For decades, the Silicon-based semiconductors have been the solution for power electronics applications. However, these semiconductors have approached their limits of operation in blocking voltage, working temperature and switching frequency. Due to material superiority, the relatively-new wide-bandgap semiconductors such as Silicon-Carbide (SiC) MOSFETs enable higher voltages, switching frequencies and operating temperatures when compared to Silicon technology, resulting in improved converter specifications. The current study tries to investigate the impact of emerging medium-voltage SiC MOSFETs on industrial motor drive application, where over a quarter of the total electricity in the world is being consumed. Firstly, non-commercial SiC MOSFETs at 3.3 kV and 400 A rating are characterized to enable converter design and simulation based on them. In order to feature the best performance out of the devices under test, an intelligent high-performance gate driver is designed embedding required functionalities and protections. Secondly, total of three converters are targeted for industrial motor drive application at medium-voltage and high-power range. For this purpose the cascaded H-bridge, the modular multilevel converter and the 5-L active neutral point clamped converters are designed at 4.16-, 6.9- and 13.8 kV voltage ratings and 3- and 5 MVA power ratings. Selection of different voltage and power levels is done to elucidate variation of different parameters within the converters versus operating point. Later, comparisons are done between the surveyed topologies designed at different operating points based on Si IGBTs and SiC MOSFETs. The comparison includes different aspects such as efficiency, power density, semiconductor utilization, energy stored in converter structure, fault containment, low-speed operation capability and parts count (for a measure of reliability). Having the comparisons done based on simulation data, an H-bridge cell is implemented using 3.3 kV 400 A SiC MOSFETs to evaluate validity of the conducted simulations. Finally, a novel method is proposed for series-connecting individual SiC MOSFETs to reach higher voltage devices. Considering the fact that currently the SiC MOSFETs are not commercially available at voltages higher above 1.7 kV, this will enable implementation of converters using medium-voltage SiC MOSFETs that are achieved by stacking commercially-available 1.7 kV MOSFETs. The proposed method is specifically developed for SiC MOSFETs with high dv/dt rates, while majority of the existing solutions could only work merely with slow Si-based semiconductors. / Ph. D. / Despite their mature technology and low manufacturing cost, the traditional Si-based power semiconductors had reached their limitations in operation from different points of view. The SiC MOSFETs which are the new generation of power semiconductors however seem to be able to shift the existing boundaries of operation for the Si-based semiconductors, resulting in significant improvement in design and operation of power electronics converters. This dissertation focuses on investigating the impact of emerging medium-voltage SiC MOSFETs on industrial motor drives, which consume over 28% of the total electricity used in the world. Firstly, the state-of-the-art non-commercial 3.3 kV SiC MOSFETs are characterized. Characterization of the devices is done to extract their key features such as switching and conduction losses, to enable loss calculation and performance evaluation in any target application. Since the mentioned devices are not commercial yet, the gate driving circuitry that can feature the best performance out of them are not commercially available either. Thus, the characterization process starts with design of an intelligent high-performance gate driver for the devices under test. Secondly, total of three topologies that are targeted for the study are discussed and their basics of operation is investigated. For this purpose the cascaded H-bridge, the modular multilevel converter and the 5-L active neutral point clamped converters are designed at three different voltage levels (4.16-, 6.9- and 13.8 kV) and two power levels (3- and 5 MVA). Selection of different voltage and power levels is done to enable comparison from different aspects as the operating point changes. Later, comparisons are done between the surveyed topologies designed at different operating points using different semiconductor technologies. The performed comparisons provide an unbiased input for the manufacturers and customers of these converters for selection of the target topology in motor drive application. Also to verify validity of the conducted simulations and calculations, a full-bridge converter cell is experimentally implemented using 3.3 kV 400 A SiC MOSFETs. Finally, a novel method is proposed for series-connecting lower-voltage SiC MOSFETs to reach higher-voltage devices. As of late 2017, the medium-voltage SiC MOSFETs are not commercially available. Also it is expected that upon commercialization, their price will be multiple times of that of low-voltage SiC MOSFETs. Thus, connecting lower-voltage SiC MOSFETs in series is an effective way of achieving higher-voltage devices and take advantage of superior properties if the SiC MOSFETs, while the availability and high cost problems are taken care of.

