First-generation, line-of-sight (LOS) fixed broadband wireless access techniques have been around for several years. However, services based on this technology have been limited in scope to service areas where transceivers can communicate with their base stations, unimpeded by trees, buildings and other obstructions. This limitation has serious consequences in that the system can deliver only 50% to 70% coverage within a given cell radius, thus affecting earned revenue. Next generation broadband fixed wireless access techniques are aimed at achieving a coverage area greater than 90%. To achieve this target, these techniques must be based on a point-to-multipoint (PMP) cellular architecture with low base station antennas, thus possessing the ability to operate in true non-line-of-sight (NLOS) conditions. A possible limiting factor for these systems is link degradation due to interference. This thesis presents a new model to estimate the levels of co-channel interference for such systems operating within the 3.5 GHz multichannel multipoint distribution service (MMDS) band. The model is site-specific in that it uses statistical building/roof height distribution parameters obtained from practically modeling several metropolitan cities in the U.S. using geographic information system (GIS) tools. This helps to obtain a realistic estimate and helps analyze the tradeoff between cell radius and modulation complexity. Together, these allow the system designer to decide on an optimal location for placement of customer premises equipment (CPE) within a given cell area. / Master of Science

The objective of this dissertation is to better understand the impact of the range extension and interference effects of opportunistic large arrays (OLAs), in the context of cooperative routing in multi-hop ad hoc networks. OLAs are a type of concurrent cooperative transmission (CCT), in which the number and location of nodes that will participate in a particular CCT cannot be known a priori. The motivation of this research is that the previous CCT research simplifies or neglects significant issues that impact the CCT-based network performance. Therefore, to develop and design more efficient and realistic OLA-based protocols, we clarify and examine through experimentation and analysis the simplified or neglected characteristics of CCT, which should be considered in the network-level system design. The main contributions of this research are (i) intra-flow interference analysis and throughput optimization in both disk- and strip-shaped networks, for multi-packet OLA transmission, (ii) CCT link modeling focusing on path-loss disparity and link asymmetry, (iii) demonstration of CCT range-extension and OLA-based routing using a software-defined radio (SDR) test-bed, (iv) a new OLA-based routing protocol with practical error control algorithm. In the throughput optimization in presence of the intra-channel interference, we analyze the feasibility condition of spatially pipelined OLA transmissions using the same channel and present numerical results with various system parameters. In the CCT link model, we provide the impact of path-loss disparity that are inherent in a virtual multiple-input-single-output (VMISO) link and propose an approximate model to calculate outage rates in high signal-to-noise-ratio (SNR) regime. Moreover, we present why link asymmetry is relatively more severe in CCT compared to single-input-single-output (SISO) links. The experimental studies show actual measurement values of the CCT range extension and realistic performance evaluation of OLA-based routing. Lastly, OLA with primary route set-up (OLA-PRISE) is proposed with a practical route recovery technique.

The cooperative relaying scheme is a promising technique for increasing the capacity and reliability of wireless communication. Even though extensive research has performed in information theoretical aspect, there are still many unresolved practical problems of cooperative relaying system. This dissertation analyzes the performance of cooperative decode-and-forward (DF) relaying systems in the presence of multiple interferers and improve network throughput for these systems. We propose and summarize various systems in the view of network topology, transmission structure, and slot allocation. We present closed-form expressions for the end-to-end outage probability, average symbol-error-probability, average packet-error-probability, and network throughput of the proposed systems. This dissertation shows that the robustness of the destination against interference is more important than robustness of the relay against interference from an interference management perspective, and increasing the number of branches yields better outage and error performance improvements against shadowing than increasing the number of hops. In cellular networks, the cooperative diversity systems can outperform the dual-Rx antenna system, but only when the relay is located in a relatively small portion of the total cell area with respect the the destination mobile terminal. The results also show that since the effective regions of the uplink and the downlink do not overlap, different relays should be utilized for cell sectorization in the uplink and the downlink. Finally, the proposed variable-slot selection DF scheme can reduce the system complexity and make the maximum throughput point in the low and moderate signal-to-interference-plus-noise ratio region.

