Neste trabalho, são discutidas as características de transistores de filmes finos (TFTs) nos quais nanopartículas de óxido de zinco (ZnO) são empregadas como material ativo na camada semicondutora. O crescimento contínuo do interesse por este componente está associado à busca pelo desenvolvimento da tecnologia de dispositivos eletrônicos flexíveis, transparentes e de baixo custo. TFTs integrados com nanopartículas de ZnO são apresentados, e uma extensa rotina de caracterização elétrica transiente é realizada para avaliar como estes dispositivos se comportam e degradam ao longo do tempo. Foram medidas, ao total, 80 amostras de transistores integrados em duas configurações distintas: inverted staggered e inverted coplanar. A partir das medidas analisadas foram identificados dois grupos de comportamentos elétricos dominantes, os quais foram classificados em: efeitos abruptos e efeitos de memória. A partir dos dados coletados, foram formuladas hipóteses para modelar o comportamento típico observado. Para tanto, utiliza-se dos mecanismos de atividade de traps, de interação da camada semicondutora com o meio ambiente, de polarização de dipolos e difusão de cargas móveis no dielétrico, de formação de caminhos percolados paralelos pelas nanopartículas e de difusão de vacâncias de oxigênio e íons metálicos que podem estar associados ao comportamento elétrico observado. / In this work, the characteristics of thin-film transistors (TFTs) employing nanoparticulated zinc oxide (ZnO) as the active semiconductor channel layer are discussed. The growing interest in this component is associated to the development of low-cost, flexible and transparent electronic devices. The TFTs integrated with ZnO nanoparticles are presented and an extensive transient electrical characterization campaign was performed in order to evaluate how these devices behave and degrade over time. The measurement was performed for 80 samples of two different integration setups: inverted staggered and inverted coplanar. In the performed tests two main disturbances were identified, which were classified as abrupt and memory effects. From the collected data, hypothesis to model the observed typical behavior are formulated. Trapping activity, ambient interaction, dielectric dipoles, mobile charges, formed parallel-paths, oxygen vacancies and metallic ions diffusion are mechanisms that may be associated to the observed behavior.

abstract: This work explores how flexible electronics and display technology can be applied to develop new biomedical devices for medical, biological, and life science applications. It demonstrates how new biomedical devices can be manufactured by only modifying or personalizing the upper layers of a conventional thin film transistor (TFT) display process. This personalization was applied first to develop and demonstrate the world's largest flexible digital x-ray detector for medical and industrial imaging, and the world's first flexible ISFET pH biosensor using TFT technology. These new, flexible, digital x-ray detectors are more durable than conventional glass substrate x-ray detectors, and also can conform to the surface of the object being imaged. The new flexible ISFET pH biosensors are >10X less expensive to manufacture than comparable CMOS-based ISFETs and provide a sensing area that is orders of magnitude larger than CMOS-based ISFETs. This allows for easier integration with area intensive chemical and biological recognition material as well as allow for a larger number of unique recognition sites for low cost multiple disease and pathogen detection. The flexible x-ray detector technology was then extended to demonstrate the viability of a new technique to seamlessly combine multiple smaller flexible x-ray detectors into a single very large, ultimately human sized, composite x-ray detector for new medical imaging applications such as single-exposure, low-dose, full-body digital radiography. Also explored, is a new approach to increase the sensitivity of digital x-ray detectors by selectively disabling rows in the active matrix array that are not part of the imaged region. It was then shown how high-resolution, flexible, organic light-emitting diode display (OLED) technology can be used to selectively stimulate and/or silence small groups of neurons on the cortical surface or within the deep brain as a potential new tool to diagnose and treat, as well as understand, neurological diseases and conditions. This work also explored the viability of a new miniaturized high sensitivity fluorescence measurement-based lab-on-a-chip optical biosensor using OLED display and a-Si:H PiN photodiode active matrix array technology for point-of-care diagnosis of multiple disease or pathogen biomarkers in a low cost disposable configuration. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2014