In the era of ever-increasing electrification, power-electronic converters play the crucial role of transforming electrical energy from one form to another. However, converters today face multiple challenges in meeting ever-growing demands for higher power density, broader operation ranges, and lower costs. The cost-benefits of economies of scale further emphasize the need for modular and scalable converters. While no single converter for high-power applications satisfies all criteria, the modular multilevel converter (MMC) emerges as the clear frontrunner. MMC is extremely modular, being developed using multiple smaller units or building blocks called power electronic building blocks (PEBBs) or submodules (SMs). The SMs are themselves developed using fast-switching low-voltage (LV) semiconductors meaningfully combined with energy storage components like capacitors or batteries. MMCs are highly modular and scalable and have a very broad operation range, making them a key solution already used today for a wide range of high-voltage applications like high-voltage direct-current (HVDC) transmission. However, the use of voluminous and heavy capacitors in SMs also makes MMCs much lower in power density compared to other similar voltage source converters (VSCs). Employing at least twice the number of devices compared to a conventional two-level VSC for the same ratings also increases the converter costs. These challenges have hindered MMC applications in medium-voltage (MV) and more power-dense HVDC systems. This research aims to overcome these limitations by enhancing MMCs in terms of power density, efficiency, and cost-effectiveness. These modifications would expand MMC's applications to much broader HV and MV markets. Three fundamental aspects are targeted to achieve such improvements: Topology, Components, and Controls. The first modification focuses on changing the topology by replacing some fast-switching LV-switch-based SMs with fewer low-frequency HV/MV switches. This greatly reduces the total number of components and, when combined with intelligent control, decreases costs and losses. The second modification focuses on components, proposing the replacement of fully controlled MV switches with more efficient and cost-effective but partially controlled ones like thyristors. Despite thyristors' historical controllability challenges, incorporating SMs can help resolve control challenges, creating a modular, scalable converter with a wide operation range, high power density, and lower costs. The third avenue explores advanced control strategies while maintaining the traditional MMC topology. By accelerating and precisely controlling the capacitor current, the SM capacitor energy, SM capacitor size can be significantly reduced. Although these control methods are complex, they offer potential improvements across all five criteria: modularity, scalability, power density, cost, and operational range. These innovations extend MMCs' applicability to emerging fields such as energy storage systems, electric vehicle charging stations, motor drives, and data centers. Moreover, these modifications enhance MMCs for traditional high-voltage direct-current transmission applications. The research emphasizes the advantages and addresses each modification's limitations, paving the way for a more efficient and versatile power electronics technology. / Doctor of Philosophy / In our electrically powered world, the unsung workhorse is the power(-electronic) converter. Power converters play the crucial role of transforming electrical energy from one form to another using switches that can turn on and off to accurately control the flow of electrical energy. Power converters are critical to integrating systems at different voltage, current, and power ratings. For instance, power converters enable low-power systems like cellphone chargers and high-power industrial drives to be integrated into the same interconnected power grid. However, these converters face challenges in adapting to the evolving demands of our modern world. The expectations from power converters are high – they need to be affordable, lightweight, and capable of processing large amounts of power in a compact size. Additionally, modularity and scalability are desired qualities to enable economies of scale and bring the total cost down. Yet, finding a converter that fulfills all these criteria remains a challenge. The modular multilevel converter (MMC) is a promising power converter developed to address most of these considerations. Currently employed in high-power, high-voltage applications such as transmitting energy over vast distances or linking power grids between countries, the MMC is constructed using smaller power units or building blocks called power electronic building blocks (PEBBs) or submodules (SMs). These SMs utilize fast-switching low-voltage switches along with energy storage components like capacitors or batteries. Despite its versatility, the MMC faces many limitations. The main challenge for MMCs is the inability to process more power in lower volume, commonly referred to as power density. The MMC power density is low due to the use of large capacitors or batteries. Additionally, it utilizes twice the number of switches compared to traditional non-modular power converters for the same rating, leading to higher costs. These challenges restrict its application in medium-voltage and power-dense high-voltage high-power systems. This research aims to address these challenges, focusing on enhancing the power density and cost-effectiveness of MMCs. Three key areas of MMC are targeted for improvement: topology, components, and controls. Firstly, MMC's structure is reimagined, replacing many low-voltage switches with fewer medium- or high-voltage, fully-controlled switches. Such a system is referred to as a hybrid MMC, and this reduces the converter volume and costs. This adjustment has the added benefit of making the converter more efficient. Secondly, the focus is also on the components used to develop hybrid MMCs. Instead of fully controlled medium- or high-voltage switches, partially controlled switches like thyristors provide advantages like lower losses and higher power ratings. However, these partially controlled switches have traditionally been very difficult to control. Despite historical controllability challenges, incorporating these partially controlled switches in conjunction with smart control of SMs addresses control issues, creating a modular, scalable converter with high power density and lower costs. The third enhancement involves fundamental improvements to MMC controls. By managing the energy flow to the capacitor at a much faster rate and precision than conventional methods, the size of a critical component can be significantly reduced, opening avenues for overall improvements. Furthermore, such fast control introduces additional challenges like active control in the face of non-idealities and higher losses. This dissertation further meaningfully addresses these challenges to develop a much more power-dense MMC. These improvements transform the MMC and its variants into a versatile power converter family that can extend much beyond traditional MMC applications of high-voltage transmission applications. With these modifications, the MMC can be further positioned as an excellent candidate to contribute towards energy storage systems, electric vehicle charging stations, industrial-level motor drives, dc microgrids, and data centers, meeting the diverse needs of our equally diverse and ever-more electrified world.

Multilevel converters are finding increased attention in industry and academia as the preferred choice of electronic power conversion for high power applications. They have a wide application area in a variety of industries involving transportation and energy management, a significant portion of which comprises of multilevel inverter fed induction motor drives. Multilevel inverters are ideally suitable for high power drives, since the switching frequency of the devices is limited for high power applications. In low power drives, the switching frequency is often in the range of tens of kHz, so that switching frequency harmonics are pushed higher in the frequency spectrum thereby the size and cost of the filter are reduced. But higher switching frequency has its own drawbacks, in particular for high voltage, high power applications. They cause large dv/dt stress on the motor and the devices, increased EMI problems and higher switching losses. An engineering trade-o is thus needed to select the minimum switching frequency without compromising on the output voltage quality. The present work is an alternate approach in this direction. Here, new inverter topologies and PWM strategies are developed that can eliminate a set of harmonics in the phase voltage using 12-sided polygonal space vector diagrams, also called dodecagonal space vector diagrams. A dodecagonal space vector diagram has many advantages over a hexagonal one. Switching space vectors on a dodecagon will not produce any harmonics