This project deals with the potential of membrane stratified solar ponds which consist of two water layers, where one is a salt solution here, and a separating translucent membrane. An experimental pond was set up to study the thermal behaviour of such collector systems. The input is mainly solar radiation, sometimes when the ambient temperatures are higher than the pond temperatures also heat from the environment is transferred into the pond. The measured temperatures of the pond, the ambient temperature, the global radiation and wind speed were the basis data for thermal calculations which showed that the pond was working well as a solar collector and thermal storage system all in one. Heat was not extracted from the pond however, only the losses to the environment were studied. It was found out that the pond temperatures were higher than the ambient temperature over the whole measurement period of 12 days, and insulation and pollution problems as well as future prospects and suggestions for further studies are discussed at the end of this paper.

Nowadays, lighting represents 20% of the global electricity consumption. Light can be produced using different technologies but more than 100 years after its invention, the incandescent bulb is still the most sold and one of the more used light sources. Of the total energy input in an incandescent bulb more than 90% is lost as heat while less than 10% is converted into visible light. However, there are alternative technologies which use up to 85% less energy for conventional lighting and there are even more efficient light sources for other purposes that if they replace completely all incandescent lamps over the world could reduce dramatically the global electricity consumption and greenhouse gases emissions. One may identify these alternative technologies mainly as LEDs and discharge lamps, but are they the unique alternatives? This thesis is focused on a new lighting technology whose name is LightLab and which is based on the field emission and cathodoluminescence concepts. This technology is under the research and development stage but prototypes have already achieved energy savings over 85% compared to incandescent lamps with a great color performance and with the advantage that it does not use mercury or other hazardous substances compared with discharge lamps. Thus, in the first part of the project all technologies and last improvements are studied while the second part analyses the market applications possibilities for the LightLab lamp considering the environmental perspective regulations and comparing the lamp with the other light sources. The result is that despite there are still some unknown parameters that need to be developed or improved, the lamp has a great potential for different applications fields.

<p>Oxygen-diluted Combustion (OdC) technology has evolved from the concept of Excess Enthalpy Combustion and is characterized by reactants of low oxygen concentration and high temperature. Recent advances in this technology have demonstrated significant energy savings, high and uniform thermal field, low pollution, and the possibility for downsizing the equipment for a range of furnace applications. Moreover, the technology has shown promise for wider applications in various processes and power industries.</p><p>The objectives of this thesis are to analyze the thermodynamic aspects of this novel combustion technology and to quantify the enhancement in efficiency and heat transfer inside a furnace in order to explore the potentials for reduced thermodynamic irreversibility of a combustion process and reduced energy consumption in an industrial furnace. Therefore, theoretical and experimental investigations were carried out.</p><p>The 2nd law of thermodynamics analyses of OdC systems have been carried out for cases in which the oxidizer is either oxygen (Flameless-oxy-fuel) or air (High Temperature Air Combustion, HiTAC). The analyses demonstrate the possibilities of reducing thermodynamic irreversibility of combustion by considering an oxygen-diluted combustion process that utilizes both gas- and/or heat-recirculation. Furthermore, the results showed that an oxygen-diluted combustion system that utilizes oxygen as an oxidizer, in place of air, results in higher 1st and 2nd law efficiencies.</p><p>Mathematical models for heat regenerators were developed to be designing tools for maximized heat recovery. These models were verified by heat performance experiments carried out on various heat regenerators.</p><p>Furthermore, experiments were performed in a semi-industrial test furnace. It was equipped with various regenerative burning systems to establish combustion and heat transfer conditions prevailing in an industrial furnace operating based on HiTAC. The tests were carried out at seven firing configurations, two conventional and five HiTAC configurations, for direct and indirect heating systems.</p><p>Measurements of energy balance were performed on the test furnace at various configurations in order to obtain the 1st law efficiency. Moreover, local measurements of temperature, gas composition, and heat fluxes in the semi-industrial test furnace were performed to find out the main characteristics of HiTAC flame and the effects of these characteristics on the heating potential, i.e., useful heating in the furnace. In the case of HiTAC, these measurements showed uniformities of chemistry, temperature, temperature fluctuation, and heat fluxes profiles. The values of fluctuations in temperature were small. The high speed jets of the fuel and air penetrated deep into the furnace. The fuel gradually disappeared while intermediate species gradually appeared in relatively high concentrations and at broader regions inside the furnace. These findings indicate: a large reaction zone, low specific combustion intensity in the flame, low specific fuel energy release, and high heat release from this large flame. In addition to the thermodynamic limitations to the maximum temperature of the Oxygen-diluted Combustion, the low specific energy release of the fuel and the high heat release from the flame to its surroundings cause this uniform and relatively moderate temperature profile in a HiTAC flame, consequently suppressing thermal-NO formation.</p><p>Heat flux and energy balance measurements showed that heating potential is significantly increased in the case of HiTAC compared to that in the conventional case, implying much more energy savings than the apparent heat recovery from the heat regenerators, and consequently much less pollutants emissions. Therefore, it is certain that this large HiTAC flame emits more thermal radiation to its surroundings than the conventional flame does, in spite of the moderate-uniform temperature profile of the flame. This intense heat flux was more uniform in all HiTAC configurations, including the indirect heating configuration, than that of the conventional-air combustion configuration.</p>

