This thesis comprises tribological studies of extremely well-defined surfaces of different designs. Both low-friction and high-friction surfaces were manufactured and experimentally evaluated. In the low-friction studies, lithography and anisotropic etching of silicon was first used as a texturing technique. The textured surfaces were subsequently PVD coated with TiN or DLC to achieve tribologically relevant interfaces. The results showed that under starved lubricated conditions, fine surface textures lowered the coefficient of friction and the wear rate. It was shown that also the orientation of the texture is of major importance for the lubricating function. Further, a novel embossing technique was developed, permitting texturing of steel and other materials. A micro mechanically designed diamond tool was used to emboss steel surfaces. The roller/piston contact from a hydraulic motor was simulated and introduction of an embossed texture on the piston decreased the level and the fluctuation of the friction. The effect of the texture was here similar to the effect of an additional polish step. However, in general it is not an easy task to substantially improve a boundary lubricated contact by introducing a texture. Studies of high friction surfaces were performed on micro mechanically designed diamond surfaces equipped with sharp pyramids or ridges. Just as theory predicts, the coefficient of friction was dependent on the shape of the ploughing bodies, but not on the counter material or the load. The tested surfaces resulted in static coefficients of friction between 1.1 and 1.6, depending on surface design and orientation. These are extremely high values, and therefore very interesting for practical applications requiring a high static friction. Conclusively, the present thesis shows that it is possible to design and produce surfaces both for improved lubrication in sliding contact and for substantially improved high friction performance in static contacts.

Among the materials that can be treated in order to impart superhydrophobic properties are many originally hydrophilic metals. For this, they must undergo a sequential treatment, including roughening and hydrophobic coating. This contribution presents various preparation routes along with various characterization methods, such as dynamic contact angle (DCA) measurements, scanning electron microscopy (SEM) and spectroscopic techniques (FT–IRRAS, XPS, EIS). Micro-rough surfaces of pure and alloyed aluminum were generated most easily by using a modifie Sulfuric Acid Anodization under Intensifie conditions (SAAi). This produces a micro-mountain-like oxide morphology with peak-to-valley heights of 2 μm and sub-μm roughness components. Additionally, micro-embossed and micro-blasted surfaces were investigated. These micro-roughened initial states were chemically modifie with a solution of a hydrophobic compound, such as the reactive f uoroalkylsilane PFATES, the reactive alkyl group containing polymer POMA, or the polymer Teflo ® AF. Alternatively, the chemical modificatio was made by a Hot Filament Chemical Vapor Deposition (HFCVD) of a PTFE layer. The latter can form a considerably higher thickness than the wet-deposited coatings, without detrimental leveling effects being observed in comparison with the original micro-rough surface. The inherent and controllable morphology of the PTFE layers represents an important feature. The impacts of a standardized artificia weathering (WTH) on the wetting behavior and the surface-chemical properties were studied and discussed in terms of possible damage mechanisms. A very high stability of the superhydrophobicity was observed for the f uorinated wet-deposited PFATES and Teflo ® AF coatings as well as for some of the PTFE layer variants, all on SAAi-pretreated substrates. Very good results were also obtained for specimens produced by appropriate mechanical roughening and PTFE coating.