of the order 6n 1, (n=odd) in the phase voltage. The next set of harmonics thus reside at 12n 1, (n=integer). By increasing the number of samples in a sector, it is also possible to suppress the lower order harmonics and a nearly sinusoidal voltage can be obtained. This is possible to achieve at a low switching frequency of the inverters. At the same time, a dodecagon is closer to a circle than a hexagon; so the linear modulation range is extended by about 6.6% compared to the hexagonal case. For a 50 Hz rated frequency operation, under constant V/f ratio, the linear modulation can be achieved upto a frequency of 48.3 Hz. Also, the harmonics of the order 6n 1, (n=odd) are absent in the over-modulation region. Maximum fundamental voltage is obtained from this inverter at the end of over-modulation region, where the phase voltage becomes a 12-step waveform. The present work is developed on dodecagonal space vector diagrams. The entire work can be summarized and explained through Fig. 1. This figure shows the development of hexagonal and dodecagonal space vector diagrams. It is known that, 3-level and 5-level space vector diagrams have been developed as an improvement over 2-level ones. They Figure 1: Development of hexagonal and dodecagonal space vector diagrams have better harmonic performance, reduced dv/dt stress on the motor and devices, better electromagnetic compatibility and improvement of efficiency over 2-level space vector diagrams. This happens because the instantaneous error between the reference vector and the switching vectors reduces, as the space vector density increases in the diagram. This is shown at the top of the figure. In the bottom part, the development of the dodecagonal space vector diagram is shown, which is the contribution of this thesis work. This is explained in brief in the following lines. Initially, a space vector diagram is proposed which switches on hexagonal space vectors in lower-modulation region and dodecagonal space vectors in the higher modulation region. As the reference vector length increases, voltage vectors at the vertices of the outer dodecagon and the vertices from the outer most hexagon is used for PWM control. This results in highly suppressed 5th and 7th order harmonics thereby improving the harmonic profile of the motor current. This leads to the 12-step operation at rated voltage where all the 5th and 7th order harmonics are completely eliminated. At the same time, the linear range of modulation extends upto 96.6% of base speed. Because of this, and the high degree of suppression of lower order harmonics, smooth acceleration of the motor upto rated speed is possible. The presence of multilevel space vector structure also limits the switching frequency of the inverters. In the next work, the single dodecagonal space vector diagram is improved upon to form two concentric dodecagons spanning the space vector plane (Fig. 1). The radius of the outer dodecagon is double the inner one. It reduces the device rating and the dv/dt stress on the devices to half compared to existing 12-sided schemes. The entire space vector diagram is divided into smaller sized isosceles triangles. PWM switching on these smaller triangles reduces the inverter switching frequency without compromising on the output voltage quality. The space vector diagram is further refined to accommodate six concentric dodecagons in the space vector plane (Fig. 1). Here the space vector diagram is characterized by alternately placed dodecagons which become closer to each other at higher radii. As such the harmonics in the phase voltage are reduced, in particular at higher modulation indices. At the same time, because of the dodecagonal space vector structure, all the 6n ± 1, (n=odd) harmonics are eliminated from the phase voltage. A nearly sinusoidal phase voltage can be generated without resorting to high frequency switching of the inverters. The above space vector diagrams are developed using different inverter circuits. The first work is developed from cascaded combination of three 2-level inverters, while the second and third works use 3-level NPC inverters feeding an open end induction motor drive. The circuit topologies are explained in detail in the respective chapters. Apart from this, PWM switching schemes and detailed analysis on duty cycle calculations using the concept of volt-second balance are also presented. They show that with proper switching schemes, the proposed configurations can substantially reduce the overall loss of the inverter. Other operational issues like capacitor voltage balancing of 3-level NPC inverters and improvement of input current drawn from the grid are also covered. All the above propositions are first simulated by MATLAB and subsequently verified by an experimental laboratory prototype. Motor current waveforms both at steady state and transient conditions during motor acceleration show that the induction motor can be fed from nearly sinusoidal voltage at all operating conditions. Simplified comparative studies are also made with the proposed converters and higher level inverters in terms of output voltage quality and losses. These are some of the constituents for chapters 2, 3 and 4 in this thesis. Additionally, the first chapter also covers a brief survey on some of the recent progresses made in the field of multilevel inverter. The thesis concludes with some interesting ideas for further thought and exploration.

This thesis deals with modeling, simulation and implementation of Load Commutated SCR based current source Inverter (LCI) fed squirrel cage induction motor drive with sinusoidal voltage and sinusoidal current. In the proposed system, the induction motor is fed by an LCI. A three level diode clamped voltage source inverter (VSI) is connected at the motor terminal with ac chokes connected in series with it. The VSI currents are controlled in such a manner that it injects the reactive current demanded by the induction motor and the LCI for successful commutation of the SCRs in the LCI. Additionally, it absorbs the harmonic frequency currents to ensure that the induction motor draws sinusoidal current. As a result, the nature of the motor terminal voltage is also sinusoidal. The concept of load commutation of the SCRs in the LCI feeding an induction motor load is explained with necessary waveforms and phasor diagrams. The necessity of reactive compensation by the active filter connected at the motor terminal for the load commutation of the thyristors, is elaborated with the help of analytical equations and phasor diagrams. The requirement of harmonic compensation by the same active filter to achieve sinusoidal motor current and motor voltage, is also described. Finally, to achieve the aforementioned induction motor drive, the VA ratings of the active filter (VSI) and the CSI with respect to VA rating of the motor, are determined theoretically. The proposed drive scheme is simulated under idealized condition. Simulation results show good steady state and dynamic response of the drive system. Load commutation of the SCRs in the LCI and the sinusoidal profile of motor current and voltage, have been demonstrated. As in LCI fed synchronous motor drives, a special mode of operation is required to run up the induction motor from standstill. As the SCRs of the LCI are load commutated, they need motor terminal voltages for commutation. At standstill these voltages are zero. So, a starting strategy has been proposed and adopted to start the motor with the aid of the current controlled VSI to accelerate until the motor terminal voltages are high enough for the commutation of the SCRs in the LCI. The proposed drive is implemented on an experimental setup in the laboratory. The IGBT based three level diode clamped VSI has been fabricated following the design of the standard module in the laboratory. A generalized digital control platform is also developed using a TMS320F2407A DSP. Two, three phase thyristor bridges with necessary firing pulse circuits have been used as the phase controlled rectifier and the LCI respectively. Appropriate protection scheme for such a drive is developed and adopted to operate the drive. Relevant experimental results are presented. They are observed to be in good agreement with the simulation results. The effect of capacitors connected at the output of the LCI in the commutation process of the SCRs in the LCI is studied and analyzed. From the analysis, it is understood that the capacitors form a parallel resonating pair with filter inductor and the motor leakage inductance, which results in an undesired oscillation in the terminal voltage during each of the commutation intervals leading to commutation failure. So, in the final system, the capacitors are removed to eliminate any chance of commutation failure of the SCRs in the LCI. It is shown by experiment that the commutation of the SCRs takes place reliably in the absence of the capacitors also. The commutation process is studied and analyzed without the capacitors to understand the motor terminal voltage waveform of the experimental results.

