The increased concentration of greenhouse gases in theatmosphere, in particular CO2, is changing the Earth’s climate. Accordingto the Kyoto protocol, where the international community agreedon binding emission targets, developed countries are committedto reduce their greenhouse gas emissions. The increased use ofbiomass in energy systems is an important strategy to reduce CO2emissions. The purpose of this thesis has been toanalyse the opportunities for Sweden to further reduce CO2emissions in the energy system, by rationallyutilising woody biomass energy. The characteristics of currentcommercially operating biofuel-based CHP plants in Sweden aresurveyed and systematically presented. A consistent andtransparent comprehensive reference base for system comparisonsis given. Furthermore, the fuel effectiveness and contributionto CO2reduction is calculated. The governmentalsubsidies of the CHP plants’investment, expressed as costof specific CO2reduction, appears to be low. The competitiveness of biomass-fuelled energy production inrelation to fossil-based production with carbon capture isanalysed, showing that the biomass-fuelled systems provide acompetitive option, in terms of cost of electricity andefficiencies. The remaining Swedish woody biofuel potential ofat least 100 PJ/yr is principally available in regions with abiomass surplus. Transportation is therefore required to enableits utilisation in a further national and international market.Refining the biofuel feedstock to pellets, or even furtherrefining to motor fuels (DME, methanol or ethanol) or power,could facilitate this transport. Different options for fuelrefining are studied and compared. The entire fuel chain, fromfuel feedstock to end users, is considered and CO2emissions are quantified. Substituting fuelpellets for coal appears to be the most costeffectivealternative and shows the largest CO2reduction per energy unit biofuel. Motor fuelsappear more costly and give about half the CO2reduction. Transportation of the upgraded biofuelpellets is highly feasible from CO2emissions point of view and does not constitute ahindrance for further utilisation, i.e. the pellets can betransported over long distances efficiently with only limitedemissions of CO2. Bioenergy utilisation has additional features forenvironmental improvement, apart from the CO2aspect. Waste heat from biofuel-based CHP can becost-effectively used in conjunction with sewage treatment. Theincoming sewage water to the nitrification process can bepreheated with the waste heat, and thereby substantiallyenhance the nitrification and the reduction of ammoniumnitrogen during the winter season. <b>Keywords:</b>CO2reduction, energy system, biofuel, CHP, refining,fuel pellets, ethanol, methanol, DME, fuel substitution, sewagewater, nitrification.

<p>The risk for climate change is a growing concern for theglobal society. According to what is known as the Kyoto Protocol,developed countries have committed themselves to reduce theirgreenhouse gas (GHG) emissions. The purpose of this thesis hasbeen to analyse opportunities for CO2 reductions in Swedish pulpand paper mills. The pulp and paper industry accounts forsignificant shares of the Swedish utilisationof both electricityand, in particular, biomass fuels. In this thesis, it has been agoal to focus not only on the technical potential of alternativesfor CO2 reductions in the energy systems of pulp and paper mills,but also on analysing the costeffectiveness of the studiedmeasures. Moreover, the analysis has covered questions concerningthe capacity and willingness among the actors involved with thepulp and paper mills’energy systems to realise CO2reduction potentials.</p><p>A broad techno-economical evaluation of available technologiesfor increased power production as well as more efficient energyutilisation is carried out. Furthermore, a more indepth analysisof pulp mill-based biomass energy with CO2 removal and permanentsequestration (BECS) is presented. An evaluation is made of thepotential for pulp and paper production with a negative CO2balance through the implementation of BECS. In recent yearsoutside suppliers, mainly energy service companies (ESCOs), havebegun to operate energy facilities in some Swedish pulp and papermills. Based on interviews with managers from pulp and papercompanies and ESCOs, the main driving forces behind theincreasing co-operation as well as the opportunities and riskswith energy related co-operation are presented.</p><p>Furthermore, the technical possibility of carbon-negativitythrough the implementation of BECS is discussed in relation tocarbon management on both corporate and global levels. The extentto which CO2-reducing measures in pulp and paper mills arerealised will have an impact on Sweden’s capacity to reachCO2 reduction targets. Whether or not technologies for CO2capture and sequestration are developed and implemented inSwedish pulp mills has a very large impact on the size ofSweden’s long-term CO2 reduction potential. Moreover, thedevelopment of business and competence focus in pulp and papercompanies and ESCOs suggests that cooperation will become ofincreasing importance for future sustainable industrial energymanagement.</p><p><b>Keywords:</b>CO2 reduction, pulp and paper industry, energysystem, biomass, CO2 capture and sequestration, black liquor,gasification, power production, outsourcing, sustainable energymanagement</p>

