and biophysical processes on the biological membrane. Two main techniques of nano-probing are used: scanning tunneling microscopy (STM) and atomic force microscopy (AFM). The study particularly emphasizes on self-assembled molecules on flat 2D materials and quasi-1D wrinkles. First, we report the preparation of novel 1D C60 nanostructures on rippled graphene. Through careful control of the subtle balance between the linear periodic potential of rippled graphene and the C60 surface mobility, we demonstrate that C60 molecules can be arranged into a 1D C60 chain structure of two to three molecules in width. At a higher annealing temperature, the 1D chain structure transitions to a more closely packed, quasi-1D hexagonal stripe structure. The experimental realization of 1D C60 structures on graphene is, to our knowledge, the first in the field. It could pave the way for fabricating new C60/graphene hybrid structures for future applications in electronics, spintronic and quantum information. Second, we report a study on nano-morphology of potential operative donors (e.g., C60) and acceptors (e.g., perylenetetracarboxylic dianhydride, aka. PTCDA) on wrinkled graphene supported by copper foils. We realize sub-monolayer C60 and PTCDA on quasi-1D and quasi-2D real periodic wrinkled graphene, by carefully controlling the deposition parameters of both molecules. Our successful realization of acceptor-donor binary nanostructures on wrinkled graphene could have important implications in future development of organic solar cells. Third, we report an STM and spectroscopy study on atomically thin transition-metal dichalcogenides (TMDCs) material. TMDCs are emerging 2D materials recently due to their intriguing physical properties and potential applications. In particular, our study focuses on molybdenum disulfide (MoS2) mono- to few-layers and pyramid nanostructures synthesized through chemical vapor deposition. On the few-layered MoS2 nanoplatelets grown on gallium nitride (GaN) and pyramid nanostructures on highly oriented pyrolytic graphite (HOPG), we observe an intriguing curved region near the edge terminals. The measured band gap in these curved regions is consistent with the direct band gap in MoS2 monolayers. The curved features near the edge terminals and the associated electronic properties may contribute to understanding catalytic behaviors of MoS2 nanostructures and have potential applications in future electronic devices and catalysts based on MoS2 nanostructures. Finally, we report a liquid-cell AFM study on the endosomal protein sorting process on the biological lipid membrane. The sorting mechanism relies on complex forming between Tom1 and the cargo sorting protein, Toll interacting protein (Tollip). The induced conformational change in Tollip triggers its dissociation from the lipid membrane and commitment to cargo trafficking. This collaborative study aims at characterizing the dynamic interaction between Tollip and the lipid membrane. To study this process we develop the liquid mode of AFM. We successfully demonstrate that Tollip is localized to the lipid membrane via association with PtdIns3P (PI(3)P), a major phospholipid in the cell membrane involved in protein trafficking. / Ph. D. / Two-dimensional (2D) materials are layered materials with thickness of single atom or few atoms. The ultimate thickness leads to novel properties that are useful for a wide range of applications in photovoltaics, electronics and quantum information. In order to explore these properties at the nanometer scale, we used scanning probe techniques, i.e., scanning tunneling microscopy (STM) and atomic force microscopy (AFM), to perform comprehensive investigations on these emerging materials. 2D materials, such as graphene and atomically thin transition-metal dichalcogenides (TMDCs), are promising candidates for building economic, safe and mechanically flexible solar cells with desirable optical and electronic properties, e.g. tunable sunlight absorption. The first part of the thesis focuses on graphene, a single-atom-thick carbon sheet. We deposited key components in organic solar cells, such as perylenetetracarboxylic dianhydride (PTCDA) and C₆₀ molecules, on graphene. On these materials we observed various novel nanostructures, like quasi-1D C₆₀ nanochains. The second part of the thesis focuses on mono- to few-layered MoS₂, which can be used as an active layer in high-efficiency solar cells. Our study has important implications in improving efficiency of organic solar cells in the future. In the final part of the thesis, we extended our subject to the biological lipid membrane, a 2D material critical in biology, and biophysical processes occurring on the membrane. Using a liquid-cell AFM, we investigated the endosomal protein sorting process on the biological membranes. Our study contributes to understanding of the interactions between the adaptor proteins and cell membranes in the protein sorting process that guides proteins to their proper destinations.