Organic thin film transistors (OTFT) are a key active devices of future organic electronic circuits. The biggest advantages of organic electronics are the potential for cheep production and the enabling of new applications for light, bendable or transparent devices. These benefits are offered by a wide spectrum of various molecules and polymers that are optimized for different purpose. In this work, several interesting organic semiconductors are compared as well as transistor geometries and processing steps. In a cooperation with an industrial partner, test series of transistors are produced that are intensively characterized and used as a basis for later device simulation. Therefore, among others 4-point-probe measurements are used for a potential mapping of the transistor channel and via transfer line method the contact resistance is measured in a temperature range between 173 and 353 K. From later comparison with the simulation models, it appears that the geometrical resistance is actually more important for the transistor performance than the resistance of charge-carrier injection at the electrodes. The charge-carrier mobility is detailed evaluated and discussed. Within the observed temperature range a Arrhenius-like thermal activation of the charge- carrier transport is determined with an activation energy of 170 meV. Furthermore, a dependence of the electric field-strength of a Poole-Frenkel type is found with a Poole-Frenkel factor of about 4.9 × 10E−4 (V/m) −0.5 that is especially important for transistors with small channel length. With these two considerations, already a good agreement between device simulation and measurement data is reached. In a detailed discussion of the dependence on the charge-carrier density and from comparison with established the charge-carrier mobility models, an exponential density of states could be estimated for the organic semiconductor. However, reliability of OTFTs remains one of the most challenging hurdles to be understood and resolved for broad commercial applications. In particular, bias-stress is identified as the key instability under operation for numerous OTFT devices and interfaces. In this work, a novel approach is presented that allows controlling and significantly alleviating the bias-stress effect by using molecular doping at low concentrations. For pentacene as semiconductor and SiO2 as gate oxide, we are able to reduce the time constant of degradation by three orders of magnitude. The effect of molecular doping on the bias-stress is explained in terms of the shift of Fermi level and, thus, exponentially reduced proton generation at the pentacene/oxide interface. For transistors prepared in cooperation with the industrial partner, a second effect is observed that can be explained by a model considering a ferroelectric process in the dielectric and counteracts the bias-stress behavior.

Nanocrystalline silicon (nc-Si:H) is a promising material for Thin-Film Transistors (TFTs) offering potentially higher mobilities and improved stability over hydrogenated amorphous silicon (a-Si:H). The slow growth rate of nc-Si:H can be overcome by using pulsed Plasma-Enhanced Chemical Vapour Deposition (PECVD). Pulsed PECVD also reduces powder particle formation in the plasma and provides added degrees of freedom for process optimization. Unlike high frequency PECVD, pulsed PECVD can be scaled to deposit films over large areas with no reduction in performance. For this thesis, silicon thin films were deposited by the pulsed PECVD technique at a temperature of 150 ??C and TFTs were made using this material. Radio Frequency (RF) power and silane (SiH₄) flow rate were varied in order to study the effect of different levels of crystallinity on the film. Raman spectroscopy, Atomic Force Microscope (AFM), X-Ray Diffraction (XRD), electrical conductivity, Hall mobility, optical band gap, and stability under light-soaking were measured using films of two different thicknesses, 50 nm and 300 nm. From the Raman data we see that the 50 nm films deposited with high hydrogen dilution are mostly amorphous, indicating the presence of a thick incubation layer. The 300nm samples deposited with hydrogen dilution, on the other hand, showed very high crystallinity and conductivity, except for 300-2 which was surprisingly, mostly amorphous. AFM and XRD measurements were also performed to confirm the Raman data and get an