<p>The increased concentration of greenhouse gases in theatmosphere, in particular CO₂, is changing the Earth’s climate. Accordingto the Kyoto protocol, where the international community agreedon binding emission targets, developed countries are committedto reduce their greenhouse gas emissions. The increased use ofbiomass in energy systems is an important strategy to reduce CO₂emissions. The purpose of this thesis has been toanalyse the opportunities for Sweden to further reduce CO₂emissions in the energy system, by rationallyutilising woody biomass energy. The characteristics of currentcommercially operating biofuel-based CHP plants in Sweden aresurveyed and systematically presented. A consistent andtransparent comprehensive reference base for system comparisonsis given. Furthermore, the fuel effectiveness and contributionto CO₂reduction is calculated. The governmentalsubsidies of the CHP plants’investment, expressed as costof specific CO₂reduction, appears to be low.</p><p>The competitiveness of biomass-fuelled energy production inrelation to fossil-based production with carbon capture isanalysed, showing that the biomass-fuelled systems provide acompetitive option, in terms of cost of electricity andefficiencies. The remaining Swedish woody biofuel potential ofat least 100 PJ/yr is principally available in regions with abiomass surplus. Transportation is therefore required to enableits utilisation in a further national and international market.Refining the biofuel feedstock to pellets, or even furtherrefining to motor fuels (DME, methanol or ethanol) or power,could facilitate this transport. Different options for fuelrefining are studied and compared. The entire fuel chain, fromfuel feedstock to end users, is considered and CO₂emissions are quantified. Substituting fuelpellets for coal appears to be the most costeffectivealternative and shows the largest CO₂reduction per energy unit biofuel. Motor fuelsappear more costly and give about half the CO₂reduction. Transportation of the upgraded biofuelpellets is highly feasible from CO₂emissions point of view and does not constitute ahindrance for further utilisation, i.e. the pellets can betransported over long distances efficiently with only limitedemissions of CO₂.</p><p>Bioenergy utilisation has additional features forenvironmental improvement, apart from the CO₂aspect. Waste heat from biofuel-based CHP can becost-effectively used in conjunction with sewage treatment. Theincoming sewage water to the nitrification process can bepreheated with the waste heat, and thereby substantiallyenhance the nitrification and the reduction of ammoniumnitrogen during the winter season.</p><p><b>Keywords:</b>CO₂reduction, energy system, biofuel, CHP, refining,fuel pellets, ethanol, methanol, DME, fuel substitution, sewagewater, nitrification.</p>

Biomass-fuelled proton exchange membrane fuel cells (PEMFCs) offer asolution for replacing fossil fuel for hydrogen production. Through using thebiomass-derived hydrogen as fuel, PEMFCs may become an efficient andsustainable energy system for small and medium-sized enterprises. The aim ofthis thesis is to evaluate the performance and potential applications of biomassfuelledPEMFC systems which are designed to convert biomass to electricity andheat. Biomass-fuelled PEMFC systems are simulated by Aspen plus based ondata collected from experiments and literature.The impact of the quality of the hydrogen-rich gas, anode stoichiometry, CH4content in the biogas and CH4 conversion rate on the performance of the PEMFCis investigated. Also, pinch technology is used to optimize the heat exchangernetwork to improve the power generation and thermal efficiency.For liquid and solid biomass, anaerobic digestion (AD) and gasification (GF),respectively, are relatively viable and developed conversion technologies. ForAD-PEMFC, a steam reformer is also needed to convert biogas to hydrogen-richgas. For 100 kWe generation, the GF-PEMFC system yields a good technicalperformance with 20 % electrical efficiency and 57 % thermal efficiency,whereas the AD-PEMFC system only has 9 % electrical efficiency and 13 %thermal efficiency. This low efficiency is due to the low efficiency of theanaerobic digester (AD) and the high internal heat consumption of the AD andthe steam reformer (SR). For the environmental aspects, the GF-PEMFC systemhas a high CO2 emissions offset factor and the AD-PEMFC system has anefficient land-use.The applications of the biomass-fuelled PEMFC systems are investigated on adairy farm and an olive oil plant. For the dairy farm, manure is used as feedstockto generate biogas through anaerobic digestion. A PEMFC qualified for 40 %electrical efficiency may generate 360 MWh electricity and 680 MWh heat peryear to make a dairy farm with 300 milked cows self-sufficient in a sustainableway. A PEMFC-CHP system designed for an olive oil plant generating annual 50000 m3 solid olive mill waste (SOMW) and 9 000 m3 olive mill waste water(OMW) is simulated based on experimental data from the Biogas2PEM-FCproject1. After the optimization of the heat exchanger network, the PEMFC-CHP  system can generate 194 kW electricity which corresponds to 62 % of the totalelectricity demand of the olive oil plant.The economic performance of the PEMFC and biogas-fuelled PEMFC areassessed roughly including capital, operation &amp; maintenance (O&amp;M) costs of thebiogas plant and the PEMFC-CHP, the cost of heat and electricity, and the valueof the digestate as fertilizer. / <p>QC 20151109</p>