CdSe thin films were deposited by thermal evaporation and e-beam evaporation techniques on to well cleaned glass substrates. Low dose of boron have been implanted on a group of samples. EDAX and X-ray patterns revealed that almost stoichiometric polycrystalline films have been deposited in (002) preferred orientation. An analysis of optical measurements revealed a sharp increase in absorption coefficient below 700 nm and existence of a direct allowed transition. The calculated band gap was around 1.7 eV. The room temperature conductivity values of the samples were found to be between 9.4 and 7.5x10-4 (&amp / #937 / -cm)-1 and 1.6x10-6 and 5.7x10-7 (&amp / #937 / -cm)-1for the thermally evaporated and e-beam evaporated samples respectively. After B implantation conductivity of these films increased 5 and 8 times respectively. Hall mobility measurements could be performed only on the thermally evaporated and B-implanted e-beam evaporated samples and found to be between 8.8 and 86.8 (cm2/V.s). The dominant conduction mechanism were determined to be thermionic emission above 250 K for all samples. Tunneling and v variable range hopping mechanisms have been observed between 150-240 K and 80- 140 K respectively. Photoconductivity &amp / #8211 / illumination intensity plots indicated two recombination centers dominating at the low and high regions of studied temperature range of 80-400 K. Photoresponse measurements have corrected optical band gap measurements by giving peak value at 1.72 eV.

Organic solar cells offer attractive properties for novel applications and continuous advances in material and concept development have led to significant improvements in device performance. To exploit their full potential (roll-to-roll production of flexible and top-illuminated devices, using e.g. opaque metal foil or textile as substrate), highly transparent, conductive, mechanically flexible, and cost-efficient top electrodes are of great importance. The current standard material indium tin oxide (ITO) is rigid, expensive and requires a high energy / high temperature deposition process, limiting ITO (and other transparent conductive oxides) to bottom electrode applications. This work presents fundamental investigations to understand and control the properties of transparent conductors and documents four different approaches to prepare transparent electrodes on top of efficient small molecule organic solar cells, with the aim to replace ITO. Fullerene C60 layers are investigated as completely carbon-based electrodes. For an optimized doping concentration, sheet resistance and transmittance are improved and efficient solar cells are realized. Since the lateral charge transport is still limited, a combination with a microstructured conductor is suggested. Pulsed laser deposition allows for the first time a damage-free preparation of gallium doped zinc oxide (ZnO:Ga) layers on top of organic devices by careful optimization of the deposition atmosphere. ZnO:Ga electrodes with a transmittance of Tvis = 82.7 % and sheet resistance Rs = 83 Ohm/sq are obtained. The formation of local shunts due to ZnO:Ga droplets is identified and then prevented by a shadow mask between the target and the sample, enabling solar cells with similar efficiency (2.9 %) compared to a reference device using a state-of-the-art metal top contact. Another very promising alternative are intrinsically flexible, ultra-thin silver layers. By introducing an oxide interlayer, the adverse interpenetration of silver and organic materials is prevented and the charge extraction from the solar cells is improved. With a second oxide layer on top, the silver electrode is significantly stabilized, leading to an increased solar cell lifetime of 4500 h (factor of 107). Scanning electron micrographs of Ag thin films reveal a poor wetting on organic and oxide substrates, which strongly limits the electrode performance. However, it is significantly improved by a 1 nm thin seed layer. An optimized Au/Ag film reaches Tvis = 78.1 % and Rs = 19 Ohm/sq, superior to ITO. Finally, silver electrodes blended with calcium show a unique microstructure which enables unusually high transmittance (84.3 % at 27.3 Ohm/sq) even above the expectations from bulk material properties and thin film optics. Such values have not been reached for transparent electrodes on top of organic material so far. Solar cells with a Ca:Ag top electrode achieve an efficiency of 7.2 %, which exceeds the 6.9 % of bottom-illuminated reference cells with conventional ITO electrodes and defines a new world record for top-illuminated organic solar cells. With these electrodes, semi-transparent and large-area devices, as well as devices on opaque and flexible substrates are successfully prepared. In summary, it is shown that ZnO:Ga and thin metal electrodes can replace ITO and fill the lack of high performance top electrodes. Moreover, the introduced concepts are not restricted to specific solar cell architectures or organic compounds but are widely applicable for a variety of organic devices.

