Montmorillonite reinforced polymers are a new development in the area of nanocomposite materials. Since reinforcement of epoxy is important to the development of high strength adhesives and composite matrices, the introduction of montmorillonite to epoxy is of interest. Compositional effects on epoxy reactivity, on molecular relaxation, and on mechanical properties were investigated. Change in reactivity was determined by Differential Scanning Calorimetry. Tensile properties at room temperature indicated improved modulus and retention of strength of the epoxy matrix but a decreased elongation to failure. Depression of dry nanocomposite glass transition was observed for nanocomposites beyond 5% by weight montmorillonite. Samples that were saturated with water showed lower moduli due to the epoxy matrix. The greatest moisture absorption rate was found at 7%, the least at 3%.

L’incorporation de nanotubes de carbone dans une matrice polymère permet d’obtenir des matériaux nanocomposites avec des propriétés exceptionnelles. Toutefois, ces dernières dépendent de l’état de dispersion et distribution des nanotubes dans la matrice. Afin de conférer de meilleures propriétés, il est essentiel que le procédé de synthèse des nanocomposites permette une répartition contrôlée des nanotubes dans la matrice. Un procédé de polymérisation in situ, en présence de nanotubes de carbone, a été choisi. Ce dernier permet de contrôler la répartition des nanotubes dans la matrice grâce à l’utilisation des ultrasons. Afin d’optimiser ce procédé, et notamment lors de la polymérisation anionique activée de l’e-caprolactame, l’influence de la présence des nanotubes sur la vitesse de polymérisation et les propriétés rhéologiques du milieu polymérisant a été déterminée. Grâce à une étude calorimétrique suivie d’une étude rhéocinétique, il a été démontré que la présence de nanotubes ralentit la polymérisation et augmente fortement la viscosité du milieu. Cette inhibition provient probablement d’une réaction entre les nanotubes et le catalyseur utilisé pour la polymérisation et dépend donc de l’état de dispersion des nanotubes dans la matrice, lequel peut ainsi être estimé par les études cinétiques. L’étude des propriétés rhéologiques et électriques des nanocomposites à matrice polystyrène et à renforts de nanotubes de carbone a également été entreprise. Suivant l’état de dispersion ainsi que les différents paramètres opératoires, les seuils de percolation électrique et rhéologique ont ainsi pu être déterminés / The introduction of carbon nanotubes into polymers leads to nanocomposite materials with exceptional properties. These later depend, however, on the dispersion and distribution of carbon nanotubes inside the matrix. A key objective, in nanocomposite preparation, is the set up of incorporation processes allowing a good state of dispersion of the nanotubes into the matrix. An in situ polymerization process, coupled with an ultrasound processor, was chosen to best fulfill this objective. The optimization of this process implies the knowledge of the evolution of reaction kinetics and rheological properties during the polymerization. The influence of carbon nanotubes on the anionic activated polymerization of e-caprolactam was investigated by calorimetric and rheokinetic studies. Carbon nanotubes were found to slow down polymerization kinetics and highly increase the viscosity after a certain conversion degree. This inhibition phenomenon could be produced by a reaction between carbon nanotubes and the catalyst employed for the polymerization reaction. The inhibition effect depended also on the state of dispersion of the nanotubes, consequently, kinetic and rheokinetic measurements are an indirect method to estimate the state of dispersion. The electrical and rheological properties of the nanocomposites were also investigated. The influence of the state of dispersion and other parameters, such as temperature, on the electrical and rheological percolation thresholds was identified