estimate for the crystallite grain size in the 300 nm samples. The conductivity was measured for all films, and the Hall mobility and carrier concentration was measured for one of the 300 nm films. The thin samples which are mostly amorphous show low conductivity whereas the thick high crystallinity films show high conductivity, and n-type behaviour possibly due to oxygen doping. The optical gap was also measured using Ultra Violet (UV) light and results indicate the possible presence of small crystallites in the 50 nm films. The conductivity's stability under light-soaking was measured to observe the material's susceptibility to degradation, and the 300 nm with high crystallinity were much more stable than the a-Si:H films. All the results of these measurements varied depending on the film and these results are discussed. Bottom-gate TFTs were fabricated using a pulsed PECVD channel layer and an amorphous silicon nitride (a-SiN:H) gate dielectric. The extracted parameters of one of the best TFTs are <i>&mu;_sat</i> &le; 0. 38 cm² V^-1 s^-1, <i>V_t,sat</i> &ge; 7. 3 V, <i>I_on/off</i> > 10⁶, and <i>S</i> < 1 V/decade. These parameters were extracted semi-automatically from the basic Field-Effect Transistor (FET) model using a computer program. Extraction using a more complicated model yielded similar results for mobility and threshold voltage but also gave a large power parameter <i>&alpha;</i> of 2. 31 and conduction band tail slope of 30 meV. The TFT performance and material properties are presented and discussed. On this first attempt at fabricating TFTs using a nc-Si:H channel layer deposited by pulsed PECVD, results were obtained which are consistent with results for low temperature a-Si:H TFTs and previous pulsed PECVD TFTs. The channel layer was mostly amorphous and non-crystalline, possibly due to the amorphous substrate or insufficient hydrogen dilution in the plasma. The 300 nm films showed, however, that high crystallinity material deposited directly on glass can easily be obtained, and this material showed less degradation under light-soaking than the purely amorphous counterpart. Pulsed PECVD is a promising technique for the growth of nc-Si:H and with further materials development and process optimization for TFTs, it may prove to be useful for the growth of high-quality nc-Si:H TFT channel layers.

A range of small molecules of interest for use in organic semiconductor devices were studied computationally. Trends in geometry, absorption spectra, molecular orbitals, electrostatic potentials, reorganisation energies were studied. Results suggest that, as with acenes, the performance of non-linear cata-condensed polyaromatic hydrocarbons improves as number of fused benzene rings increases. The torsion in these molecules did not appear to have a large impact on the conjugation across the core and little effect on the absorption spectra, although it did affect the reorganisation energies on which charge mobilities depend. Computational studies of mobilities of anthradithiophene molecules were broadly able to reproduce trends seen experimentally and emphasised the importance of crystal morphology. Experimental work was also carried out to search for cocrystals between anthradithiophene derivatives. Many examples were found with some mixtures forming different cocrystals at different mixture ratios. These results were rationalised by a computational study that showed molecules which had a similar binding energy were more likely to be able to form cocrystals. Cocrystal devices were fabricated and 3 out of 7 showed a larger mobility than devices made out of its constituent materials alone. The best of these had a mobility 65% higher than a device made out of the constituent material with the largest mobility. An energy decomposition analysis was carried out on a novel thallophilic system, a complex of thallium with a neutral β-triketimine ligand which was found to form dimers with close Tl-Tl interactions. Calculations show the electrostatic interaction to be repulsive for the dimer with no counter ions, but attractive when 3,5-bistrifluoromethylphenyl borate counter ions are included. This suggests the metallophilic interaction is counter ion-mediated, requiring the anions to provide favourable electrostatics, even in the case of spatially diffuse and distant counter ions such used here. To enable the studies described here software was written for simulating absorption spectra. An implementation into the Gaussian Suite of programs of an energy decomposition scheme and its extension to include an empirical dispersion correction was also carried out.