L'objectif de ce travail de recherche est l'élaboration et l'optimisation de transistors à effet de champ organiques de type N (OTFTs). Des transistors en structure Bottom Gate Bottom Contact sont fabriqués à basse température T<120°C. Trois différentes molécules organiques conductrices d'électrons, déposées par évaporation thermiques, sont utilisées pour la couche active. Les OTFTs à base de la première molécule à corps LPP présentent de faibles mobilités à effet de champ de l'ordre de 10-5cm2/V.s. L'étude d'optimisation menée sur les conditions de dépôt de cette dernière n'a pas permis d'améliorer ses performances électriques. L'étude de stabilité électrique ''Gate Bias Stress'' a mis en évidence les instabilités de cette molécule. Les OTFTs à base des deux dérivés indénofluorènes (IF) possèdent des mobilités plus importantes. Dans les conditions optimales la molécule IF(CN2)2 méta permet d'atteindre une mobilité d'effet de champ µFE=2.1x10-4 cm2/V, alors que la molécule IF(CN2)2 para permet d'obtenir des mobilités µFE=1x10-2cm2/V.s après recuit. L'étude de stabilité électrique a mis en évidence une meilleure stabilité des OTFTs à base de IF(CN2)2 para. Une étude des phénomènes de transport de charges est menée pour les deux types de molécules. Les OTFTs de type N réalisés sont utilisés pour la réalisation d'un circuit logique de type inverseur pseudo-CMOS. Finalement, ce procédé basse température nous a permis de réaliser des OTFTs sur substrat flexible. / The main goal of this present work consists in the fabrication and optimization of N type organic field effect transistors. Bottom Gate Bottom Contact transistors are performed at low temperature T<120°C. Three different electro-deficient organic molecules are thermally evaporated and used as active layer. OTFTs based on LPP core molecule present low field effect mobility around 10-5cm2/V.s. The optimization study investigated on deposition parameters of this molecule on OTFTs performances does not allow improving this mobility. Moreover gate bias stress measurements reveal important instabilities related to this molecule. Indenfluorene derivatives core (IF) based OTFTs show better performances. Field effect mobility µFE=2.1x10-4 cm2/V is reached using IF(CN2)2 meta in optimized deposition conditions and µFE=1x10-2 cm2/V.s is obtained using IF(CN2)2 para after annealing treatment. The investigated gate bias stress study highlights the good electrical stability of IF(CN2)2 para based OTFTs. Temperature measurements allow us studying the charge transport phenomenon in these indenofluorene derivatives. Fabricated N-type OTFTs are used to perform a first electronic circuit that consists in a logic gate (invertor).Finally this low temperature process led us to achieve OTFTs devices on flexible substrates (PEN).

This diploma thesis deals with the preparation of the very thin films and their investigation by scanning probe microscopy methods. The ultrathin films of Pt on Pt(111) were created by pulsed laser deposition and the ultrathin films of Co on Pt(111) were deposited by thermal evaporation. The coverage of the substrate was much smaller than one monolayer (in order of hundredths of monolayer). The nucleation theory was verified by these experiments using so-called Onset method. Further graphene sheets were prepared on layer of Si/SiO2 by the mechanical exfoliation from the graphite crystal. The fabricated graphene sheets were studied by micro-Raman spectroscopy, microreflectometry, atomic force microscopy and similar techniques. These methods proved the thinnest graphite layers were consisted of two graphene monolayers.

