De nouveaux glycopolymères amphiphiles en peigne de type dextrane-g-poly(méthacrylate de méthyle) ont été obtenus via une polymérisation radicalaire contrôlée par transfert d’atome (ATRP). Pour contrôler les paramètres macromoléculaires de ces glycopolymères potentiellement biocompatibles et en partie biodégradables, la stratégie de synthèse « grafting from » a été sélectionnée et appliquée selon deux voies de synthèse. La première voie comporte quatre étapes : acétylation partielle des fonctions hydroxyle du dextrane ; introduction des groupements amorceurs d’ATRP ; ATRP contrôlée du méthacrylate de méthyle dans le diméthylsulfoxyde ; hydrolyse des groupements acétate dans des conditions douces. La seconde voie de synthèse permet d’obtenir ces glycopolymères en seulement deux étapes : introduction directe des groupements amorceurs d’ATRP sur le dextrane ; ATRP contrôlée du méthacrylate de méthyle dans le diméthylsulfoxyde. Des études détaillées de chaque étape ont permis à la fois d’estimer la longueur de la chaîne de dextrane et d’assurer le contrôle de l’architecture des glycopolymères (nombre et longueur des greffons). Des études préliminaires par tensiométrie interfaciale ont permit d’évaluer le caractère tensioactif de ces glycopolymères / Synthesis of the new comb-like amphiphilic glycopolymer dextran-g-poly(methyl methacrylate) was obtained thanks to an Atom Transfert Radical Polymerization (ATRP). In order to control the macromolecular parameters of these biocompatible and partly biodegradable glycopolymers, the “grafting from” strategy was applied using two different multi-step pathways. The first one is composed of four steps: partial acetylation of dextran hydroxyl groups; introduction of initiator groups convenient for ATRP; ATRP of methyl methacrylate in dimethylsulfoxide; acetyl group deprotection under mild conditions. The second pathway allows us to obtain such glycopolymers in only two steps: direct introduction of the same initiator groups onto the dextran chain and subsequent ATRP of methyl methacrylate in dimethylsulfoxide. Throughout the synthesis, detailed studies of each step enabled us to estimate the length of the dextran backbone and to assure the control of copolymer architecture in terms of graft number and graft length. Preliminary interfacial tension measurements highlighted the surfactant properties of such glycopolymers

Ce travail de thèse avait pour objectif d’élaborer un système vecteur ciblantl’endothélium pathologiquement activé dans les tissus enflammés, infectés ou tumoraux.Ce vecteur est sous forme de nanoparticules décorées de ligands glycosides capablesd’interagir avec l’E-sélectine, un récepteur exprimé sur les cellules endothélialesactivées.Nous avons mis au point une synthèse de copolymère amphiphile avec une architectureà bloc muni sur sa partie hydrophile d’un ligand glucidique. Ce copolymère a été par lasuite utilisé pour la préparation de nanoparticules de type coeur/couronne. La partiehydrophobe centrale est entourée d’une couronne hydrophile dont l'encombrementstérique et la mobilité limitent l'opsonisation de la particule. Le ciblage actif a été assurépar la présence d’un ligand du récepteur de l’E-sélectine aux extrémités des chaînes depolymères hydrophiles à la surface du vecteur.Avec ces nanoparticules dont les propriétés de surface sont prédéfinies, nous avonsmontré in vitro l’association efficace avec les cellules endothéliales activées, ce qui apermis de valider ce concept de ciblage moléculaire actif par l’intermédiaire du couplerécepteur/ ligand. Un tel système permettra d’améliorer l’indice thérapeutique et labiodistribution des principes actifs anti-inflammatoire et/ou anticancéreux. / The objective of this work was to develop a delivery system targeting pathologically activated endothelium within inflamed, infectious, and some tumoral tissues. This system is composed of nanoparticles bearing sugar residues that are able to recognize and interact with E-selectin, a receptor expressed on the activated endothelial cells.We synthesized an amphiphilic block copolymer with the hydrophilic part terminated by a carbohydrate ligand. The construction was achieved by a combination of click chemisty, ring-opening polymerization and atom transfer radical polymerization. This copolymer was used to prepare nanoparticles of the core/shell type where the central hydrophobic body is surrounded with the hydrophilic shell that can stabilize the particles in aqueous media and limit their opsonisation. Active targeting was achieved by coupling an analogue of sialyl Lewis X, the physiological ligand of E-selectin to the end of the hydrophilic polymer chains on the surface of the particles.We were able to demonstrate in vitro the efficient association of these nanoparticles with defined surface properties with activated endothelial cells. This allowed us to validate our concept of active molecular targeting using this couple receptor/ligand couple. Such a system could be used to improve the therapeutically index and the biodistribution of anti-inflammatory and anti-tumor drugs.

