<p>Diss. (sammanfattning) Umeå : Umeå universitet, 1990, härtill 5 uppsatser.</p> / digitalisering@umu.se

Solid wastes containing sulfate, such as construction and demolition debris (CDD), are an important source of pollution, which can create a lot of environmental problems. It is suggested that these wastes have to be separated from other wastes, especially organic waste, and place it in a specific area of the landfill. This results in the rapid rise of the disposal costs of these gypsum wastes. Although these wastes can be reused as soil amendment or to make building materials, a concern has been raised by regulators regarding the chemical characteristics of the material and the potential risks to human health and the environment due to CDD containing heavy metals and a high sulfate content. Soils containing gypsum, namely gypsiferous soils, also have several problems during agricultural development such as low water retention capacity, shallow depth to a hardpan and vertical crusting. In some mining areas, gypsiferous soil problems occur, coupled with acid mine drainage (AMD) problems which cause a significant environmental threat. Reduction of the sulfate content of these wastes and soils is an option to overcome the above mentioned problems. This study aimed to develop sulfate removal systems to reduce the sulfate content of CDD and gypsiferous soils in order to decrease the amount of solid wastes as well as to improve the quality of wastes and soils for recycling purposes or agricultural applications. The treatment concept leaches the gypsum contained in the CDD by water in a leaching step. The sulfate containing leachate is further treated in biotic or abiotic systems. Biological sulfate reduction systems used in this research were the Upflow Anaerobic Sludge Blanket (UASB) reactor, Inverse Fluidized Bed (IFB) Reactor and Gas Lift Anaerobic Membrane Bioreactor (GL-AnMBR). The highest sulfate removal efficiency achieved from these three systems ranges from 75 to 95%. The treated water from the bioreactor can then be reused in the leaching column. Chemical sulfate removal (abiotic system) is an alternative option to treat the CDD leachate. Several chemicals were tested including barium chloride, lead(II) nitrate, calcium chloride, calcium carbonate, calcium oxide, aluminium oxide and iron oxide coated sand. A sulfate removal efficiency of 99.9% was achieved with barium chloride and lead(II) nitrate.For AMD and gypsiferous soils treatment, five types of organic substrate including bamboo chips (BC), municipal wastewater treatment sludge (MWTS), rice husk (RH), coconut husk chip (CHC) and pig farm wastewater treatment sludge (PWTS) were tested as electron donors for biological sulfate reduction treating AMD. The highest sulfate reduction efficiency (84%) was achieved when using the combination of PWTS, RH and CHC as electron donors. Then, this organic mixture was further used for treatment of the gypsiferous soils. The gypsum mine soil (overburden) was mixed with an organic mixture in different amounts including 10, 20, 30 and 40% of soil. The highest sulfate removal efficiency of 59% was achieved in the soil mixture which contained 40% organic material.The removal of sulfide from the effluent of the biological sulfate reduction process is required as sulfide can cause several environmental impacts or be re-oxidized to sulfate if directly discharged to the environment. Electrochemical treatment is one of the alternatives for sulfur recovery from aqueous sulfide. A non-catalyzed graphite electrode was tested as electrode for the electrochemical sulfide oxidation. A high surface area of the graphite electrode is required in order to have less internal resistance as much as possible. The highest sulfide oxidation rate was achieved when using the external resistance at 30 Ω at a sulfide concentration of 250 mg L-1

Purpose: The building sector accounts for 40 % of the total energy consumption in Sweden today, and the largest proportion is consumed during the operating phase. From the year 2020 and onwards, all new buildings should be erected as zero-emissionbuildings. The building’s design can reduce energy demands, but the current legal requirements do not favour energy-efficient designs. This study focuses on the design’s importance for the energy efficiency of buildings, i.e., energy-saving design. The impact of specific measures is difficult to calculate due to the complexity of reality. This study aims to highlight the measures that could reduce energy consumption in commercial buildings. Method: In order to provide answers to the issues stated in the report and to achieve the objective of the study, case studies are being conducted investigating three commercial buildings where deliberate decisions were made to use energy-reducing measures. Results and conclusions are based on qualitative interviews and literature studies. Findings: The energy-reducing design measures found to be of most importance used in the studied buildings are the form factor, the window portion and the thermal storage capacity. Moreover, significant savings are possible by carefully consider how solar energy can be limited or used in the building. Generally, buildings tends to become more technical, therefore technical knowledge early in the process is important to reach a good result. Economic incentives and clear objectives with right focus are also important for optimizing a building’s energy performance. The wording and the requirement levels in the Swedish building regulations highly controls the construction of energy efficient buildings. Implications: This study shows how energy efficient design is made today and provides an indication of what can be done and what should be prioritized. By imposing requirements on consumed energy instead of bought, energy efficient design could be favoured. Furthermore, this study suggests that a balance between windows, façade and solar shading are important energy-reducing measures. Regardless of selected energyreducing measures, a good performance is essential. Finally, this study shows that a methodical use of existing knowledge and technology makes a difference. Limitations: A lifecycle approach provides an overall picture of a building’s energy consumption. However, this study is based on the energy consumption during the operating phase. The result of this study does not take economic or aesthetic factors into account. This study is a comparative case study and is based on few but carefully matched cases. The selected cases are commercial buildings where deliberate decisions were made to use energy-reducing measures.