Organic solar cells offer attractive properties for novel applications and continuous advances in material and concept development have led to significant improvements in device performance. To exploit their full potential (roll-to-roll production of flexible and top-illuminated devices, using e.g. opaque metal foil or textile as substrate), highly transparent, conductive, mechanically flexible, and cost-efficient top electrodes are of great importance. The current standard material indium tin oxide (ITO) is rigid, expensive and requires a high energy / high temperature deposition process, limiting ITO (and other transparent conductive oxides) to bottom electrode applications. This work presents fundamental investigations to understand and control the properties of transparent conductors and documents four different approaches to prepare transparent electrodes on top of efficient small molecule organic solar cells, with the aim to replace ITO. Fullerene C60 layers are investigated as completely carbon-based electrodes. For an optimized doping concentration, sheet resistance and transmittance are improved and efficient solar cells are realized. Since the lateral charge transport is still limited, a combination with a microstructured conductor is suggested. Pulsed laser deposition allows for the first time a damage-free preparation of gallium doped zinc oxide (ZnO:Ga) layers on top of organic devices by careful optimization of the deposition atmosphere. ZnO:Ga electrodes with a transmittance of Tvis = 82.7 % and sheet resistance Rs = 83 Ohm/sq are obtained. The formation of local shunts due to ZnO:Ga droplets is identified and then prevented by a shadow mask between the target and the sample, enabling solar cells with similar efficiency (2.9 %) compared to a reference device using a state-of-the-art metal top contact. Another very promising alternative are intrinsically flexible, ultra-thin silver layers. By introducing an oxide interlayer, the adverse interpenetration of silver and organic materials is prevented and the charge extraction from the solar cells is improved. With a second oxide layer on top, the silver electrode is significantly stabilized, leading to an increased solar cell lifetime of 4500 h (factor of 107). Scanning electron micrographs of Ag thin films reveal a poor wetting on organic and oxide substrates, which strongly limits the electrode performance. However, it is significantly improved by a 1 nm thin seed layer. An optimized Au/Ag film reaches Tvis = 78.1 % and Rs = 19 Ohm/sq, superior to ITO. Finally, silver electrodes blended with calcium show a unique microstructure which enables unusually high transmittance (84.3 % at 27.3 Ohm/sq) even above the expectations from bulk material properties and thin film optics. Such values have not been reached for transparent electrodes on top of organic material so far. Solar cells with a Ca:Ag top electrode achieve an efficiency of 7.2 %, which exceeds the 6.9 % of bottom-illuminated reference cells with conventional ITO electrodes and defines a new world record for top-illuminated organic solar cells. With these electrodes, semi-transparent and large-area devices, as well as devices on opaque and flexible substrates are successfully prepared. In summary, it is shown that ZnO:Ga and thin metal electrodes can replace ITO and fill the lack of high performance top electrodes. Moreover, the introduced concepts are not restricted to specific solar cell architectures or organic compounds but are widely applicable for a variety of organic devices.

In the recent years area organic photovoltaics is generating a lot of interests because whole process of synthesis and fabrication is less energy intensive process as well as it is cost effective compared to conventional inorganic Si based photovoltaic technology. This work mainly deals with the fabrication and optimization of device fabrication conditions for organic photovoltaic materials. In first part of the work, the solar cell fabrication conditions were optimized for the commonly used system P3HT – PCBM. The fabricated device was optimized for the solvents used for the active material, concentration of the active material solution, donor- acceptor ratio of the active material, annealing conditions of the active layer and the metal evaporation conditions for the cathode. All the optimization procedures were carried out in controlled atmosphere to minimize the environmental effect inference during fabrication of the solar cell devices. All the characterization was carried out at ambient conditions. The efficiency of the solar cell was improved from 0.009% to 6.2%. the environmental stability of the fabricated devices were carried out after encapsulating it with epoxy based resin in both ambient conditions as well as extreme conditions like 85% RH at 25°C inside the humidity chamber. It was observed that both the data matches well with each other indicating proper encapsulation required to safe guard the device for the better performance over the period of time. Second part of this work mainly deals with understanding the structure property relationship of thiophene based donor- acceptor- donor molecule 2,5-dithienyl-3,4-(1,8-naphthylene) cyclopentadienone (DTCPA), which is highly crystalline, low band gap organic molecule which absorbs over entire visible