<p>Converting wood into paper is a complex process involving many different stages, one of which is pulping. Pulping involves liberating the wood fibres from each other, which can be done either chemically or mechanically. This thesis focuses on the most common chemical pulping method, the kraft cooking process, and especially on a recently developed improvement of the impregnation phase, which is the first part of a kraft cook.</p><p>Extended impregnation kraft cooking (EIC) technique is demonstrated to be an improvement of the kraft pulping process and provides a way to utilize softwood to a higher degree, at higher pulp yield. We demonstrate that it is possible to produce softwood (<em>Picea abies</em>) kraft pulp using a new cooking technique, resulting in a pulp that can be defibrated without inline refining at as high lignin content as 8% on wood, measured as kappa numbers above 90. Lignin is the wood constituent that holds the wood fibres together in the wood matrix. The new cooking technique uses the differences in reaction rate between the diffusion and consumption of hydroxide ions; it is used to ensure a homogenous impregnation of wood chips at lower impregnation temperatures and longer impregnation times than are generally used in the industry. The applied cooking temperatures are also substantially lower than those used in conventional kraft pulping systems, promoting uniform delignification. This results in a narrower kappa number distribution than in lab-cooked conventional kraft pulp.</p><p>High-kappa-number pulps were investigated for pulp sheet properties such as tensile strength, tensile stiffness, and compression strength. It was demonstrated that an EIC pulp of kappa number 95 has strength properties comparable to those of a conventional pulp of kappa number 82. Comparing the effects of starch multilayers on conventional and EIC pulps reveals similar effects. The use of the starch multilayer treatment increased the tensile index and decreased the tensile stiffness and short-span compression test (SCT) indices.</p><p>The EIC technique has also been used to produce a series of bleachable-grade pulps. The results indicate the possibility of increasing the lignin content of the pulp entering the oxygen delignification stage, since the reject content of gently defibered pulp is lower than 0.1% at kappa number 49.</p><p>In this thesis, we recommend that wood chips be impregnated for 2 h at 110 °C to neutralize acidic compounds in the wood and impregnate the chips with cooking chemicals, and that the ensuing cook be performed at 135–140 °C, depending on the target kappa number. We also recommend increasing the available amounts of cooking chemicals in the impregnation stage by using a higher liquor-to-wood ratio and keeping the alkali profile fairly high in the ensuing cook. This concept will reduce the amount of reject material, increase the pulping uniformity, and increase the selectivity towards lignin degradation in the kraft cook.</p> / <p>Omvandling av ved till papper är en komplicerad process som består av många olika steg där ett är massaframställningen (eng. <em>pulping</em>). Massaframställning medför att vedfibrerna frigörs från varandra på kemisk eller mekanisk väg. Denna avhandling fokuserar på den vanligaste kemiska metoden, sulfatkokning och speciellt den nyligen utvecklade förbättringen av impregnerings fasen, som är den första delen av ett sulfatkok. <em></em></p><p>Här visas att<em> Extended Impregnation kraft Cooking </em>(EIC) innebär en förbättring av sulfatkokningen och ett sätt att uppnå högre vedutnyttjande vid högre utbyte för barrved. Vi visar att det är möjligt att producera barrvedsmassa med en ny kokningsprincip som resulterar i en massa som är defibrerbar utan inline-raffinering vid så högt lignin innehåll som 8% (på ved), mätt som kappatal över 90. Lignin är den vedkomponent som håller ihop vedfibrerna i vedmatrisen. Kokningsprincipen utnyttjar skillnaderna i reaktionshastighet mellan diffusion och konsumtion av hydroxidjoner och nyttjas till att skapa en homogen impregnering av vedflisen vid lägre impregneringstemperatur och under längre tid än vad som vanligen används i industrin. De använda koktemperaturerna är också betydligt lägre än vid konventionell sulfatkokning vilket gynnar jämn delignifiering. Detta resulterar i en smalare kappatalsfördelning jämfört med laboratoriekokade konventionella massor.