Many emerging applications call for wideband analog-to-digital converters and some require medium-to-high resolution. Incorporating such ADCs allows for shifting as much of the signal processing tasks as possible to the digital domain, where more flexible and programmable circuits are available. However, realizing such ADCs with the existing single stage architectures is very challenging. Therefore, parallel ADC architectures such as time-interleaved structures are used. Unfortunately, such architectures require high-speed high-precision sample-and-hold (S/H) stages that are challenging to implement. In this thesis, a parallel ADC architecture, namely, the frequency-translating hybrid ADC (FTH-ADC) is proposed to increase the conversion speed of the ADCs, which is also suitable for applications requiring medium-to-high resolution ADCs. This architecture addresses the sampling problem by sampling on narrowband baseband subchannels, i.e., sampling is accomplished after splitting the wideband input signals into narrower subbands and frequency-translating them into baseband where identical narrowband baseband S/Hs can be used. Therefore, lower-speed, lower-precision S/Hs are required and single-chip CMOS implementation of the entire ADC is possible. A proof of concept board-level implementation of the FTH-ADC is used to analyze the effects of major analog non-idealities and errors. Error measurement and compensation methods are presented. Using four 8-bit, 100 MHz subband ADCs, four 25 MHz Butterworth filters, two 64-tap FIR reconstruction filters, and four 10-tap FIR compensation filters, a total system with an effective sample rate of 200 MHz is implemented with an effective number of bits of at least 7 bits over the entire 100 MHz input bandwidth. In addition, one path of an 8-GHz, 4-bit, FTH-ADC system, including a highly-linear mixer and a 5th-order, 1 GHz, Butterworth Gm-C filter, is implemented in a 90 nm CMOS technology. Followed by a 4-bit, 4-GHz subband ADC, the blocks consume a total power of 52 mW from a 1.2 V supply, and occupy an area of 0.05 mm2. The mixer-filter has a THD ≤ 5% (26 dB) over its full 1 GHz bandwidth and provides a signal with a voltage swing of 350 mVpp for the subsequent ADC stage.

The continued speed improvement of serial links and appearance of new communication technologies, such as ultra wideband (UWB), have introduced increasing demands on the speed and power specifications of high speed low to medium resolution analog to digital converters (ADCs). While multi channel ADCs can achieve high speeds, they often require extensive and costly post fabrication calibration. A single channel 4 bit flash ADC, suitable for abovementioned or similar applications, implemented entirely using current mode logic (CML) blocks, is presented. CML implementation allows for high sampling rates, while typically providing low power consumption at high speeds. To improve the conversion rate, both the analog (comparator array) and the digital (encoder) parts of the ADC are fully pipelined. Furthermore, the logic functions in the encoder are reformulated to reduce wire crossings and delay and to equalize the wires lengths in the layout. To keep the design simple, inductors are avoided. As a result, a compact design with small wire parasitics is achieved. Moreover, some geometric layout techniques, including a common centroid layout for the resistor ladder, are introduced to reduce the effect of mismatches to eliminate the use of digital calibration. The ADC is designed and fabricated in 0.18um CMOS and operates at 4GS/s. It achieves an effective number of bits (ENOB) of 3.71 (3.14, 2.75) for a 10MHz (0.501GHz, 1.491GHz) signal sampled at 4GS/s (3GS/s, 3GS/s). Differential/integral nonlinearity (DNL/INL) errors are between +/-0.35LSB and +/-0.26LSB, respectively. The ADC consumes 43mW from a 1.8V supply and occupies 0.06mm2 active area. Due to the use of CML circuits, the ADC achieves the highest speed reported for a single channel 4 bit ADC in a 0.18um CMOS technology. It also reports the best power performance among the 4-bit ADCs with similar or higher speeds. The active area is also among the smallest reported. In addition, in this thesis, the signal to noise ratio (SNR) of an ADC is formulated in terms of its INL performance. The related formulas in the literature are not accurate for low resolution ADCs, and yet they do not take the input waveform into account. Two standard waveforms, ramp and sinusoid, are considered here. The SNR formulas are derived and confirmed by simulation results.

SAR-ADCs are very popular and suitable for conversions up to few tens of MHz with 8 to 12 bits of resolution. A very popular type is the Charge Redistribution SAR-ADC which is based on a capacitive array. Higher speeds can be achieved by using the interleaving technique where a number of SAR-ADCs are working in parallel. These speeds, however, can only be achieved if the reference voltage can cope with the switching of the capacitive array. In this thesis the design of a programmable voltage reference generator for a Charge Redistribution SAR-ADC was studied. A number of architectures were studied and one based on a Current Steering DAC was chosen because of the settling time that could offer to the Charge Redistribution SAR-ADC switching operation. This architecture was further investigated in order to spot the weak points of the design and try to minimize the settling time. In the end, the final design was evaluated and possible trimming techniques were proposed that could further speed up the design.