This thesis is an effort to investigate the operation and the performanceof modular multilevel converters (M2Cs). Proven to be the most promisingtopology in high-voltage high-power applications, it is necessary to put aneffort in understanding the physical laws that govern the internal dynamicsof such converters, in order to design appropriate control methods. AlthoughM2Cs belong to the well-studied family of voltage-source converters (VSCs),and claim a modular structure, their control is significantly more complicatedcompared to two- or three-level VSCs, due to the fact that a much highernumber of switches and capacitors are needed in such a topology. This thesishighlights the important parameters that should be considered when designingthe control for an M2C, through analyzing its internal dynamics, and alsosuggests ways to control such converters ensuring stable operation withoutcompromising the performance of the converter.Special focus is given on ac motor-drive applications as they are very demandingand challenging for the converter performance. Interactions betweenthe internal dynamics and the dynamics of the driven motor are experimentallyinvestigated. The problem of operating the converter when connectedto a motor standing still is visited, even under the condition that a greatamount of torque and current are requested, in order to provide an idea forthe converter requirements under such conditions. Finally, an optimization ofthe converter operation is suggested in order to avoid overrating the convertercomponents in certain operation areas that this is possible.All analytical investigations presented in this thesis are confirmed by experimentalresults on a laboratory prototype converter, which was developedfor the purposes of this project. Experimental verification proves the validityof the theoretical investigations, as well as the correct performance of thecontrol methods developed during this project on a real, physical converter,hoping that the results of this thesis will be useful for large-scale implementations,in the mega- or even giga-watt power range. / Denna avhandling är ett försök att undersöka drift och egenskaper avmodulära multinivåomvandlare (M2C:er). Eftersom denna topologi anses varaden mest lovande inom högspänings-högeffekt-tillämpningar är, och somett underlag för att kunna formulera lämpliga styrmetoder, är det nödvändigtatt lägga kraft i att försöka förståde fysikaliska lagar som styr den inredynamiken i sådana omvandlare. Även om M2C:erna tillhör den välstuderadefamiljen av spänningsstyva omvandlare (VSC:er), och har en modulärstruktur, är deras reglering avsevärt mer komplicerad jämfört med två- ellertre-nivåomvandlare, eftersom ett mycket större antal switchar och kondensatorerär nödvändiga i en sådan topologi. Denna avhandling sätter fingretpå de parametrar som måste beaktas när man konstruerar regleringen för enM2C, genom att analysera den interna dynamiken, samt att föreslå sätt attstyra sådana omvandlare såatt stabil drift kan säkerställas utan att negativtpåverka prestanda.Ett speciellt fokus läggs på växelströmsmotordrifter eftersom de är särskiltutmanande vad gäller prestanda. Växelverkan mellan den interna dynamikenoch motorns dynamik undersöks experimentellt. Problemet att driva motornvid stillestånd behandlas även i fallet med hög ström och högt moment för atterhålla kunskap om kraven påomvandlaren i sådana fall. Slutligen föreslås enoptimering av omvandlarens drifttillstånd för att undvika överdimensioneringav omvandlarens komponenter i de fall detta är möjligt.Alla analytiska undersökningar som läggs fram i denna avhandling är bekräftadegenom experimentella resultat från en laboratorieomvandlare, somutvecklats inom ramen för detta arbete. Den experimentella verifieringen bevisargiltigheten av alla teoretiska undersökningar. Den visar också på demycket goda prestanda som de utvecklade styrmetoderna har vid drift aven verklig fysisk omvandlare. Förhoppningen är att resultaten från detta arbetekan komma till använding i storskaliga implementerinar i mega- ellergiga-wattklassen. / <p>QC 20141201</p>

Multilevel converters have become the direct accepted solution for high power converter applications. They are used in wide variety of power electronic applications like power transmission and distribution, electric motor drives, battery management and renewable energy management to name a few. For medium and high voltage motor drives, especially induction motor drives, the use of multilevel voltage source inverters have become indispensible. A high voltage multilevel inverter could be realized using low voltage switching devices which are easily available and are of low cost. A multilevel inverter generates voltage waveforms of very low harmonic distortion by switching between voltage levels of reasonably small amplitude differences. Thus the dv/dt of the output voltage waveform is small and hence the electromagnetic interference generated is less. Because of better quality output generation, the switching frequency of the multilevel inverters could be reduced to control the losses. Thus, a multilevel converter stands definitely a class apart in terms of performance from a conventional two-level inverter. Many multilevel inverter topologies for induction motor drives are available in the literature. The basic multilevel topologies are the neutral point clamped (NPC) inverter, flying capacitor (FC) inverter and the cascaded H-bridge (CHB) inverter. Various other hybrid multilevel topologies have been proposed by using the basic multilevel inverter topologies. It is also possible to obtain multilevel output by using conventional two-level inverters feeding an open-end winding induction motor from both sides. All the conventional multilevel voltage source inverters generate hexagonal (6 sided polygons) voltage space vector structures. When an inverter with hexagonal space vector structure is operated in the over modulation range, significant low order harmonics are generated in the phase voltage output. Over modulation operation is required for the full utilization of the available DC-link voltage and hence maximum power generation. Among the harmonics generated, the fifth and seventh harmonics are of significant magnitudes. These harmonics generate torque ripple in the motor output and are undesirable in high performance motor drive applications. The presence of these harmonics further creates problems in the closed loop current control of a motor, affecting the dynamic performance. Again, the harmonic currents generate losses in the stator windings. Therefore, in short, the presence of harmonic voltages in the inverter output is undesirable. Many methods have been proposed to eliminate or mitigate the effect of the harmonics. One solution is to operate the inverter at high switching frequency and thereby push the harmonics generated to high frequencies. The stator leakage