This thesis tackles issues of particular interest regarding analysis and design of passive components at the mm-wave and Terahertz (THz) bands. Innovative analysis techniques and modeling of complex structures, design procedures, and practical implementation of advanced passive devices are presented. The first part of the thesis is dedicated to THz passive components. These days, THz technology suffers from the lack of suitable waveguiding structures since both, metals and dielectric, are lossy at THz frequencies. This implies that neither conventional closed metallic structures used at microwave frequencies, nor dielectric waveguides used in the optical regime, are adequate solutions. Among a variety of new proposals, the Single Wire Waveguide (SWW) stands out due to its low attenuation and dispersion. However, this surface waveguide presents difficult excitation and strong radiation on bends. A Dielectric-Coated Single Wire Waveguide (DCSWW) can be used to alleviate these problems, but advantages of the SWW are lost and new problems arise. Until now, literature has not given proper solution to radiation on bends and, on the other hand, rigorous characterization of these waveguides lacks these days. This thesis provides, for the first time, a complete modal analysis of both waveguides, appropriated for THz frequencies. This analysis is later applied to solve the problem of radiation on bends. Several structures and design procedures to alleviate radiation losses are presented and experimentally validated. The second part of the thesis is dedicated to mm-wave passive components. These days, when implementing passive components to operate at such small, millimetric wavelengths, to ensure proper metallic contact and alignment between parts results challenging. In addition, dielectric absorption becomes significant at mm-wave frequencies. Consequently, conventional hollow metallic waveguides and planar transmission lines present high attenuation so that new topologies are being considered. Gap Waveguides (GWs), based on a periodic structure introducing an Electromagnetic Bandgap effect, result very suitable since they do not require metallic contacts and avoid dielectric losses. However, although GWs have great potential, several issues prevent GW technology from becoming consolidated and universally used. On the one hand, the topological complexity of GWs difficulties the design process since full-wave simulations are time-costly and there is a lack of appropriate analysis methods and suitable synthesis procedures. On the other hand, benefits of using GWs instead of conventional structures are required to be more clearly evidenced with high-performance GW components and proper comparatives with conventional structures. This thesis introduces several efficient analysis methods, models, and synthesis techniques that will allow engineers without significant background in GWs to straightforwardly implement GW devices. In addition, several high-performance narrow-band filters operating at Ka-band and V-band, as well as a rigorous comparative with rectangular waveguide topology, are presented. / Esta tesis aborda problemas actuales en el análisis y diseño de componentes pasivos en las bandas de onda milimétrica y Terahercios (THz). Se presentan nuevas técnicas de análisis y modelado de estructuras complejas, procedimientos de diseño, e implementación práctica de dispositivos pasivos avanzados. La primera parte de la tesis se dedica a componentes pasivos de THz. Actualmente no se disponen de guías de onda adecuadas a THz debido a que ambos, metales y dieléctricos, introducen grandes pérdidas. En consecuencia, no es adecuado escalar las estructuras metálicas cerradas usadas en microondas, ni las guías dieléctricas usadas a frecuencias ópticas. Entre un gran número de recientes propuestas, la Single Wire Waveguide (SWW) destaca por su baja atenuación y casi nula dispersión. No obstante, como guía superficial, la SWW presenta difícil excitación y radiación en curvas. El uso de un recubrimiento dieléctrico, creando la Dielecric-Coated Single Wire Waveguide (DCSWW), alivia estos inconvenientes, pero las ventajas anteriores se pierden y nuevos problemas aparecen. Hasta la fecha, no se han encontrado soluciones adecuadas para la radiación en curvas de la SWW. Además, se echa en falta una caracterización rigurosa de ambas guías. Esta tesis presenta, por primera vez, un