No description available.

No description available.

The present work aims at enhancing the external quantum efficiencies of ultra-violet (UV) sensitive photodetectors (PDs) and light emitting diodes (LEDs)for any light polarization. Deep UV solid state devices are made out of AlGaN or MgZnO and their performances suffer from the high resistivity of their p-doped regions. They require transparent p-contacts; yet the most commonly used transparent contacts have low transmission in the UV: indium tin oxide (ITO) and nickel-gold (Ni/Au 5/5 nms) transmit less than 50% and 30% respectively at 300 nm. Here we investigate the use of surface plasmons (SPs) to design transparent p-contacts for AlGaN devices in the deep UV region of the spectrum. The appeal of using surface plasmon coupling arose from the local electromagnetic field enhancement near the metal surface as well as the increase in interaction time between the field and semiconductor if placed on top of a semiconductor. An in/out-coupling mechanism is achieved by using a grating consisting of two perpendicularly oriented sets of parallel aluminum lines with periods as low as 250 nm. The incident light is first coupled into SPs at the air/aluminum interface which then re-radiate at the aluminum/AlGaN interface and the photons energy is transferred to SP polaritons (SPPs) and back to photons. High transmission can be achieved not only at normal incidence but for a wider range of incident angles. iv A finite difference time domain (FDTD) package from R-Soft was used to simulate and design such aluminum gratings with transparency as high as 100% with tunable peak wavelength, bandwidth and angular acceptance. A rigorous coupled wave analysis (RCWA) was developed in Matlab to validate the FDTD results. The high UV transparency meshes were then fabricated using an e-beam assisted lithography lift-off process. Their electrical and optical properties were investigated. The electrical characterization was very encouraging; the sheet resistances of these meshes were lower than those of the conventionally used transparent contacts. The optical transmissions were lower than expected and the causes for the lower measurements have been investigated. The aluminum oxidation, the large metal grain size and the line edge roughness were identified as the main factors of inconsistency and solutions are proposed to improve these shortcomings. The effect of aluminum oxidation was calculated and the passivation of aluminum with SiO2 was evaluated as a solution. A cold deposition of aluminum reduced the aluminum grain size from 60 nm to 20 nm and the roughness from 5 nm to 0.5 nm. Furthermore, replacing the conventional lift-off process by a dry back-etch process led to much smoother metal line edges and much high optical transparency. The optical measurements were consistent with the simulations. Therefore, reduced roughness and smooth metal line edges were found to be especially critical considerations for deep UV application of the meshes.

The Cardiac Rhythm Management Division of St. Jude Medical specializes in the development of implantable cardioverter defibrillators that improve the quality of life for patients diagnosed with a variety of cardiac arrhythmias, especially for patients prone to sudden cardiac death. With the goal to improve detection of cardiac arrhythmias, this study explored the value in time-frequency analysis of intracardiac electrogram in four steps. The first two steps characterized, in the frequency domain, the waveforms that construct the cardiac cycle. The third step developed a new algorithm that putatively provides the least computationally expensive way to identifying cardiac waveforms in the frequency domain. Lastly, this novel approach to analyzing intracardiac electrogram was compared to a threshold crossing algorithm that strictly operates in the time domain and that is currently utilized by St. Jude Medical. The new algorithm demonstrated an equally effective method in identifying the QRS complex on the ventricular channel. The next steps in pursing time-frequency analysis of intracardiac electrogram include implementing the new algorithm on a testing platform that emulates the latest implantable cardioverter defibrillator manufactured by St. Jude Medical and pursuing a similar algorithm that can be employed on the atrial channel.

yes / There is an increasing need for accurate models describing the electrical behaviour of individual biological cells exposed to electromagnetic fields. In this area of solving linear problem, the most frequently used technique for computing the EM field is the Finite-Difference Time-Domain (FDTD) method. When modelling objects that are small compared with the wavelength, for example biological cells at radio frequencies, the standard Finite-Difference Time-Domain (FDTD) method requires extremely small time-step sizes, which may lead to excessive computation times. The problem can be overcome by implementing a quasi-static approximate version of FDTD, based on transferring the working frequency to a higher frequency and scaling back to the frequency of interest after the field has been computed. An approach to modeling and analysis of biological cells, incorporating the Hodgkin and Huxley membrane model, is presented here. Since the external medium of the biological cell is lossy material, a modified Berenger absorbing boundary condition is used to truncate the computation grid. Linear assemblages of cells are investigated and then Floquet periodic boundary conditions are imposed to imitate the effect of periodic replication of the assemblages. Thus, the analysis of a large structure of cells is made more computationally efficient than the modeling of the entire structure. The total fields of the simulated structures are shown to give reasonable and stable results at 900MHz, 1800MHz and 2450MHz. This method will facilitate deeper investigation of the phenomena in the interaction between EM fields and biological systems. Moreover, the nonlinear response of biological cell exposed to a 0.9GHz signal was discussed on observing the second harmonic at 1.8GHz. In this, an electrical circuit model has been proposed to calibrate the performance of nonlinear RF energy conversion inside a high quality factor resonant cavity with known nonlinear device. Meanwhile, the first and second harmonic responses of the cavity due to the loading of the cavity with the lossy material will also be demonstrated. The results from proposed mathematical model, give good indication of the input power required to detect the weakly effects of the second harmonic signal prior to perform the measurement. Hence, this proposed mathematical model will assist to determine how sensitivity of the second harmonic signal can be detected by placing the required specific input power.