inductance offers high impedance to the high frequency harmonics and thus the harmonic currents generated are negligible. But, high switching frequency brings switching losses and high electromagnetic interference generation in the drive system. And also, high switching frequency operation is effective only in the linear modulation range. Another solution is to use passive harmonic filters at the inverter output. For low order harmonics, the filter components would be bulky and costly. The loss created by the filters degrades the efficiency of the drive system as well. The presence of a filter also affects the dynamic performance of the drive system during closed loop operation. Special pulse width modulation (PWM) techniques like selective harmonic elimination (SHE) PWM can prevent the generation of a particular harmonic from the phase voltage output. The disadvantages of such schemes are limited modulation index, poor dynamic performance and extensive offline computations. An elegant harmonic elimination method is to generate a voltage space vector structure having more number of sides like a dodecagon (12 sided polygons) or an octadecagon (18 sided polygons) rather than a hexagon. Inverter topologies generating dodecagonal voltage space vector structure eliminate fifth and seventh order harmonics, represented as 6n 1; n = odd harmonics, from the phase voltages and hence from the motor phase currents, throughout the entire modulation range. The first harmonics appearing the phase voltage are the 11th and 13th harmonics. Another advantage is the increased linear modulation range of operation for a given DC-link voltage, because geometrically dodecagon is closer to circle than a hexagon. An octadecagonal structure eliminates the 11th and 13th harmonics as well from the phase voltage output. The harmonics present in the phase voltage are of the order 18n 1; n = 1; 2; 3; :::. Thus the total harmonics distortion (THD) of the phase voltage is further improved. The linear modulation range also gets enhanced compared to hexagonal and dodecagonal structures. Multilevel dodecagonal and octadecagonal space vector structures combines the advantages of both multilevel structure and dodecagonal and octadecagonal structure and hence are very attractive solutions for high performance induction motor drive schemes. Chapter 1 of this thesis introduces the multilevel in-verter topologies generating hexagonal, dodecagonal and octadecagonal voltage space vector structures. Inverter topologies generating multilevel dodecagonal and octadecago-nal voltage space vector structures have been proposed before but using multiple DC sources delivering active power. The presence of more than one DC source in the inverter topology makes the back to back operation (four-quadrant operation) of the drive system difficult. And also the drive system becomes more costly and bulky. This thesis proposes induction motor drive schemes generating multilevel dodecagonal and octadecagonal volt-age space vector structures using a single DC source. In Chapter 2, an induction motor drive scheme generating a six-concentric multilevel dodecagonal voltage space vector structure using a single DC source is proposed for an open-end winding induction motor. In the topology, two three-level inverters drive an open-end winding IM, one inverter from each side. DC-link of primary inverter is from a DC source (Vdc) which delivers the entire active power, whereas the secondary inverter DC-link is maintained by a capacitor at a voltage of 0:289Vdc, which is self-balanced during the inverter operation. The PWM scheme implemented ensures low switching frequency for primary inverter. Secondary inverter operates at a small DC-link voltage. Hence, switching losses are small for both primary and secondary inverters. An open-loop V/f scheme was used to test the topology and modulation scheme. In the work proposed in Chapter 3, the topology and modulation scheme used in the first work is modified for a star connected induction motor. Again, the scheme uses only a single DC source and generates a six-concentric multilevel space vector struc-ture. The power circuit topology is realized using a three-level flying capacitor (FC) inverter cascaded with an H-bridge (CHB). The capacitors in the CHB inverter are maintained at a voltage level of 0:1445Vdc. The FC inverter switches between volt-age levels of [Vdc; 0:5Vdc; 0] and the CHB inverter switches between voltage levels of [+01445Vdc; 0; 0:1445Vdc]. The PWM scheme generates a quasi-square waveform output from the FC inverter. This results in very few switchings of the FC inverter in a funda-mental cycle and hence the switching losses are controlled. The CHB inverter switches Ch. 0: at high frequency compared to the FC inverter and cancels the low order harmonics (6n 1; n = odd) generated by the FC inverter. Even though the CHB operates at higher switching frequency, the switchings are at low voltage thereby controlling the losses. The linear modulation range of operation is extended to 48:8Hz for a base frequency of 50Hz. An open-loop V/f scheme was used to test the topology and modulation scheme. In Chapter 4, a nine-concentric multilevel octadecagonal space vector structure is proposed for the first time, again using a single DC source. The circuit topology remains same as the work in Chapter 3, except that the CHB capacitor voltage is maintained at 0:1895Vdc. The 5th; 7th; 11th and 13th harmonics are eliminated from the phase voltage output. The linear modulation range is enhanced to 49:5Hz for a base speed of 50Hz. An open-loop V/f scheme and rotor field oriented control scheme were used to test the proposed drive system. All the proposed drive schemes have been extensively simulated and tested in hard-ware. Simulation was performed in MATLAB-SIMULINK environment. For implement-ing the inverter topology, SKM75GB12T4 IGBT modules were used. The control al-gorithms were implemented using a DSP (TI’s TMS320F28334) and an FPGA (Xilinx Spartan XC3S200). A 1kW , 415V , 4-pole induction motor was used for the experiment purpose. The above mentioned induction motor drive schemes generate phase voltage outputs in which the low order harmonics are absent. The linear modulation range is extended near to the base frequency of operation compared to hexagonal space vector structure. In the inverter topologies, the secondary inverters or the CHB inverters functions as harmonic filters and delivers zero active power. The primary inverter in the topologies switches at low frequency, reducing the power loss. Single DC source requirement brings down the cost of the system as well as permitting easy four-quadrant operation. This is also advantageous in battery operated systems like EV applications. With these features and advantages, the proposed drive schemes are suitable for high performance, medium voltage induction motor drive applications.