análisis modal completo de SWW y DCSWW, adecuado a la banda de THz. Este análisis es aplicado posteriormente para evitar el problema de la radiación en curvas. Se presentan y validan experimentalmente diversas estructuras y procedimientos de diseño. La segunda parte de la tesis abarca componentes pasivos de ondas milimétricas. Actualmente, estos componentes sufren una importante degradación de su respuesta debido a que resulta difícil asegurar contacto metálico y alineamiento adecuados para la operación a longitudes de onda tan pequeñas. Además, la absorción dieléctrica incrementa notablemente a estas frecuencias. En consecuencia, tanto guías metálicas huecas como líneas de transmisión planares convencionales presentan gran atenuación, siendo necesario considerar topologías alternativas. Las Gap Waveguides (GWs), basadas en una estructura periódica que introduce un efecto de Electromagnetic Bandgap, resultan muy adecuadas puesto que no requieren contacto entre partes metálicas y evitan las pérdidas en dieléctricos. No obstante, a pesar del potencial de las GWs, varias barreras impiden la consolidación y uso universal de esta tecnología. Por una parte, la compleja topología de las GWs dificulta el proceso de diseño dado que las simulaciones de onda completa consumen mucho tiempo y no existen actualmente métodos de análisis y diseño apropiados. Por otra parte, es necesario evidenciar el beneficio de usar GWs mediante dispositivos GW de altas prestaciones y comparativas adecuadas con estructuras convencionales. Esta tesis presenta diversos métodos de análisis eficientes, modelos, y técnicas de diseño que permitirán la síntesis de dispositivos GW sin necesidad de un conocimiento profundo de esta tecnología. Asimismo, se presentan varios filtros de banda estrecha operando en las bandas Ka y V con altas prestaciones, así como una comparativa rigurosa con la guía rectangular. / Aquesta tesi aborda problemes actuals en relació a l'anàlisi i disseny de components passius en les bandes d'ona mil·limètrica i Terahercis. Es presenten noves tècniques d'anàlisi i modelatge d'estructures complexes, procediments de disseny, i implementació pràctica de dispositius passius avançats. La primera part de la tesi es focalitza en components passius de THz. Actualment no es disposen de guies d'ona adequades a THz causa que tots dos, metalls i dielèctrics, introdueixen grans pèrdues. En conseqüència, no és adequat escalar les estructures metál·liques tancades usades en microones, ni les guies dielèctriques usades a freqüències òptiques. Entre un gran nombre de propostes recents, la Single Wire Waveguide (SWW) destaca per la seua baixa atenuació i quasi nul·la dispersió. No obstant això, com a guia superficial, la SWW presenta difícil excitació i radiació en corbes. L'ús d'un recobriment dielèctric, creant la Dielecric-Coated Single Wire Waveguide (DCSWW), alleuja aquests inconvenients, però els avantatges anteriors es perden i nous problemes apareixen. Fins a la data, no s'han trobat solucions adequades per a la radiació en corbes de la SWW. A més, es troba a faltar una caracterització rigorosa d'ambdues guies. Aquesta tesi presenta, per primera vegada, un anàlisi modal complet de SWW i DCSWW, adequat a la banda de THz. Aquest anàlisi és aplicat posteriorment per evitar el problema de la radiació en corbes. Es presenten i validen experimentalment diverses estructures i procediments de disseny. La segona part de la tesi es centra en components passius d'ones mil·limètriques. Actualment, aquests components pateixen una important degradació de la seua resposta a causa de que resulta difícil assegurar contacte metàl·lic i alineament adequats per a l'operació a longituds d'ona tan menudes. A més, l'absorció dielèctrica incrementa notablement a aquestes freqüències. En conseqüència, tant guies metàl·liques buides com línies de transmissió planars convencionals presenten gran atenuació, sent necessari considerar topologies alternatives. Les Gap Waveguides (GWs), basades en una estructura periòdica que introdueix un efecte de Electromagnetic Bandgap, resulten molt adequades ja que no requereixen contacte entre parts metàl·liques i eviten les pèrdues en dielèctrics. No obstant, tot i el potencial de les GWs, diverses barreres impedixen la consolidació i ús universal d'aquesta tecnologia. D'una banda, la complexa topologia de les GWs dificulta el procés de disseny atés que les simulacions