This thesis puts forth the means of a strategic approach to address a persistent problem in the energy system and in this way, to transition the built environment to a future state that is more exergy-aware to curb CO2 emissions. Such a vision is made possible by the six-fold contributions of the research work: I) An analytical model is developed, which for the first time, formulates the CO2 emissions that are compounded in the energy system as a function of the systematic failures to match the supply and demand of exergy. This model is namely the Rational Exergy Management Model or REMM. II) REMM is then applied to analyze the pathways in which it is possible to lead the built environment into addressing structural overshoots in its exergy supply to curb CO2 emissions. The cases that embody these pathways are also analyzed over a base case, including cases for sustainable heating and cooling. III) New tools are designed to augment decision-making and exemplify a paradigm shift in the more rational usage of exergy to curb CO2 emissions. These include a scenario-based analysis tool, new options for CO2 wedges, and a multi-fold solution space for CO2 mitigation strategies based on REMM. IV) The concept of a net-zero exergy building (NZEXB) is developed and related to REMM strategies as the building block of an exergy-aware energy system. The target of a NZEXB is further supported by key design principles, which address shortcomings in state-of-the-art net-zero design. V) A premier building that deployed the key design principles to integrate building technology in an innovative, exergy-aware design and received LEED Platinum is analyzed on the basis of the NZEXB target. The results validate that this building boosts net self-sufficiency and curbs compound CO2 emissions, which are then presented in a proposed scheme to benchmark and/or label future NZEXBs. VI) Based on the scalability of the best-practices of the NZEXB ready building, the means to realize a smarter energy system that has exergy-aware relations in each aspect of the value chain to curb CO2 emissions are discussed. This includes a target for such a network at the community level, namely a net-zero exergy community (NZEXC). As a whole, the results of the thesis indicate that the strategic approach as provided by REMM and the NZEXB target of the research work has the potential to steer the speed and direction of societal action to curb CO2 emissions. The thesis concludes with a roadmap that represents a cyclical series of actions that may be scaled-up at various levels of the built environment in a transition to be in better balance with the Planet. / QC 20111014

An eight-lot residential subdivision in central Wairarapa is being developed to demonstrate the principles of sustainable resource management. Local energy sources for low and high grade use, including electricity sourced from proposed grid-integrated, on-site, distributed generation will supplement imported network electricity. A unique component is an internal loop grid for lot connection that interfaces with the local network through a single connection point. A decision model was designed as a decision-support tool for the development based on the annual supply-demand electrical energy balance, site infrastructure covenants and a range of economic and technology criteria. Solar and wind resources were assessed for potential supply of electricity to the community energy system. Three demand profiles were developed using supplied and estimated electrical demand data; and included assumptions on thermal performance of the houses, the use of low-grade heat, user behaviour, and appliance use. Supply and demand were analysed as daily average profiles by hour for each month of the year. The decision model outputs were designed to give a graphic view of the system options. The accompanying output datasets also enabled a number of scenarios for connection configurations, load management, and economic sensitivity to be explored for their impact on the communal approach to managing energy. The viability of the community energy system is significantly influenced by managing demand level in conjunction with system size, capital cost management, and tariffs for electricity import and export. Energy requirements could be best met in the short term by installing a site-wide mixed generation system of sized capacity between 5 and 11kW, supported by metering and information technology to deliver management data to the residents. Future research opportunities exist to continue monitoring technical, economic and social outcomes from this unique community development. Incentivising private investment in userfocussed energy innovations is an option for New Zealand to consider in the current climate of market-driven large scale electricity developments.