La biocontamination des surfaces et les risques associés sont des enjeux majeurs économiques et de santé publique. Afin de limiter ou empêcher l’adhésion bactérienne, une des solutions possible consiste en la modification des propriétés des surfaces, afin de leur conférer les fonctions voulues. Dans ce contexte, l’objectif de cette étude est de modifier des surfaces de types métallique (acier) ou polymère : poly(téréphtalate d’éthylène) par des glycomonomères ou des monomères bioactifs. La stratégie de modification des surfaces s’effectue en plusieurs étapes.La première étape permet d’incorporer des fonctions réactives sur les surfaces par traitement acide puis réaction avec la dopamine, ou par traitement plasma ammoniaque. Des fonctions hydroxyle et amine sont introduites. Par la suite un amorceur de polymérisation par transfert d’atome est greffé sur les surfaces. Les monomères sont synthétisés et leur polymérisation étudiée en solution, dans un premier temps dans les conditions de polymérisation radicalaire classique, puis par polymérisation par transfert d’atome. Les conditions optimales sont déterminées, puis les polymérisations sur surfaces effectuées. La dernière étape concerne l’étude des propriétés microbiologiques des surfaces synthétisées.Les glycopolymères protégés et déprotégés de galactose ainsi que les polymères de méthacrylate de gaïacyle et de méthacrylate de thymyle ont été synthétisés. Les monomères ont été polymérisés par polymérisation par transfert d’atome à partir de la surface, sur les surfaces d’acier et de poly(téréphtalate d’éthylène). Après chaque étape de modification de surface, les matériaux ont été systématiquement caractérisés par goniométrie et spectroscopie à photoélectrons X. Les surfaces d’acier fonctionnalisées par le glycopolymère présentent des propriétés anti-adhésives vis-à-vis de Bacillus subtilis, un effet plus marqué est observé après greffage du glycopolymère déprotégé. Les surfaces de poly(téréphtalate d’éthylène) quant à elles, possèdent des propriétés anti-adhésives leur du greffage du poly(méthacrylate de thymyle) vis-à-vis de Listeria monocytogenes, Staphilococcus aureus et Pseudomonas aeruginosa. Un effet anti-biofilm a également été mis en évidence vis-à-vis de Staphilococcus aureus.En parallèle des homopolymères d’ammonium quaternaire et des copolymères obtenus en incorporant les monomères bioactifs ont été synthétisés. Les propriétés antibactériennes sont testées en milieu planctonique vis-à-vis de Bacillus subtilis. Un degré de polymérisation égal à 78 et les groupements halogénoalcane : iodométhane ou bromoéthane permettent l’obtention de la concentration minimale inhibitrice la plus faible. La présence des monomères bioactifs permettent la diminution de la concentration minimale inhibitrice. Le résultat le plus intéressant est obtenu lors de l’incorporation d’un pourcent de N-(4-hydroxy-3-méthoxy-benzyl)-acrylamide. / Bio-contamination of surfaces and related risks are very important economically and for public health. To prevent this phenomenon, one solution is to modify the properties of the surfaces, in order to give them the wanted functionalities. The goal of this study is the modification of metallic surfaces (steel) or polymer surfaces: poly(ethylene terephtalate) with glycomonomers or bioactives monomers. To reach this objective, a multi-step strategy is applied.The first step enabled the incorporation of reactive species on the surfaces by an acid treatment followed by a reaction with dopamine, or by ammonia plasma treatment. Hydroxyl or amine functional groups are added. Then, an initiator of atom transfer radical polymerization is grafted on surfaces. Monomers are synthesized and conventional polymerization and atom transfer radical polymerization are studied. Optimal conditions are determined and polymerization on surfaces achieved. The last step is the study of the microbiological properties of the synthesized surfaces.Protected and unprotected galactose glycopolymers as well as gaiacyl methacrylate and thymyl methacrylate have been synthesized. Monomers have been polymerized by atom transfer radical polymerization directly to the steel or poly(ethylene therephtalate) surfaces. After each step, materials are analyzed by contact angle measurements and X-ray photoelectron spectrometry.Steel surfaces which are functionalized by a glycopolymer and tested in presence of Bacillus subtilis are found to have antiadhesive properties. A most important effect is observed with the unprotected glycopolymer. Poly(ethylene terephtalate) surfaces have antiadhesive properties in presence of Listeria monocytogenes, Staphilococcus aureus and Pseudomonas aeruginosa when poly(thymyl methacrylate) is grafted. An antibiofilm effect is observed with Staphilococcus aureus.Simultaneously, quaternary ammonium homopolymers and copolymers by integration of bioactive monomers have been obtained. Their antibacterial properties are tested in planctonik conditions in presence of Bacillus subtilis. A degree of polymerization equal to 78 and alkyl halide groups: iodomethane and bromoethane enabled to obtain the lowest minimal inhibitory concentration. Bioactive monomers contributed to emphasize this decrease. The most decreasing effect is obtained when one per cent of N-(4-hydroxy-3-méthoxy-benzyl)-acrylamide is integrated.