d'ona completa consumeixen molt de temps i no existeixen actualment mètodes d'anàlisi i disseny apropiats. D'altra banda, és necessari evidenciar el benefici d'utilitzar GWs mitjançant dispositius GW d'altes prestacions i comparatives adequades amb estructures convencionals. Aquesta tesi presenta diversos mètodes d'anàlisi eficients, models, i tècniques de disseny que permetran la síntesi de dispositius GW sense necessitat d'un coneixement profund d'aquesta tecnologia. Així mateix, es presenten diversos filtres de banda estreta operant en les bandes Ka i V amb altes prestacions, així com una comparativa rigorosa amb la guia rectangular. / Berenguer Verdú, AJ. (2017). Analysis and design of efficient passive components for the millimeter-wave and THz bands [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/84004

Este trabalho apresenta um método desenvolvido pela autora para, através de simulações multifísicas pelo Método dos Elementos Finitos (MEF), servir como ferramenta de apoio ao projeto e fabricação de guias de onda e moduladores eletro-ópticos em óptica integrada, além de possibilitar a análise da performance de moduladores eletro-ópticos. A técnica adotada para a fabricação dos guias de onda ópticos foi a de tensão mecânica. Os parâmetros de geometria (espessura do filme e larguras das trincheiras) e de temperatura de deposição do filme são definidos nas simulações e utilizados no processo de fabricação de guias de ondas em óptica integrada, que servem de base para a fabricação de moduladores eletro-ópticos em substrato cristalino de retículo cúbico. As trincheiras dos guias de onda do tipo canal são construídas em Germanato de Bismuto (BGO - Bi4Ge3O12), a partir da deposição sobre o substrato de um filme fino indutor de tensão mecânica (stress) Nitreto de Silício (Si3N4) e definidas pelos processos de litografia óptica e corrosão seletiva por plasma. Os moduladores são obtidos através da deposição dos eletrodos de alumínio sobre o filme, seguida de Si3N4 dos processos de litografia óptica e corrosão, obtendo-se eletrodos. O processo iterativo proposto inicia-se com os resultados das simulações, em que são definidos os parâmetros de fabricação do filme, da trincheira e dos eletrodos. Após a fabricação desses elementos, o componente é caracterizado e são medidos os parâmetros reais filme e do substrato. Esses valores são realimentados nas simulações para refinar o projeto do componente. O trabalho, além de apresentar todos os passos do processo interativo de simulações, projeto, fabricação e caracterização do componente desejado, indica as dificuldades encontradas na implementação do processo e as atividades futuras a serem desenvolvidas para o aperfeiçoamento do mesmo. / This work presents a method developed by the author to support the project and fabrication of integrated optic waveguides and electro-optic modulators by means of Finite Element Method (FEM) multiphysics simulations, also enabling the electro-optic modulators performance analysis. The technique used for fabricating the optical waveguides was the thermally induced residual stress (ISS). The geometry parameters (film thicknesses and trenches widths) and the film deposition temperature are obtained in the simulations and subsequently used in the integrated optical waveguides fabrication process, which serve as a basic building block for the electrooptic modulators on crystalline cubic lattice substrate. The channel waveguide trenches are built on Bismuth Germanate (BGO Bi4Ge3O12) by depositing a Silicon Nitride (Si3N4) Stress-inducing thin film, being later defined by optical lithography and plasma etching process. Modulators are obtained depositing aluminum on the Si3N4 film followed by the optical lithography and corrosion process, defining electrodes. The proposed iterative process starts with the simulation results that define the fabrication parameters of the film, trench and electrodes. After the fabrication of these elements, the device is characterized and the actual parameters of the film and substrate are measured. These values are fed back into the simulations to refine the component design. The work besides presenting all the simulation-design-fabrication-characterization iterative process for obtaining the devised device also highlights the difficulties encountered in the implementation process along with suggestions of future activities aiming at improving it.

