Machining of Aluminum can be complicated due to large amounts of adhesion and diffusion of the aluminum onto the cutting tool, causing effects such as built-up layers and built-up edges. This leads to poor surface finishes and can significantly affect the tool life. CVD diamond coated tools have shown to be a potential solution to this problem and is tested and analyzed as such in this thesis. CVD diamond coated inserts are tested and compared to uncoated cemented carbide inserts and Polycrystalline diamond tipped inserts, in milling, turning and in refined tribological methods. The workpiece material in both the machine tests and the tribological tests is a high strength aluminum of the name Alumec 89. The machine tests were performed for 5 and 60 seconds at three cutting speeds, 600, 900 and 1200 m/min, keeping other parameters constant. The cutting inserts, the chips and the generated workpiece surface are examined using LOM, SEM and EDS. In the refined tribological testing, a pin-turning tribometer is used, with pins of uncoated and coated (CVD diamond) cemented carbide pins. These are tested at 5 and 30 seconds at 600 and 1200 m/min, applying a constant force of 10 N. In addition, a friction test was performed to measure the friction of the uncoated and the CVD diamond coated cemented carbide. Like the cutting inserts, the used pins were examined in LOM and SEM. The results show that while a large amount of built-up layer and built-up edges gather when using uncoated cemented carbide tools, only minimal amounts can be detected on CVD diamond and PCD. It has also been shown that the reason for the reduced adhesion in the case of diamond tooling materials is most likely due to the lack of chemical interactions between the diamond and the aluminum. The friction of the CVD diamond material was shown to be lower compared to the cemented carbide. The surface finish generated by the different materials, was the best in the case of PCD while the CVD generated multiple small scratches that severely reduced the surface roughness. This thesis provides some initial basic understanding of the interaction of CVD diamond coated inserts with high strength aluminum alloys.

Fräsning och annan intermittent skärande bearbetning ger upphov till termisk utmattning av skärverktyg. Problemet med termiska sprickor blir större vid bearbetning av värmehållfasta material som austenitiskt rostfritt stål eftersom värmeväxlingarna i skärverktyget blir mer extrema. Detta fenomen förvärras ytterligare vid användning av traditionell kylning. Fräsning av rostfritt stål utförs därför torrt. Den torra bearbetningen är inte oproblematisk eftersom höga temperaturer uppstår i skärzonen vilket påverkar verktygets livslängd och i vilken utsträckning avverkningshastigheten kan höjas med högre skärhastighet eller matning. Detaljer som tar lång tid att tillverka är negativt för både företagens ekonomi och miljön till följd av större energiåtgång.Minimalsmörjning är en metod som går ut på att små mängder smörjmedel i form av aerosol fokuseras mot skäreggen och smörjer kontakten mellan arbetsstycke och skär, vilket minimerar friktionsvärmen. På detta sätt kan den totala värmeutvecklingen reduceras samtidigt som värmeväxlingarna hålls på en lägre nivå jämfört med traditionell kylning. Syftet med arbetet var att undersöka och jämföra planfräsning av austenitiskt rostfritt stål, 1.4301, under torr bearbetning och bearbetning med minimalsmörjning.Centralt för studien var hur verktygsförslitningen och ytjämnheten hos bearbetat material påverkas då minimalsmörjning appliceras gentemot vid torr bearbetning.En fråga som togs upp var om avverkningshastigheten kunde ökas med minimalsmörjning utan att få negativ inverkan på verktygsförslitning och ytjämnhet av bearbetat arbetsstycke.Fullfaktorförsök upprättades och jämförelsen mellan torr bearbetning ochminimalsmörjning gjordes med planfräsning med PVD-belagda hårdmetallskär. Ett optiskt mätmikroskop användes för att analysera förslitningen på skärverktygens spån- och släppningssidor efter ca 3 minuter i ingrepp. Ytjämnhet på bearbetad ytamättes med ytjämnhetsmätare och temperaturen i arbetsstycket mättes med termoelement.Resultatet visade att tillämpning av minimalsmörjning sänker temperaturen i skärzonen vilket för rostfritt stål innebär att skärhastigheten bör ökas för att undvika löseggsområdet. På så sätt ökar även avverkningshastigheten och produktiviteten. / Milling and other intermittent metal cutting operations often cause thermal fatigue