The characterization and fabrication of active matrix thin film transistors (TFTs) has been studied for an addressable microfluidic electrowetting channel device as application. A new transparent semiconductor material, Amorphous Indium Gallium Zinc Oxide (a-IGZO), is used for TFT, which shows high electrical performance rather than amorphous silicon based TFT; higher mobility and even higher transparency. The purpose of this dissertation is to optimize each TFT process including the optimization of a-IGZO properties to achieve robust device for application. To minimize hysteresis of TFT curves, the gate dielectric is discussed extensively in this dissertation. By optimizing gas ratio of NH3SiH4, it is found that the TFT with NH3 rich SiNx gate dielectric deposited with NH3/SiH4 =5.1 and stoichiometric SiO2 demonstrates best condition to reduce hysteresis. a-IGZO films is investigated as a function of power and substrate bias effect which affects to electrical performance; the higher power and substrate bias increase the carrier density in the film and mainly cause threshold voltage(VT) to shift in the negative gate voltage direction and mobility to increase, respectively. In addition, the powerful method to estimate the electrical properties of a-IGZO is proposed by calculating O2 and IGZO flux during sputtering in which the incorporation ratio with O2/IGZO ≈1 demonstrates the optimized a-IGZO film for TFT. It is confirmed that both physical and chemical adsorption affects the electrical property of a-IGZO channel by studying TFT-IV characteristics with different pressure and analyzing X-ray photoelectron spectroscopy (XPS), which mainly affects the VT instability. The sputtered SiO2 passivation shows better electrical performance. To achieve electrically compatible (lower back channel current) a-IGZO film to SiO2 sputter passivated device, a-IGZO TFTs require oxygen rich a-IGZO back channel by employing two step a-IGZO deposition process (2nd 10nm a-IGZO with PO2 = 1.5mTorr on 1st 40nm a-IGZO with PO2=1mTor). Electrowetting microfluidic channel device as application using a-IGZO TFTs is studied by doing preliminary test. The electrowetting channel test using polymer post device platform is candidate for addressable electrowetting microfluidic channel device driven by active matrix type a-IGZO TFT.

The outstanding electrical and mechanical properties of single-walled carbon nanotubes (SWCNTs) may offer solutions to realizing high-mobility and high-bendability thin-film transistors (TFTs) for the emerging flexible electronics. This thesis aims to develop low-cost ink-jet printing techniques for high-performance TFTs based on pristine SWCNTs. The main challenge of this work is to suppress the effects of “metallic SWCNT contamination” and improve the device electrical performance. To this end, this thesis entails a balance between experiments and simulations.   First, TFTs with low-density SWCNTs in the channel region are fabricated by utilizing standard silicon technology. Their electrical performance is investigated in terms of throughput, transfer characteristics, dimensional scaling and dependence on electrode metals. The demonstrated insensitivity of electrical performance to the electrode metals lifts constrains on choosing metal inks for ink-jet printing.   Second, Monte Carlo models on the basis of percolation theory have been established, and high-efficiency algorithms have been proposed for investigations of large-size stick systems in order to facilitate studies of TFTs with channel length up to 1000 times that of the SWCNTs. The Monte Carlo simulations have led to fundamental understanding on stick percolation, including high-precision percolation threshold, universal finite-size scaling function, and dependence of critical conductivity exponents on assignment of component resistance. They have further generated understanding of practical issues regarding heterogeneous percolation systems and the doping effects in SWCNT TFTs.   Third, Monte Carlo simulations are conducted to explore new device structures for performance improvement of SWCNT TFTs. In particular, a novel device structure featuring composite SWCNT networks in the channel is predicted by the simulation and subsequently confirmed experimentally by another research group. Through Monte Carlo simulations, the compatibility of previously-proposed long-strip-channel SWCNT TFTs with ink-jet printing has also been demonstrated.   Finally, relatively sophisticated ink-jet printing techniques have been developed for SWCNT TFTs with long-strip channels. This research spans from SWCNT ink formulation to device design and fabrication. SWCNT TFTs are finally ink-jet printed on both silicon wafers and flexible Kapton substrates with fairly high electrical performance. / QC 20100910

