<p>Today's radio frequency receivers for digital wireless communication are getting more and more complex. A single receiver unit should support multiple bands, have a wide bandwidth, be flexible and show good performance. To fulfil these requirements, new receiver architectures have to be developed and used. One possible alternative is the RF undersampling architecture. </p><p>This thesis evaluates the RF undersampling architecture, which make use of an undersampling track-and-hold circuit with very wide bandwidth to perform direct sampling of the RF carrier before the analogue-to-digital converter. The architecture’s main advantages and drawbacks are identified and analyzed. Also, techniques and improvements to solve or reduce the main problems of the RF undersampling receiver are proposed.</p>

Modern communication systems require higher data rates which have increased thedemand for high speed transceivers. For a system to work efficiently, all blocks ofthat system should be fast. It can be seen that analog interfaces are the main bottleneckin whole system in terms of speed and power. This fact has led researchersto develop high speed analog to digital converters (ADCs) with low power consumption.Among all the ADCs, flash ADC is the best choice for faster data conversion becauseof its parallel structure. This thesis work describes the design of such a highspeed and low power flash ADC for analog front end (AFE) of a transceiver. Ahigh speed highly linear track and hold (TnH) circuit is needed in front of ADCwhich gives a stable signal at the input of ADC for accurate conversion. Twodifferent track and hold architectures are implemented, one is bootstrap TnH andother is switched source follower TnH. Simulations show that high speed with highlinearity can be achieved from bootstrap TnH circuit which is selected for the ADCdesign.Averaging technique is employed in the preamplifier array of ADC to reduce thestatic offsets of preamplifiers. The averaging technique can be made more efficientby using the smaller number of amplifiers. This can be done by using the interpolationtechnique which reduces the number of amplifiers at the input of ADC. Thereduced number of amplifiers is also advantageous for getting higher bandwidthsince the input capacitance at the first stage of preamplifier array is reduced.The flash ADC is designed and implemented in 150 nm CMOS technology for thesampling rate of 1.6 GSamples/sec. The bootstrap TnH consumes power of 27.95mW from a 1.8 V supply and achieves the signal to noise and distortion ratio(SNDR) of 37.38 dB for an input signal frequency of 195.3 MHz. The ADC withideal TnH and comparator consumes power of 78.2 mW and achieves 4.8 effectivenumber of bits (ENOB).

Today's radio frequency receivers for digital wireless communication are getting more and more complex. A single receiver unit should support multiple bands, have a wide bandwidth, be flexible and show good performance. To fulfil these requirements, new receiver architectures have to be developed and used. One possible alternative is the RF undersampling architecture. This thesis evaluates the RF undersampling architecture, which make use of an undersampling track-and-hold circuit with very wide bandwidth to perform direct sampling of the RF carrier before the analogue-to-digital converter. The architecture’s main advantages and drawbacks are identified and analyzed. Also, techniques and improvements to solve or reduce the main problems of the RF undersampling receiver are proposed.