in the cutting tools used. This type of wear is more severe during machining of heat resistant alloys such as austenitic stainless steel because of more extreme temperature variations during the cutting procedure. This phenomenon is further accelerated by employing flood cooling. Milling of stainless steel is therefore usually performed dry. Dry cutting is, however, not without its share of problems, since high temperatures develop in the cutting zone which adversely affect tool life and to which extent the productivity can be increased via higher cutting speeds or feed rates. Parts that take longer to manufacture are not only bad for business economics, but also for the environment due to higher energy consumption.Minimum quantity lubrication is a method that uses minimal quantities of oil dispersed as aerosol toward the cutting edge. This lubricates the tool-workpiece interface which minimizes frictional heat. This way, the total heat during cutting can be reduced while also avoiding the extreme temperature variations associated with flood cooling. The purpose of this thesis is to study and compare the performance of dry cutting and minimum quantity lubrication during face milling of austenitic stainless steel, 1.4301.The tool wear rates of the cutting tools and surface quality of the machined workpiece were compared for the two cutting environments. Of particular interest was the question whether the material removal rate could be increased with the usage of minimum quantity lubrication without adversely impacting the tool life or workpiece surface quality.A full factorial design of experiments was created, and the comparison of dry machining and minimum quantity lubrication was done by face milling with PVDcoated carbide inserts. An optical stereo microscope was used for the analysis of rake and flank wear after roughly 3 minutes of cutting tool engagement. Surface roughness of machined part was measured with a measuring stylus, and the temperature of the workpiece was measured with embedded thermocouples.The results show that minimum quantity lubrication reduces the temperature in the cutting zone, which for stainless steel means that the cutting speed should be increased to avoid the formation of built-up edges. At the same time, the material removal rate is increased, and productivity is affected positively.

Internal Combustion Engine (ICE) exhaust components are exposed to extreme operating temperatures. Thus, it is necessary that they are designed with materials that can sustain thermal and vibrational stresses. This study investigates the wear mechanisms and tribological performance of the exhaust manifold joint in Scania CV diesel trucks, focusing on the lip seal ring between the exhaust and turbo manifolds. The joint is prone to wear due to thermal and vibrational stresses, impacting its service life and raising environmental concerns. The manifold material, ductile cast iron SiMo51, offers good thermal resistance, while the lip seal ring, made of Inconel 718c, provides excellent thermal fatigue and corrosion resistance, coated with AlTiN for wear and oxidation resistance. However, the tribological performance of this joint and material combination remains unknown, necessitating further research.  This work aims to understand wear initiation mechanisms and their relationship with temperature. Test setups were established using an oscillating cylinder on disc configuration in the SRV 3 tribometer. SiMo51 uncoated/coated with Tribaloy 400 and Inconel 718c uncoated/coated with AlTiN were tested against each other to identify the best material pair. Analysis involved coefficient of friction, visual inspection, wear volume measurements, SEM micrographs, and EDS for surface chemical composition. Results indicated that friction behaviour is temperature-dependent, with oxide layer formation reducing the coefficient of friction when the manifold is uncoated, while the opposite occurs when coated with Tribaloy 400. Wear behaviour varied based on material combinations and temperature. Uncoated manifold exhibited dominant adhesion (galling) accompanied by tribo-oxidation at higher temperatures, with maximum wear volumes at room temperature. Introduction of T-400 on the manifold initiated galling on the lip seal, leading to abrasion on the manifold surface, accompanied by tribo-oxidation at elevated temperatures. Wear increased until 500°C, followed by a decrease at 700°C. Further explanations of T-400 wear behaviour are lacking in the literature.