region of the solar spectra. DTCPA crystals of various morphologies were prepared by various recrystallization routes. It was observed that macro scale morphology of these crystals differs from each other. Also depending on the method of recrystallization sizes of the crystals also varies. All the recrystallized DTCPA shows strong orientation toward (001) direction. However, it was observed that lattice parameters of these crystals slightly differ from each other owing to the recrystallization methodology. These variations in crystal parameters are more than 0.02 which is significant. It was also observed that the crystallite sizes depend on the recrystallization routes. Slow evaporation of concentrated solution (SEC) grown crystals has the larger crystallite size of 170nm. It was observed that absorption range of these crystals slightly differ from each other owing to the change in the crystallite sizes and crystal parameters. Third part of this work deals with the fabrication and optimization of thermal evaporation process of DTCPA for photovoltaic applications. DTCPA is stable at higher temperatures as well as has sharp melting point which make it ideal candidate for thermal evaporation. In this work films of DTCPA were fabricated for various evaporation rates by thermal evaporation technique. Chemical integrity of the molecules upon evaporation is found to be intact as observed from FTIR spectroscopy. XRD shows that at lower (25 W/m2) as well as higher (40 W/m2) films are oriented to (001), (400) as well as (311) directions, at 30 W/m2 and 35 W/m2 there is a strong orientation towards (311) and (001) directions respectively. Photo luminescence studies indicate that there is strong 410 nm emission for films deposited at the power of 25 W/m2 and 40 W/m2. Microscopic studies confirm that morphology is dependent on the deposition rates as it changes with the change in deposition rate. This in turn reflects in the device characteristics of these films. It was observed that films deposited at high deposition rates show better device characteristics with high VOC and current density values. All these device fabrication and characterizations were carried out in ambient conditions. Fourth part of this work deals with P3HT - DTCPA composites which exhibit wide range of light absorption. It was observed that DTCPA act as nucleating centers for the P3HT molecules and increases crystallinity in the composite. Furthermore, DTCPA helps in exciton separation because of donor and acceptor moieties present in the molecule. It also helps in charge transportation because of its crystalline nature and further it induces molecular ordering in the P3HT matrix. The band diagram of P3HT- DTCPA suggests that the band edges of both materials are ideal for charge separation. In addition, crystalline nature of the DTCPA molecule helps in effective charge transportation. J-V characteristics shows that there is large built in potential in the devices from these blends leading to large Voc. Composites with lower DTCPA loadings show higher efficiency than with higher loadings. These devices were prepared in ambient conditions and needs to be optimized for obtaining better device properties. In the fifth part of the work two types of system were studied to understand the band edge matching on the photovoltaic properties, carbazole based copolymers and DTCPA based copolymers. In the case of carbazole based copolymers it was observed that by copolymerizing carbazole with thiophene based derivatives lowers the band gap and modifies the HOMO and LUMO levels for better suit for the photovoltaic device fabrication. It was observed that that is two orders of improvements in the efficiency by co polymerizing carbazole with benzothiodizole as improves the JSC and VOC. Also the copolymerization of carbazole with both benzothiodiazole and bithiophene results in better light harvesting as the optical band gap was lowered. In the case of DTCPA copolymers with DTBT and DHTBT as both are random copolymers the solubility was low as well as their HOMO band edge was mismatched with the PEDOT: PSS which is a hole transport layer. However, the alternate polymerization of DTCPA with DTBT improved the band edge matching and also the solubility. As a result there was tenfold improvement in the charge collection and hence the efficiency was improved from 0.02% to 2.4%. Many of the conducting polymers have good material property but poor filmability. In the sixth part of this work deals with fabrication of device quality films by alternate deposition technique like pulsed laser deposition. Two types of system were studied in this work (i) polypyrrole- MWCNT nanocomposites and (ii) Poly DTCPA polymer. In both the cases it was observed that chemical integrity of the polymer retained during ablation. PolyDTCPA films were fabricated by pulsed laser deposition by both IR (Nd-YAG) and UV (KrF) laser source. Morphological studies indicate that IR laser ablated films were particulate in nature whereas UV laser ablated films were grown as continuous layers as polyDTCPA absorbs better in UV region. As a result the IV characteristics indicate that IR laser ablated films are resistive in nature and UV laser ablated films are good rectifiers indicating the suitability of the process for fabrication of device quality films.