This thesis presents various integrated antenna solutions for different types of systems and applications, e.g. wireless sensors, broadband handsets, advanced base stations, MEMS-based reconfigurable front-ends, automotive anti-collision radars, and large area electronics. For wireless sensor applications, a T-matched dipole is proposed and integrated in an electrically small body-worn sensor node. Measurement techniques are developed to characterize the port impedance and radiation properties. Possibilities and limitations of the planar inverted cone antenna (PICA) for small handsets are studied experimentally. Printed slot-type and folded PICAs are demonstrated for UWB handheld terminals. Both monolithic and hybrid integration are applied for electrically steerable array antennas. Compact phase shifters within a traveling wave array antenna architecture, on single layer substrate, is investigated for the first time. Radio frequency MEMS switches are utilized to improve the performance of reconfigurable antennas at higher frequencies. Using monolithic integration, a 20 GHz switched beam antenna based on MEMS switches is implemented and evaluated. Compared to similar work published previously, complete experimental results are here for the first time reported. Moreover, a hybrid approach is used for a 24 GHz switched beam traveling wave array antenna. A MEMS router is fabricated on silicon substrate for switching two array antennas on a LTCC chip. A concept of nano-wire based substrate integrated waveguides (SIW) is proposed for millimeter-wave applications. Antenna prototypes based on this concept are successfully demonstrated for automotive radar applications. W-band body-worn nonlinear harmonic radar reflectors are proposed as a means to improve automotive radar functionality. Passive, semi-passive and active nonlinear reflectors consisting of array antennas and nonlinear circuitry on flex foils are investigated. A new stretchable RF electronics concept for large area electronics is demonstrated. It incorporates liquid metal into microstructured elastic channels. The prototypes exhibit high stretchability, foldability, and twistability, with maintained electrical properties. / wisenet

No description available.

No description available.

[pt] Neste trabalho são analisadas junções entre guias coaxiais não homogêneos com perdas. A expansão modal dos campos eletromagnéticos em um guia coaxial com duas camadas radiais é detalhadamente deduzida, e posteriormente a formulação é generalizada para guias com multicamadas radiais. As constantes de propagação para guias com perdas são determinadas pelo método do winding number, garantindo que todos os autovalores possam ser encontrados. O método do casamento de modos é aplicado na análise e projeto de estruturas coaxiais. A formulação é aplicada na otimização de estruturas de acoplamento e cornetas radiantes com carregamento dielétrico não homogêneo. O preenchimento não homogêneo é empregado nas estruturas radiantes a fim de minimizar a perda de retorno, e principalmente controlar e melhorar o formato do diagrama de radiação para operação em banda larga. Adicionalmente, a formulação é utilizada para analisar a propagação eletromagnética em sistemas de telemetria sem fio para poços de petróleo. / [en] In this work, we analyzed junctions between coaxial waveguides heterogeneously filled with lossy dielectrics. The modal expansion of the electromagnetic fields in a coaxial waveguide with two radial layers is derived in detail, and afterward the formulation is generalized for a multilayer waveguide. The propagation constants for lossy waveguides are determined through the method of winding number, ensuring that all eigenvalues can be found. The mode matching technique is applied in the analysis and design of coaxial structures. The formulation is applied in the optimization of coupling structures and radiating horns with heterogeneous dielectric loading. The heterogeneous filling is used in radiating structures in order to reduce the return loss, and especially to control and improve the shape of the radiation pattern for broadband operation. Additionally, the formulation is used to analyze the electromagnetic propagation in wireless telemetry systems for oil wells.