Considerando que a duração do combate de judô pode variar entre poucos segundos até um período superior a 5 min, a caracterização da demanda fisiológica do combate na sua duração regulamentar e fracionada, assim como a relação dessas respostas com o nível de aptidão aeróbia e anaeróbia dos atletas é relevante para o aperfeiçoamento dos métodos de treinamento. Assim, o objetivo do presente estudo foi analisar a aptidão física, ações técnicas e respostas fisiológicas durante a luta de judô com diferentes durações. Para tanto, 12 atletas de judô foram submetidos a 10 sessões de avaliação. Nas duas primeiras sessões foram realizados quatro testes físicos para caracterização da aptidão aeróbia e anaeróbia dos membros superiores e inferiores. Nas demais sessões, os atletas foram submetidos a 15 combates simulados de judô (3 condições x 5 durações - 1, 2, 3, 4 e 5 min) com o mesmo oponente, em ordem aleatória e vendados quanto à duração do combate. Em uma das condições, os atletas simularam um combate real. Na segunda condição, os atletas lutaram usando um analisador de gases para mensurar o consumo de oxigênio, para a estimativa da contribuição dos sistemas de transferência de energia. Nessa condição foram impostas algumas adaptações de movimento. Para verificar se o uso do analisador de gases modificou as respostas obtidas, na terceira condição, os atletas lutaram com as mesmas adaptações, porém não usaram o equipamento. Em cada sessão foram conduzidos dois combates, intercalados por 60 min de recuperação. Foram quantificadas as respostas fisiológicas, perceptivas, de desempenho, de estrutura temporal e ações técnicas em todos combates. A comparação das variáveis dependentes foi realizada com uma análise de modelos mistos para medidas repetidas, seguida do post hoc de Bonferroni. As associações entre a aptidão aeróbia e anaeróbia com as variáveis do combate foram verificadas por meio da correlação de Pearson. Para todas as comparações pareadas significantes foi calculado o tamanho do efeito (d de Cohen). Em todas as análises foi adotado 5% como nível de significância. Os principais resultados demonstraram aumento da contribuição aeróbia com concomitante redução da contribuição dos sistemas anaeróbios com o transcorrer do combate, sendo a contribuição aeróbia superior à contribuição dos sistemas anaeróbios a partir do primeiro min de combate. O sistema anaeróbio lático contribuiu com a menor proporção do custo energético do combate de judô. As taxas de incremento das respostas fisiológicas e perceptivas por min de combate foram reduzidas com o transcorrer do combate, sendo as principais modificações observadas no início do combate, sugerindo que os atletas podem apresentar estratégia para modular seus esforços. Com o transcorrer do combate observou-se manutenção do tempo médio de esforço e ações aplicadas, porém houve aumento do tempo médio dos períodos de pausa. Após a realização do combate observou-se declínio da resistência muscular dinâmica dos membros superiores, manutenção da força isométrica máxima de preensão manual e melhora da potência muscular dos membros inferiores. As variáveis de aptidão aeróbia e anaeróbia relacionaram-se com menor queda do desempenho, maior taxa de golpes de perna e maior tempo médio de combate. Assim, observou-se predominância do sistema aeróbio para suprir a energia necessária para a realização do combate de judô. Além disso, maiores níveis de aptidão aeróbia e anaeróbia estão associados positivamente com o desempenho durante a luta / Considering that judo combat can last from a few seconds to up to more than 5 minutes, characterization of the physiological demands of combat in different time frames, and the relationship of these responses to an athlete\'s level of aerobic and anaerobic fitness is relevant to improving training methods. Thus, the objective of the present study was to describe the physiological demands of judo combat. Twelve judo athletes performed 10 experimental sessions. In the first and second sessions, four physical tests to characterize the aerobic and anaerobic fitness of the upper and lower limbs were performed. In the other sessions, the athletes performed 15 judo combat (involving 3 conditions x 5 durations of time: 1, 2, 3, 4 and 5 minutes) randomly determined, against the same opponent, on different days and blinded for time duration. In one condition, the athletes simulated actual combat. In the second condition, the athletes fought while using a gas analyzer to measure oxygen consumption in order to estimate the contribution of the energy systems. In this condition some motion adjustments were imposed. To verify if the use of the gas analyzer modified the responses obtained, in the third condition the athletes fought with the same adjustments, but did not use the equipment. These combat periods were divided into 8 sessions with two different conditions, separated by an interval of 60 minutes. The physiological, perceptual, performance, time-motion, and technical action responses were quantified in all matches. The comparison of the dependent variables was performed with an analysis of mixed models for repeated measures, followed by a post hoc Bonferroni. The associations between aerobic and anaerobic fitness to combat variables were verified using Pearson\'s correlation. For all significant pairwise comparisons the effect size (d Cohen) was calculated. A 