</p><p>Massor med höga kappatal undersöktes med avseende på egenskaper hos handark, såsom dragstyrka, dragstyvhet och kompressionsstyrka Det visades att handark från EIC massa vid kappatal 95 hade jämförbara styrkeegenskaper med konventionell massa vid kappatal 82. Vid jämförelse av effekten av stärkelse multilager på konventionella och EIC massor avslöjar liknande effekter. Användningen av stärkelsemultilager ökade dragindex och minskade dragstyvhets- och kompressions index (SCT, short-compression test).</p><p>Kokprincipen har även använts för att ta fram en serie blekbara massor. Resultaten visar på möjligheten att öka lignininnehållet i massan in till i syrgasdelignifierings-steget eftersom spetinnehållet för milt defibrerad massa var lägre än 0,1% vid kappatal 49.</p><p>I den här avhandlingen rekommenderar vi att vedflis impregneras i 2 timmar vid 110 °C för att neutralisera sura komponenter i veden och impregnera flisen med kokkemikalier, samt att utföra det efterföljande koket vid 135–140 °C beroende på önskat kappatal. Vi rekommenderar även att öka den tillgängliga mängden kokkemikalier i impregneringssteget genom att använda högre vätske-ved förhållande och att hålla alkali profilen relativt hög i det efterföljande koket. Detta koncept reducerar spetmängden, ger jämnare kokning och ökar selektiviteten för nedbrytning av lignin i sulfatkoket.</p>

The project Language of the Book Volume I-III explores the conceptual and the bodily experience of reading and making books. The essay presents the development of Volume I: Narracube consisting of three storytelling prototypes. With Narracube a format was developed that can invite stories to be told beyond single voices, linear time and fixed points of views. Narracube highlights the active role of a medium in transmission of a message. A book is never a neutral container for ink but an active space of communication in its mere contruction despite its content. / Projektet Bokens språk Volume I-III utforskar den konceptuella och kroppsliga upplevelsen av att läsa och göra böcker. Uppsatsen presenterar utvecklingen av Volume I: Narrakub som består av tre prototyper för berättande. Narrakub är ett format som utvecklats för att undersöka hur konstruktionen av boken kan bjuda in berättelser bortom enstaka röster, linjär tid och låsta perspektiv. Narrakub belyser den aktiva rollen som ett medium har då det sänder ett meddelande. En bok är aldrig en neutral behållare för bläck utan bär på ett aktivt kommunikationsutrymme i sin konstruktion oavsett innehåll.

Designing mechanical products in a competitive environment can present unique challenges, and designers constantly search for innovative ways to increase efficiency. One way to save space and reduce cost is to use ortho-planar compliant mechanisms which can be made from sheets of material, or lamina emergent mechanisms (LEMs). This thesis presents principles which can be used for designing LEMs. Pop-up paper mechanisms use topologies similar to LEMs, so it is advantageous to study their kinematics. This thesis outlines the use of planar and spherical kinematics to model commonly used pop-up paper mechanisms. A survey of common joint types is given, as well as an overview of common monolithic and layered mechanisms. In addition, it is shown that more complex mechanisms may be created by combining simple mechanisms in various ways. The principles presented are applied to the creation of new pop-up joints and mechanisms, which also may be used for lamina emergent mechanisms. Models of the paper mechanisms presented in Chapter 2 of the thesis are found in the appendix, and the reader is encouraged to print, cut out and assemble them. One challenge associated with spherical and spatial LEM design is creating joints with the desired motion characteristics, especially where complex spatial mechanism topologies are required. Hence, in addition to a study of paper mechanisms, some important considerations for designing joints for LEMs are presented. A technique commonly used in robotics, using serial chains of revolute and prismatic joints to approximate the motion of complex joints, is presented for use in LEMs. Important considerations such as linkage configuration and mechanism prototyping are also discussed. Another challenge in designing LEMs is creating multi-stable mechanisms with the ability to have coplanar links. A method is presented for offsetting the joint axes of a spatial compliant mechanism to introduce multi-stability. A new bistable spatial compliant linkage that uses that technique is introduced. In the interest of facilitating LEM design, the final chapter of this thesis presents a preliminary design method. While similar to traditional methods, this method includes considerations for translating the mechanism topology into a suitable configuration for use with planar layers of material.