MULTILEVEL inverters are the preferred choice of converters for electronic power conversion for high power applications. They are gaining popularity in variety of industrial applications including electric motor drives, transportation, energy management, transmission and distribution of power. A large portion of energy conversion systems comprises of multilevel inverter fed induction motor drives. The multilevel inverters are ideal for such applications, since the switching frequency of the devices can be kept low. In conventional two level inverters, to get nearly sinusoidal phase current waveform, the switching frequency of the inverter is increased and the harmonics in the currents are pushed higher in the frequency spectrum to reduce the size and cost of the filters. But higher switching frequency has its own drawbacks – in particular for medium voltage, high power applications. They cause large dv_/ dt stresses on the motor terminals and the switching devices, leading to increased electromagnetic interference (EMI) problems and higher switching losses. Harmonics in the motor currents can further be minimized by adopting dodecagonal voltage space vector (SV) switching (12-sided polygon). In case of dodecagonal SV switching, the fifth and seventh order (6n , 1, n = odd) harmonics are completely eliminated for the full modulation range including over modulation and twelve step operation in the motor phase voltages and currents. In addition to low order harmonic current suppression, the linear modulation range for dodecagonal SV switching is also more by 6% when compared to that of the conventional hexagonal SV switching. The dodecagonal voltage SV structure is made possible by connecting two inverters with DC-link voltages Vd and 0:366Vd on either side of an open-end winding induction motor. The dodecagonal space vector switching can be used to produce better quality phase voltage and current waveforms and overcome the problem of low order fifth and seventh harmonic currents and to improve the range for linear modulation while reducing the switching frequency of the inverters when compared to that of the conventional hexagonal space vector based inverters. This thesis focuses on three aspects of multilevel dodecagonal space vector structures (i) Two new power circuit topologies that generate a multilevel dodecagonal voltage space vector structure with symmetric triangles, (ii) A multilevel dodecagonal SV structure with nineteen concentric dodecagons, (iii) Pulse width modulation (PWM) timing calculation methods for a general N-level dodecagonal SV structure. (i) Two new power circuit topologies capable of generating multilevel dodecagonal voltage space vector structure with symmetric triangles with minimum number of DC link power supplies and floating capacitor H-bridges are proposed. The first power topology is composed of two hybrid cascaded five level inverters connected to either side of an open end winding induction machine. Each inverter consists of a three level neutral point clamped (NPC) inverter, cascaded with an isolated capacitor fed H-bridge making it a five level inverter. The second topology is a hybrid topology for a normal induction motor (star or delta connected), where the power is fed to the motor only from one side. The proposed scheme retains all the advantages of multilevel topologies as well the advantages of the dodecagonal voltage space vector structure. Both topologies have inherent capacitor balancing for floating H-bridges for all modulation indices including transient operations. The proposed topologies do not require any pre-charging circuitry for startup. PWM timing calculation method for space vector modulation is also explored in this chapter. Due to the symmetric arrangement of congruent triangles within the voltage space vector structure, the timing computation requires only the sampled reference values and does not require any iterative searching, off-line computation, look-up tables or angle estimation. Experimental results for steady state operation and transient operation are also presented to validate the proposed concept. (ii) A multilevel dodecagonal voltage space vector structure with nineteen concentric do-decagons is proposed for the first time. This space vector structure is achieved by connecting two sets of asymmetric hybrid five level inverters on either side of an open-end winding induction motor. The dodecagonal structure is made possible by proper selection of DC-link voltages and switching states of the inverters. In addition to that, a generic and simple method for calculation of PWM timings using only sampled reference values (v and v ) is proposed. This enables the scheme to be used for any closed loop application like vector control. Also, a new switching technique is proposed which ensures minimum switching while eliminating the fifth and seventh order harmonics and suppressing the eleventh and thirteenth harmonics, eliminating the need for bulky filters. The motor phase voltage is a 24-stepped waveform for the entire modulation range thereby reducing the number of switchings of the individual inverter modules. Experimental results for steady state operation, transient operation including start-up have been presented and the results of Fast Fourier Transform (FFT) analysis is also presented for validating the proposed concept. (iii) A method to obtain PWM timings for a general N-level dodecagonal voltage space vector structure using only sampled reference values is proposed. Typical methods that are used to find PWM timings for dodecagonal SV structures use modulation index and the reference vector angle, to get the timings T1 and T2 using trigonometric calculations. This method requires look-up tables and is difficult to implement in closed loop systems. The proposed method requires only two additions to compute these timings. For multilevel case, typical iterative methods need timing calculations (matrix multiplications) to be performed for each triangle. The proposed method is generic and can be extended to any number of levels with symmetric structures and does not require any iterative searching for locating the triangle in which the tip of the reference vector lies. The algorithm outputs the triangle number and the PWM timing values of T0, T1 and T2 which can be set as the compare values for any carrier based PWM module to obtain space vector PWM like switching sequences. Simulation and experimental results for steady state and transient conditions have been presented to validate the proposed method. A 3.7 kW, 415 V, 50 Hz, 4-pole open-end winding induction motor was used for the experimental studies. The semiconductor switches that were used to realize the power circuit for the experiment were 75 A, 1200 V insulated-gate bipolar transistor (IGBT) half-bridge modules (SKM75GB12T4). Opto-isolated gate drivers with desaturation protection (M57962L) were used to drive the IGBTs. For the speed control and PWM timing computation a digital signal processor (DSP-TMS320F28335) with a clock frequency of 150 MHz was used. For modulation frequencies 10 Hz and below, a constant sampling frequency of 1 kHz was used as the frequency modulation ratio is high. For modulation frequencies above 10 Hz, synchronous PWM strategy was used. The time duration Ts is the sampling interval for which the timings T1 , T2 and T0 are calculated. As in the case of any synchronous PWM method, the duration of sampling time (Ts) is a function of the fundamental frequency of the modulating signal. In this case, Ts = 1_.fm • 12n) sec. where fm is fundamental frequency in Hertz and ‘n’ is the number of samples per 30ý dodecagonal sector. The PWM timings and the triangle data (from the DSP) is fed to field programmable gate array (FPGA) (SPARTAN XC3S200) clocked at 50 MHz where the actual gating pulses are generated. The capacitor balancing algorithm and the dead-time modules were implemented within FPGA. No external hardware was used for generation of dead-time. The dead-time block generates a constant dead-time of 2 s for all the switches. Extensive testing was done for steady state operations and transient operations including quick acceleration and start-up to validate the proposed concepts. With the advantages like extension of linear modulation range, elimination of fifth and seventh harmonics in phase voltages and currents for the full modulation range, suppression of eleventh and thirteenth harmonics in phase voltages and currents, reduced device voltage ratings, lesser dv_dt stresses on devices and motor phase windings, lower switching frequency, inherent cascaded H-bridge (CHB) capacitor balancing, the proposed space vector structures, the inverter power circuit topologies, the switching techniques and the PWM timing calculation methods can be considered as viable schemes for medium voltage, high power motor drive applications.