L’objectif de cette étude est l’élaboration de nanocomposite à base d’un élastomère de styrène et de butadiène (SBR) par l’ajout d’une dispersion aqueuse (slurry) de nanocharges lamellaires de phosphate de zirconium en phase α (α-ZrP ou ZrP). Les travaux s’attardent d’abord sur le mélange entre le SBR à l’état fondu et le slurry de ZrP en absence de traitement de surface. Différents stratégies d’élaboration sont ensuite envisagées afin d’améliorer la dispersion (intercalation exfoliation) des feuillets de ZrP dans le matériau en couplant le traitement de surface du ZrP et les paramètres de mise en œuvre. Différents traitements de surface sont abordés avec l’utilisation d’un agent intercalant métallique (Na+), de deux intercalants alkylamines (propylamine, octadécylamine) et d’un agent d’exfoliation (hydroxyde de tétrabutylammonium). En parallèle, plusieurs procédés de mise en œuvre générant des écoulements complexes sont utilisés. La complémentarité entre la diffraction des rayons X (DRX), la microscopie électronique en transmission (MET) et la spectroscopie mécanique (DTMA) permet d’obtenir une analyse multi-échelle de l’état de dispersion du ZrP et de proposer des scénarii décrivant les mécanismes de dispersion en fonction des paramètres étudiés. Un effort important est apporté pour la compréhension de la relation structure à l’échelle nanoscopique et les propriétés macroscopiques du matériau. Une étude comparative est ensuite proposée entre les valeurs expérimentales de l’effet de renforcement des matériaux et les prédictions des modèles Krieger-Dougherty et Halpi-Tsai / This work focuses on the melt processing of nanocomposite materials obtained from a synthetic lamellar filler, α-zirconium phosphate (α-ZrP), dispersed within a synthetic rubber of the SBR type. The first step is the melt compounding using aqueous slurry of α-ZrP without any treatment. Following, several kinds of surface modifiers such as sodium cation, alkylamines and tetrabutylammonium hydroxide and different melt processing conditions are investigated to improve the level of dispersion of ZrP platelets into the matrix. X-ray diffraction, transmission electron microscopy and dynamical mechanical method are used as a multi-scale analysis to quantify the state of dispersion of the filler within the nanocomposite. Several mechanisms of dispersion are described depend on the surface modifying treatment and the melt processing parameters and the structure-properties relationship are studied. A comparison between the material reinforcement and two models of predictions, Krieger-Dougherty and Halpin-Tsai are discussed

O óxido de grafeno (OG), nanomaterial sintetizado a partir do grafite, tem atraído atenção como adsorvente com grande capacidade de remoção de cátions e diversos contaminantes de soluções aquosas, devido a presença dos grupos hidroxila, epóxi, carbonila e carboxila em sua superfície. Este trabalho, visa avaliar o potencial do óxido de grafeno bruto (OG) e de sua forma imobilizada em poli(divinilbenzeno) (PDVB-OG) na remoção de íons de césio de uma solução aquosa sintética. Os experimentos foram realizados em batelada, e foi avaliado a influência do tempo de contato e da concentração inicial de íons de césio. Para descrever a isotermas de equilíbrio foram aplicados os modelos de Langmuir e Freundlich, e a cinética do processo de adsorção, foi avaliada utilizando-se os modelos de pseudo-primeira ordem, pseudo-segunda ordem e difusão intrapartícula. Para prever a espontaneidade do processo de adsorção, foi calculado a energia livre de Gibbs. Nos experimentos de adsorção de íons de césio, o OG e o nanocompósito PDVB-OG, após 30 min. de contato, apresentaram taxa de remoção de 80% e 63% respectivamente. O modelo que melhor descreveu o processo de adsorção, para ambos adsorventes, na faixa de concentração de 30 a 130 mg.L-1, foi o de Langmuir e a capacidade máxima de adsorção calculada foi de 17 mg.g-1 para o OG e de 15 mg.g-1 para o PDVB-OG. Tanto para o OG quanto para o PDVB-OG, o modelo cinético que melhor descreveu o processo foi o de pseudo-segunda ordem e o valor da energia livre de Gibbs determinou que a adsorção dos íons de césio foi espontânea. A matriz polimérica não apresentou capacidade de remoção significativa, evidenciando que a adsorção dos íons césio pelo nanocompósito de PDVB-OG se deve a presença do OG imobilizado. Por outro lado, devido a maior densidade, o PDVB-OG foi facilmente separado da solução por decantação após o experimento de adsorção. Os resultados indicam a capacidade do OG e do nanocompósito PDVB-OG em tratar rejeitos líquidos radioativos, a fim de minimiza-los. / Due to the presence of hydroxyl, epoxy, carbonyl and carboxyl groups on its surface, graphene oxide (GO), synthesized from graphite, has attracted attention as a high adsorbent of cation removal and several contaminants from aqueous solutions. This work aims to evaluate the potential of graphene oxide (GO) and its immobilized form as poly(divinylbenzene) (PDVB-GO) in the removal of cesium ions from a synthetic aqueous solution. The