A prototype 3-dimensional (3D) anode, based on multiwall carbon nanotubes (MWCNTs), for Li-ion batteries (LIBs), with potential use in Electric Vehicles (EVs) was investigated. The unique 3D design of the anode allowed much higher areal mass density of MWCNTs as active materials, resulting in more amount of Li+ ion intake, compared to that of a conventional 2D counterpart. Furthermore, 3D amorphous Si/MWCNTs hybrid structure offered enhancement in electrochemical response (specific capacity 549 mAhg-1). Also, an anode stack was fabricated to further increase the areal or volumetric mass density of MWCNTs. An areal mass density of the anode stack 34.9 mg/cm2 was attained, which is 1,342% higher than the value for a single layer 2.6 mg/cm2. Furthermore, the binder-assisted and hot-pressed anode stack yielded the average reversible, stable gravimetric and volumetric specific capacities of 213 mAhg-1 and 265 mAh/cm3, respectively (at 0.5C). Moreover, a large-scale patterned novel flexible 3D MWCNTs-graphene-polyethylene terephthalate (PET) anode structure was prepared. It generated a reversible specific capacity of 153 mAhg-1 at 0.17C and cycling stability of 130 mAhg-1 up to 50 cycles at 1.7C.

Low-dimensional (D) materials, such as graphene, transition metal dichalcogenides and chalcogenide nanowires, are attractive for spintronics and valleytronics due to their unique physical and chemical properties resulting from low dimensionality. Emerging concepts of spintronics devices will greatly benefit from using 1D and 2D materials, which opens up new ways to manipulate spin. A majority of 1D and 2D materials is non-magnetic, thus their applications in spintronics are limited. The exploration, design and synthesis of new 1D and 2D materials with intrinsic magnetism and high spin-polarization remains a challenge. In addition, the valley polarization and spin-valley coupling properties of 2D materials have attracted great attention for valleytronics, which not only manipulates the extra degree of freedom of electrons in the momentum space of crystals but also proposes a new way to store the information. The computational investigation of magnetic and electronic properties of low-dimensional materials is the subject of this thesis. We have systematically investigated geometric, electronic, magnetic and valleytronic properties of several 2D and 1D materials by using the density functional theory. These investigations not only theoretically show rich and adjustable magnetic properties of...

MESHWR / Department of Hydrology and Water Resources / This research involves the investigation of the interaction of different sized Nano Gold particles released into municipal drinking water and municipal waste water. Waste water was collected from Malamulele waste water treatment plant and the municipal water was collected at Mintek in Johannesburg, Randburg, South Africa. The waste water was analysed using ICP-MS to detect the metals and anions in it. The results showed the abundance of Sulphur (464 ppm), Calcium (28 ppm), Chloride (27.8 ppm), Iron (20 ppm), Magnesium (8.2 ppm), silicon (6.192 ppm) in descending order and other trace elements, including gold, that were immeasurable (<0.1). The simulated situation was created by adding 20nm gold and 40nm gold nanoparticles into municipal drinking water and waste water and kept at different environmental conditions (light, light and agitation, dark, dark and agitation) under aerobic and anaerobic conditions over a period of two months. Physico-chemical properties (pH and chemical oxygen demand) of the solutions were checked once in a month. The pH fluctuated between the acceptable ranges (5.5 – 9.5) for the two month period. Both municipal water and waste water, with and without gold nanoparticles, under aerobic condition showed an increase in chemical oxygen demand. The gold content in waste water under anaerobic condition showed an increase while under aerobic condition the decline in gold content was evident. The zeta potential of gold nanoparticles in waste water in light and agitation showed (-30 mV) while waste water on other environmental condition (light, dark and dark with agitation) presenting unstable (-18 mV) charge, but the charge shifted positively on the second month rendering them also unstable. Dynamic light scattering and TEM were used to check any possible aggregation or agglomeration of nanoparticles in the waste water. There were some few discrepancies where TEM and DLS contradict, but overall there was no significant probability of any aggregation of gold nanoparticles. The EDX was used to confirm the presence of Au0 in the waste water (with added gold nanoparticles). The research did show that the gold nanoparticles would exist as Au0 in the waste water and thus the discharge of Au-NPs to the sewer system is not recommended, but rather recycle them.