New water soluble, attainable to ATRP polymerization Cl-terminated poly(glycidol) macroinitiators were prepared by modification of (Omega)-hydroxyl group of poly(glycidol acetal) using 2-chloropropionyl chloride fallowed by selective acidic deprotection of acetal groups. The obtained macroinitiators of different molar masses were successfully employed in ATRP of NIPAM and 4VP to give well-defined stimuli sensitive block copolymers of targeted molar ratio of blocks. The results obtained from light scattering methods showed formation of stable aggregates upon stimuli (pH or temperature) by all the obtained polymers. Additionally, photocrosslinkable block copolymers of glycidol and NIPAM having incorporated moieties of chromophore (2-(dimethyl maleinimido)-N-ethyl-acryl amide) were prepared using macroinitiator technique and used to synthesis of temperature sensitive microgels. Conjunction points have been successfully formed by UV irradiation of polymer water solution above cloud point. The influence of such parameters like block ratio, block length, amount of chromophore, concentration, irradiation time, temperature and heating rate on the properties of obtained microgels was investigated. The obtained core-shell structures were stable under critical conditions and showed continuous volume phase separation process upon increase of temperature, fully reversible and reproducible (no hysteresis effect). Thus, the proposed method not only gave the opportunity to control size or swelling degree of microgels, but also diminished gradient in crosslinking density (random chromophore distribution in polymer backbone), improved colloid stability (poly(glycidol) shell) and completely eliminated additives (surfactants, initiators, stabilizers).

No description available.

L’un des enjeux majeurs en nanomédecine est de développer des systèmes capables à la fois de permettre un diagnostic efficace et également de servir de plateforme thérapeutique pour combattre les infections et les neuro-dégénérescences. Dans cette optique, et afin d’améliorer la détection de tumeurs, des agents de contraste ont été développés dans le but d’augmenter le rapport signal sur bruit. Parmi ces agents, les nanoparticules (NPs) d’oxyde de fer superparamagnétiques (SPIOs) et les quantum dots (QDs) sont des candidats idéaux et ont reçu une grande attention depuis une vingtaine d’années. De surcroit, leurs propriétés spécifiques dues à leurs dimensions nanométriques et leurs formes permettent de moduler leur bio-distribution dans l’organisme. L’opportunité de revêtir ces NPs biocompatibles par des couches de polymères devraient permettre d’améliorer la stabilité de ces nanomatériaux dans l’organisme. Et par conséquent, favoriser leur biodistribution et également leur conférer de nouvelles applications en l’occurrence des applications biomédicales. Dans ce travail de thèse, nous avons développé de nouveaux systèmes thermo-répondant basés sur un cœur SPIOs ou QDs qui sont capables, à la fois, de transporter un principe actif anticancéreux, i.e. la doxorubicine (DOX) et de le relarguer dans le milieu physiologique à une température contrôlée. Deux familles de NPs ont été synthétisées. La première concerne des NPs de Fe3O4 SPIO qui ont été modifiées en surface par un copolymère thermorépondant biocompatible à base de 2-(2-methoxy) méthacrylate d’éthyle (MEO2MA), oligo (éthylène glycol) méthacrylate (OEGMA). La seconde famille, consiste en des NPs de ZnO recouverte du même copolymère. Pour la première fois, le copolymère de type P(MEO2MAX-OEGMA100-X) a été polymérisé par activateur-régénéré par transfert d’électron-polymérisation radicalaire par transfert d’atome (ARGET-ATRP). La polymérisation et copolymérisation ont été initiées à partir de la surface. Les NPs cœur/coquilles ont été caractérisées par microscopie électronique à transmission (TEM), analyse thermogravimétrique (TGA), etc. Nous avons montré que l’efficacité du procédé ARGET-ATRP pour modifier les surfaces des NPs de SiO2, Fe3O4 et de ZnO. L’influence de la configuration de la chaîne de copolymère et des propriétés interfaciales avec le solvant ou le milieu biologique en fonction de la température a été étudiée. Nous avons montré que les propriétés magnétiques des systèmes coeur/coquilles à base de Fe3O4 ne sont influencées que par la quantité de polymère greffée contrairement