The aim of this study is to analysis, investigate and find out the solutions for the problems associated with the implementations of antennas RFID Reader and Tag for various applications. In particular, the efficiency of the RFID reader antenna and the detection range of the RFID tag antenna, subject to a small and compact antenna¿s design configuration have been studied. The present work has been addressed directly to reduce the cost, size and increase the detection range and communication reliability of the RFID framework antennas. Furthermore, the modelling concept of RFID passive tags mounted on various materials including the novel design of RFID reader antenna using Genetic Algorithm (GA) are considered and discussed to maintain reliable and efficient antenna radiation performances. The main benefit of applying GA is to provide fast, accurate and reliable solutions of antenna¿s structure. Therefore, the GA has been successfully employed to design examples: meander-line, two linear cross elements and compact Helical- Spiral antennas. In addition, a hybrid method to model the human body interaction with RFID tag antenna operating at 900MHz has been studied. The near field distribution and the radiation pattern together with the statistical distribution of the radiation efficiency and the absorbed power in terms of cumulative distribution functions for different orientation and location of RFID¿s tag antenna on the human body have been demonstrated. Several tag antennas wi th symmetrical and unsymmetrical structure configurations operating in the European UHF band 850-950 MHz have been fabricated and tested. . The measured and simulated results have been found to be in a good agreement with reasonable impedance matching to the typical input impedance of an RFID integrated circuit chip and nominal power gain and radiation patterns.

Dealing with the electromagnetic issue might bring a sort of discontinuous and nondifferentiable regions. Thus, it is of great interest to implement an appropriate optimisation approach, which can preserve the computational resources and come up with a global optimum. While not being trapped in local optima, as well as the feasibility to overcome some other matters such as nonlinear and phenomena of discontinuous with a large number of variables. Problems such as lengthy computation time, constraints put forward for antenna requirements and demand for large computer memory, are very common in the analysis due to the increased interests in tackling high-scale, more complex and higher-dimensional problems. On the other side, demands for even more accurate results always expand constantly. In the context of this statement, it is very important to find out how the recently developed optimization roles can contribute to the solution of the aforementioned problems. Thereafter, the key goals of this work are to model, study and design low profile antennas for wireless and mobile communications applications using optimization process over a computational electromagnetics numerical solution. The numerical solution method could be performed over one or hybrid methods subjective to the design antenna requirements and its environment. Firstly, the thesis presents the design and modelling concept of small uni-planer Ultra- Wideband antenna. The fitness functions and the geometrical antenna elements required for such design are considered. Two antennas are designed, implemented and measured. The computed and measured outcomes are found in reasonable agreement. Secondly, the work is also addressed on how the resonance modes of microstrip patches could be performed using the method of Moments. Results have been shown on how the modes could be adjusted using MoM. Finally, the design implications of balanced structure for mobile handsets covering LTE standards 698-748 MHz and 2500-2690 MHz are explored through using firefly algorithm method. The optimised balanced antenna exhibits reasonable matching performance including near-omnidirectional radiations over the dual desirable operating bands with reduced EMF, which leads to a great immunity improvement towards the hand-held. / General Secretariat of Education and Scientific Research Libya