The transition to a Circular Economy scheme that enables a more efficient usage of the resources is one of the most pressing needs in our society. From the industrial perspective this has been translated into new design philosophies and the search for more efficient systems. Polymeric composites have played a key role in the development of lighter components with good mechanical and tribological properties. Specifically, the demand of Carbon Fiber Reinforced Polymers (CFRP) has had an increasing trend since 1970s-1980s, becoming one of the kind of composites with the highest demand in the market to supply industries such as aerospace, automotive, construction, renewable energies, among others. With the increasing demand of CFRP materials some of the main challenges that arise are their disposal, environmental impact and cost of production to maintain the required supply. The use of Carbon Fibers as a reinforcement for polymeric matrices has been widely documented over the last decades, however the characterization of recycled Carbon Fibers for tribological applications is still scarce. Therefore, this investigation is focused on the mechanical and tribological characterization under water lubricated conditions of Ultra High Molecular Weight Polyethylene (UHMWPE) composites reinforced with virgin and recycled Carbon Fibers and Graphene Oxide. The findings of this work provide an important panorama regarding the performance of recycled Carbon Fibers, showing that they can have a comparable performance in mechanical properties and tribological behavior. This enables the use of recycled Carbon Fibers without compromising performance while reducing the environmental impact and cost.

The possible use of graphene and its derivatives dissolved in water as a green lubricant is an interesting avenue of research from tribological perspective. In this study, a highly concentrated stock solution of aqueous Graphene employing Polyethylene Glycol(PEG) as surfactant was diluted using proportionate volumes of De-Ionized (D.I.) water to generate target concentrations of Graphene in solution ranging from 15 μg/ml to 350 μg/ml . These samples were then tested for both sliding and rolling contacts. The sliding contact tests included the use of both 4-ball Tribometer test rig and triborheometer. The rolling contact tests were performed on Mini Traction Machine. The tested graphene-PEG-water admixtures held significant friction and wear advantage over D.I. Water and surfactant solutions under the same testing conditions. / Den möjliga användningen av grafen och dess derivat upplöst i vatten som ett grönt smörjmedel är en intressant forskningsaveny ur ett tribologiskt perspektiv. I denna studie späddes en högkoncentrerad grafenlösning med av-joniserat (D.I.) vatten för att alstra mållösningskoncentrationer av greven mellan 15 μg/ml och 350 μg/ml. Den testade grafenlösningen hade polyetylenglykol som ytaktivt ämne Proven testades sedan för både glidande och rullande kontakter. De glidande kontakttesten innefattade användandet av både en 4-kuletribometer och en triborometer. De rullande kontakttesterna utfördes med en Mini-traktionsmaskin. De testade proverna uppvisade signifikanta friktions- och förslitningsfördel jämfört med D.I. vatten och ytaktiva lösningar under samma testförhållanden

There has been much discussion about the beneficial uses of lamellar graphite iron in piston rings–cylinder liner systems, where a good combinations of both thermal and tribological properties are essential. The excellent tribological performance of lamellar iron under such sliding conditions is principally associated with lubrication behaviour of the graphite particles which are distributed as lamellas throughout the matrix. During sliding, graphite particles are extruded and smeared onto the counterfaces, act as solid lubricating agents and form a thin graphite film between the sliding surfaces. Although this process especially, during the running-in period significantly changes the sliding wear response of the components, the exact mechanism behind of this phenomenon has rarely been discussed in previous studies. It is tribologically beneficial to keep the graphite open, particularly in applications where the scuffing issues do matter. In this thesis, the main causes involved in closing the graphite lamellas are discussed, with a focus on matrix plastic deformation that occurs during sliding. In first step, the relationship between graphite lamellae orientation and plastic deformation was investigated. To do so, two piston rings, belonging to the same two-stroke marine engine operated for different periods of time, were selected and compared to the unworn sample. The worn piston rings displayed a substantial decrease in both frequency and area fraction of the graphite lamellas. Most of the