experiments were performed in batch, and the influence of the contact time and the initial concentration of cesium ions were studied. Langmuir and Freundlich models as the equilibrium isotherms, and the kinetics of the adsorption process, pseudo-first order, pseudo-second order and intraparticle diffusion models, were evaluated GO and PDVB-GO, removed after 30 min. of contact time 80% and 63% of cesium ion, respectively for both adsorbents. The maximum adsorption capacities were 17 mg.g-1 for the GO and 15 mg.g-1 for the PDVB-GO. For both GO and PDVB-GO, Langmuir model fitted better in the adsorption process, the Gibbs Free Energy showed that this process for were spontaneous and the kinetic models were the pseudo-second order. As the polymer matrix, PDVB, has no significant removal capacity, the adsorption of the cesium ions by the PDVB-GO nanocomposite is due to the presence of the GO. On the other hand, the PDVB-GO was easily separated from the solution by decantation after the adsorption experiment. The results indicate the ability of the GO and the PDVB-GO nanocomposite to treat radioactive liquid wastes in order to minimize them.

Neste trabalho de mestrado foram desenvolvidos nanobiocompósitos contendo quitosana (QS) e nanopartículas de prata (AgNPs) para aplicação em matrizes poliméricas com propriedades bactericidas. O trabalho foi conduzido em 4 etapas, sendo: i) a primeira referente ao estudo e escolha do melhor modo de estabilização dos colóides de prata em solução, sendo escolhido o modo de estabilização estérica com a quitosana (QS); ii) a segunda parte está relacionada com um estudo detalhado da interação entre a QS e as nanopartículas de prata (AgNPs) além da otimização da relação QS:AgNPs no nanocompósito para se obter maior ação bactericida; iii) foi também proposta uma rota de síntese na qual não se utiliza-se o Boro Hidreto de Sódio (NaBH4) como redutor, composto altamente reativo, sendo utilizados o citrato de sódio e QS conjuntamente como redutores; iv) inserção do nanocompósito QS:AgNPs em uma matriz de polivinil álcool (PVA). Foram utilizadas as técnicas de espectroscopia UV-vis e FT IR, DLS, Potencial Zeta, MET, DR-X, ensaios microbiológicos de MIC, OD595 e teste de halo de inibição, TGA, DSC e ensaios mecânicos. Concluímos que o uso da QS como agente estabilizante em comparação ao PVA é a mais indicada, devido ao maior número de grupos funcionais interagindo com as nanopartículas de prata. O poder de ação bactericida do nanocompósito QS:AgNPs pode ser aumentado numa certa relação entre ambos, a saber 4:1 em massa. A síntese utilizando citrato de sódio e QS como redutores mostrou a possibilidade da obtenção de nanopartículas de prata pequenas, com tamanho de 2 - 5 nm com estrutura esférica ou maiores. com tamanho de 300 nm, apresentando estruturas dendríticas, dependendo apenas do tempo de reação e concentração de citrato de sódio. A última etapa revelou a possibilidade da inserção do nanocompósito no polímero PVA sem perda significativa das características térmicas e mecânicas do polímero. / The work reported here was aimed at developing chitosan/AgNPs based nanobiocomposits for bactericidal applications. The studies were divided into four main steps, viz.,: i) optimization of the silver colloids stabilition process, in which the use of chitosan resulted in the best stability, ii) a detailed investigation on the interactions between chitosan and AgNPs, as well as the optimization of the chitosan :AgNPs ratio to promote the best bactericidal effect, iii) development of a new synthetic route without using NaBH4, in a search for an environmentally-friendly route, and iv) incorporation of the chitosan:AgNps nanobiocomposites in a PVA matrix for application as smart food packaging. The nanobiocomposites were characterizaed via UV-vis and FT IR spectroscopies, DLS, Zeta potential, TEM and DR-X. Biological essays had also been carried out, as well as tensilestress and thermo analyses (DSC and TGA). The best bactericidal effect was observed for a nanobiocompostie comprising chitosan:AgNPs at a ratio of 4:1 (wt/wt). The synthetic route employing sodium citrate as reducing agent resulted in AgNPs with average diameters of 2 5 nm, as well as bigger nanoparticles with diameters of ca. 300 nm, depending on the reaction time and citrate concentration. The incorporation of the chitosan:AgNPs composites in the PVA matrix resulted in the formation of a bactericidal composite with good mechanical and thermal properties, suitable for applications as smart food packing.