Interference and jamming severely disrupt our ability to communicate by decreasing the effective signal-to-noise ratio and by making parameter estimation difficult at the receiver. The objective of this research work is to design robust wireless systems and algorithms to suppress the adverse effects of non-intentional co-channel interference (CCI) or intentional jamming. In particular, we develop chip-combining schemes with timing, channel, and noise-power estimation techniques, all of which mitigate CCI or jamming. We also exploit the spatial diversity and iterative receiver techniques for this purpose. Most of the existing timing estimation algorithms are robust against either large frequency offsets or CCI, but not against both at the same time. Hence, we develop a new frame boundary estimation method that is robust in the presence of severe co-channel interference and large carrier-frequency offsets. To solve the high peak-to-average-power ratio problem of a multicarrier code division multiple access (MC-CDMA) system and enhance its robustness against fading and jamming, we propose a constant-envelope MC-CDMA system employing cyclic delay diversity (CDD) as transmit diversity. We analyze the diversity order, coding gain, and bit-error rate upper bound. We also propose a blind, accurate, and computationally efficient signal-to-noise ratio estimator for the proposed system. We propose a configurable robust anti-jam receiver that estimates the frequency- or time-domain jammer state information (JSI) and uses it for chip combining in the corresponding domain. A soft-JSI-based chip-combining technique is proposed that outperforms conventional hard-JSI-based chip combining. We also derive a chip combiner that provides sufficient statistics to the decoder. Channel estimation is necessary for coherent signal detection and JSI estimation. Conversely, knowledge of the jamming signal power and JSI of different subcarriers can improve the accuracy of the channel estimates. Hence, we propose joint iterative estimation of the multiple-input multiple-output (MIMO) channel coefficients, jamming power, and JSI for a coded MC-CDMA MIMO system operating under jamming and a time-varying frequency-selective fading channel. Finally, we reduce the computational complexity of the JSI-based anti-jam receivers by introducing an expectation-maximization-based joint channel and noise-covariance estimator that does not need either the subcarrier JSI or the individual powers of the AWGN and jamming signal.