This thesis investigates the possibility of using an unglazed flat-plate solar collector as a cooling radiator. The solar collector will be connected to the condenser of a heat pump and used as cooler during nighttime. Daytime the solar collector will be connected to the evaporator of the heat pump and used as heat source. The two widely differing fields of application make special demands on the solar collector. The task is given by the heat pump manufacturer Thermia and the main objective is to find out whether a solar collector should be used as a cooler or not. The performance of the solar collector under varying environmental conditions is investigated using COMSOL Multiphysics 3.3. Only the cooling properties are investigated here. The performance of the solar collector as a heat exchanger is estimated using the effectiveness-NTU method, and the solar collector is found to be a good heat exchanger at low wind speeds. The heat transfer coefficients of the convection and radiation are determined for varying temperature and wind speeds. The convective heat transfer coefficient is lowered by tubes above the absorber plate and for a high convective heat transfer rate the solar collector surface should be smooth. For a high radiative heat transfer rate the surface needs to have a high emissivity. The cooling rate is higher from a warm surface than from a cold and since no temperature change of the heat carrier is necessary the solar collector should be kept at a high temperature. To increase the cooling rate alterations need to be made to the solar collector that makes its heating performance deteriorate. A solar collector that can be used for cooling is not an efficient solar collector.

<p>As a part of the fight against the global warming the energy production needs to be more efficient and redirected towards sustainable options. One alternative is cogeneration, which means that electricity and heat is produced in one plant. The purpose with this survey is to examine if there are any commercial available combined heat and power techniques, based on combustion of solid moist biomass, which are suitable to small-scale applications. The technique must be able to produce between 2 and 10 MW thermal and the heat demand is a Swedish district-heating system. When already published reports had been studied, the Organic Rankine Cycle (ORC) was chosen as the most suitable technique. The possibility of using the ORC to generate electricity from the district-heating return flow was considered simultaneously. The chosen ORC-technique was then evaluated in Excel. The first aspect to be examined was how the performance of a combined heat and power plant was affected by variations in the supply line temperature. It showed that the performance reaches top levels when the temperature is low. The second part contains an optimisation, in a techno-economical perspective, of the ratio between cogeneration and separate heat production for district-heating systems with heat demands below 50 GWh/year. The most profitable combined heat and power plant generates 45 % of the installed power in a 50 GWh system. The profit is, however, too low to justify any construction plans. The conclusion was that there are no economical reasons to choose combined heat and power based on an organic rankine cycle in Sweden today.</p>

<p>This project is a preliminary study in order to build a small power plant, located beside to Gavleån River. It has been designed with the aim of cooling a district of Gävle city, Sweden. That big project is carried out by the international consulting engineering company SWECO. The mentioned plant contains a thermodynamic cycle that takes water from the river and afterwards, it is returned back warmer. It will attempt to study the temperature raise downstream along the river due to the spill of hot water. In addition, it will try to quantify and weight which may be the importance of the increment of temperature compared to the entire river. This work could be vital for an environmental impact study. The thermo and fluid dynamic problem is going to be solved using typical procedure for numerical simulations. To do this, it will be used Computer Aided Design (CAD) to model Gavleån River path and Computational Fluent Dynamics (CFD) to predict the distribution of temperatures. Finally the results of the simulations will be analyzed and discussed to draw conclusions about the final temperature raise in Gavleån River.</p>