No description available.

[pt] Este trabalho teve por objetivo avaliar a morfologia de biofilmes, formados em superfície de aço API 5L X80 submetida a um fluido com baixo BSW (Basic Sediment Water), ou seja, baixo teor de água em óleo, através de análise por Microscopia Eletrônica de Varredura (MEV), determinar a cinética e quantificar os grupos bacterianos de formação destes biofilmes, e avaliar a biocorrosão causada por estes microrganismos. Foram realizadas alterações no protocolo original de preparo de amostras, com a finalidade de obter melhor definição das morfologias avaliadas. Realizaram-se estudos dinâmicos (looping) e em condições estáticas, com e sem a adição de agente biocida. Utilizando-se como fluido de processo o óleo coletado no terminal da Petrobras em Barra do Furado que tem como característica um BSW de aproximadamente 1 por cento de água. Para alcançar os objetivos descritos foram quantificadas bactérias sésseis (bactérias facultativas heterotróficas, bactérias precipitantes do ferro, bactérias anaeróbias heterotróficas e bactérias redutoras de sulfato) através da técnica do número mais provável (NMP). A intensidade do processo corrosivo foi avaliada através da análise dos pites formados nos cupons por microscopia óptica. A seqüência de fixação com alteração do protocolo inicial, permitiu uma melhor preservação estrutural do biofilme obtendo-se assim imagens com melhor resolução, tendo em vista que a fixação primária com glutaraldeído fixa principalmente proteínas pelo estabelecimento de ligações divalentes com grupamento amino, e a pós-fixação em tetróxido de ósmio reage com os lipídios. Quanto a cinética, observou-se também que na presença de fluido oleoso, a formação do biofilme só é detectada após 15 dias de exposição. A adição do agente biocida inibiu o crescimento do biofilme, não sendo detectada a presença de células cultiváveis após 7 dias em contato com o fluido contendo o agente químico. / [en] This study aims to evaluate the morphology of biofilms formed on the surface of API 5L X80 steel exposed to a low BSW (Basic Sediment Water) fluid comprising oil of a low water content. The analisys was performed using scanning electron microscopy (SEM) in order to determine the formation kinetics, to quantify and identify the bacterial groups present as the film formed, and to evaluate the biocorrosion caused by these organisms. Modifications were made to the original sample preparation protocol, in order to better define the film morphologies. Studies were undertaken applying either static or dynamic (looping) conditions, bith with and without the addition of biocides. The process fluid used was oil collected from the Petrobras Barra do Furado Terminal, characterized by its 1 percent BSW. The evaluation was performed quantifying the sessile bacteria present in the film (heterotrophic bacteria, iron bacteria, anaerobic bacteria e sulphate reducing bacteria) via the Most Probable Number (MPN) technique. The intensity of the corrosion process was determined by the analysis of pits forme in the testpieces, by optical microscopy. The application of a sample fixation sequence, in addition to modifications of the inicial sample preparation protocol, permitted the improved preservation of the biofilm structures, thereby permitting higher resolution images. The primary fixing agent, containing gluteraldehyde, principally fixes proteins, by establishing divalent bonds with amino groups, while the post-fixation stage with osmium tetroxide invloves reactions with lipid groups.With regard to the film deposition kinetics, it was observed that biofilm formation could only be detected after 15 day s exposure to the oily fluid. The addition of a biocide, inhibited the growth of the film, no cultivatable cells being present after 7 days contact with the treated fluid.

This paper addresses the question of whether individual delinquent behaviour, or criminogenic risks that lead to it, can be reduced for convicted violence offenders with personality disorder, using the newly developed offence-oriented therapeutic program TERČ ("TARGET"). If so, how will these changes manifest in the recidivism rate, and how they will reflect the personality characteristics of inmates. TARGET was first systematically applied within a special treatment unit for prisoners with mental and behavioral disorders in Liberec Remand Prison in 2008. It is based on selected elements of the Ambulant intensive program (AIP) from Switzerland. A total of 100 convicts were entered TARGET from 2008 to 2015. 65 individuals completed the program successfully, and 57 were released again. The already released graduates of TARGET re-offended within 12 months in 10.4%. Of all admitted TARGET participants, a total of 30.2% either relapsed or failed during the program since 2009. Graduates showed positive, statistically significant changes in the monitored areas of life satisfaction, emotional stability, insight, self-control and aggression, while on scales representing personality disorder no positive, statistically significant effect was observed. For later re-offending prisoners, the changes were...