O entendimento dos mecanismos de degradação que agem sob os nanocompósitos poliméricos frente ao intemperismo (luz UV, calor, oxigênio, chuva ácida, entre outros), é o ponto chave para o desenvolvimento de novos aditivos e novas aplicações. Para este trabalho a síntese do nanocompósito foi realizada no estado fundido, utilizando-se uma extrusora de dupla rosca. A matriz polimérica utilizada foi o HMS-PP (polipropileno com alta resistência do fundido) sintetizado por irradiação gama e a argila Montmorilonita. Para melhor compatibilização entre a matriz e a nanocarga, foi utilizada o agente compatibilizante andrido maléico. Para os ensaios de envelhecimento ambiental e acelerado em estufa, os corpos de prova foram confeccionados por meio de termoprensagem. A caracterização dos efeitos da adição de argila e do envelhecimento nos nanocompósitos, presupôs o emprego das técnicas de ensaios mecânicos, Calorimetria Diferencial Exploratória (DSC), Termogravimetria (TGA), Espectroscopia no Infravermelho por Transformada de Fourier (FT-IR), Espectrometria de Fluorescêcia de Raios X por Dispersão de Comprimento de Onda (WDXRF), Microscopia Eletrônica de Varredura (MEV), Índice de Fluidez (IF), Difração de Raios-X (DRX) e Espectroscopia de Energia Dispersiva (EDS). Foram ensaiadas amostras com 0,1; 1; 3; 5 e 10% de argila. A amostra com porcentagem de 5% de argila demonstrou uma melhor estabilidade frente ao ensaio de envelhecimento ambiental e no envelhecimento acelerado em estufa. Por outro lado na amostra com maior porcentagem de argila (10%) ocorreu o inverso, sob ensaio ambiental houve maior degradação e sob envelhecimento acelerado em estufa, manteve-se resistente até 56 dias de envelhecimento. Nas porcentagens estudas (menor que ≤ 3%) de argila, pode-se constatar um equilíbrio entre o efeito barreira da argila e a ação dos íons metálicos que aceleram o processo degradativo. / The understanding of degradation mechanism action on the polymer nanocomposites in face of weathering (UV light, heat, acid rain, among others), is the key for development of new additives and new applications. In this work the nanocomposite synthesis was carried in molten state, using twin-screw extruder. The polymer matrix was the HMS-PP (high melt polypropylene) synthesized by gamma irradiation and the nanometric inorganic component was the montmorillonite clay. For better compatibilization between the matrix and clay, it were used maleic anhydride as coupling agent. For environment and in oven accelerated aging assays, the dumbbell samples were prepared under hot pressing. The characterization of clay addition effects and aging effects on the nanocomposites, required the use of techiniques of Differential Scanning Calorimetry (DSC), Thermogravimetry (TGA), Fourier Transformed Infrared Spectroscopy (FT-IR), Xray Fluorescence (WDXRF), Scanning Eletron Microscopy (SEM), Energy Dispersive Spetroscopy (EDS) and mechanical properties. Samples with 0.1; 1; 3; 5; 10 % of clay were tested. The sample with 5% of clay showed better stability on the environmental assay and accelerated aging in oven assay. On the other hand, the sample with higher percent of clay (10%), was more degraded under on environmental aging than under accelerated aging in stove. In this case, became more resistant until 56 days of assay. On the studied concentrations (less than ≤ 3%) of clay, it can be seen an equilibrium between barrier effect and metallic ions action accelerating the degradative process.