La « vision » à travers les milieux opaques (murs, cloisons, décombres, ou plus généralement tout milieu qui occulte la vision humaine) est l’un des problèmes clefs du contrôle et de la sécurité. Il apparaît à l’heure actuelle un réel besoin de disposer de dispositifs d’observation à travers ces milieux pour des applications tant militaires (lors des assauts, des prises d’otages, etc.) que civiles (recherche de personnes enfouies dans des décombres, dans un incendie, etc). Les avancées sur cette problématique ont conduit à mettre en place des systèmes radars à très courte portée, opérationnels pour la détection et le tracking de personnes dans des environnements simples. Cependant ils nécessitent que les cibles soient en déplacement afin de les différencier des objets statiques. Cette limitation constitue un défaut majeur pour un certain nombre de scénarii réels où des personnes, par stratégie ou par contrainte, restent immobiles. Ces travaux de thèse visent à explorer les mécanismes de détection de personnes statiques par le biais de leurs micro-mouvements, e.g. des mouvements induits par le thorax lors de la respiration. Nous avons étudié - d’un point de vue théorique - les principes physiques sous-jacents à la détection de ces micro-mouvements par radar UWB impulsionnel à partir du mécanisme Doppler impulsionnel. Ce dernier s’appuie sur des mesures consécutives des phases des impulsions réfléchies. La compréhension de ce phénomène a permis de définir une architecture radar impulsionnelle et de la positionner, en termes de contributions, au regard des différents radars UWB proposés dans la littérature : le FMCW et le radar de bruit. Deux dispositifs radars ont servi de support à ce travail. Le premier, de type démonstrateur académique, repose sur l’utilisation d’un oscilloscope rapide pour numériser les impulsions UWB de 3 à 6 GHz de bande. Il a permis de mettre en place une chaîne de traitement complète de vision à travers les murs. Le second dispositif est un prototype radar développé autour d’une plateforme de numérisation ultra-rapide (100 Gsps par échantillonnage équivalent) de fréquence de rafraîchissement très élevée (100 Hz). Il est construit autour d’un FPGA, d’un ADC rapide (1,25 GHz) et d’un T&H très large bande (18 GHz). Il permet ainsi la détection des micro-mouvements par traitement Doppler impulsionnel. / "Vision" through opaque environments (walls, partitions, rubble, or any environment that obscures human vision) is one of the key issues of control and security. Advances on this issue have led to operational shortrange radar systems for people detection and tracking in simple environments. However, most of them require the targets to move in order to differentiate them from static objects. This requirement constitues a major shortcoming for a certain number of real scenarios where people, by strategies or by constraints, remain motionless. Hence, this thesis aims to explore the mechanisms of detection of static people through their micro-movements, e.g. movements induced by the thorax during breathing. We have studied - from a theoretical point of view - the physical principles underlying the detection of these micro-movements by pulsed UWB radar with the pulsed Doppler phenomenon, which relies on consecutive measurements of the reflected pulses phases. The understanding of this phenomenon made it possible to define a radar architecture and to position it, in terms of contributions, with regard to the different UWB radars proposed in the literature : the FMCW and the noise radar. Two radar devices served as support for this work. An academic demonstrator based on the use of a fast oscilloscope to digitize the pulses. It allowed to set up a complete processing chain for the application of vision through the walls. The second device is a radar prototype developed around a high-speed scanning platform (100 Gsps perequivalent sampling) with a very high refresh rate (100 Hz). This prototype is built around an FPGA, a fast ADC (1.25 GHz) and a very wide band T&H (18 GHz). This thereby enables to detect micro-movements by pulsed Doppler processing.

While data converters have been around for nearly nighty years, mm-wave data converters are still in their infancy. Only recently the 40-GHz sampling barrier was broken with the introduction of the next generation high-speed sampling oscilloscopes. Meanwhile, data communication is the main driving force behind mm-wave data converter development. As with any mm-wave circuit, designers must go beyond simply relying on technology advancement to archives acceptable performance. Careful device and passive modeling is critical and systematic design methodology may o er repeatable and scalable mm-wave designs. In this thesis the design methodology and architectural challenges of mm-wave ADCs are explored. Some of the fundamental mm-wave ADC building blocks such as track and hold ampli ers, data distribution networks and ip- ops are implemented in SiGe BiCMOS and CMOS technologies and characterized. Several record breaking circuits are presented along with systematic design methodology. The impact of these circuit blocks on the performance of the next generation ADCs is studied and experimentally veri ed using a 35-GS/s, 4-bit ADC-DAC chain implemented in a SiGe BiCMOS technology.

While data converters have been around for nearly nighty years, mm-wave data converters are still in their infancy. Only recently the 40-GHz sampling barrier was broken with the introduction of the next generation high-speed sampling oscilloscopes. Meanwhile, data communication is the main driving force behind mm-wave data converter development. As with any mm-wave circuit, designers must go beyond simply relying on technology advancement to archives acceptable performance. Careful device and passive modeling is critical and systematic design methodology may o er repeatable and scalable mm-wave designs. In this thesis the design methodology and architectural challenges of mm-wave ADCs are explored. Some of the fundamental mm-wave ADC building blocks such as track and hold ampli ers, data distribution networks and ip- ops are implemented in SiGe BiCMOS and CMOS technologies and characterized. Several record breaking circuits are presented along with systematic design methodology. The impact of these circuit blocks on the performance of the next generation ADCs is studied and experimentally veri ed using a 35-GS/s, 4-bit ADC-DAC chain implemented in a SiGe BiCMOS technology.

The objective of this research is to explore high-speed analog-to-digital converters (ADCs) using silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) for wireless digital receiver applications. The stringent requirements of ADCs for the high-performance next-generation wireless digital receiver include (1) low power, (2) low cost, (3) wide input signal bandwidth, (4) high sampling rate, and (5) medium to high resolution. The proposed research achieves the objective by implementing high-performance ADC's key building blocks and integrating these building blocks into a complete sigma-delta analog-to-digital modulator that satisfies the demanding specifications of next-generation wireless digital receiver applications. The scope of this research is divided into two main parts: (1) high-performance key building blocks of the ADC, and (2) high-speed sigma-delta analog-to-digital modulator. The research on ADC's building blocks includes the design of two high-speed track-and-hold amplifiers (THA) and two wide-bandwidth comparators operating at the sampling rate > 10 GS/sec with satisfying resolution. The research on high-speed sigma-delta analog-to-digital modulator includes the design and experimental characterization of a high-speed second-order low-pass sigma-delta modulator, which can operate with a sampling rate up to 20 GS/sec and with a medium resolution. The research is envisioned to demonstrate that the SiGe HBT technology is an ideal platform for the design of high-speed ADCs.