L’amélioration de la qualité et de l’efficacité en santé est un réel enjeu sociétal. Elle implique la surveillance continue des paramètres vitaux ou de l’état mental du sujet. Les champs d’applications sont vastes : l’application la plus importante est la surveillance des patients à distance. Les avancées en micro-électronique, capteurs et réseaux sans-fil permettent aujourd’hui le développement de systèmes ambulatoires performants pour le monitoring de paramètres physiologiques, capables de prendre en compte d’importantes contraintes techniques : forte intégration pour la réduction de la taille et faible consommation pour une plus grande autonomie [1]. Cependant, la conception de ce type de réseaux de capteurs médicaux WBANs (Wireles Body Area Networks) se heurte à un certain nombre de difficultés techniques, provenant des contraintes imposées par les capacités réduites des capteurs individuels : basse puissance, énergie limitée et faible capacité de stockage. Ces difficultés requièrent des solutions différentes, encore très embryonnaires, selon l’application visée (monitoring à but médical). La forte mobilité et le changement rapide de la topologie du réseau dévoilent un verrou scientifique et social. En outre, l’interférence de différents capteurs constituant le WBAN augmente la difficulté de la mise en place de ce type de réseaux. De nombreuses solutions dans la littérature ont été étudiées, comme nous allons illustrer dans ce manuscrit, néanmoins elles restent limitées. Nous nous intéresserons tout particulièrement à la gestion des interférences Intra- et Inter-WBAN, leur impacte sur la fiabilité des transmissions (des liens) et la durée de vie de ce type de réseaux. Plus précisément, nous abordons ces problématiques en se basant sur des modélisations théoriques et analytiques et avec une conception pratique des solutions proposées. Afin d’atteindre les objectifs cités ci-dessous, nous abordons quatre solutions : • Une gestion des interférences intra-WBAN • Une gestion coopérative des interférences Inter-WBAN • Une gestion non coopérative des interférences, Inter-WBAN • Une gestion des interférences WBAN dans un contexte IoT Dans la première partie de cette thèse et afin de répondre en partie aux problèmes de gestion des interférences Intra-WBAN. Nous présentons deux mécanismes pour le WBAN : (a) CFTIM qui alloue dynamiquement des slots et des canaux dit- stables (avec un taux d’interférences le bas possible dans le temps) pour réduire les interférences intra-WBAN. (b) IAA ajuste dynamiquement la taille du superframe et limite le nombre de canaux à 2 pour abaisser les interférences Intra-WBAN et ainsi économiser l’énergie. Une validation avec un model probabiliste est proposé afin de valider théoriquement l’efficacité de notre solution. Les résultats de la simulation démontrent l’efficacité du CFTIM et de l’IAA en termes de réduction de la probabilité d’interférence, l’extension de la durée de vie du réseau et l’amélioration du débit et de la fiabilité des transmissions. Notre seconde contribution, propose une gestion coopératives des interférences Inter-WBAN en utilisant des codes orthogonaux. Motivé par un approvisionnement temporel distribué basé sur la norme [2] IEEE 802.15.6, nous proposons deux solutions. (a) DTRC qui fournit à chaque WBAN les connaissances sur les superframes qui se chevauchent. Le second, (b) OCAIM qui attribue des codes orthogonaux aux capteurs appartenant à deux listes de groupe de capteur en interférences de deux WBAN différents (SIL). Les résultats démontrent qu’OCAIM diminue les interférences, améliore le débit et préserve la ressources énergétiques. La troisième partie nous a permis d’aborder la gestion des interférences, mais cette fois ci d’une manière non-coopérative en se basant sur l’affectation couple Slot/Canal. Plus précisément, nous proposons deux schémas basés sur les carrés latins. (...) / A Wireless Body Area Network (WBAN) is a short-range network that consists of a coordinator (Crd) and a collection of low-power sensors that can be implanted in or attached to the human body. Basically, WBANs can provide real-time patient monitoring and serve in various applications such as ubiquitous health-care, consumer electronics, military, sports, etc. [1]. As the license-free 2.4 GHz ISM band is widely used among WBANs and across other wireless technologies, the fundamental problem is to mitigate the resulting co-channel interference. Other serious problems are to extend the network lifetime and to ensure reliable transmission within WBANs, which is an urgent requirement for health-care applications. Therefore, in this thesis, we conduct a systematic research on a few number of research problems related to radio co-channel interference, energy consumption, and network reliability. Specifically, we address the following problems ranging from theoretical modeling and analysis to practical protocol design: • Intra-WBAN interference mitigation and avoidance • Cooperative inter-WBAN interference mitigation and avoidance • Non-cooperative inter-WBAN interference mitigation and avoidance • Interference mitigation and avoidance in WBANs with IoT Firstly, to mitigate the intra-WBAN interference, we present two mechanisms for a WBAN. The first is called CSMA to Flexible TDMA combination for Interference Mitigation, namely, CFTIM, which dynamically allocates time-slots and stable channels to lower the intra-WBAN interference. The second is called Interference Avoidance Algorithm, namely IAA that dynamically adjusts the superframe length and limits the number of channels to 2 to lower the intra-WBAN interference and save energy. Theoretically, we derive a probabilistic model that proves the SINR outage probability is lowered. Simulation results demonstrate the effectiveness and the efficiency of CFTIM and IAA in terms of lowering the probability of interference, extending network lifetime, improving throughput and reliability. Secondly, we address the problem of interference among cooperative WBANs through using orthogonal codes. Motivated by distributed time provisioning supported in IEEE 802.15.6 standard [2], we propose two schemes. The first is called Distributed Time Correlation Reference, namely, DTRC that provides each WBAN with the knowledge about which superframes overlap with each other. The second is called Orthogonal Code Allocation Algorithm for Interference Mitigation, namely, OCAIM, that allocates orthogonal codes to interfering sensors belonging to sensor interference lists (SILs), which are generated based on the exchange of power-based information among WBANs. Mathematically, we derive the successful and collision probabilities of frames transmissions. Extensive simulations are conducted and the results demonstrate that OCAIM can diminish the interference, improve the throughput and save the power resource. Thirdly, we address the problem of co-channel interference among non-cooperative WBANs through time-slot and channel hopping. Specifically, we propose two schemes that are based on Latin rectangles. The first is called Distributed Algorithm for Interference mitigation using Latin rectangles, namely, DAIL that allocates a single channel to a timeslot combination to each sensor to diminish inter-WBAN interference and to yield better schedules of the medium access within each WBAN. The second is called Channel Hopping for Interference Mitigation, namely, CHIM, which generates a predictable interference free transmission schedule for all sensors within a WBAN. CHIM applies the channel switching only when a sensor experiences interference to save the power resource. Furthermore, we present an analytical model that derives bounds on collision probability and throughput for sensors transmissions. (...)