lamellas were closed as a result of plastic deformation of matrix. This happening was caused mainly by the interaction between abrasive particles and metallic matrix. Additionally, it was found that graphite lamellas parallel or near-parallel to the sliding direction exhibited maximum closing tendency under sliding condition. In next step, to have a better understanding of the graphite film formation mechanism and matrix deformation role in closing the graphite lamellas, microindentation and microscratch testing were performed on typical lamellar iron. The qualitative results showed a similar mechanism involving in graphite contribution to lubricate the sliding surfaces. Moreover, microindentations made nearby the graphite lamellas demonstrated that the deformation of the matrix causes the formation of cracks in the centre of the graphite lamellas, compressing and then extruding the graphite from its natural position, irrespective of the lamellas′ size. Furthermore, it was found that subsurface graphite orientation had a large influence on the extrusion behaviour, in that, for graphite lamellas oriented towards the indenter, the effect was observed more pronounced. Furthermore, an improved fully ferritic solution strengthened compacted graphite iron was produced for future wear studies. The effects of different Si levels and section thicknesses on tensile properties and hardness were investigated as well. The influence of Si content and section thickness on mechanical properties was revealed by improving the materials strength and slightly enhancing the hardness through increasing Si content. Besides, Si addition up to 4.5 wt% significantly affected the strength and elongation to failure of cast samples. / Helios / FFI

[ES] En la actualidad, el ambito del transporte mediante el uso de vehículo ligero sufre un gran cambio hacia la descarbonización. Cada vez más, las autoridades europeas restrigen las emisiones de gases de efectos invernaderos hacia la atmósfera emitidos por estos vehículos. Soluciones alternativas a la propulsión con energía fósil, como la implementación de vehículos eléctricos o híbridos, no está lo suficientemente desarrollada para sustituir a los motores de combustión interna alternativos (MCIA), debido a su todavía alto coste de producción y baja infrastructura para abastecer la demanda de energ ́ıa eléctrica. En este contexto, la transición hacia una movilidad sostenible y renovable sigue pasando por el aumento de la eficiencia y la reducción del consumo de combustible en motores de combustión interna. Una alternativa a la mejora de la eficiencia es la reducción de las pérdidas mecánicas por fricción, o en otras palabras, optimización de la tribología. La tribología en un MCIA lleva asociada aspectos mecánicos como la optimización de los acabados superficiales de los distintos componentes que conforman el motor y la optimización de propiedades física, químicas y reológicas del aceite que lo compone. Esta última solución presenta un alto ratio beneficio/coste, ya que su implementación no lleva asociada ninguna modificiación en el hardware y su implementación es directa. Uno de los objetivos de la Tesis Doctoral, es desarrollar un modelo 1D que contenga la información tribológica de un motor de combustión interna que no se puede obtener experimentalmente, que contribuya al entendimiento y optimización de las pérdidas mecánicas por fricción y que ahorre el coste experimental asociado a entender la tribología desde el punto de vista empírico. Estos parámetros van desde el espesor de película de aceite entre los componentes de un par rozante hasta la contribucción a la fricción de las componentes hidrodinámicas y de asperezas de cada elemento rozante. Adem ́as, se ha desarrollado un modelo cuasi estacionario para cuantificar la energ ́ıa disipada por fricción en un ciclo de conducción real y el consumo de combustible asociado al mismo. As ́ı pues, a través de este modelo, se implementan soluciones que pasan desde aceites optimizados reológicamente hasta acabados superficiales de baja rugosidad, entendiendo la fenomenología asociada a cada tecnología y aportando parámetros claves para la optimización de dicha solución. Finalmente, se estima el ahorro en términos de consumo de combustible que se puede alcanzar con estas soluciones implementadas mediante el modelo cuasi estacionario en condiciones de conducción real / [EN] Currently, the field of light-duty vehicle transport is undergoing a major shift towards decarbonisation. Increasingly, European authorities are restricting emissions of greenhouse gases into the atmosphere from these vehicles. Alternative solutions to fossil fuel propulsion, such as the implementation of electric or hybrid vehicles, are not sufficiently developed to replace internal combustion engine alternatives (ICEs), due to