Nanomaterials are playing an increasing role in novel technologies, and it is important to develop optical methods to characterize them in situ.  To that end, backside absorbing layer microscopy (BALM) has emerged as a powerful tool, being capable to resolve sub-nanometer height profiles, with video-rate acquisition speeds and a suitable geometry to couple live experiments.  In the internship, several techniques involving BALM were developed, and applied to study optical and electrical properties of the transition metal dichalcogenide (TMD) monolayer MoS2, a type of 2-dimensional (2D) crystalline semiconductor.  A simulations toolkit was created in MATLAB to model BALM, a workflow to reliably extract linear intensities from the CMOS detector was realized, and 2D MoS2 was synthesized by chemical vapor deposition followed by transfer to appropriate substrates.  BALM data of the 2D MoS2 was acquired and combined with simulations, giving a preliminary result for its complex refractive index at 5 optical wavelengths.  In addition, the first steps towards coupling BALM with a gate biased 2D MoS2 field-effect transistor were explored.  To complement BALM measurements, the grown samples were also characterized by conventional optical microscopy, scanning electron microscopy, atomic force microscopy, photoluminescence spectroscopy, and Raman spectroscopy.  This work provides new additions to an existing platform of BALM techniques, enabling novel BALM experiments with nanomaterial systems.  In particular, it introduces a new alternative for local extraction of optical parameters and for probing of electrical charging effects, both of which are vital in the research and development of nano-optoelectronics.

<div>Photoconductive Semiconductor Switches (PCSS) are metal-semiconductor-metal devices used to switch an electrical signal through photoconduction. Rapidly switched PCSS under high bias voltages have shown remarkable potential for high power electronic and electromagnetic wave generation, but are dependent on precise optoelectronic material parameters such as defect ionization energy and optical absorption. These properties can be measured but are difficult to attribute definitively to specific defects and materials without the aid of high-accuracy, predictive modeling and simulation. This work combines well-established methods for first principles electronic structure calculations such as Density Functional Theory (DFT) with novel modern approaches such as Local Moment Counter Charge (LMCC) boundary conditions to adequately describe charge states and Maximally Localized Wannier Functions (MLWF) to render the summation of optical excitation paths as computationally tractable. This approach is demonstrated to overcome previous barriers to obtaining reliable qualitative or quantitative results, such as DFT band gap narrowing and the prohibitive computational cost of coupled electron-phonon processes. This work contributes electronic structure calculations of 4H-SiC doped with first-row transition metals (V through Ni) that are consistent with prior published work where applicable and add new possibilities for prospective semi-insulating metal-semiconductor systems where investigating new dopant possibilities. The results indicate a spectrum of highly localized, mid-gap, spin-dependent defect energy levels which suggest a wider range of potential amphoteric dopants suitable for producing semi-insulating material. Additionally, this work contributes MLWF-based calculations of phonon-resolved optical properties in 3C and 4H-SiC, indirect gap semiconductors, which accurately produce the expected onset of optical absorption informed by experiment. These results were further expanded upon with small V-doped cells of 4H-SiC, which while not fully converged in terms of cell size still provided a qualitative point of comparison to the ground state results for determining the true optical excitation energy required for substantial photoconductivity. The subsequent speculative analysis suggests the importance of anisotropic absorption and alternative metal defects for optimizing high current optoelectronic devices such as PCSS.</div>

No description available.

Объекты разработки и исследования: канал лазерной стимуляции для измерения электрофизических параметров структуры Ti/TiO2-НТ/Au и канал оптической стимуляции для исследования люминесцентных свойств нанопорошка гексагонального нитрида бора. Цель работы – разработать измерительные каналы лазерной стимуляции исследуемых образцов на основе контроля и управления параметрами излучения в различных режимах в ходе экспериментальных исследований оптически стимулированных и родственных процессов в широкозонных наноструктурированных материалах. В результате работы разработан канал лазерной стимуляции для существующего комплекса по измерению вольт-амперных характеристик на базе микрозондовой станции Cascade Microtech MPS 150, а также модернизирован канал оптической стимуляции на базе люминесцентного спектрометра Perkin Elmer LS 55 со встроенной высокотемпературной приставкой. Реализованные программно-аппаратные измерительные комплексы позволили успешно применить на практике методики исследования широкозонных наноструктур посредством оптически стимулированных процессов. Полученные в ходе работы данные, как для образцов Ti/TiO2-НТ/Au, так и для наноструктурированного порошка h-BN, отлично согласуются с результатами различных исследовательских работ из независимых научных источников. / Objects of development and research: a laser stimulation channel for measuring the electrophysical parameters of the Ti/TiO2-HT/Au structure and an optical stimulation channel for studying the luminescent properties of a hexagonal boron nitride nanopowder. The aim of the work is to develop measuring channels of laser stimulation of the studied samples based on the control and operating of radiation parameters in various modes during experimental studies of optically stimulated and related processes in wide-gap nanostructured materials. As a result of the work, a laser stimulation channel was developed for the existing complex for measuring current-voltage characteristics based on the Cascade Microtech MPS 150 microprobe station, and the optical stimulation channel was modernized on the basis of a Perkin Elmer LS 55 luminescence spectrometer with a built-in high-temperature attachment. The implemented software and hardware measuring systems made it possible to successfully apply in practice the methods of studying wide-gap nanostructures by means of optically stimulated processes. The data obtained during the work, both for the Ti / TiO2-NT / Au samples and for the nanostructured h-BN powder, are in excellent agreement with the results of various research works from independent scientific sources.

No description available.

No description available.

No description available.