5% level of significance was adopted for all analyses. The main results showed an increase in aerobic contribution with a concomitant reduction of the anaerobic contribution in the course of combat, given that the aerobic contribution was greater than the anaerobic contribution from the first minute of combat. The lactic anaerobic system contributed to the smaller proportion of energy cost in judo combat. The increment in rate of the physiological and perceptual responses per minute of combat decreased throughout the course of the combat, with the highest changes occurring at the beginning of combat, which suggest that judo athletes seem to modulate their effort. In the course of combat, maintenance of the average time of effort and actions occurred, but there was an increase in the average time of pause. After the combat, a decline in the dynamic strength endurance of the upper limbs was observed, while maximal isometric handgrip strength was maintained, and improvement of muscle power in the lower limbs was noted. The aerobic and anaerobic fitness variables were associated with lower fall performance, higher rate of leg attacks and a higher average time of standing combat. Thus, a predominance of the aerobic system in supplying the energy needed for the realization of judo combat was observed. In addition, higher levels of aerobic and anaerobic fitness are positively associated with performance during the combat

Le mode de vie des pays industrialisés, basé sur le consumérisme, est considéré comme l’un des principaux moteurs de l’usage de ressources et de la dégradation de l’environnement global. Sa substitution par d’autres modes de vie constitue l’une des clés pour bâtir un futur soutenable, d’autant qu’il tend à être imité dans les pays émergents et en développement. Pourtant, la question de la transition des modes de vie a été jusqu’à présent relativement peu investie par les politiques publiques, y compris par celles qui visent à répondre aux enjeux de la transition énergétique et de l’atténuation du changement climatique. C’est dans le but d’encourager les parties prenantes de ces enjeux à se saisir de cette question que nos recherches ont été initiées. Pour cela, nous avons choisi de nous concentrer sur la démarche prospective, qui est l’un des outils d’aide à la décision privilégiés pour éclairer les politiques de l’énergie et du changement climatique dont les enjeux portent sur les moyen et long termes. Nous avons constaté que la question était jusqu’à présent très partiellement abordée dans la plupart des exercices de prospective énergie-climat. Ce constat tient en partie au fait que, alors que la pratique actuelle accorde une place importante à la modélisation, le formalisme des modèles utilisés n’a bien souvent pas été pensé pour traiter de cette notion multidimensionnelle. Dans ce contexte, notre contribution porte sur les plans conceptuel et méthodologique. Nous avons dans un premier temps défini un cadre conceptuel pour aborder la notion de mode de vie et clarifier son rôle dans le système énergétique. Dans un second temps, nous avons proposé une approche par la modélisation destinée à simuler des scénarios d’évolution des modes de vie à l’échelle de la France. Cette approche formelle, dont le développement a constitué le cœur de nos recherches, permet de quantifier la demande en logements, la demande en mobilité et la demande en biens et services qui résultent de ces scénarios et définissent la structure des usages de l’énergie. La mise en œuvre de cette approche est illustrée dans ce manuscrit par la simulation de trois scénarios d’évolution des modes de vie. / Consumerist lifestyles in industrialized countries are considered one of the main drivers of global resource use and environment degradation. Changes in these lifestyles are therefore one of the keys to achieving a sustainable future, especially as these lifestyles also tend to be pursued by some economic classes in developing countries. Yet the lifestyles issue has only marginally been considered in public policies until now, including the ones that aimed to address the challenges of energy transition and climate change mitigation. Our research was initiated in order to encourage all parties engaging with these challenges to take into account our future lifestyles in this context. To this aim, we focused on the prospective approach. It is indeed one of the tools and processes that is most commonly used to support decision-makers on the long-term challenges raised by energy transition and tackling climate change. We found that most foresight studies did not go in depth while addressing the issue of lifestyles, especially the model-based studies. Indeed, the models generally used in these studies are not thought out to allow for proper consideration of this multidimensional issue. To answer for this, we propose a conceptual framework that allows proper understanding of the lifestyle concept and clarifies its role in the energy system. As a core contribution, we developed a modelling approach to simulate lifestyle-change scenarios for France. This formal approach allows us to quantify the demands for housing, mobility, goods and services that arises in these scenarios and defines the structure of energy uses. Three scenarios for lifestyle changes are considered in this manuscript to demonstrate implementations of the proposed approach.