Thesis (PhD)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: The position sensorless controllability of the reluctance synchronous machine (RSM) is investigated in this thesis with the focus on industry applications where variable and dynamic torque is required from startup up to rated speed. Two low speed as well as one medium to high speed position sensorless control (PSC) method for RSMs are investigated. These methods are extended to operate in the entire rated speed region with a hybrid PSC structure that makes use of phase locked-loop synchronisation and a hysteresis changeover method. It is shown in this thesis that PSC of the lateral rib rotor RSM is not possible from zero up to ± 0.2 p.u current. It is shown through finite element (FE) simulations that PSC of the ideal rotor RSM however, is possible at zero reference current. A novel construction method is used to build two ideal rotor RSMs. Measured flux linkage curve results of the ideal rotor RSMs correlate well with simulation results and it is shown that the electrical angle of the machine can be tracked successfully at zero reference current. The FE simulation package is used to compare the saliency of the RSM on a per-unit scale to three types of field intensified permanent magnet (FI-PM) synchronous machines and a field weakening interior permanent magnet synchronous machine. It is shown that the saliency of the RSM is larger than that of the investigated PM machines from zero up to rated load. It is thus concluded that the RSM is well suited to saliency-based PSC (SB-PSC) methods, which are used to control synchronous machines at startup and low speeds. The hybrid PSC methods developed in this thesis, are tested and evaluated on three proposed industry applications. The first is a reluctance synchronous wind generator with an inverter output LC filter. The LC filter allows long cables to be used and reduces the voltage stress on the stator windings of the machine. The combination of the LC filter and hybrid PSC method allows the power electronics and controller to be stationed in the base of the turbine tower. A new stator quantity estimation method is derived to omit the need of current and voltage sensors on the machine side of the LC filter. Good maximum power point tracking laboratory results are shown with the high frequency injection-assisted hybrid PSC method. The second application investigated is a position sensorless controlled variable gear electric vehicle (EV) RSM drive. Simulation and measured results show good torque capabilities of the position sensorless controlled EV RSM. It is shown through simulation results that the fundamental current harmonic is dominant in the demodulation scheme of the high frequency injection position sensorless control (HFIPSC) method due to the high current rating of the proposed RSM. The HFI-PSC method is extended to reduce the effect of the fundamental current harmonic in the demodulation scheme without adding any additional filters. The final investigated application is a novel mine scraper winch, which uses two position sensorless controlled RSMs to retrieve ore from the blast site underground. The new design improves on the safety, efficiency and durability of the current scraper winch design. Measured results show that the position sensorless controlled winch RSM is able to deliver rated startup torque with both investigated SB-PSC methods. Finally an automation method is implemented and tested to limited the applied force on the scraper and automatically free itself when stuck. / AFRIKAANSE OPSOMMING: Die posisie sensorlose beheer eienskappe van die reluktansie sinchroonmasjien (RSM) word in hierdie tesis ondersoek met die fokus op industriële toepassings waar varierende dinamiese draaimoment vereis word vanaf stilstand tot by ken spoed. Twee lae spoed- en een ho¨e spoed posisie sensorlose beheer (PSB) metodes vir RSMe is ondersoek. Hierdie metodes is uitgebrei om twee hibriede PSB metodes to skep wat die RSM van stilstand tot by kenspoed posisie sensorloos kan beheer. Die ontwikkelde hibriede metodes maak gebruik van ’n histerese oorskakelings skema en fase geslote lus sinchronisasie Daar word in hierdie tesis bevestig dat die laterale rib RSM nie beheer kan word met die geondersoekte PSB metodes by nul stroom nie. Eindige element simulasie resultate wys egter daarop dat die ideale rotor RSM wel beheer kan word met die geondersoekte metodes by nul stroom. ’n Nuwe konstruksie metode is voorgestel om twee ideale rotor RSMe to bou. Gemete vloed omsluiting kurwes resultate korreleer baie goed met dié van die eindige element simulasies. Gemete resultate wys ook daarop dat PSB van die nuwe masjiene moontlik is by nul stroom. ’n Eindige element pakket is gebruik om die speek-koëffissiënt van die RSM te vergelyk met drie tipes veld-versterkte permanent magneet masjiene, asook een veld verswakte permanent magneet versinkte masjien. Die simulasie resultate wys dat die RSM se speek-koëffissiënt hoër is as die van die geondersoekte permanent magneet masjiene. Die RSM is dus geskik vir speek-koëffissiënt georienteerde PSB metodes, wat hoofsaaklik by stilstand en lae spoed gebruik word. Die ontwikkelde hibried PSB metodes is getoets en geëvalueer met drie voorgestelde industriële toepassings. Die eerste is ’n reluktansie sinchroon wind generator met ’n omsetter uittree laagdeurlaat filter. Die laagdeurlaat filter laat toe dat langer kabels vanaf die omsetter na die generator gebruik kan word. Die kombinasie van die laagdeurlaat filter en die PSB metodes laat toe dat die drywingselektronika