au QDs qui vient leur propriété optique réduire au-delà de la température de transition. Ce procédé simple et rapide que nous avons développé est efficace pour le greffage de nombreux copolymères à partir de surfaces de chimie différentes. Les expériences de largage et relarguage d’un molécule modèle telle que la DOX ont montré que ces nanosystèmes sont capables de relarguer la DOX à une température bien contrôlée, à la fois dans l’eau que dans des milieux complexes tels que les milieux biologique. De plus, les tests de cytocompatibilité ont montré que les NPs coeur/coquilles ne sont pas cytotoxiques en fonction de leur concentration dans le milieu biologique. A partir de nos résultats, il apparaît que ces nouveaux nanomatériaux pourront être envisagés comme une plateforme prometteuse pour le traitement du cancer / One of the major challenges in nanomedicine is to develop nanoparticulate systems able to serve as efficient diagnostic and/or therapeutic tools against sever diseases, such as infectious or neurodegenerative disorders. To enhance the detection and interpretation contrast agents were developed to increase the signal/noise ratio. Among them, Superparamagnetic Iron Oxide (SPIO) and Quantum Dots (QDs) nanoparticles (NPs) have received a great attention since their development as a liver contrasting agent 20 years ago for the SPIO. Furthermore, their properties, originating from the nanosized dimension and shape, allow different bio-distribution and opportunities beyond the conventional chemical imaging agents. The opportunity to coat those biocompatible NPs by a polymer shell that can ensure a better stability of the materials in the body, enhance their bio-distribution and give them new functionalities. It has appeared then that they are very challenging for medicinal applications. In this work, we have developed new responsive SPIO and QDs based NPs that are able to carry the anticancer drug doxorubicin (DOX) and release it in physiological media and at the physiological temperature. Two families of NPs were synthesized, the first one consist in superparamagnetic Fe3O4 NPs that were functionalized by a biocompatible responsive copolymer based on 2-(2-methoxy) ethyl methacrylate (MEO2MA), oligo (ethylene glycol) methacrylate (OEGMA). The second family consists in the ZnO NPs coated by the same copolymer. For the first time, P(MEO2MAX-OEGMA100-X) was grown by activator regenerated by electron transfer–atom radical polymerization (ARGET-ATRP) from the NPs surfaces by surface-initiated polymerization. The core/shell NPs were fully characterized by the combination of transmission electron microscopy (TEM), thermogravimetric analysis (TGA), and by the physical properties of the nanostructures studied. We demonstrate the efficiency of the ARGET-ATRP process to graft polymers and copolymers at the surface of Fe3O4 and ZnO NPs. The influence of the polymer chain configuration (which leads to the aggregation of the NPs above the collapse temperature of the copolymer (LCST)) was studied. We have demonstrated that the magnetic properties of the core/shell Fe3O4-based nanostructures were only influenced by the amount of the grafted polymer and no influence of the aggregation was evidenced. This simple and fast developed process is efficient for the grafting of various co-polymers from any surfaces and the derived nanostructured materials display the combination of the physical properties of the core and the macromolecular behavior of the shell. The drug release experiments confirmed that DOX was largely released above the co-polymer LCST. Moreover, the cytocompatibility test showed that those developed NPs do not display any cytotoxicity depending on their concentration in physiological media. From the results obtained, it can be concluded that the new nanomaterials developed can be considered for further use as multi-modal cancer therapy tools