Made available in DSpace on 2014-12-17T14:55:05Z (GMT). No. of bitstreams: 1 WilfredoBF_TESE.pdf: 4144764 bytes, checksum: ae0670814eb6793d7e5af7d0973a9f65 (MD5) Previous issue date: 2012-03-26 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior / Several research lines show that sleep favors memory consolidation and learning. It has been proposed that the cognitive role of sleep is derived from a global scaling of synaptic weights, able to homeostatically restore the ability to learn new things, erasing memories overnight. This phenomenon is typical of slow-wave sleep (SWS) and characterized by non-Hebbian mechanisms, i.e., mechanisms independent of synchronous neuronal activity. Another view holds that sleep also triggers the specific enhancement of synaptic connections, carrying out the embossing of certain mnemonic traces within a lattice of synaptic weights rescaled each night. Such an embossing is understood as the combination of Hebbian and non-Hebbian mechanisms, capable of increasing and decreasing respectively the synaptic weights in complementary circuits, leading to selective memory improvement and a restructuring of synaptic configuration (SC) that can be crucial for the generation of new behaviors ( insights ). The empirical findings indicate that initiation of Hebbian plasticity during sleep occurs in the transition of the SWS to the stage of rapid eye movement (REM), possibly due to the significant differences between the firing rates regimes of the stages and the up-regulation of factors involved in longterm synaptic plasticity. In this study the theories of homeostasis and embossing were compared using an artificial neural network (ANN) fed with action potentials recorded in the hippocampus of rats during the sleep-wake cycle. In the simulation in which the ANN did not apply the long-term plasticity mechanisms during sleep (SWS-transition REM), the synaptic weights distribution was re-scaled inexorably, for its mean value proportional to the input firing rate, erasing the synaptic weights pattern that had been established initially. In contrast, when the long-term plasticity is modeled during the transition SWSREM, an increase of synaptic weights were observed in the range of initial/low values, redistributing effectively the weights in a way to reinforce a subset of synapses over time. The results suggest that a positive regulation coming from the long-term plasticity can completely change the role of sleep: its absence leads to forgetting; its presence leads to a positive mnemonic change / Diversas linhas de pesquisa demonstram que o sono favorece a consolida??o de mem?rias e o aprendizado. Tem sido proposto que o papel cognitivo do sono deriva de um redimensionamento global dos pesos sin?pticos, capaz de restabelecer homeostaticamente a capacidade de aprender coisas novas, apagando mem?rias durante a noite. Tal fen?meno seria t?pico do sono de ondas lentas ( slow wave sleep , SWS) e caracterizado por mecanismos n?o-Hebbianos, isto ?, independentes da atividade neuronal sincr?nica. Outra abordagem postula que o sono desencadeia tamb?m um realce de conex?es sin?pticas espec?ficas, levando a um entalhamento de certos tra?os mnem?nicos no ?mbito de uma matriz de pesos sin?pticos redimensionados a cada noite. Tal entalhamento ? entendido como a combina??o de mecanismos Hebbianos e n?o-Hebbianos, capazes respectivamente de aumentar e diminuir os pesos sin?pticos em circuitos complementares, levando ? melhoria seletiva de mem?rias e a uma reestrutura??o da configura??o sin?ptica ( synaptic configuration , SC) que pode ser crucial para a gera??o de novos comportamentos ( insights ). Os achados emp?ricos indicam que a indu??o de plasticidade Hebbiana durante o sono acontece na transi??o do SWS para o est?gio de movimento r?pido dos olhos ( rapid eye movement , REM), possivelmente devido ?s grandes diferen?as entre os regimes das taxas de disparos entre os estados e ? regula??o positiva de fatores envolvidos na plasticidade sin?ptica de longo prazo. Neste estudo, as teorias da homeostase e do entalhamento foram comparadas usando uma rede neural artificial ( artificial neural network , ANN) alimentada com potenciais de a??o registrados no hipocampo de ratos durante todo o ciclo sono-vig?lia. Na simula??o em que a ANN n?o aplicou mecanismos de plasticidade de longo prazo durante o sono (transi??o SWS-REM), a distribui??o pesos sin?pticos foram inexoravelmente re-escalada para uma media proporcional ? taxa de disparo das entradas, apagando eventualmente o padr?o de pesos sin?pticos inicialmente estabelecido. Em contraste, quando a plasticidade de longo prazo foi modelada durante a transi??o SWS-REM, o aumento dos pesos sin?pticos foi observado em toda a gama de valores iniciais, efetivamente redistribuindo os pesos de modo a refor?ar um subconjunto de sinapses ao longo do tempo. Os resultados sugerem que uma regula??o positiva proveniente da plasticidade de longo prazo pode alterar completamente o papel do sono: sua aus?ncia leva ao esquecimento, sua presen?a leva a uma mudan?a mnem?nica positiva