Ice based Cool Thermal Energy Storage (CTES) systems have attracted much attention during last few decades. The reasons are mainly of economical and environmental nature. Compared to conventional refrigeration and air-conditioning systems without cool thermal energy storage, implementation of CTES will increase environmental standards and overall efficiency of the energy systems as it contributes to the phase-out of synthetic refrigerants and reduces peak loads in electricity grids. For the application of a cool thermal energy storages in refrigeration installations and HVAC systems in industry and building sector, it is necessary to have appropriate design tools in order to sufficiently accurate predict their performance. In this thesis theoretical and experimental investigations of two ice based cool thermal energy storage systems, namely static, indirect, external melt, ice-on-coil, i.e. ice bank system and dynamic, ice slurry cool thermal energy storage system are carried out. An ice bank storage technology for cooling purposes is known for a long time. The main drawbacks which are hindering its wider use are the system complexity, high first costs, system efficiency which is highly dependant on design, control and monitoring of the system, etc. On the other hand, ice slurry technology was not well studied until recently, while in the current scientific literature there are still differences between results and conclusions reported by different investigators. The aim of the present thesis is to extend the knowledge in the field of ice based CTES systems, thereby contributing in the development and wider utilization of those systems. In the first part of the thesis a computer application, named “BankaLeda” is presented. It enables simulation of an ice bank system performance. In order to verify developed simulation model an experimental evaluation has been performed. Field measurements have been conducted on a two module silo which was installed as a part of the refrigeration system in dairy and cheese factory “Antun Bohnec” in the city of Ludbreg in Croatia. Experimental findings were compared to the simulation model. The software „BankaLeda“ presents a strong optimization tool for designers and engineers in the field by providing a high degree of freedom in defining particular system design and operating parameters. It offers a basis for assessment and testing of a new energy efficient system arrangements and measures. Besides it will give decisionmakers the ability to test potential solutions in the process of CTES system design. In the second part of the thesis ice slurry pressure drop and heat transfer in horizontal straight tubes have been experimentally investigated. In particular a mixture of 10.3 % of ethanol and water with an initial freezing point of -4.4 °C was considered. It was found that the behaviour of ice slurry flow is changing with time and that ice slurry pressure drop is generally higher than for single phase flow. However for ice concentrations of 15 % and higher, for certain velocities ice slurry pressure drop is found to be of a similar value as for single phase fluid. Moreover, if ice slurry is to be used as a energy transport media it is recommended to keep the ice mass fraction at a level of 20 %. With tube geometry and thermophysical properties of a carrier fluid the heat transfer of ice slurry is generally a function of ice mass fraction and velocity. The imposed heat flux has no or has just minor influence on the heat transfer coefficient. Up to ice mass fraction between 10-15 % the mean heat transfer coefficient shows only slight (laminar flow) or no increase (turbulent flow) in comparison to single phase flow. Beyond that ice mass fraction the heat transfer coefficient is increasing significantly. The test data for pressure drop and heat transfer in laminar and turbulent regime was compared to several correlations from the literature. A new correlations for ice slurry pressure drop and heat transfer in the laminar flow regime, for 10.3 % ethanol and water mixture, were derived based on the present experimental data. The correlation for pressure drop predicts 82 % of the experimental data with ±15 % accuracy, while the correlation for heat transfer predicts 75 % of the data with the same accuracy. In order to investigate advantages and disadvantages of a dynamic, ice slurry system over a static, indirect, external melt, ice-on-coil CTES system and to assess their differences from economical aspects, a theoretical simulation model of an ice slurry CTES have been developed. It was found that the ice slurry based CTES systems posses higher economic and energy saving potential than static type systems. In the best case scenario the total energy consumption of dynamic CTES system was found to be approximately 25 % lower than for a static CTES system. / QC 20100715

As a part of the fight against the global warming the energy production needs to be more efficient and redirected towards sustainable options. One alternative is cogeneration, which means that electricity and heat is produced in one plant. The purpose with this survey is to examine if there are any commercial available combined heat and power techniques, based on combustion of solid moist biomass, which are suitable to small-scale applications. The technique must be able to produce between 2 and 10 MW thermal and the heat demand is a Swedish district-heating system. When already published reports had been studied, the Organic Rankine Cycle (ORC) was chosen as the most suitable technique. The possibility of using the ORC to generate electricity from the district-heating return flow was considered simultaneously. The chosen ORC-technique was then evaluated in Excel. The first aspect to be examined was how the performance of a combined heat and power plant was affected by variations in the supply line temperature. It showed that the performance reaches top levels when the temperature is low. The second part contains an optimisation, in a techno-economical perspective, of the ratio between cogeneration and separate heat production for district-heating systems with heat demands below 50 GWh/year. The most profitable combined heat and power plant generates 45 % of the installed power in a 50 GWh system. The profit is, however, too low to justify any construction plans. The conclusion was that there are no economical reasons to choose combined heat and power based on an organic rankine cycle in Sweden today.

This project is a preliminary study in order to build a small power plant, located beside to Gavleån River. It has been designed with the aim of cooling a district of Gävle city, Sweden. That big project is carried out by the international consulting engineering company SWECO. The mentioned plant contains a thermodynamic cycle that takes water from the river and afterwards, it is returned back warmer. It will attempt to study the temperature raise downstream along the river due to the spill of hot water. In addition, it will try to quantify and weight which may be the importance of the increment of temperature compared to the entire river. This work could be vital for an environmental impact study. The thermo and fluid dynamic problem is going to be solved using typical procedure for numerical simulations. To do this, it will be used Computer Aided Design (CAD) to model Gavleån River path and Computational Fluent Dynamics (CFD) to predict the distribution of temperatures. Finally the results of the simulations will be analyzed and discussed to draw conclusions about the final temperature raise in Gavleån River.

Modeling of heat transfer using Dymola. In this report a evaporator, economizer and superheater where modeled. The report describes how the models where modeled and what input was most suitable for a accurate model.