Ce travail de thèse vise à concevoir de nouvelles membranes performantes pour la séparation de gaz (CO2) dans le procédé de post-combustion. La stratégie proposée repose sur la préparation de membranes hybrides organiques/inorganiques, combinant des supports poreux de dioxyde de titane (TiO2) intégrés dans une couche dense de polymère à base de poly-oxyde d'éthylène. L'un des points important de cette étude est l'ancrage de la phase organique sur le support inorganique. Deux agents de couplage : le propyl phosphonique acide 2-bromo-2-méthyl propanoate et le 3--propylamino triéthoxy silan ont été sélectionnés et greffés sur trois surface de TiO2 différentes : des nanoparticules, des surfaces denses et des surfaces poreuses. Pour chacune des deux molécules d'ancrage les meilleurs résultats ont été obtenus avec les nanoparticules. Les nanoparticules de TiO2 ainsi fonctionnalisées, ont dans une seconde étape, servi de semences pour l'élaboration de particules coeur-écorce. Deux voies de polymérisation ont été explorées avec succès : la si-ATRP et la si-ROMP. Dans le premier cas des greffons de poly-poly-éthylène glycol méthyl éther méthacrylate ont été introduits sur les nanoparticules de TiO2. Pour la si-ROMP les greffons incorporés sont à base de polynorbonène. Les résultats obtenus sur les nanoparticules de TiO2 ont été exploités afin de créer des couches polymères sur des supports poreux céramiques tubulaires commerciaux. Deux modes de conception ont été développés : la voie dite "coating onto" et celle dite "Grafting from". Les membranes composites obtenues par ces deux voies ont été testées en perméabilité des gaz afin de déterminer la qualité des couches polymères. Des essais préliminaires de séparation des gaz ont été également effectués. / This thesis work aims towards designing hybrid membranes for CO2 separation in the post-combustion process. The different methods of existing technologies are compared ans assessed for their merit, and the decision of using inorganic titanium dioxide supports integrated with a grown polymeric/PEG layer is made. First, the structure of the interfacing group is determined and narrowed down to phosphonic-based anchoring groups. The modification of various titanium oxide surfaces (i.e. particle, flat and porous) is performed with each group, and particles were found to yield the highest surface modification. Secondly, the functionalized particles of titania were then studied for their potential with si-ATRP and si-ROMP. in the case of phosphonic acid functionalized titania, the particles yielded a bromine terminus that could be used for si-ATPR. In the case of the silane grafted titania particles, further fonctionalization was required to ultimately yield a norbornenyl group that can be used for Si-ROMP. Both teechniques were shown to work, and were thus applied to longer ceramic tubes. Finally the development of two pathways ("Coating onto" and "Grafting from") were assessed for their ability to modify the tubular ceramic support and preliminary gas separation tests were performed.

New water soluble, attainable to ATRP polymerization Cl-terminated poly(glycidol) macroinitiators were prepared by modification of (Omega)-hydroxyl group of poly(glycidol acetal) using 2-chloropropionyl chloride fallowed by selective acidic deprotection of acetal groups. The obtained macroinitiators of different molar masses were successfully employed in ATRP of NIPAM and 4VP to give well-defined stimuli sensitive block copolymers of targeted molar ratio of blocks. The results obtained from light scattering methods showed formation of stable aggregates upon stimuli (pH or temperature) by all the obtained polymers. Additionally, photocrosslinkable block copolymers of glycidol and NIPAM having incorporated moieties of chromophore (2-(dimethyl maleinimido)-N-ethyl-acryl amide) were prepared using macroinitiator technique and used to synthesis of temperature sensitive microgels. Conjunction points have been successfully formed by UV irradiation of polymer water solution above cloud point. The influence of such parameters like block ratio, block length, amount of chromophore, concentration, irradiation time, temperature and heating rate on the properties of obtained microgels was investigated. The obtained core-shell structures were stable under critical conditions and showed continuous volume phase separation process upon increase of temperature, fully reversible and reproducible (no hysteresis effect). Thus, the proposed method not only gave the opportunity to control size or swelling degree of microgels, but also diminished gradient in crosslinking density (random chromophore distribution in polymer backbone), improved colloid stability (poly(glycidol) shell) and completely eliminated additives (surfactants, initiators, stabilizers).