their still high production cost and low infrastructure to meet the demand for electric power. In this context, the transition towards sustainable and renewable mobility continues to be based on increasing efficiency and reducing fuel consumption in internal combustion engines. An alternative to improving efficiency is the reduction of mechanical frictional losses, or in other words, optimisation of tribology. Tribology in an MCIA is associated with mechanical aspects such as the optimisation of the surface finishes of the different components that make up the engine and the optimisation of the physical, chemical and rheological properties of the oil that makes up the engine. This last solution presents a high benefit/cost ratio, as its implementation does not involve any hardware modification and its implementation is straightforward. One of the objectives of the Doctoral Thesis is to develop a 1D model that contains the tribological information of an internal combustion engine that cannot be obtained experimentally, which contributes to the understanding and optimisation of mechanical friction losses and saves the experimental cost associated with understanding tribology from an empirical point of view. These parameters range from the oil film thickness between two tribological components to the contribution to friction of the hydrodynamic and roughness components of each friction element. In addition, a quasi-stationary model has been developed to quantify the energy dissipated by friction in a real driving cycle and the associated fuel consumption. Thus, through this model, solutions ranging from rheologically optimised oils to low roughness surface finishes are implemented, understanding the phenomenology associated with each technology and providing key parameters for the optimisation of the solution. Finally, the savings in terms of fuel consumption that can be achieved with these solutions implemented using the quasi-stationary model in real driving conditions are estimated. / [CA] Actualment, l’àmbit del transport mitjan ̧cant l’us de vehicles lleugers pateix un gran canvi cap a la descarbonització. Cada vegada m ́es, les autoritats europees restringeixen les emissions de gasos d’efecte hivernacle cap a l’atmosfera emesos per aquests vehicles. Les solucions alternatives a la propulsió amb energia fòssil, com la implementació de vehicles elèctrics o híbrids, no està prou desenvolupada per substituir els motors de combustió interna alternatius (MCIA), a causa del seu encara alt cost de producció i baixa infraestructura per abastir la demanda d’energia elèctrica. En aquest context, la transició cap a una mobilitat sostenible i renovable continua passant per l’augment de l’eficiència i la reducció del consum de combustible en motors de combustió interna. Una alternativa per a la millora de l’eficiència es la reducció de les pèrdues mecàniques per fricció, o en altres paraules, la optimització del comportament tribològic del motor. La tribologia en un MCIA porta associada aspectes mecànics com ara l’optimització dels acabats superficials dels diferents components que conformen el motor i l’optimització de propietats física, químiques i reològiques de l’oli que va a emprar. Aquesta ́ultima solució presenta una alta ratio benefici/cost, ja que la seva implementació no porta associada cap modificació de la màquina i la seva implementació ́es directa. Un dels objectius de la Tesi Doctoral es desenvolupar un model 1D que permet obtindré la informació tribològica d’un motor de combustió interna que no es pot obtenir experimentalment, que contribueixi a l’enteniment i l’optimització de les pèrdues mecàniques per fricció i que estalvi ̈ı el cost experimental associat a entendre la tribologia des del punt de vista empíric. Aquests paràmetres van des de l’espessor de pel·lícula d’oli entre els components d’un parell tribològic fins a la contribució a la fricció dels components amb regim hidrodinàmic i de la rugositat de cada element. A més, s’ha desenvolupat un model gairebé estacionari per quantificar l’energia dissipada per fricció en un cicle de conducció real i el consum de combustible associat. Així, a traves d’aquest model, s’implementen solucions que passen des d’olis optimitzats reològicament fins a acabats superficials de baixa rugositat, entenent la fenomenologia associada a cada tecnologia i aportant paràmetres clau per optimitzar aquesta solució. Finalment, s’estima l’estalvi en termes de consum de combustible que es pot assolir amb aquestes solucions implementades mitjan ̧cant el model quasi estacionari en condicions de conducció real. / Agradezco al programa de Formación de Profesorado Universitario del Ministerio de Ciencia, Innovación y Universidades por soportar financieramiente mis estudios doctorales (FPU18/02116) y la estancia de investigación que contribuyó a aumentar los conocimientos desarrollados en la presente tesis doctoral (EST21/00451). / Jiménez Reyes, AJ. (2022). Assessment and Optimization of Friction Losses and Mechanical Efficiency in Internal Combustion Engines [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/188986