This work extends the technology of amorphous silicon (a-Si) thin film transistors (TFTs) from traditional switching applications to on-pixel signal amplification for large area digital imaging and in particular, is aimed towards enabling emerging low noise, high resolution and high frame rate medical diagnostic imaging modalities such as digital tomosynthesis. A two transistor (2T) pixel amplifier circuit based on a novel charge-gate thin film transistor (TFT) device architecture is introduced to shrink the TFT based pixel readout circuit size and complexity and thus, improve the imaging array resolution and reliability of the TFT fabrication process. The high resolution pixel amplifier results in improved electrical performance such as on-pixel amplification gain, input referred noise and faster readouts. In this research, a charge-gated TFT that operates as both a switched amplifier and driver is used to replace two transistors (the addressing switch and the amplifier transistor) of previously reported three transistor (3T) APS pixel circuits.. In addition to enabling smaller pixels, the proposed 2T pixel amplifier results in better signal-to-noise (SNR) by removing the large flicker noise source associated with the switched TFT and increased pixel transconductance gain since the large ON-state resistance of the switched TFT is removed from the source of the amplifier TFT. Alternate configurations of 2T APS architectures based on source or drain switched TFTs are also investigated, compared, and contrasted to the gate switched architecture using charge-gated TFT. A new driving scheme based on multiple row resetting is introduced which combined with the on-pixel gain of the APS, offers considerable improvements in imaging frame rates beyond those feasible for PPS based pixels. The novel developed 2T APS architectures is implemented in single pixel test structures and in 88 pixel test arrays with a pixel pitch of 100 µm. The devices were fabricated using an in-house developed top-gate TFT fabrication process. Measured characteristics of the test devices confirm the performance expectations of the 2T architecture design. Based on parameters extracted from fabricated TFTs, the input referred noise is calculated, and the instability in pixel transconductance gain over prolonged operation tine is projected for different imaging frame rates. 2T APS test arrays were packaged and integrated with an amorphous selenium (a-Se) direct x-ray detector, and the x-ray response of the a-Se detector integrated with the novel readout circuit was evaluated. The special features of the APS such as non-destructive readout and voltage programmable on-pixel gain control are verified. The research presented in this thesis extends amorphous silicon pixel amplifier technology into the area of high density pixel arrays such as large area medical X-ray imagers for digital mammography tomosynthesis. It underscores novel device and circuit design as an effective method of overcoming the inherent shortcomings of the a-Si material . Although the developed device and circuit ideas were implemented and tested using a-Si TFTs, the scope of the device and circuit designs is not limited to amorphous silicon technology and has the potential to be applied to more mainstream technologies, for example, in CMOS active pixel sensor (APS) based digital cameras.

This thesis examines strategies to exploit existing materials and techniques to advance organic thin film transistor (OTFT) technology in device performance, device manufacture, and device integration. To enhance device performance, optimization of plasma enhanced chemical vapor deposited (PECVD) gate dielectric thin film and investigation of interface engineering methodologies are explored. To advance device manufacture, OTFT fabrication strategies are developed to enable organic circuit integration. Progress in device integration is achieved through demonstration of OTFT integration into functional circuits for applications such as active-matrix displays and radio frequency identification (RFID) tags. OTFT integration schemes featuring a tailored OTFT-compatible photolithography process and a hybrid photolithography-inkjet printing process are developed. They enable the fabrication of fully-patterned and fully-encapsulated OTFTs and circuits. Research on improving device performance of bottom-gate bottom-contact poly(3,3'''-dialkyl-quarter-thiophene) (PQT-12) OTFTs on PECVD silicon nitride (SiNx) gate dielectric leads to the following key conclusions: (a) increasing silicon content in SiNx gate dielectric leads to enhancement in field-effect mobility and on/off current ratio; (b) surface treatment of SiNx gate dielectric with a combination of O2 plasma and octyltrichlorosilane (OTS) self-assembled monolayer (SAM) delivers the best OTFT performance; (c) an optimal O2 plasma treatment duration exists for attaining highest field-effect mobility and is linked to a “turn-around” effect; and (d) surface treatment of the gold (Au) source/drain contacts by 1-octanethiol SAM limits mobility and should be omitted. There is a strong correlation between the electrical characteristics and the interfacial characteristics of OTFTs. In particular, the device mobility is influenced by the interplay of various interfacial mechanisms, including surface energy, surface roughness, and chemical composition. Finally, the collective knowledge from these investigations facilitates the integration of OTFTs into organic circuits, which is expected to contribute to the development of new generation of all-organic displays for communication devices and other pertinent applications. A major outcome of this work is that it provides an economical means for organic transistor and circuit integration, by enabling use of the well-established PECVD infrastructure, yet not compromising the performance of electronics.