Multifunctional monomers on the basis of acryl- and methacryl derivatives were synthesized and different protective groups were used. After polymerization the protective groups were removed by different methods. Various initiators for the NMP of the monomers were synthesized and the reaction conditions were optimized. The results showed that NMP was not a suitable method for multifunctional acryl- and methacryl derivatives to achieve well-defined homopolymers, although it was successful for control of polymerization of styrene and block copolymerization of multifunctional acryl- and methacryl derivatives with alkoxyamine terminated polystyrene. The ATRP of multifunctional acrylates and methacrylates has been successfully performed, as well as the block copolymerization of multifunctional acrylates and methacrylates. Relatively low polydispersities of the corresponding polymers (PD=1.18-1.36) and reasonably high rates of polymerization could be achieved when Me6TREN and PMDETA were used as ligands. However, the ATRP of multifunctional acrylamides and methacrylamides failed. The RAFT-polymerization of styrene, acrylamide and acrylate using BDTB as a CTA and AIBN as an initiator afforded polymers with narrow molecular weight distribution (PD=1.13-1.26). A kinetic investigation and the further synthesis of block copolymers using dithioester-terminated homopolymers as macroCTAs showed that the RAFT polymerization of acrylamide M9b proceeded in a living manner. However, BDTB does not control the reaction of methacrylic monomers, such as methacrylates and methacrylamides. The bulk phase behavior of the block copolymers were examined by means of DSC and the surface behaviors of block copolymers as thin layers were examined with AFM. Two-phase transitions in the block copolymers were observed clearly by DSC, indicative of the appearance of phase separations, which were seen in an AFM image. In conclusion, multifunctional acryl- and methacryl derivatives failed to achieve well-defined homopolymers by NMP. However, this method was successful for block copolymerization of multifunctional acryl- and methacryl derivatives with alkoxyamine terminated polystyrene. Multifunctional acrylates and methacrylates were successfully homopolymerized and block copolymerized by ATRP. Multifunctional acrylates and acrylamides were suitable for homopolymerization and block copolymerization by the RAFT process. Thus far, it is difficult to homopolymerize multifunctional methacrylamides in controlled way.

Controlled radical polymerization (CRP) can be viewed as the middle ground between living anionic polymerization (LAP) and conventional free radical polymerization (FRP). It combines the precise control over polymer structure offered by LAP, under a tolerant reaction condition similar to FRP. One of the most studied CRP is atom transfer radical polymerization (ATRP), with over 10,000 papers published since its introduction in 1995. Despite the numerous studies, knowledge on its fundamental mechanism is still lacking, as evident from the lack of expression for full MWD and polydispersity that account for termination reaction. Since termination is unavoidable in ATRP, the existing expressions give inaccurate predictions as dead chains accumulate. In this study, we derived expressions for full MWD at low conversion and for polydispersity. These expressions allow us to quantify and gain better understanding on the contribution of termination. In addition, the resulting polydispersity expression shows better agreement than the existing equation when correlated with experiment data. In addition to the aforementioned questions, there are also controversies regarding the kinetics of surface-initiated ATRP, with researchers divided into two schools of theories. We evaluated the validity of these theories by comparing their predictions to experimental trends. Both theories were found to be inadequate in explaining all the experimental observations, thus triggering an investigation of the graft density. Graft density is an important determining property for polymer brushes, yet little is known about what affects its final value. Through simulations, we investigated the effect of experiment factors on the grafting density. A decrease in the amount of deactivator is found to decrease the grafting density, which could be explained by an increase in the number of monomers added per activation cycle. This knowledge allows us to explain the conflicting experiment observations regarding the growth trends of polymer layers reported in the literatures. / Thesis / Doctor of Philosophy (PhD) / Polymer materials are used almost everywhere in our daily life from clothing to water bottle. This wide range of applications owes to the nearly infinite possible properties that polymer can possess. Different polymerization processes to synthesize polymers have their own weaknesses and strengths. Herein we investigated the fundamental mechanism of one of the currently most attractive polymerization systems, atom transfer radical polymerization (ATRP). This process allows the synthesis of polymers with precisely tailored chain microstructures, making it possible to create polymer with sophisticated properties. Using modeling approaches, we derived explicit expressions for determining chain properties, allowing detailed investigation of how various factors affect these properties. Through these investigations, we obtained better understanding on the mechanism of ATRP in solution and on surface. This knowledge is crucial in providing insight and guiding experimental designs for better control over the material properties.