Neste trabalho, diferentes tipos de microestruturas foram geradas por torneamento com ferramenta de diamante de ponta única e microendentação para serem replicadas através da prensagem a quente. Testes foram realizados para ser avaliada a geração destas microestruturas por dois métodos distintos: microdeformação e microusinagem, planejados para observar a replicação gerada por marca de endentação Vickers (piramidal) e, remoção de material (torneamento com ferramenta de diamante de ponta única). Uma revisão no processo de manufatura aplicada para a replicação de microestruturas é apresentada. Os materiais usados como molde e réplica foram o cobre eletrolítico e o polimetilmetacrilato (PMMA), respectivamente. Inicialmente, a usinabilidade do cobre eletrolítico foi avaliada sob diferentes condições de corte, a fim de determinar parâmetros apropriados de torneamento para obter um fino revestimento de superfície final (rugosidade). Observou-se que para avanços (f) de 10 mícrons por revolução e profundidade de corte (ap) de 5 mícrons, a superfície apresentou um baixo valor de rugosidade, isto é, 2,81 nm para rugosidade média (Ra) e 13,4 nm para rugosidade teórica (Rt). Além disso, observou-se que a microestrutura do material mostrou-se de fundamental papel na rugosidade, por conta da recuperação elástica dos grãos devido a anisotropia da estrutura policristalina do cobre. As microestruturas geradas para a replicagem foram: a) lente esférica, b) perfil senoidal e sulcos concêntricos. Os resultados mostraram que é viável a reprodução, com boa conformidade das microestruturas, por meio de prensagem a quente. Observou-se que as bordas e as superfícies finas com rugosidade em torno de 10 nm rms foram bem replicadas. / In this work, different types of microstructures were generated by single point diamond turning and microindentation for will replicated through the hot embossing. Tests were carried to evaluate the generation these microstructures by two distinct methods: micro-deformation and micro-machining, planned to observe the replication of the mark generated by the Vickers indenter (Pyramidal) and the latter by material removal (single point diamond turning). A review on several manufacturing processes applied to replication of microfeatures, is presented. The materials used as mould and replication workpiece were electroless copper and polymethylmethacrylate (PMMA), respectively. Initially, the machinability of electroless copper was evaluated under different cutting conditions to determinate appropriate turning parameters to obtain very fine surface finish (roughness). It was observed that for f = 10 microns of revolution (feed rate) and ap = 5 microns (depth of cut), the surface presented the roughness’ lowest value, i.e., 2,81 nm to medium roughness (Ra) and 13,4 nm to theoretical roughness (Rt). Moreover, it was observed that the microstructure of the material plays a fundamental role on roughness, because of the elastic recovery of grains due to the anisotropy of the polycrystalline structure of copper. The microfeatures generated were the following: a) spherical lens, b) sinusoidal profile and concentrical grooves. The results showed that it is feasible to reproduce, with good agreement, the microfeatures by means of hot embossing. It was observed that thin edges and fine surfaces with roughness around 10 nm rms were well replicated.

Le procédé d’estampage à chaud est considéré comme l'un des procédés les plus prometteurs de micro-Réplication pour l'élaboration des micro-Composants ou nano-Composants avec des matériaux polymériques dans différents domaines d'application . La mémoire consiste à caractériser les propriétés physiques des polymères thermoplastiques amorphes (PS, PMMA et PC) sur une large plage de température, ainsi que la modélisation physique, la simulation numérique et vérification expérimentale du procédé d’estampage à chaud.[...]Les propriétés visco élastiques des polymères retenus ont été caractérisées avec les essais décompression dynamiques. Le module de conservation, le module de perte et le facteur d'amortissement de polymère PMMA à partir de la température ambiante jusqu'à légèrement au-Dessus de Tg ont été obtenues. Le comportement visco élastique des polymères a été décrit par un modèle de Maxwell Généralisé et un bon accord a été observé. La simulation numérique des étapes du remplissage de procédé d’estampage à chaud a été réalisée enprenant compte des propriétés visco élastiques de polymère. Les effets de la température et dela pression de compression sur l'exactitude de réplication dans le procédé d’estampage à chaud ont été étudiés.[...]Un nouveau moule de compression complet, y compris le système de chauffage, le système de refroidissement et le système de vide a été développé dans notre groupe de recherche. Les dispositifs micro fluidiques avec la dimension de la cavité : environ 200 μm, 100 μm et 50 μmen PS, PMMA et PC plaque (épaisseur de 2 mm) ont été élaborés par le procédé d’estampage à chaud. Les effets des paramètres du procédé, tels que l’entrefer imposé, la température décompression, la matière compressée et la dimension de micro cavité, sur l’exactitude de réplication du procédé d’estampage à chaud ont été étudiés. / Hot embossing process is considered as one of the most promising micro replication processes for the elaboration of micro or nano components with polymeric materials invarious application fields. The thesis consists to characterize the physical properties of widelyused amorphous thermoplastic polymers (PS, PMMA and PC) over a large temperature range,along with the physical modelling, numerical simulation and experimental verification of thehot embossing process.[...] The polymers’ viscoelastic properties have been characterized with the dynamical compression tests. The storage modulus, loss modulus and damping factor of PMMA polymerfrom ambient temperature to lightly above Tg have been obtained. The viscoelastic behaviourof polymer has been described by a proposed Generalized Maxwell model and a good agreement has been observed. The numerical simulation of filling stage of hot embossing process has been achieved by taking into account of polymer’s viscoelastic properties. Theeffect of compression temperature and pressure on the replication accuracy in hot embossing process has been investigated in the simulation.[...] A new complete micro compression mould tools, including heating system, cooling system and vacuum system have been developed in our research group. The microfluidic devices with the cavity dimension eq. to about 200 μm, 100 μm and 50 μm in PS, PMMA and PC plate(thickness eq. to 2 mm) have been elaborated by the hot embossing process. The effects of the processing parameters, such as the compressive gap imposed, compression temperature, embossed material and die cavity dimensions, on the replication accuracy of hot embossing process have been investigated.