С помощью оборудования National Instruments реализованы две установки для нанесения органических покрытий. Установка термовакуумного нанесения с виртуальным прибором «ThermoVac» позволяет производить линейный нагрев испаряемого вещества с фиксированной скоростью до заданной температуры термостатирования в диапазоне от комнатной до 500 °C. Установка для нанесения методом центрифугирования с ВП «SC_organic» позволяет поддерживать заданную скорость вращения подложки в диапазоне от 500 до 9000 об/мин. На базе микрозондовой станции Cascade Microtech MPS150 разработан автоматизированный канал для тестирования мемристорных структур, в режиме многократного чтения и записи. ВП «RW MIM» формирует на выходе SMU источника последовательность импульсов заданной амплитуды и длительности в режимах запись/чтение. Выполнено нанесение и аттестация пленок 5,11-диметил-5,11-дигидроиндоло [3.2-b]карбазола и 5,11-дигексил-5,11-дигидроиндоло[3.2-b]карбазола. По измеренным вольтамперным характеристикам получено, что полупроводник в синтезированных структурах TiN/DMICZ/Au, Ti/DMICZ/Au обладает дырочной проводимостью с подвижностью μ = 4.9∙10-7 см2/(В∙с). Показано, что регистрируемая ВАХ характеризуется петлями гистерезиса, которые свидетельствуют о наличии мемристивного эффекта в образцах TiN/DHICZ/Au. Произведено тестирование исследуемых слоистых структур в режимах многократного чтения/записи. / An automated installation based on National Instruments equipment, two installations for applying organic coatings are implemented. The installation of a thermo vacuum evaporation with a virtual device "ThermoVac" allows linear heating of the evaporated substance at a fixed rate of up to 500 ° C. The centrifugal centrifugation unit with an VI “SC_organic” supports the specified rotation speed of the substrate in the range of 500 to 9000 rpm. Based on the microprobe station Cascade Microtech MPS150, an automated channel was developed for testing memristor structures, in the mode of multiple reading and writing. VI "RW MIM" forms a sequence of pulses of the specified amplitude and duration in the write / read modes at the SMU output of the source. The deposition and validation of 5,11-dimethyl-5,11-dihydroindolo [3.2-b] carbazole and 5,11-dihexyl-5,11-dihydroindolo [3.2-b] carbazole films was performed. From the measured volt-ampere characteristics, it was found that the semiconductor in the synthesized TiN / DMICZ / Au, Ti / DMICZ / Au structures has a hole conductivity with a mobility μ = 4.9 ∙ 10-7 cm2/(V∙s). It is shown that the recorded I-V characteristic is characterized by hysteresis loops that indicate the presence of a memorial effect in TiN / DHICZ / Au samples. The testing of layered structures under test in multiple read / write modes was performed.

The efficiency of organic light-emitting diodes (OLEDs) typically decreases with increasing current density. This so-called roll-off impedes the market entry of OLEDs in high-brightness applications such as general lighting. One of the most important processes causing roll-off is exciton annihilation, which evolves upon high exciton densities. This mechanism is especially pronounced in phosphorescent molecules due to their long triplet lifetime. In order to reduce the roll-off in phosphorescent OLEDs, this thesis focusses on decreasing the local exciton density by modifying the exciton lifetime, the spatial exciton distribution, and the tendency of emitters to form aggregates. The obtained results lead to a deeper understanding of efficiency roll-off and help sustaining the OLED efficiency at high brightness. The emitter lifetime can be influenced by the optical environment around the emitting dipoles through the Purcell effect. In order to study this effect, the distance between emitter and metal cathode is varied for two different OLED stacks. A strong influence of emitter position and orientation on roll-off is observed and explained by modelling the data with triplet-triplet annihilation theory. Furthermore, design principles for optimal high-brightness performance are established by simulating the roll-off as a function of emitter-cathode distance, emissive dipole orientation, and radiative efficiency. Next, a method is developed that allows extracting the spatial exciton distribution. Therefore, a thin sensing layer that locally quenches excitons is introduced into the emission layer at varying positions. The resulting quenching profile is then fitted using a comprehensive theory based on the diffusion equation, which renders the exciton distribution and diffusion length with nanometer resolution. This method is applied to an emission layer comprising an ambipolar host material. Contrary to expectations which suggest that ambipolar materials exhibit broad exciton formation, a narrow emission zone close to the electron transport layer is found. Additional explorations of structures that might broaden the emission zone point to a narrow emission zone in double emission layers and broader exciton formation in mixed emission layers. Previous