This thesis focuses on improving the performance of the THz time-domain spectroscopy system using second-order nonlinear crystals for THz generation and detection in terms of bandwidth, sensitivity, and THz field strength. The theories for the THz generation based on optical rectification and detection technique, electro-optical sampling, based on Pockels effect are introduced in Chapter 2. In Chapter 3, some experiments are presented to characterize the performances of the THz system based on a 180 fs Yb:KGW femtosecond laser amplifier operating at 1035 nm. The Yb-based femtosecond laser is becoming increasingly popular due to its robustness, high repetition rate, and high average power. However, the NIR bandwidth of these femtosecond lasers is limited by the gain bandwidth of the gain medium, and achieving pulse durations shorter than 180 fs is challenging. Consequently, the full bandwidth of THz time-domain spectroscopy systems is constrained by such laser systems. In order to broaden the THz bandwidth of such THz time-domain spectroscopy systems, our work in Chapter 4 combines the Yb:KGW femtosecond laser amplifier with an argon-filled hollow-core photonic crystal fiber pulse shaper to spectrally broaden the near-infrared pulses from 3.5 to 8.7 THz, increasing the measured THz bandwidth correspondingly from 2.3 THz to 4.5 THz. This is one of the first works to have broadband THz system based on Yb-based femtosecond lasers in the year of 2018. In Chapter 5, the tilted-pulse-front phase matching in the THz generation and detection scheme is demonstrated using the same surface-etched phase gratings on the front surfaces of the 2 mm-thick GaP generation and detection crystals. This scheme overcomes the THz generation and detection bandwidth limit of thick crystals imposed by the traditional collinear phase matching, while allowing the long nonlinear interaction length. This results in a THz spectral range from 0.1 to 6.5 THz with a peak at 3 THz and a peak dynamic range of 90 dB. In the range between 1.1 and 4.3 THz, the system dynamic range exceeds 80 dB. Based on this contact grating-based THz generation, the next step involves generating high-field THz above 2 THz. For high-field THz generation, the most renowned technique is the tilted-pulse-front technique, which generates high-field THz below 2 THz in a LiNbO₃ crystal. Most nonlinear optics experiments in the THz regime rely on such THz sources. To generate high-field THz above 2 THz, one promising candidate is organic THz crystals. However, most organic crystals require a pump laser with a wavelength exceeding 1200 nm, necessitating a more complex laser system. Additionally, the low damage threshold of these crystals are susceptible to compromise the stability of the measurements. Other techniques, such as air plasma and metallic spintronics, can generate ultra-broadband high-field THz from 0.1 to 30 THz, but the pulse energy within certain frequency windows is relatively low, rendering these THz sources less effective for nonlinearly driving specific optical transitions. On the other hand, semiconductor crystals as THz generation crystals, have a high damage threshold and can achieve good phase matching at wavelength around 800 or 1000 nm. In Chapter 6, high-field THz generation with a peak field of 303 kV/cm and a spectral peak at 2.6 THz is achieved with a more homogenous grating on the surface of a 1 mm-thick GaP generation crystal in a configuration collimating the near-infrared generation beam with a pulse energy of 0.57 mJ onto the generation crystal. The experiments also show that the system operates significantly below the GaP damage threshold and THz generation saturation regime, indicating that the peak THz field strength can approach 1 MV/cm, with a 5 mJ near-infrared generation pulse. This is the first high-field THz source based on semiconductor crystals capable of generating high-field THz above 2 THz. With such a THz source, we can conduct nonlinear optics experiments above 2 THz, including the study of phonon-assisted nonlinearities, coherent control of Bose-Einstein condensation of excitons and polaritons in semiconductor cavities, and saturable absorption in molecular gases.

The main objective of this research is to model and analyse complex electromagnetic problems by means of a new hybridised computational technique combining the frequency domain Method of Moments (MoM), Finite-Difference Time-Domain (FDTD) method and a subgridded Finite-Difference Time-Domain (SGFDTD) method. This facilitates a significant advance in the ability to predict electromagnetic absorption in inhomogeneous, anisotropic and lossy dielectric materials irradiated by geometrically intricate sources. The Method of Moments modelling employed a two-dimensional electric surface patch integral formulation solved by independent linear basis function methods in the circumferential and axial directions of the antenna wires. A similar orthogonal basis function is used on the end surface and appropriate attachments with the wire surface are employed to satisfy the requirements of current continuity. The surface current distributions on structures which may include closely spaced parallel wires, such as dipoles, loops and helical antennas are computed. The results are found to be stable and showed good agreement with less comprehensive earlier work by others. The work also investigated the interaction between overhead high voltage transmission lines and underground utility pipelines using the FDTD technique for the whole structure, combined with a subgridding method at points of interest, particularly the pipeline. The induced fields above the pipeline are investigated and analysed. FDTD is based on the solution of Maxwell¿s equations in differential form. It is very useful for modelling complex, inhomogeneous structures. Problems arise when open-region geometries are modelled. However, the Perfectly Matched Layer (PML) concept has been employed to circumvent this difficulty. The establishment of edge elements has greatly improved the performance of this method and the computational burden due to huge numbers of time steps, in the order of tens of millions, has been eased to tens of thousands by employing quasi-static methods. This thesis also illustrates the principle of the equivalent surface boundary employed close to the antenna for MoM-FDTD-SGFDTD hybridisation. It depicts the advantage of using hybrid techniques due to their ability to analyse a system of multiple discrete regions by employing the principle of equivalent sources to excite the coupling surfaces. The method has been applied for modelling human body interaction with a short range RFID antenna to investigate and analyse the near field and far field radiation pattern for which the cumulative distribution function of antenna radiation efficiency is presented. The field distributions of the simulated structures show reasonable and stable results at 900 MHz. This method facilitates deeper investigation of the phenomena in the interaction between electromagnetic fields and human tissues. / Ministry of Higher Education Malaysia and Universiti Tun Hussein Onn Malaysia (UTHM)

No description available.