In dieser Arbeit werden Ergebnisse der Untersuchungen zur Laserstrukturierung von Prägewerkezeugen sowie zur Abformung von Gitterstrukturen mit Gitterperioden von kleiner gleich 2 µm in verschiedene Folien und Werkstoffverbunde präsentiert und diskutiert. Die hierfür entwickelte Kombination von Laserprozessen wird erläutert. Des Weiteren sind die auf Basis der experimentellen Untersuchungen ermittelten Parameterräume aufgezeigt und in Bezug zu theoretischen Beschreibungsmodellen gesetzt. Limitationen und Potentiale der einzelnen Teilprozesse werden dargelegt. Unter Anwendung der beschriebenen Strukturierungs- und Prozessparameter ist die Erstellung funktional einsetzbarer Prägewerkzeuge möglich. Für die Strukturübertragung konnte die Abformbarkeit der in die Oberflächen der Prägewerkzeuge eingebrachten beugungsoptisch wirksamen Gitterstrukturen mit Gitterperioden von kleiner gleich 2 µm bei Kontaktzeiten im Millisekundenbereich nachgewiesen werden.

No description available.

The written portion of this thesis work is meant to address and further investigate the visual work created using mediums of print and found video. This artistic research has been interested in examining varying associations with truth, recollection, and evidence. This includes the recollection of public histories and news-media narratives as well as my own history and trauma. Through this work my aim was to create a deconstruction and revolt against how associations are formed, and how to understand imagery as information. This thesis first discusses my relationship to appropriated imagery, then connects and examines it through the addition of poetic elements and events from my own lived experience.

Les travaux menés dans le cadre de cette thèse sont focalisés sur les procédés deréplication permettant la transformation des mélanges en composants par les technologiesen séquentiel ou bien en continu, selon les applications visées. Les développementsconcernent la mise en place et l’hybridation de différents procédés de micro-réplication(estampage à chaud de polymère thermoplastique et par laminage circulaire entre deuxrouleaux). Ces deux procédés sont développés et optimisés pour l’élaboration decomposants micro-structurés ou de microcomposants possédant des propriétésfonctionnelles mécaniques ou thermo-physiques requises à partir de différents mélangeschargés en poudres métalliques ou en nanotubes de carbone. Des exemples de réalisationde composants structurés, à base d’un système micro-fluidique possédant plusieurs canauxde 200 microns par 200 microns et des réservoirs de diamètre de 2 mm, sont prises commeexemple tout au long de ces travaux de cette thèse. Différents travaux de caractérisationsont été entrepris pour optimiser les procédés de micro-réplication par estampage à chaud etpar laminage circulaire entre deux rouleaux. / The Ph.D subject concerns the study of two micro-replication processes by hotembossing and roll to roll processes for thermoplastic polymers and loaded polymers withpowders or carbon nanotubes. The micro-replication processes, realized in sequential orcontinuous ways, use some different elaborated loaded feedstocks in order to obtainstructural components or micro-component with high aspect ratio and mechanical orthermo-physical properties.A chain combining hot embossing and roll embossing and powder metallurgy have beendeveloped in our lab and investigated. The different micro mould die cavities have beenrealized with different micro-manufacturing process, elastomeric mould has been obtainedby casting process. Finally, a metallic structured die cavity has been obtained by combininghot embossing and debinding and sintering stages. The second topic is the comparison ofmetallic die cavity mould obtained by roll embossing or rolls embossing. Two demonstratorshave been developed during the preparation of this Ph.D period: first a metallic micro-fluidicsystem with micro-structuration with diameter of 1 mm for the reservoir and 200 microns by200 microns for the channel have been realized and characterized by different methods.Secondly, some functional micro-component has been obtained with carbon nanotube andsome specific properties in terms of mechanic and thermo-physical properties have beencharacterized.