Submitted by Bruna Rodrigues (bruna92rodrigues@yahoo.com.br) on 2016-09-21T14:11:42Z No. of bitstreams: 1 DissRDC.pdf: 7324446 bytes, checksum: 5e04b539c5f14da2f1e2fb0184498eb9 (MD5) / Approved for entry into archive by Marina Freitas (marinapf@ufscar.br) on 2016-09-21T18:26:41Z (GMT) No. of bitstreams: 1 DissRDC.pdf: 7324446 bytes, checksum: 5e04b539c5f14da2f1e2fb0184498eb9 (MD5) / Approved for entry into archive by Marina Freitas (marinapf@ufscar.br) on 2016-09-21T18:26:47Z (GMT) No. of bitstreams: 1 DissRDC.pdf: 7324446 bytes, checksum: 5e04b539c5f14da2f1e2fb0184498eb9 (MD5) / Made available in DSpace on 2016-09-21T18:26:54Z (GMT). No. of bitstreams: 1 DissRDC.pdf: 7324446 bytes, checksum: 5e04b539c5f14da2f1e2fb0184498eb9 (MD5) Previous issue date: 2014-07-28 / Não recebi financiamento / The homogenizing heat treatment of aluminium billets has direct influence on extrusion process productivity, surface quality and mechanical properties of extruded shapes. The homogenizing process parameters that impacts on metallurgical properties of 6063 alloys are: temperature, time and cooling rate. The maximum recommended homogenizing temperature for 6063 alloy is 590ºC. The minimum homogenizing time is 2,25h. The minimum cooling rate recommended is 400ºC/h. As for extrusion logs homogenizing process of 6063 6” diameter at Sapa Aluminium Brasil the furnace is a process bottleneck for logs production, this work has investigated about the possibility of time reducing without negative impacts on billet metallurgical properties and without detrimental impacts on productivity of extrusion process and quality of its products. This investigation was done by billet metallographic analysis, cold and hot mechanical tests and extrusion/anodizing trials for different homogenizing time conditions. The results have shown that the time reducing did not cause negative impacts for metallurgical neither for mechanical properties and because of that no detrimental effects for extrusion performance and surface finish and anodized quality was observed. Hence, was possible to decrease 20 minutes on homogenizing time and gain 14,5% of productivity on heat treatment process. / O tratamento térmico de homogeneização de tarugos de alumínio tem influência direta na produtividade do processo de extrusão, na qualidade superficial e nas propriedades mecânicas dos perfis extrudados. As variáveis do tratamento térmico da liga 6063 que influem na qualidade metalúrgica são: temperatura, tempo e taxa de resfriamento. Para liga 6063, a máxima temperatura recomendada de homogeneização é de 590ºC. O tempo mínimo para a homogeneização é de 2,25h. A taxa de resfriamento mínima recomendada é 400ºC/h. Como para o tratamento térmico de tarugos de 6” há um gargalo no forno de homogeneização da Sapa Aluminium Brasil, investigouse neste trabalho possibilidades de redução de tempo no processo de homogeneização evitando impactos negativos na qualidade metalúrgica dos tarugos e/ou na performance dos tarugos no processo de extrusão. Tal investigação foi feita através de análises metalográficas, ensaios mecânicos a frio (dureza e tração) e a quente (torção) e testes práticos no processo de extrusão/anodização para amostras retiradas de tarugos homogeneizados em diferentes condições de tempo de homogeneização. Os resultados obtidos mostraram que a redução no tempo de homogeneização não impactou negativamente na qualidade metalúrgica dos tarugos e nem em suas propriedades mecânicas a frio e que as pequenas variações ocorridas mantiveram-se dentro dos limites de especificação e não reduziram a performance do processo de extrusão bem como as propriedades mecânicas e qualidade superficial dos perfis extrudados. Com isso, foi possível reduzir 20 minutos no tempo de tratamento térmico de homogeneização e gerar um ganho de produtividade de 14,5% no processo.