L’utilisation des charges de manière active et intelligente et leur gestion optimale sont parmiles préoccupations majeures des gestionnaires, des fournisseurs, des commercialisateurs et desconsommateurs d’énergie, et constitue l’un de axes privilégies du projet smart-grid.L’objectif de cette thèse est de développer et réaliser un système de pilotage des charges desbâtiments résidentiels ou tertiaires en temps réel en utilisant des réseaux de capteurs sans fil. Lesméthodes de gestion de charge ont été développées afin de minimiser les pics de consommation,maintenir le confort thermique et minimiser le coût global de consommation. Une conception dusystème de gestion des charges en temps réel sans fil a été proposée avec la communicationstandardisée ZigBee. Des démonstrateurs basés sur la régulation adaptative des chauffages et desclimatisations d’une part et sur une méthode de délestage doux pour des cuisinières d’autre part ontété développés. Le prototype du système proposé a été réalisé et testé lors de campagnes demesures sur un appartement expérimental afin de montrer l’intérêt et les performances des méthodesproposées. Le système développé permet d’éviter l’utilisation des modèles prédictifs qui sont trèsdifficiles à identifier et à reconfigurer en cas d’ajout de nouveaux appareils électriques dans lesbâtiments contrôlés. / Load management in an active and intelligent way is one of the major concerns of distributionsystems operators, suppliers and consumers of energy, particularly in the context of the smart-gridproject.The aim of this thesis is to develop and implement a real-time energy management systembased on wireless sensor networks in buildings (residential and tertiary sector). The methods of loadmanagement have been developed to minimize peak demand, maintain thermal comfort, andminimize the cost of consumption. A concept of real-time load management using a wireless sensornetwork has been proposed, based on the ZigBee communication standard. Demonstrators ofadaptive control of heating and air conditioning and of intelligent load shedding for electrical cookershave been developed. The prototypes of the proposed systems have been built and tested on anexperimental apartment to demonstrate the usefulness and effectiveness of these methods. Thedeveloped system allows to avoid the use of predictive models that are very difficult to identify andself-reconfigure when new electrical devices are added in a building.

O conceito de cidadania tem evoluído ao longo dos anos, fonte e guardiã de direitos e deveres iguais para todos. Mas a atual educação básica, que poderia proporcionar o desenvolvimento de espírito crítico, não prepara o cidadão para decisões presentes no cotidiano. Nesse sentido, o presente trabalho se propõe a ressaltar a importância da aprendizagem sobre questões energéticas, em particular relacionadas à Eletricidade, em atenção ao desafio de conciliação de desenvolvimento humano à preservação ambiental, assim como a reunir informações e considerações que ampliem e qualifiquem a presença dessas questões na educação básica e na preparação de seus professores. Pressupostos educacionais humanistas conduzem uma análise de textos, projetos e recursos didáticos, seguida de um panorama dos problemas socioambientais, econômicos e do desenvolvimento do sistema energético brasileiro ao longo do tempo. A apresentação da atual e necessária interação interdisciplinar entre educação e preservação do meio ambiente fornece elementos para a elaboração de sugestões, no sentido de que recursos para educação básica e seus professores, especialmente do Ensino Médio, efetivamente equipem o jovem estudante em elementos para exercer sua cidadania. Levando em consideração essas preocupações, a análise dos recursos didáticos e o histórico da política energética orientam proposições e sugestões para a pretendida qualificação visando maior compreensão e participação do estudante e cidadão a respeito desse tema. / The citizenship concept evolved along the years, source and guardian of rights and duties equal for all. But the current basic school education, which could provide the social inclusion and the development of critical spirit, does not prepare the citizen for present decisions on a daily basis. On this sense, the current Paper proposes itself to emphasize the importance of the learning about energetic questions, in particular related to the Electricity, in attention to the challenge of conciliation of economic growth to the environmental preservation, as well as to collect information and considerations that broaden and qualify the presence of those questions in the basic school education and in the preparation of its professors. Presumed educational and humanists considerations lead to an analysis of texts, projects and learning resources, followed by an overview of the social-environmental issues, economical issues and of the development of the Brazilian energy system along the times. The presentation of the current and necessary interdisciplinary interaction between education and environmental preservation give elements for the elaboration of suggestions, in the sense of which resources for basic education and its professors, especially of the medium education, effectively equip the young student with elements to exercise his citizenship. Taking into consideration those concerns, the analysis of the learning resources and the historical ones of Energy Policy lead to propositions and suggestions for the desired qualification aiming a deeper understanding and a increased participation of the student and citizen about this topic.