This dissertation focuses on quantifying the effects of multi-user co-channel interference for an avionic communication system operating in a heavy-traffic aeronautical mobile environment and proposes advanced interference cancellation techniques to mitigate the interference. The dissertation consists of two parts. The first part of the work investigates the use of a visualization method to quantify and characterize the multi-user co-channel interference (multiple access interference) effects impinging on an avionic communication system. The interference is caused by complex interactions of thousands of RF signals transmitted from thousands of aircraft; each attempts to access a common communication channel, which is governed by a specific channel contention access protocol. The visualization method transforms the co-channel interference, which is specified in terms of signal-overlaps (signal collisions), from a visual representation to a matrix representation for further statistical analysis. It is found that the statistical Poisson and its cumulative distribution provide the best estimates of multi-user co-channel interference. It is shown, using Monte Carlo simulation, that the co-channel interference of a victim aircraft operating in the heavy-traffic environment could result in as high as eight signal-overlaps. This constitutes to approximately 83.4% of success rate in signal detection for the entire three thousand aircraft environment using conventional FSK receiver. One key finding shows that high-quality communications, up to 98.5% success rate, is achievable if only three overlapping signals can be decoded successfully. The interference results found in the first part set the stage for interference cancellation research in the second part. The second part of the work proposes the use of advanced interference cancellation techniques, namely sequential interference cancellation (SIC) and parallel interference cancellation (PIC), as potential solutions to mitigating the interference effects. These techniques can be implemented in radio receivers to perform multi-signal decoding functionality to remove the required interferers (three overlapping signals) so that high-quality communication, as described in the first part, can be achieved. Various performance graphs are shown for B-FSK and B-PSK for both SIC and PIC techniques. One key finding is that the system performance can be improved substantially to an additional 15% in signal reception success rate by using SIC or PIC. This means that critical information transmitted from 450 aircraft (out of approximately three thousand aircraft in the environment) is preserved and successfully decoded. Multi-signal decoding using these interference cancellation receivers comes at a small penalty of 2 - 4.5 dBs in Eb/No when sufficient signal-to-interference (SIR) ratio (7-12 dB) is provided. / Ph. D.

This thesis presents the results of the development of a user-friendly computer code (in MATLAB) that can be used to calculate co-channel interferences, both in the downlink and in the uplink of a single satellite/space-based mobile communications system, due to the reuse of frequencies in spot beams or coverage cells. The analysis and computer code can be applied to any type of satellite or platform elevated at any height above earth. The cells or beams are defined in the angular domain, as measured from the satellite or the elevated platform, and cell centers are arranged in a hexagonal lattice. The calculation is only for a given instant of time for which the system parameters are input into the program. The results obtained in one program run are for the overall carrier to interference ratio (CIR) along with CIR for both the uplink and downlink paths. An overall carrier to noise plus interference ratio (CNIR) is also calculated, which exemplifies the degradation in the carrier to noise ratio (CNR) of the system. Comparisons for systems with differing system scenarios are also made. For example, overall CIRs are compared for different reuse numbers (3, 4, 7, and 13) in LEO and GEO satellite systems. In conclusion, as expected, it is observed that the co-channel interference generally increases as we decrease the reuse number employed for the frequency reuse in the cells. It is also observed that co-channel interference can cause substantial degradation to the overall CNR of a system. / Master of Science