Os micro-organismos constituem um grande problema em termos econômicos para a indústria petrolífera. Estes são responsáveis pela produção de substâncias corrosivas e a formação de biofilmes, que causam deterioração dos materiais metálicos. Os principais grupos microbianos presentes em amostras ambientais da indústria do petróleo são as bactérias anaeróbias heterotróficas totais (BANHT) e as bactérias redutoras de sulfato (BRS). Atualmente, a quantificação desses grupos microbianos é realizada através da técnica do Número Mais Provável (NMP) que estima o resultado em aproximadamente 28 dias. Neste trabalho foi otimizada uma metodologia para a microscopia de fluorescência de amostras salinas provenientes de tanques de armazenamento de água/óleo. As condições testadas foram o tipo de óleo de imersão, o tipo de diluente, o volume do corante, o volume da amostra corada e a concentração do fixador (glutaraldeído) numa tentativa de correlacionar com resultados de quantificação de BANHT e BRS através da técnica convencional do NMP. Nesse caso, as células totais foram quantificadas por microscopia de fluorescência utilizando o corante fluorescente laranja de acridina (AO). Verificou-se que houve uma correlação entre os resultados da quantificação de células totais por microscopia de fluorescência e os resultados de BANHT pela técnica do NMP, devido a pouca variação de valores expressos em ambas as quantificações. Entretanto, não foi possível correlacionar os resultados da quantificação de células totais com os resultados de BRS por NMP devido à grande variação dos valores de quantificação de BRS. Na microscopia de fluorescência, foi possível, quantificar os micro-organismos em aproximadamente 30 minutos e através das fotografias, verificou-se ainda que as amostras apresentaram-se nítidas e os micro-organismos com uma boa fluorescência / Microbial cells constitute a severe problem, from the economic point of view, for the petroleum industry. They are responsible for the production of corrosive metabolites and for the formation of biofilms, causing deterioration in the surface of metallic materials. The main microbial groups present in environmental samples from the petroleum industry include total anaerobic heterothrophic bacteria (TANHB) and sulfate-reducing bacteria (SRB). Nowadays, the quantification of those microbial groups is performed through the use of the most probable number technique (MPN), providing the final quantification after 28 days. In the present work a new methodology, based on fluorescence microscopy, was optimized on saline samples from water/oil storage tanks. The conditions tested were the type of immersion oil, type of diluent, the volume of the dye, the stained sample volume and concentration of fixative (glutaraldehyde) in order to quantify total cells, in an attempt to correlate with TANHB and SRB quantification through MPN. In that case, total cells were quantified with the help of acrydine orange as fluorescent dye. It could be observed a clear correlation between the results obtained for total cells quantification by fluorescence microscopy and the results obtained for TANHB through MPN technique, due to the negligible differences observed in both quantifications. However, when a correlation with SRB cells was tried results of total cells through fluorescence microscopy did not fit entirely. With the use of fluorescence microscopy, it was possible to quantify microbial cells in around 30 minutes and with the help of photographic reports obtained, it could be observed that the samples were clearly observed and the microbial cells indicated a good fluorescence

Thesis focuses on social security system at Czech Republic, mainly on health insurance area. The aim of the thesis is to analyze healt insurance development, which projects itself into calculations of healt insurance allowances (sickness compensation, motherhood financial support and nursing compensation) and to evaluate influence of legislative changes during observed period of time (2005 {--} 2010) at these calculations. Thesis is divided into two parts, theoretical one, which describes all social security system areas as they were at year 2005 from the employee point of view and from the accounting viewpoint as well. Second part consists from five chaptures, where is gradually described choosen company {--} Southbohemian regional veterinary administration {--} profile, it´s social security obligations as an employer, calculations of healt insurance allowances and in conclusion results evaluation and legislative changes influence assesment.