Nanocrystalline silicon (nc-Si:H) is a promising material for Thin-Film Transistors (TFTs) offering potentially higher mobilities and improved stability over hydrogenated amorphous silicon (a-Si:H). The slow growth rate of nc-Si:H can be overcome by using pulsed Plasma-Enhanced Chemical Vapour Deposition (PECVD). Pulsed PECVD also reduces powder particle formation in the plasma and provides added degrees of freedom for process optimization. Unlike high frequency PECVD, pulsed PECVD can be scaled to deposit films over large areas with no reduction in performance. For this thesis, silicon thin films were deposited by the pulsed PECVD technique at a temperature of 150 °C and TFTs were made using this material. Radio Frequency (RF) power and silane (SiH₄) flow rate were varied in order to study the effect of different levels of crystallinity on the film. Raman spectroscopy, Atomic Force Microscope (AFM), X-Ray Diffraction (XRD), electrical conductivity, Hall mobility, optical band gap, and stability under light-soaking were measured using films of two different thicknesses, 50 nm and 300 nm. From the Raman data we see that the 50 nm films deposited with high hydrogen dilution are mostly amorphous, indicating the presence of a thick incubation layer. The 300nm samples deposited with hydrogen dilution, on the other hand, showed very high crystallinity and conductivity, except for 300-2 which was surprisingly, mostly amorphous. AFM and XRD measurements were also performed to confirm the Raman data and get an estimate for the crystallite grain size in the 300 nm samples. The conductivity was measured for all films, and the Hall mobility and carrier concentration was measured for one of the 300 nm films. The thin samples which are mostly amorphous show low conductivity whereas the thick high crystallinity films show high conductivity, and n-type behaviour possibly due to oxygen doping. The optical gap was also measured using Ultra Violet (UV) light and results indicate the possible presence of small crystallites in the 50 nm films. The conductivity's stability under light-soaking was measured to observe the material's susceptibility to degradation, and the 300 nm with high crystallinity were much more stable than the a-Si:H films. All the results of these measurements varied depending on the film and these results are discussed. Bottom-gate TFTs were fabricated using a pulsed PECVD channel layer and an amorphous silicon nitride (a-SiN:H) gate dielectric. The extracted parameters of one of the best TFTs are <i>&mu;_sat</i> &le; 0. 38 cm² V^-1 s^-1, <i>V_t,sat</i> &ge; 7. 3 V, <i>I_on/off</i> > 10⁶, and <i>S</i> < 1 V/decade. These parameters were extracted semi-automatically from the basic Field-Effect Transistor (FET) model using a computer program. Extraction using a more complicated model yielded similar results for mobility and threshold voltage but also gave a large power parameter <i>&alpha;</i> of 2. 31 and conduction band tail slope of 30 meV. The TFT performance and material properties are presented and discussed. On this first attempt at fabricating TFTs using a nc-Si:H channel layer deposited by pulsed PECVD, results were obtained which are consistent with results for low temperature a-Si:H TFTs and previous pulsed PECVD TFTs. The channel layer was mostly amorphous and non-crystalline, possibly due to the amorphous substrate or insufficient hydrogen dilution in the plasma. The 300 nm films showed, however, that high crystallinity material deposited directly on glass can easily be obtained, and this material showed less degradation under light-soaking than the purely amorphous counterpart. Pulsed PECVD is a promising technique for the growth of nc-Si:H and with further materials development and process optimization for TFTs, it may prove to be useful for the growth of high-quality nc-Si:H TFT channel layers.