en die beheerders in die toring basis geplaas kan word. Dit kan die gewig van die nasel verminder. Goeie maksimum drywingspunt volging laboratorium resultate word getoon met die hoë frekwensie ondersteunde hibried PSB metode. Die tweede geondersoekte toepassing is ’n posisie sensorlose beheerde, varierende ratkas elektriese voertuig RSM. Goeie simulasie en gemete draaimoment resultate van die RSM word getoon. Simulasie resultate toon dat die fundamentele q-as stroom harmoniek dominant is in die demodulasie skema van die hoë frekwensie PSB metode, as gevolg van die hoë ken stroom van die motor. Die hoë frekwensie PSB metode is uitgebrei om die fundamentele stroom harmoniek te onderdruk in die demodulasie skema sonder om enige filters by te voeg. Die finale toepassing is ’n nuwe myn windas wat van twee posisie sensorlose beheerde RSMe gebruik maak om klippe ondergronds te verplaas vanaf die ontploffings area. Die voorgestelde ontwerp verbeter die huidige ontwerp ten opsigte van die veiligheid, energie effektiwiteit en robuustheid. Gemete resultate wys dat ken draaimoment moontlik is met altwee speek-koëffissiënt metodes. ’n Automasie metode, wat die maksimum draaimoment op die windas beperk en automaties homself bevry indien hy vasval, is voorgestel en geëvalueer.

Die Zeiten der Plattensammlung sind vorbei, Kassetten und CDs sind der MP3-Datei gewichen und nun wird Musik ausschließlich gestreamt. Dieses Zukunftsszenario ist bis dato noch nicht eingetreten, aber wird dies überhaupt passieren? Wird der Kauf von physischen Musikdatenträgern und digitalen Musikdateien dank der immer stärker ansteigenden Streaming Aktivitäten komplett eingestellt? Oder können beide Formen nebeneinander existieren? Um diesen Fragen auf den Grund zu gehen, wurde im Rahmen dieser Arbeit eine Umfrage mit 1.661 Studenten der Technischen Universität Dresden durchgeführt. Die Ergebnisse geben Aufschluss über die Nutzungshäufigkeiten von kostenfreien und kostenpflichtigen Streaming Anbietern sowie von CDs / Schallplatten und MP3 Musikdateien. Zudem wird aufgezeigt, dass eine geringe Zahlungsbereitschaft bei den Studenten besteht. Es werden bereits selten mehr als 5 € in Musik investiert, doch seitdem die Studenten Streaming Dienste nutzen, geben sie nach eigenen Angaben noch weniger Geld für Musik aus als zuvor. Diesem Negativtrend steht die Erkenntnis gegenüber, dass die Probanden seit der Nutzung von Streaming Angeboten weniger Musik illegal herunterladen. Auch wenn der Großteil weniger Musik kauft, so ist es etwa der Hälfte aller Befragten sehr wichtig, Musik zu besitzen, vor allem in physischer Form. Zudem wurden Nutzungsmotive der Möglichkeiten des Musikhörens erfasst, um deren Stärken und Schwächen aufzuzeigen. Die Ergebnisse verdeutlichen, dass die kostenfreie Variante des Streamens zwar häufig genutzt wird, sich die traditionellen Musikdatenträger und Musikdateien jedoch immer noch großer Beliebtheit erfreuen. Von einer kompletten Verdrängung des Kaufens von Musik kann demnach nicht ausgegangen werden.

Les travaux de recherche présentés dans ce mémoire concernent des contributions à l'identification paramétrique de modèles à temps continu. La première contribution est le développement d'une méthode à erreur de sortie appliquée à des modèles linéaires, en boucle ouverte et en boucle fermée. Les algorithmes sont présentés pour des modèles à temps continu, en utilisant une approche hors ligne ou récursive. La méthode est étendue à l'identification de systèmes linéaires comprenant un retard pur. La méthode développée est appliquée à différents systèmes et comparée aux méthodes d'identification existantes. La deuxième contribution est le développement d'une nouvelle approche d'identification de systèmes à boucles imbriquées. Cette approche est développée pour l'identification de systèmes électromécaniques. Elle se base sur l'utilisation d'un modèle d'identification paramétrique générique d'entraînements électromécaniques en boucle fermée, sur la connaissance du profil des lois de mouvement appliquées appelées excitations, et sur l'analyse temporelle de signaux internes et leurs corrélations avec les paramètres à identifier. L'approche est développée dans le cadre de l'identification d'entraînements à courant continu et synchrone. L'application de cette approche est effectuée au travers de simulations et de tests expérimentaux. Les résultats sont comparés à des méthodes d'identification classiques. / The research works presented in this thesis are about contributions in continuous time model parametric identication. The rst work is the development of an output error method applied on linear models, in open and closed loop. The algorithms are presented for continuous time models, using in-line or oine approaches. The method is extended to the case of the linear systems containing pure time delay. The developed method is applied to several systems and compared to the best existing methods. The second contribution is the development of a new identication approach for cascaded loop systems. This approach is developed for identifying electromechanical systems. It is based on the use of a generic parametric model of electromechanical drives in closed loop, on the knowledge of the movement laws applied and called excitations, and on the analyse of the time internal signals and their correlations with the parameters to identify. This approach is developed for identifying direct current and synchronous drives. The approach is applied with simulations and experimental tests. The obtained results are compared to best identifying known methods.