A produção de elementos filtrantes para água a partir de polímeros é bastante difundida no mercado, mas possui uma característica indesejada: nem sempre são eficientes e capazes de reter ou eliminar microorganismos presentes. O presente trabalho propõe-se a produzir filtros com propriedade biocida compostos por nanocompósitos de polietileno de ultra alta massa molar (PEUAMM), modificados com surfactante não iônico e nanopartículas de prata, sendo os polímeros responsáveis pela estrutura porosa uniforme dos filtros e as nanopartículas de prata incorporadas nos elementos filtrantes pela ação biocida. Os polímeros particulados foram classificados por peneiramento e apresentaram duas curvas granulométricas distintas de 150 a 200?m e de 300 a 400?m, sendo posteriormente utilizados para a sinterização dos elementos filtrantes. As nanopartículas de prata foram incorporadas aos elementos filtrantes, obtendo-se corpos de prova que foram caracterizados através do uso das técnicas de difratometria de raios-X, microscopia eletrônica de varredura, microanálise por espectroscopia de raios-X por dispersão de energia. Foram também realizadas avaliações dos elementos filtrantes através de ensaios de ação biocida, vazão e taxa de filtração e presença de extraíveis. Os resultados obtidos indicaram a formação do nanocompósito e diferentes propriedades foram observadas para os elementos filtrantes em função da porosidade alcançada. / The production of polymer based filter elements for water is widespread in the market but has an undesirable characteristic: they are not always efficient and capable of retaining or eliminating microorganisms. This paper proposes the production of filters with biocidal activity, composed by nanocomposites of ultra high molar mass polyethylene (UHMMPE), modified by non-ionic surfactant and silver nanoparticles. The polymers are responsible for the uniform porous structure of the filters and the silver nanoparticles for its biocidal action. The particulate polymers were classified by sieving and presented two distinct grain size ranges, one of 150 to 200?m and the other of 300 to 400?m. Samples were collected from the prepared filter elements and characterized by X-ray diffractometry, scanning electron microscopy and microanalysis. Evaluation of the filter elements were also carried out and their biocidal activity was tested, as well as the flow and filtration rates and the presence of extractables were determined. The results indicate the formation of the nanocomposite and different properties were observed for the filter elements according to its porosity.

Neste presente trabalho foi realizado um estudo sobre copolímeros em bloco e seus nanocompósitos com diferentes estruturas morfológicas. Os polímeros estudados foram copolímeros de poliestireno-b-poli(etileno-co-butileno)-b-poliestireno (SEBS), sendo dois desses copolímeros com fração em massa de 30% de blocos de poliestireno (PS), e um deles modificado com anidrido maleico na fase de poli(etileno-co-butileno) (PEB). Os outros três copolímeros têm 13% de blocos de PS. A nanopartícula utilizada foi a argila montmorilonita organofílica Cloisite 20A. Os nanocompósitos foram preparados por dois métodos: i) mistura no estado fundido (extrusão); ii) solução. As microestruturas dos materiais resultantes foram caracterizadas pelas técnicas de espalhamento de raios X a baixo ângulo (SAXS) e difração de raios-X (DRX). As propriedades reológicas foram avaliadas em dois tipo de fluxo (cisalhamento e elongacional). Para avaliar as propriedades reológicas em fluxo de cisalhamento foram realizados ensaios de cisalhamento oscilatório em pequenas amplitudes (SAOS), cisalhamento oscilatório em grandes amplitudes (LAOS) e varredura de tempo (TS). Para avaliar as propriedades reológicas em fluxo elongacional foram realizados ensaios com geometria apropriada (SER), acoplada ao reômetro rotacional. Estes ensaios foram conduzindo em duas direções: paralela (longitudinal) e perpendicular (transversal) à direção do fluxo de extrusão. As análises de caracterização estrutural (DRX e SAXS) indicaram uma estrutura intercalada para os nanocompósitos SEBS/20A e esfoliada para as matrizes modificadas com anidrido maleico. A caracterização reológica dos copolímeros com 