Signal-integrity degradation from such factors as supply and substrate noise and cross talk between interconnects restricts the performance advances in Very Large Scale Integration (VLSI). To avoid this and to keep the signal-integrity, accurate measurements of the on-chip signal must be performed to get an insight in how the physical phenomenon affects the signals. High-speed digital signals can be taken off chip, through buffers that add delay. Propagating a signal through buffers restores the signal, which can be good if only information is wanted. But if the waveform is of importance, or if an analog signal should be measured the restoration is unwanted. Analog buffers can be used but they are limited to some hundred MHz. Even if the high-speed signal is taken off chip, the bandwidth of on-chip signals is getting very high, making the use of an external oscilloscope impossible for reliable measurement. Therefore other alternatives must be used. In this work, an on-chip measuring circuit is designed, which makes use of the principle of a sampling oscilloscope. Only one sample is taken each period, resulting in an output frequency much lower than the input frequency. A slower signal is easier to take off-chip and it can easily be processed with an ordinary oscilloscope.

<p>Signal-integrity degradation from such factors as supply and substrate noise and cross talk between interconnects restricts the performance advances in Very Large Scale Integration (VLSI). To avoid this and to keep the signal-integrity, accurate measurements of the on-chip signal must be performed to get an insight in how the physical phenomenon affects the signals. </p><p>High-speed digital signals can be taken off chip, through buffers that add delay. Propagating a signal through buffers restores the signal, which can be good if only information is wanted. But if the waveform is of importance, or if an analog signal should be measured the restoration is unwanted. Analog buffers can be used but they are limited to some hundred MHz. Even if the high-speed signal is taken off chip, the bandwidth of on-chip signals is getting very high, making the use of an external oscilloscope impossible for reliable measurement. Therefore other alternatives must be used. </p><p>In this work, an on-chip measuring circuit is designed, which makes use of the principle of a sampling oscilloscope. Only one sample is taken each period, resulting in an output frequency much lower than the input frequency. A slower signal is easier to take off-chip and it can easily be processed with an ordinary oscilloscope.</p>

Les communications futures pour les applications civiles et militaires utilisent des signaux modulés complexes large bande qui seront émis à travers des amplificateurs de puissance multivoie de type DOHERTY qui devront avoir des performances en puissance, rendement, OBO et largeur de bande qui constituent aujourd’hui un véritable défi à relever. Pour ce faire les concepteurs ont besoin d’outils de caractérisation temporelle permettant la mesure normalisées et l’optimisation des tensions et courants aux accès des dispositifs non linéaires sous pointes ou connectorisés. Ce travail de thèse a permis de mettre en œuvre cet outil de caractérisation temporelle qui a été utilisé pour répondre à des besoins spécifiques pour la modélisation de transistor, pour l’optimisation de leur fonctionnement en termes de stabilité impulsion à impulsion, pour la recherche des conditions optimales de leur fonctionnement dans un amplificateur de type Doherty. Pour cette mise en œuvre une modélisation mathématique des échantillonneurs a été réalisée pour évaluer leurs performances et choisir le mieux adapté à la mesure temporelle RF. Des procédures d’étalonnages rigoureuses ont été développées pour obtenir simultanément des formes d’ondes temporelles calibrées à spectre très large (Basse fréquences jusqu’aux Hyperfréquences). / The future communications for civil and military applications will use complex wideband modulated signals to be transmitted through multi-channel DOHERTY power amplifiers which should have high performance in terms of power, efficiency, OBO, and bandwidth. In order to meet these stringent requirements, designers need time-domain characterization tools for calibrated measurements and for optimizing voltages and currents at both ports of non-linear connectorized or on-wafer devices. This work successfully implements time-domain characterization tools used to meet specific needs for transistor modeling, to optimize their operation in terms of pulse to pulse stability, and to search optimal conditions of their operation modes in a Doherty power amplifier. For this implementation, mathematical modeling is performed to evaluate sampler’s performances in terms of time-domain sampling efficiency in order to choose the best suited sampling architecture for RF time-domain measurements. Rigorous calibration procedures have been developed to obtain simultaneously full time-domain calibrated waveforms (from low Frequencies to Microwave frequencies).