No description available.

Rapid scaling in technology has introduced new challenges in the realm of traditional analog design. Scaling of supply voltage directly impacts the available voltage-dynamic-range. On the other hand, nanometric technologies with fT in the hundreds of GHz range open opportunities for time-resolution-based signal processing. With reduced available voltage-dynamic-range and improved timing resolution, it is more convenient to devise analog circuits whose performance depends on edge-timing precision rather than voltage levels. Thus, instead of representing the data/information in the voltage-mode, as a difference between two node voltages, it should be represented in time-mode as a time-difference between two rising and/or falling edges. This dissertation addresses the feasibility of employing time-mode analog circuit design in different applications. Specifically: 1) Time-mode-based quanitzer and feedback DAC of SigmaDelta ADC. 2) Time-mode-based low-THD 10MHz oscillator, 3) A Spur-Frequency Boosting PLL with -74dBc Reference-Spur Rejection in 90nm Digital CMOS. In the first project, a new architectural solution is proposed to replace the DAC and the quantizer by a Time-to-Digital converter. The architecture has been fabricated in 65nm and shows that this technology node is capable of achieving a time-matching of 800fs which has never been reported. In addition, a competitive figure-of-merit is achieved. In the low-THD oscillator, I proposed a new architectural solution for synthesizing a highly-linear sinusoidal signal using a novel harmonic rejection approach. The chip is fabricated in 130nm technology and shows an outstanding performance compared to the state of the art. The designed consumes 80% less power; consumes less area; provides much higher amplitude while being composed of purely digital circuits and passive elements. Last but not least, the spur-frequency boosting PLL employs a novel technique that eliminates the reference spurs. Instead of adding additional filtering at the reference frequency, the spur frequency is boosted to higher frequency which is, naturally, has higher filtering effects. The prototype is fabricated in 90nm digital CMOS and proved to provide the lowest normalized reference spurs ever reported.

El presente trabajo de título consistió en la elaboración de un osciloscopio digital de propósito general, sencillo de implementar y de bajo costo. El sistema está dividido en tres fases principales: la etapa de adquisición y acondicionamiento de la señal, transporte de la información por USB y transmisión de dicha información dentro de una red LAN utilizando microcontroladores PIC. En cuanto al acondicionamiento de la señal, se diseñó en base a lo visto en la revisión bibliográfica una atenuación inicial y posterior amplificación variable mediante amplificadores operacionales de ganancia variable, controlada digitalmente mediante la multiplexión de un arreglo de resistencias que definen la ganancia. La idea fundamental fue acondicionar señales de distinta amplitud al rango dinámico del conversor análogodigital utilizado (0 – 5 volts). Una vez convertido el dato mediante interrupciones que garantizan la separación constante de tiempo entre muestras, se guarda dentro de la RAM interna del PIC y mediante transacciones PC-Microcontrolador PIC18F2550 se envían paquetes de datos por USB, los cuales son procesados y posteriormente graficados. Paralelo a esto, se trasfieren los datos captados a un segundo PIC (18F452), el cual define una conexión TCP/IP mediante el controlador Ethernet ENC28J60 y envía paquetes con la información recibida dentro de una LAN. Independiente al método de adquisición utilizado (USB o Ethernet), se diseñó un software basado en capas o módulos, el cual recibe la información, y la guarda en una cadena, y dependiendo si está o no definida la opción de trigger, localiza el punto de disparo y lo centra en pantalla, lo cual da la posibilidad de implementar también un control de desplazamiento vertical.

abstract: In thesis, a test time reduction (a low cost test) methodology for digitally-calibrated pipeline analog-to-digital converters (ADCs) is presented. A long calibration time is required in the final test to validate performance of these designs. To reduce total test time, optimized calibration technique and calibrated effective number of bits (ENOB) prediction from calibration coefficient will be presented. With the prediction technique, failed devices can be identified only without actual calibration. This technique reduces significant amount of time for the total test time. / Dissertation/Thesis / M.S. Electrical Engineering 2013

abstract: Analysing and measuring of biological or biochemical processes are of utmost importance for medical, biological and biotechnological applications. Point of care diagnostic system, composing of biosensors, have promising applications for providing cheap, accurate and portable diagnosis. Owing to these expanding medical applications and advances made by semiconductor industry biosensors have seen a tremendous growth in the past few decades. Also emergence of microfluidics and non-invasive biosensing applications are other marker propellers. Analyzing biological signals using transducers is difficult due to the challenges in interfacing an electronic system to the biological environment. Detection limit, detection time, dynamic range, specificity to the analyte, sensitivity and reliability of these devices are some of the challenges in developing and integrating these devices. Significant amount of research in the field of biosensors has been focused on improving the design, fabrication process and their integration with microfluidics to address these challenges. This work presents new techniques, design and systems to improve the interface between the electronic system and the biological environment. This dissertation uses CMOS circuit design to improve the reliability of these devices. Also this work addresses the challenges in designing the electronic system used for processing the output of the transducer, which converts biological signal into electronic signal. / Dissertation/Thesis / M.S. Electrical Engineering 2014