30% de blocos de PS em fluxo de cisalhamento mostrou que as morfologias dos nanocompósitos são estáveis com o tempo de cisalhamento, e permitiu confirmar as estruturas dos nanocompósitos. Para os copolímeros com 13% de blocos de PS foi possível identificar as temperaturas de transição ordem-ordem e ordem-desordem. Os resultados dos ensaios reológicos indicaram que ocorre alinhamento dos cilindros na direção dos fluxos de cisalhamento e elongacional. Também foram avaliadas as propriedades mecânicas, e os resultados mostraram que o comportamento mecânico é altamente influenciado pela estrutura morfológica e a incorporação de argila. / In this work block copolymers and their nanocomposites were studied. The polymers studied were copolymers of polystyrene-b-poly(ethylene-co-butylene)-b-polystyrene (SEBS), with two samples containing 30 wt% of PS blocks. The other three copolymers contained 13% of PS blocks. Two block copolymers are modified with maleic anhydride. The reinforcement used was the montmorillonite organoclay Cloisite 20A. The nanocomposites were prepared by two methods: i) melt blending (extrusion), with which a cylindrical hexagonal structure (anisotropic and isotropic) was obtained; ii) casting, with which a lamellar structure was obtained. The microstructures were characterized by the techniques of small angle X-ray scattering (SAXS) and X-ray diffraction (XRD). The rheological properties were evaluated in two different flows (shear and elongational). To evaluate the rheological properties in shear flow the samples were tested under small amplitude oscillatory shear (SAOS), large amplitude oscillatory shear (LAOS) and time sweep (TS). To evaluate the rheological properties in elongational flow, tests were carried out using an appropriate geometry (SER). The latter tests were conducted on samples aligned in two different directions: parallel (longitudinal) and perpendicular (transverse) to the flow direction of extrusion. The structural characterization analysis (XRD and SAXS) indicated an intercalated nanocomposite structure for SEBS/20A, and an exfoliated structure for the copolymers modified with maleic anhydride. The rheological characterization of the samples in shear flow showed that the morphologies of the nanocomposites are stable with time of shearing, and it confirmed the morphologies of the nanocomposites (30% PS block). For copolymers with 13 % of PS blocks it was possible to identify the order-order and order-disorder transition temperatures. The rheological tests showed that it is possible to align the morphologies in shear and elongational flows. The mechanical properties were also evaluated; the results have shown that the mechanical behavior was strongly influenced by the morphological structure and clay incorporation.

Neste trabalho, pós magnéticos nanoestruturados de PrxFe94-xB6 (x = 6, 8, 10 e 12) foram preparados a partir da combinação do processo de hidrogenação, desproporção, dessorção e recombinação (HDDR) e moagem de alta energia entre uma liga em estado bruto de fusão (Pr14Fe80B6) e Fe-α em pó. As nanopartículas produzidas apresentaram propriedades magnéticas e microestruturais comparáveis aos estudos realizados em hipertermia. O tempo ideal para obtenção de nanopartículas magnéticas é de 5 horas (a 900 rpm). Foi constatado que quanto maior o tempo de moagem, maior o percentual de carbono nas partículas (0,05 - 3,43 % C). O carbono é proveniente do ácido oléico adicionado como surfactante na etapa de moagem. Os nanocompósitos obtidos exibiram forças coercivas entre 80 Oe (6,5 kAm-1) e 170 Oe (13,5 kAm-1), e momentos magnéticos variando entre 81 - 129 Am2kg-1. A partir da difração de raios X foram identificadas apenas duas fases em todas as amostras: Fe-α e a fase magnética Pr2Fe14B. Nanopartículas isoladas com diâmetro aproximado de 20nm foram analisadas. Todas as composições estudadas apresentaram aquecimento proveniente da exposição a um campo magnético alternado (f = 222 kHz e Hmax ~3,7 kAm-1) comparáveis aos reportados na literatura. As variações de temperaturas (ΔT) dos pós foram: 51 K referente à composição de Pr6Fe88B6, 41 K para Pr8Fe86B6, 38 K no composto com 10% at. Pr (Pr10Fe84B6) e 34 K em Pr12Fe82B6. As taxas de absorção específicas estimadas foram