There are two main goals of this thesis. Firstly, to improve and develop an existing hot weartester at Karlstad University so that it may test more samples of different sizes. Secondly, totest previously impossible samples and investigate their tribological properties and measurethe coefficient of friction with high reproducibility. The development work on the tribometer wasdone by a prestudy including; Investigating the hot wear tester, idea generation in CAD andcollecting information from the creator and prior users of it. After a few rounds of conceptgeneration and discussion with the supervisor and workshop staff, a new sample holder withdifferent sample adapters was created. Five tests of four different materials were conductedand their friction was measured. The new sample holder was able to solve the mainconcerns with the old design and showed great promise in producing reproducible results,better than any previous versions. The friction of the different TiAlN samples, at roomtemperature, seemed to indicate that there is a certain amount of Al% that maximizes frictionand that there is no simple linear relationship between Al% and coefficient of friction. Finallyit can be concluded that the initial goals of the thesis have been met, and that a newscientific instrument has been created to aid in the further understanding of tribology. / Det finns två huvudsakliga mål med detta examensarbete. För det första, att förbättra ochutveckla en existerande varmnötare på Karlstad Universitet så att den kan testa fler proverav olika storlekar. För det andra, att testa tidigare omöjliga prov och undersöka derastribologiska egenskaper och mäta friktionskoefficienten med hög reproducerbarhet.Utvecklingsarbetet av tribometern skedde via en förstudie som innehöll följande:Undersökning av varmnötaren, idégenerering i CAD och samling av information frånvarmnötarens skapare, samt tidigare användare. Efter några iterationer avkonceptgenerering och diskussioner med handledare och verkstadspersonal så skapadesen ny provhållare med flera olika adaptrar. Fem tester med fyra olika material utfördes ochderas friktion mättes. Den nya provhållaren löste de huvudsakliga problemen med dengamla designen och påvisade goda förhoppningar angående att producera tester med högreproducerbarhet. Markant bättre än tidigare versioner. Friktionsmätningarna från de olikaTiAlN-proverna, vid rumstemperatur, indikerade att det finns en viss mängd Al% sommaximerar friktionen och att det inte finns något linjärt samband mellan Al% ochfriktionskoefficient. Slutligen kan det konstateras att de initiala målen för examensarbetet harblivit uppnådda, och att ett nytt vetenskapligt instrument har blivit skapat för att hjälpa utökaförståelse inom tribologi.

Grease is among the most widely used lubricants in rolling element bearings. Proper understanding of the effect of lubrication due to grease aging can provide a significant increase in the life of the engineering systems. However, at present, there is no sufficient understanding of the grease aging effect in rolling elements bearing. This restricts the optimal usage of the bearing and timely monitoring of the grease. The current research work tries to address this issue with an experimental investigation. This project studies the behavior of 4 types of greases in rolling elements bearings for various operating conditions by recording the temperature and acoustic emission data. The aged samples were prepared to keep in the oven at 150 °C for a series of time duration letting it go through the chemical changes and thermal degradation. Tests were carried out in a test rig with the different levels of oxidized greases for 5 hrs time. And the effects in bearing temperature, acoustic emission were recorded. This is an investigation to analyze the effects of grease composition and aging in rolling elements lubrication by means of acoustic emission and bearing temperature. The IR spectroscopy was carried from the samples collected from the oven in order to understand the change in lubricant composition. The results show that the grease with di-urea thickener and base oil of synthetic ether and polyolester gives the best bearing temperature and acoustic emission behavior compared to the other grease type. The possibility of using the acoustic emission and temperature data to monitor the grease aging is also presented. Along with this, the possibility of using the AE statistical methods, AE count method, and energy plot were also explored to relate with the degree of aging.