A new broadband beamformer composed of nested arrays (NAs), multi-dimensional (MD) filters, and multirate techniques is proposed for both linear and planar arrays. It is shown that this combination results in frequency-invariant response. For a given number of sensors, the advantage of using NAs is that the effective aperture for low temporal frequencies is larger than in the case of using uniform arrays. This leads to high spatial selectivity for low frequencies. For a given aperture size, the proposed beamformer can be implemented with significantly fewer sensors and less computation than uniform arrays with a slight deterioration in performance. Taking advantage of the Noble identity and polyphase structures, the proposed method can be efficiently implemented. Simulation results demonstrate the good performance of the proposed beamformer in terms of frequency-invariant response and computational requirements. The broadband beamformer requires a filter bank with a non-compatible set of sampling rates which is challenging to be designed. To address this issue, a filter bank design approach is presented. The approach is based on formulating the design problem as an optimization problem with a performance index which consists of a term depending on perfect reconstruction (PR) and a term depending on the magnitude specifications of the analysis filters. The design objectives are to achieve almost perfect reconstruction (PR) and have the analysis filters satisfying some prescribed frequency specifications. Several design examples are considered to show the satisfactory performance of the proposed method. A new blind multi-stage space-time equalizer (STE) is proposed which can separate narrowband sources from a mixed signal. Neither the direction of arrival (DOA) nor a training sequence is assumed to be available for the receiver. The beamformer and equalizer are jointly updated to combat both co-channel interference (CCI) and inter-symbol interference (ISI) effectively. Using subarray beamformers, the DOA, possibly time-varying, of the captured signal is estimated and tracked. The estimated DOA is used by the beamformer to provide strong CCI cancellation. In order to alleviate inter-stage error propagation significantly, a mean-square-error sorting algorithm is used which assigns detected sources to different stages according to the reconstruction error at different stages. Further, to speed up the convergence, a simple-yet-efficient DOA estimation algorithm is proposed which can provide good initial DOAs for the multi-stage STE. Simulation results illustrate the good performance of the proposed STE and show that it can effectively deal with changing DOAs and time variant channels. / Graduate / 0544 / imanmoaz@uvic.ca

Cooperative relay systems have emerged as promising techniques to boost the performance of wireless systems. Recent studies have confirmed that interferences, co-channel interferences (CCIs) and self-interferences, have a huge impact on cooperative relay systems and can cause significant performance degradation. Two problems were observed in this research. Firstly, previous studies on performance analysis of Amplify-and-Forward (AF) relay systems in presence of CCIs have only focused on a specific interference channel model. However, in practical design scenarios, such an assumption is not a realistic proposition. Secondly, analyses of overheads introduced by a time-based relay selection protocol in distributed cooperative systems have been based on an over-pessimistic assumption where all packets involved in a collision are destroyed. Nevertheless, collisions due to the protocol overheads cause the system performance to be degraded but this does not mean that the failure of end-to-end transmission certainly occurs. The thesis aims to analyse the performance of practical cooperative relay systems in the presence of CCIs and self-interferences, by developing exact mathematical methods. A new unified mathematical method for AF relay systems in presence of a random number of arbitrary non-identical CCIs was developed. The obtained new approach derived in terms of a moment generating function of the aggregate interferences' power led to the derivation of new explicit expressions. The new results greatly simplify evaluation of average error rates over diverse practical interference scenarios. Moreover, a new exact mathematical analysis for distributed cooperative relay systems employing a time-based relay selection protocol based on an accurate interference model was presented. This approach led to the derivation of new exact expressions for the spectral efficiency which accounts for both self-interferences and the protocol overheads as well as for different fading scenarios and arbitrary relay locations. This approach provided several advantages over direct approaches, one of which is that it significantly simplified averaging-out the joint random variables involved.

No description available.