investigations revealed a strong correlation between emitter aggregation and molecular dipole moment of the emitter. Within this thesis, the range of studied emitters is significantly extended. It is shown that homoleptic emitters show a stronger tendency to form aggregates than heteroleptic compounds. This is probably not only related to their higher dipole-dipole potential, but also to the molecular structure. Systematic analysis of the deposition parameters shows that aggregate formation depends on the underlying material and increases with increasing substrate temperature and decreasing evaporation rate. The two green emitters Ir(ppy)3 and Ir(ppy)2(acac) are additionally studied by means of X-ray diffraction. Both emitters form crystallite grains and exhibit a preferred orientation. Doping the emitters into an amorphous host, both orientation and crystallite formation retain at the investigated doping concentrations above 20 wt%. This result is a first step toward further understanding of the mechanism of transition dipole orientation. / Die Effizienz organischer Leuchtdioden (OLEDs) nimmt üblicherweise mit ansteigender Stromdichte ab. Dieser so genannte Roll-Off erschwert den Markteintritt von OLEDs in Bereichen, die hohe Helligkeiten erfordern, wie beispielsweise in der Beleuchtung. Einer der wichtigsten Prozesse, die zu Roll-Off führen, ist die Annihilation von Exzitonen. Diese nimmt mit steigender Exzitonendichte zu und ist vor allem in phosphoreszenten OLEDs aufgrund der dort vorhandenen langen Triplettlebensdauer ein großer Verlustfaktor. Im Rahmen dieser Dissertation werden Methoden vorgestellt, die mittels Reduzierung der Exzitonendichte den Roll-Off in phosphoreszenten OLEDs verringern können. Dazu gehören die Veränderung der Exzitonenlebensdauer, die Untersuchung der räumlichen Verteilung der Exzitonen und die Erforschung der Bildung von Emitteraggregaten. Die gewonnenen Ergebnisse führen zu einem besseren Verständnis des Effizienz Roll-Offs und helfen, die Effizienz von OLEDs bei hohen Helligkeiten zu verbessern. Die Emitterlebensdauer kann über den Purcell-Effekt durch Veränderung des die emittierenden Dipole umgebenden elektromagnetischen Felds beeinflusst werden. Dieser Effekt wird genutzt, indem der Abstand zwischen Emitter und Metallelektrode für zwei verschiedene OLED-Aufbauten variiert wird. Der Roll-Off ist stark abhängig von der Position und Orientierung des Emitters und kann durch Modellierung der Daten auf Basis von Triplett-Triplett-Annihilation erklärt werden. Durch Simulation des Roll-Offs in Abhängigkeit des Emitter-Kathode-Abstands, der Orientierung und der strahlenden Effizienz der emittierenden Dipole werden Prinzipien zur optimalen Leistung von OLEDs bei hohen Helligkeiten entwickelt. Als nächstes wird eine Methode eingeführt mittels derer die räumliche Exzitonenverteilung extrahiert werden kann. Dafür wird eine dünne Sensorschicht in die Emissionsschicht eingebracht, die lokal Exzitonen auslöscht. Unter Variation der Position des Sensors wird ein Profil der Auslöschungsintensität bestimmt. Die gemessene Intensität wird mittels einer umfassenden Theorie auf Grundlage der Diffusionsgleichung angepasst, wodurch sich die räumliche Verteilung der Exzitonen und die Diffusionslänge mit einer Auflösung von 1nm ergibt. Die Methode wird auf eine Emissionsschicht angewandt, die das ambipolare Matrixmaterial CBP enthält. Entgegen der Erwartung, dass die Exzitonenbildung in ambipolaren Materialien weiter ausgedehnt ist, ist die gemessene Emissionszone sehr schmal und befindet sich an der Grenze zur Elektronentransportschicht. Um eine Verbreiterung des Emissionsprofils zu ermöglichen, werden weitere Strukturen untersucht. Dabei wird eine schmale Emissionszone in Doppelemissionsschichten beobachtet, wohingegen gemischte Emissionsschichten zu einer Verbreiterung der Exzitonenbildung führen können. Vorangegangene Untersuchungen deckten einen Zusammenhang zwischen der Aggregation von Emittermolekülen und dem Dipolmoment des Emitters auf. In dieser Arbeit werden weitere Emittermoleküle untersucht, wobei eine stärkere Aggregation von homoleptischen Emittern im Vergleich zu heteroleptischen festgestellt wird. Dies ist einerseits im höheren Dipol-Dipol-Potential der homoleptischen Verbindungen und andererseits in der Molekülstruktur begründet. Eine systematische Analyse der Herstellungsparameter zeigt, dass die Aggregatbildung von dem darunter liegenden Material abhängt und mit steigender Substrattemperatur und sinkender Verdampfungsrate zunimmt. Die zwei Grünemitter Ir(ppy)3 und Ir(ppy)2(acac) werden zusätzlich mittels Röntgenspektroskopie untersucht. Beide Emitter bilden kristalline Körner und weisen eine bevorzugte Orientierung auf. Sowohl die Kristallbildung als auch die Orientierung bleiben erhalten, wenn die Emitter mit mehr als 20 Gewichtsprozent in das Matrixmaterial CBP dotiert werden. Dieses Ergebnis ist ein erster Schritt zum besseren Verständnis der in vielen Iridium-Emittern beobachteten Orientierung des Übergangsdipolmoments.