<p>Positive displacement machines (PDMs) operate based on the principle of positive displacement, which necessitates a periodic alteration of volume. This volume variation is accomplished through relative motion between machine components. PDMs find extensive applications in diverse domains, encompassing fluid power systems, lubrication systems, fluid transport systems, fuel injection systems, and more. The primary distinction among PDMs lies in the geometric mechanisms employed for fluid displacement, as well as the flow distribution mechanisms they employ. PDMs can be broadly classified into piston machines, vane machines, screw machines, and gear machines. In fluid power systems, the most commonly used PDMs are the piston and gear machines. Piston machines can be further classified into radial piston machines, in-line piston machines, and axial piston machines. The most commonly used piston machines are the axial piston machine owing to their superior efficiency and compactness. Gear machines can be further classified into external gear machines, internal gear machines, and annular gear machines. The most commonly used gear machine is the external gear machine owing to its price.</p> <p><br></p> <p>PDMs typically involve multiple solid bodies in relative motion, with micron-level gaps between them. These gaps, known as lubricating interfaces, present a significant design challenge during the machine development process. They are a primary source of power losses and play a crucial role in determining the efficiency and durability of the machine. The lubricating interfaces must effectively balance loads and maintain a high-pressure fluid seal. Achieving this delicate balance necessitates a comprehensive understanding of the underlying physical phenomena. Lubricating interfaces generate substantial heat due to viscous dissipation, which directly impacts the operation of the entire machine. The viscosity of the working fluid rapidly decays with temperature, causing the warmer fluid within the lubricating interface to possess lower viscosity. Consequently, it can support lesser loads and is more prone to leakage. Moreover, as the solid bodies enclosing the warmer fluid heat up, they undergo thermal expansion, further changing the clearance and leading to a decline in performance. Additionally, the elevated temperature of the fluid within the lubricating interface affects the compressibility of the displacement chamber fluid, thereby influencing the pressurization characteristics of the entire unit. Thus, thermal effects play a critical role in the performance of PDMs.</p> <p><br></p> <p>  The ever-increasing market demand for more compact, efficient, and reliable designs requires a continuous process of design improvements over previous designs, and sometimes completely new designs. Sophisticated simulation tools are a necessity for such a design process. Additionally, these simulation tools also prove to be valuable in formulating design modifications in case of underperforming designs. Due to the complexity associated with the operation of such units, the simulation tools need to capture a wide variety of physical phenomena. Over the past few decades, owing to the increasing computing power of the desktop computer, several simulation tools have been proposed across the literature to aid the design process of such machines with each having limitations of their own.</p> <p><br></p> <p>  The objective of the present thesis is to propose a modeling approach that assists in the design process of positive displacement machines, addressing various limitations identified in the existing literature. The approach is intentionally designed to be generic, enabling its application across a diverse range of positive displacement machines. The modeling approach encompasses three distinct domains: the displacement chamber fluid domain, the lubricating interface fluid domain, and the solid domain. A novel thermal model that integrates all three domains is introduced. </p> <p><br></p> <p>  To validate the effectiveness of the proposed modeling approach, two separate validation studies are conducted. The first study focuses on a model for an isolated piston/cylinder interface of an axial piston machine, operating under the mixed lubrication regime. The model demonstrates a strong agreement with the measured data. The second study involves steady-state measurements of an entire axial piston machine. The model is validated by comparing the steady-state flow characteristics and temperature distribution on the valveplate, both of which are accurately captured by a single fully coupled model. The modeling approach developed in this study, specifically, the energy conservation in the lubricating interface, heat transfer in the solid bodies, and thermal deformation in the solid bodies are all generalized for applicability in different types of PDMs. However, the results presented in this thesis pertain to an axial piston machine.</p>