In vitro, la formation de structures de type tubulaire avec des cellules endothéliales de veine ombilicale humaine (HUVEC) a été étudiée en combinant la fonctionnalisation de la chimie des matériaux et le développement de la géométrie tridimensionnelle. Le polycarbonate (PC) a été utilisé comme modèle pour le développement de l'échafaud. Le film de polysaccharide naturel, basé sur un dépôt alternatif couche par couche (LbL) d’acide hyaluronique (HA) et de chitosane (CHI), a d’abord été appliqué sur une surface PC et caractérisé en termes de croissance d’épaisseur microscopie à balayage lascar (CLSM). Cette première fonctionnalisation se traduit par un revêtement complet de la couche PC. Une biofonctionnalisation supplémentaire avec un peptide adhésif (RGD) et deux peptides angiogénétiques (SVV et QK) a été étudiée, immobilisant ces peptides sur le groupe carboxylique de HA précédemment déposé, en utilisant la chimie bien connue du carbodiimide. La version marquée de chaque peptide a été utilisée pour caractériser l’immobilisation et la pénétration des peptides dans les couches de polyélectrolytes, aboutissant à une greffe réussie avec une pénétration complète dans toute l’épaisseur du LbL. Des tests in vitro ont été effectués à l'aide de cellules HUVEC pour évaluer leur efficacité d'adhésion et leur activité métabolique sur la LbL avec et sans immobilisation de peptides, ce qui a permis d'améliorer l'activité préliminaire lorsque des combinaisons de peptides sont utilisées. Enfin, les micro-canaux PC (μCh) ont été développés et caractérisés pour la première fois, et les autres expériences ont été réalisées sur un micromètre de 25 μm de largeur, fonctionnalisé avec une architecture (HA / CHI) 12,5 (PC-LbL) avec des peptides RGD et QK -RGD + QK) ou avec des peptides RGD et SVV (PC-RGD + SVV). Notre première expérience de tubulogénèse a montré de manière surprenante la formation de structures de type tubulaire déjà après 2h d'incubation en utilisant la combinaison double-peptides, mais uniquement avec PC-RGD + QK. Les tubes étaient également présents après 3 et 4 heures de culture. L'expérience de co-culture avec des péricytes humains dérivés du placenta (hPC-PL) montre comment la stabilisation des tubes a été améliorée après 3 et 4 heures également pour l'échantillon de PC-RGD + SVV. Globalement, notre matériel bio-fonctionnel avec les peptides PC-RGD + QK et PC-RGD + SVV permet la formation d'une structure de type tubulaire à la fois dans une expérience de monoculture et de co-culture. / In vitro, tubular-like structures formation with human umbilical vein endothelial cells (HUVECs) was investigated by combining material chemistry functionalization and three-dimensional geometry development. Polycarbonate (PC) was used as a template for the development of the scaffold. Natural polysaccharide’s film based on alternate layer-by-layer (LbL) deposition of hyaluronic acid (HA) and chitosan (CHI), was first applied to PC surface and characterized in terms of thickness growth both, in dry conditions using ellipsometry, and confocal lascar scanning microscopy (CLSM). This first functionalization results in a complete coating of the PC layer. Further biofunctionalization with one adhesive peptide (RGD) and two angiogenetic peptides (SVV and QK) was investigated, immobilizing those peptides on the carboxylic group of HA previously deposited, using the well-known carbodiimide chemistry. The labeled version of each peptide was used to characterize the peptides’ immobilization and penetration into the polyelectrolytes layers, resulting in a successful grafting with complete penetration through the entire thickness of the LbL. In vitro tests were performed using HUVECs to assess their adhesion efficiency and their metabolic activity on the LbL with and without peptide immobilization, resulting in a preliminary improved activity when peptide-combinations is used. Finally, PC micro-channels (μCh) were first developed and characterized, and the rest of the experiments were performed on μCh of 25μm width, functionalized with (HA/CHI)12.5 architecture (PC-LbL) with RGD and QK peptides (PC-RGD+QK) or with RGD and SVV peptides (PC-RGD+SVV). Our first tubulogenesis experiment surprisingly showed the formation of tubular-like structures already after 2h of incubation using the double-peptides combination but only using PC-RGD+QK the tubes were present also after 3 and 4 hours of culture. The co-culture experiment with human pericytes derived from placenta (hPC-PL) demonstrates how the stabilization of the tubes was improved after 3 and 4 hours also for the PC-RGD+SVV sample. Globally our bio-functional material with PC-RGD+QK and PC-RGD+SVV peptides allow the formation of tubular-like structure in both mono and co-culture experiment.