Many emerging applications call for wideband analog-to-digital converters and some require medium-to-high resolution. Incorporating such ADCs allows for shifting as much of the signal processing tasks as possible to the digital domain, where more flexible and programmable circuits are available. However, realizing such ADCs with the existing single stage architectures is very challenging. Therefore, parallel ADC architectures such as time-interleaved structures are used. Unfortunately, such architectures require high-speed high-precision sample-and-hold (S/H) stages that are challenging to implement. In this thesis, a parallel ADC architecture, namely, the frequency-translating hybrid ADC (FTH-ADC) is proposed to increase the conversion speed of the ADCs, which is also suitable for applications requiring medium-to-high resolution ADCs. This architecture addresses the sampling problem by sampling on narrowband baseband subchannels, i.e., sampling is accomplished after splitting the wideband input signals into narrower subbands and frequency-translating them into baseband where identical narrowband baseband S/Hs can be used. Therefore, lower-speed, lower-precision S/Hs are required and single-chip CMOS implementation of the entire ADC is possible. A proof of concept board-level implementation of the FTH-ADC is used to analyze the effects of major analog non-idealities and errors. Error measurement and compensation methods are presented. Using four 8-bit, 100 MHz subband ADCs, four 25 MHz Butterworth filters, two 64-tap FIR reconstruction filters, and four 10-tap FIR compensation filters, a total system with an effective sample rate of 200 MHz is implemented with an effective number of bits of at least 7 bits over the entire 100 MHz input bandwidth. In addition, one path of an 8-GHz, 4-bit, FTH-ADC system, including a highly-linear mixer and a 5th-order, 1 GHz, Butterworth Gm-C filter, is implemented in a 90 nm CMOS technology. Followed by a 4-bit, 4-GHz subband ADC, the blocks consume a total power of 52 mW from a 1.2 V supply, and occupy an area of 0.05 mm2. The mixer-filter has a THD ≤ 5% (26 dB) over its full 1 GHz bandwidth and provides a signal with a voltage swing of 350 mVpp for the subsequent ADC stage. / Applied Science, Faculty of / Electrical and Computer Engineering, Department of / Graduate

The continued speed improvement of serial links and appearance of new communication technologies, such as ultra wideband (UWB), have introduced increasing demands on the speed and power specifications of high speed low to medium resolution analog to digital converters (ADCs). While multi channel ADCs can achieve high speeds, they often require extensive and costly post fabrication calibration. A single channel 4 bit flash ADC, suitable for abovementioned or similar applications, implemented entirely using current mode logic (CML) blocks, is presented. CML implementation allows for high sampling rates, while typically providing low power consumption at high speeds. To improve the conversion rate, both the analog (comparator array) and the digital (encoder) parts of the ADC are fully pipelined. Furthermore, the logic functions in the encoder are reformulated to reduce wire crossings and delay and to equalize the wires lengths in the layout. To keep the design simple, inductors are avoided. As a result, a compact design with small wire parasitics is achieved. Moreover, some geometric layout techniques, including a common centroid layout for the resistor ladder, are introduced to reduce the effect of mismatches to eliminate the use of digital calibration. The ADC is designed and fabricated in 0.18um CMOS and operates at 4GS/s. It achieves an effective number of bits (ENOB) of 3.71 (3.14, 2.75) for a 10MHz (0.501GHz, 1.491GHz) signal sampled at 4GS/s (3GS/s, 3GS/s). Differential/integral nonlinearity (DNL/INL) errors are between +/-0.35LSB and +/-0.26LSB, respectively. The ADC consumes 43mW from a 1.8V supply and occupies 0.06mm2 active area. Due to the use of CML circuits, the ADC achieves the highest speed reported for a single channel 4 bit ADC in a 0.18um CMOS technology. It also reports the best power performance among the 4-bit ADCs with similar or higher speeds. The active area is also among the smallest reported. In addition, in this thesis, the signal to noise ratio (SNR) of an ADC is formulated in terms of its INL performance. The related formulas in the literature are not accurate for low resolution ADCs, and yet they do not take the input waveform into account. Two standard waveforms, ramp and sinusoid, are considered here. The SNR formulas are derived and confirmed by simulation results. / Applied Science, Faculty of / Electrical and Computer Engineering, Department of / Graduate