de 201 Wkg-1 para a composição Pr6Fe88B6, 158 Wkg-1 para a composição Pr8Fe86B6 e 114 Wkg-1 para as composições Pr10Fe84B6 e Pr12Fe82B6. / In this work, PrxFe94-xB6 (x = 6, 8, 10 and 12) nanostructured powders were prepared by a combination of hydrogenation, disproportionation, desorption and recombination (HDDR) process with high energy milling applied to the mixture of an as-cast alloy (Pr14Fe80B6) and α-Fe. The produced nanoparticles showed magnetic properties comparable to those reported in hyperthermia studies. The optimal time to obtain the magnetic nanoparticles is 5 hours (at 900 rpm). It was verified that longer milling times cause an increase in carbon percentage on the particles. The carbon is derived from oleic acid added as a surfactant in the milling step. The nanocomposites exhibit coercive force ranging from 80 Oe (6.5 kAm-1) to 170 Oe (13.5 kAm-1) and magnetic moments in the range of 81 129 Am2kg-1. From the x-ray diffraction analyses, only two phases were found in all samples: α-Fe and the magnetic phase Pr2Fe14B. Individual nanoparticles with diameter of about 20 nm were verified. The samples studied presented heating when exposed to an alternating magnetic field (f = 222 kHz e Hmax ~3.7 kAm-1) comparable to reported in literature. Temperature variations (ΔT) of the powders were: 51 K for Pr6Fe88B6, 41 K for Pr8Fe86B6, 38 K for Pr10Fe84B6 and T = 34 K for Pr12Fe82B6. The specific absorption rates (SARs) of the powders were 201 Wkg-1 for Pr6Fe88B6 composition, 158 Wkg-1 on the composition Pr8Fe86B6, and 114 Wkg-1 for Pr10Fe84B6 and Pr12Fe82B6 compositions.

Spent oil based drilling fluid and cutting wastes are global liabilities due to their hazardous hydrocarbon content which impacts negatively on flora, fauna, and global carbon footprint. The formulation of two demulsifiers to ensure chemically enhanced phase separation of this waste into oil, water and solid components was successfully carried out in addition to recycling the solid phase into PA6 nanocomposite materials. Initial characterisation of the untreated waste was carried out by Fourier Transform Infra Red (FTIR) for total petroleum hydrocarbon (TPH) analysis, Inductively coupled plasma optical emission spectrometry (ICPOES) for quantitative elemental analysis and Energy dispersive xray analysis (EDXA) for qualitative elemental composition amongst other characterisation methods. The analysis showed that the sample had a high hydrocarbon load of 662,500mg/kg and a high heavy metal load for Pb of 122mg/kg. No As, Cd, Hg were detected. The demulsifier formulations were composed of isopropanol, sodium dodecyl sulphate, poloxamer, sodium chloride, chitosan in 0.2M acetic acid and deionised water for demulsifier S4 and addition of phosphoric acid for demulsifier S3. Hydrocarbon reduction on the extracted solid phase nanofiller S3 and nanofiller S4 was 98.6% and 98.5% respectively after demulsification. The demulsified spent oil based drilling fluid solid extracts were below OSPAR regulation of < 1% oil on cutting by weight. However, recycling of the recovered solid was carried out in order to achieve environmentally sustainable management of the waste in Polyamide 6 (PA6) nanocomposite manufacture/fabrication. The formulation of different blends of PA6 nanocomposite materials from untreated, demulsifier treated and thermally treated drilling fluid and cuttings was successfully achieved. Nanocomposite leaching test showed Pb immobilisation. The flexural and compressive - modulus and strength of the PA6 were markedly improved in the presence of the nanofillers and glass fibre. This was attributed to the reinforcement, exfoliating, stiffening, rigidity effect of the nanofillers. S6 (untreated drilling fluid) nanofillers significantly improved the mechanical properties of PA6. This was attributed to the increased interfacial bonding between the fillers and the polymer matrix as a result of the petroleum hydrocarbon present in the sample. The Thermogravemetric analysis (TGA) results showed that nanocomposites PA6/S3 and PA6/S3/GF30 had improved the thermal stability of PA6 by 13.6% and 38.8% respectively compared to PA6/S2 and PA6/S2/GF30 (simulated commercial nanocomposite materials) that improved PA6 by 9.7% and 35.8% respectively.