Auf dielektrische Substrate wurden Schichten aus Gold thermisch aufgedampft. Die Schichten wurden neben anderen Methoden wie AFM oder der Messung der Schichtleitfähigkeiten hauptsächlich mit Hilfe der spektroskopischen IR-Ellipsometrie (SIRE) in einem Schichtdickenbereich von 4 bis 60 nm systematisch untersucht. Aus den primär ermittelten ellipsometrischen Parametern tan(Psi) und Delta lassen sich der Brechungsindex n und der Absorptionsindex k bestimmen und auch weitere Größen wie z.B. der elektrische Widerstand bzw. die elektrische Leitfähigkeit errechnen. Die untersuchten Schichten lassen sich anhand der optischen, topographischen und elektrischen Eigenschaften in drei Gruppen einteilen: Dielektrische, aus isolierten Goldinseln bestehende Filme (4 bis 6 nm), Schichten in einem Übergangsbereich (8 bis ca. 16 nm), metallische Schichten (ab ca. 16 nm). Die dielektrischen Goldinselfilme zeigen optische Eigenschaften, die bislang für keine anderen Proben beschrieben worden sind. Der Brechungsindex n ist hoch (4 bis 9 bei 2400/cm) und der Absorptionsindex k klein (0 bis 4 bei 2400/cm). Beide Indizes sind spektral weitgehend konstant. Daß diese Filme dielektrische Eigenschaften besitzen, steht in direktem Widerspruch zur allgemeinen SEIRA-Literatur. Die Inselstruktur der dielektrischen Filme verursacht einen Verstärkungseffekt, der als Oberflächenverstärkte Infrarotabsorption (surface-enhanced infrared absorption - SEIRA) bekannt ist. Es zeigte sich, daß die optischen Konstanten der Filme einen erheblichen Einfluß auf die SEIRA-Verstärkung ausüben. Um Inselfilme mit reproduzierbaren optischen Eigenschaften herstellen zu können, wurde ein lithographisches Verfahren entwickelt. Auf einer geschlossenen, homogenen Goldschicht wurden monodisperse Nanopartikel aus Polystyrol (PS) in einer Monolage deponiert. Die PS-Nanopartikel dienten in einem trockenen Ätzprozeß im Ar-Plasma als lithographische Maske, um die darunterliegende Au-Schicht zu strukturieren. / Thin films were produced on dielectric substrates by thermal evaporation of gold in a high vacuum chamber. These films were investigated systematically in a range between 4 and 60 nm thickness. The method mainly applied was the spectroscopic IR-ellipsometry (SIRE), in addition to other methods like AFM or sheet resistance measurement. The primary results are the ellipsometric parameters tan(Psi) and Delta. They were used to determine the refractive index n and the absorption index k. Electrical parameters can also be calculated. Depending on the optical, topographical and electrical properties the population of different layers can be divided into three parts: dielectric films with isolated gold islands (4 to 6 nm), layers in a transient area (8 to ca. 16 nm), metal films (ca. 16 to 60 nm). The optical properties shown by dielectric gold island films were never before described for other samples. The refractive index n is high (4 to 9 at 2400/cm) and the absorption index small (0 to 4 at 2400/cm). Both indices are nearly constant in the spectral range. Directly in contrast to the SEIRA-literature the island films show dielectric properties. The island structure of the dielectric films gives rise to an enhancement effect called surface-enhanced infrared absorption (SEIRA). It could be shown that the optical constants of the island films have a considerable influence on the enhancement factors. A lithographic method was developed in order to find a way for manufacturing island films with reproducible optical properties. Monodispers polystyrene nanoparticles were deposited in a monolayer on a dense gold layer on a dielectric substrate. The layer of nanoparticles was used as a mask for a dry etch process in a reactive Ar-plasma.