Submitted by Luciana Ferreira (lucgeral@gmail.com) on 2015-12-08T07:46:47Z No. of bitstreams: 2 Dissertação - Letícia Freire de Oliveira - 2015.pdf: 1336117 bytes, checksum: d7d9a7965dc7492a12ce5fcb44c65555 (MD5) license_rdf: 23148 bytes, checksum: 9da0b6dfac957114c6a7714714b86306 (MD5) / Approved for entry into archive by Luciana Ferreira (lucgeral@gmail.com) on 2015-12-08T07:48:34Z (GMT) No. of bitstreams: 2 Dissertação - Letícia Freire de Oliveira - 2015.pdf: 1336117 bytes, checksum: d7d9a7965dc7492a12ce5fcb44c65555 (MD5) license_rdf: 23148 bytes, checksum: 9da0b6dfac957114c6a7714714b86306 (MD5) / Made available in DSpace on 2015-12-08T07:48:34Z (GMT). No. of bitstreams: 2 Dissertação - Letícia Freire de Oliveira - 2015.pdf: 1336117 bytes, checksum: d7d9a7965dc7492a12ce5fcb44c65555 (MD5) license_rdf: 23148 bytes, checksum: 9da0b6dfac957114c6a7714714b86306 (MD5) Previous issue date: 2015-04-07 / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior - CAPES / The peach palm is a native Palm from humid tropics of the Amazon, used for the production of palm raw or pickled, becoming an important alternative to reduction of predatory exploitation of other palms. The sheath, external, middle and internal, that involve the noble party, called palm or palmetto, are not used during the plicked of palm processing, yielding tons of waste, and the production of flour, is an excellent alternative to the use of these. This research, therefore, aimed the physical, chemical, technological and toxicological study, of the waste sheaths flour, external, middle and internal, peach palm (PF). The flour has a low moisture content (4.74%), proteins (5.03 g(100g)-1), lipids (2.12 g(100g)-1), soluble dietary fiber (3.40 g(100g)-1), ash (4.69 g(100g)-1) and high content of insoluble dietary fiber (49,53 g(100g)-1). Regarding water absorption, milk and oil, the flour had good absorption capacity. The flour showed low acidity (1.36%), clear and attractive coloring, and the particle size was presented between fine and very fine. It was noted, also, high amount of resistant starch (20%) and the presence of reducing sugars as fructose (6.70 g(100g)-1) and glucose (7.50 g(100g)-1). The most significant amino acid were glutamic acid (392.63 mg(100g)-1), arginine (363.76 mg(100g)-1), aspartic acid (348.93 mg(100g)-1). The PF and waste sheaths, external, middle and internal, fresh, of peach palm (WP) showed low amounts of phytic acid, condensed tannins and hydrolysates. The PF showed 100% of protein digestibility, and the lyophilized aqueous extract of waste sheaths flour, external, middle and internal of peach palm (PE), showed low toxicity. The results of this research suggest that the PF can be used in bakery products such as breads, cookies and cakes, besides the application in meat products, milk drinks, cheese, among others, contributing, nutritionally, in addition or partial replacement of flour wheat in processed foods, without to reduce the bioavailability of nutrients, representing too, toxicological safety, due to the absence of toxic compounds in PE. / A pupunheira é uma palmeira nativa dos trópicos úmidos da Amazônia, utilizada para a produção de palmito in natura ou em conserva, tornando-se uma importante alternativa para a redução da exploração predatória de outras palmeiras. As bainhas, externa, mediana e interna, que envolvem a parte nobre, denominada palmito, não são aproveitadas durante o processamento do palmito em conserva, gerando toneladas de resíduos, sendo, a produção de farinha, excelente alternativa para o aproveitamento desses. Este trabalho, portanto, teve como objetivo o estudo físico, químico, tecnológico e toxicológico, da farinha das bainhas residuais, externa, mediana e interna, da pupunha (FP). A farinha obtida possui baixo teor de umidade (4,74%), proteínas (5,03 g(100g)-1), lipídios (2,12 g(100g)-1), fibra alimentar solúvel (3,40 g(100g)-1), cinzas (4,69 g(100g)-1) e alta quantidade de fibra alimentar insolúvel (49,53 g(100g)-1). Em relação à absorção em água, leite e óleo, a farinha apresentou boa capacidade de absorção. A farinha apresentou baixa acidez (1,36%), coloração clara e atrativa, e a granulometria apresentou-se entre fina e muito fina. Notou-se, também, alta quantidade de amido resistente (20%) e a presença de açúcares redutores como, frutose (6,70 g(100g)-1) e glicose (7,50 g(100g)-1). Os aminoácidos mais expressivos foram o ácido glutâmico (392,63 mg(100g)-1) arginina (363,76 mg(100g)-1) e ácido aspártico (348,93 mg(100g)-1). A FP e as bainhas residuais, externas, medianas e internas, in natura, do palmito de pupunha (PN), apresentaram baixa quantidade de ácido fítico, taninos condensados e hidrolisados. A FP apresentou 100 % de digestibilidade de proteína, e o extrato aquoso liofilizado da farinha das bainhas residuais, externa, mediana e internas da pupunheira (EP), apresentou baixa toxicidade. Os resultados deste estudo sugerem que a FP pode ser empregada em produtos de panificação, como pães, biscoitos e bolos, além da aplicação em produtos cárneos, bebidas lácteas, queijos, entre outros, contribuindo, nutricionalmente, na adição ou substituição parcial à farinha de trigo, em alimentos industrializados, sem que haja redução da biodisponibilidade de nutrientes, representando também, segurança toxicológica, devido à ausência de compostos tóxicos no EP.