Manipulating light by controlling surface plasmons on metals is being discussed as a means for bridging the size gap between micrometer-sized photonic circuits and nanometer-sized integrated electronics. Plasmonic waveguides based on metal nanoparticles are of particular interest for circumventing the diffraction limit, thereby enabling high-speed communication over short-range distances in miniaturized micro-components. However, scalable, inexpensive fine-tuning of particle assemblies remains a challenge and near-field probing is required to reveal plasmonic interactions. In this thesis, self-assembled waveguides should be produced on DNA scaffolds. DNA origami is an extremely versatile and robust self-assembly method which allows scalable production of nanostructures with a fine control of assemblies at the nanoscale. To form the plasmonic waveguides, six-helix bundle DNA origami nanotubes are used as templates for attachment of highly monodisperse and monocrystalline gold nanoparticles with an inter-particle distance of 1-2 nm. In the first part of this thesis, the effects of parameters which are involved in assembly reactions are systematically investigated. The assembly yield and binding occupancy of the gold nanoparticles are determined by an automated, high-throughput image analysis of electron micrographs of the formed complexes. As a result, unprecedented binding site occupancy and assembly yield are achieved with the optimized synthesis protocol. In addition, waveguides with different sizes of gold nanoparticles and different inter-particle distances, quantum dots attachments to the waveguides and multimerization of the waveguides are successfully realized. In the second part of this thesis, direct observation of energy transport through a self-assembled waveguide towards a fluorescent nanodiamond is demonstrated. High-resolution, near-field mapping of the waveguides are studied by electron energy loss spectroscopy and cathodoluminescence imaging spectroscopy. The experimental and simulation results reveal that energy propagation through the waveguides is enabled by coupled surface plasmon modes. These surface plasmon modes are probed at high spatial and spectral resolutions. The scalable self-assembly approach presented here will enable the construction of complex, sub diffraction plasmonic devices for applications in high-speed optical data transmission, quantum information technology, and sensing. / Die Manipulation des Lichts durch die Kontrolle von Oberflächenplasmonen auf metallischen Oberflächen und Nanopartikeln gilt als vielversprechende Methode zur Überbrückung der Größen-Lücke zwischen Mikrometer-großen photonischen und nanometer-großen elektronischen Schaltkreisen. Plasmonische Wellenleiter basierend auf metallischen Nanopartikeln sind vom besonderen Interesse, da sie die Umgehung des Beugungslimits und somit eine Hochgeschwindigkeitskommunikation über kurze Distanzen in immer kleiner werdenden Schaltkreisen ermöglichen könnten. Allerdings ist die skalierbare und kostengünstige Anordnung von Partikeln eine große Herausforderung und es werden Nahfelduntersuchungen benötigt um plasmonische Interaktionen detektieren zu können. Das Ziel dieser Arbeit ist die Selbstassemblierung von multi-partikel Wellenleitern auf DNA Gerüsten. Die Verwendung von DNA-Origami bietet eine äußerst vielseitige Plattform zur skalierbaren Herstellung von Nanostrukturen mittels Selbstassemblierung und ermöglicht eine präzise Kontrolle der Anordnungen im Nanobereich. Für den Aufbau der plasmonischen Wellenleiter werden DNA-Origami Nanoröhren, bestehend aus sechs Helices als Templat für die Anbindung von monodispersen und monokristallinen Goldnanopartikeln mit einem interpartikulären Abstand von 1-2 nm verwendet. Im ersten Abschnitt dieser Arbeit werden die beeinflussenden Faktoren dieser Assemblierungsreaktion systematisch untersucht. Die Ausbeute der assemblierten Strukturen und die Besetzung der Bindungsstellen werden durch eine automatisierte und effiziente Bildanalyse von Elektronenmikroskopieaufnahmen ausgewertet. Durch die Entwicklung eines optimierten Syntheseprotokolls werden bisher unerreichte Assemblierungsausbeuten ermöglicht. Zusätzlich erfolgen die experimentelle Realisierung von Strukturen mit verschieden großen Goldnanopartikeln und unterschiedlichen interpartikulären Abständen, sowie die Anbindung von Quantenpunkten an die Wellenleiter und eine Verknüpfung der assemblierten Strukturen. Der zweite Abschnitt dieser Dissertation befasst sich mit der Untersuchung des Energietransports in selbstassemblierten Wellenleitern über einen fluoreszierenden Nanodiamanten. Dazu erfolgen hochaufgelöste Nahfeldmessungen der Wellenleiter mittels Elektronenenergieverlustspektroskopie und Kathodolumineszenz-mikroskopie. Die experimentellen Ergebnisse und zusätzlich durchgeführte Simulationen bestätigen eine durch gekoppelte Oberflächenplasmonenmoden induzierte Weitergabe der Energie innerhalb des Wellenleiters. Diese Oberflächenplasmonenmoden werden bei hoher räumlicher und spektraler Auflösung untersucht. Das hier umgesetzte Konzept der Selbstassemblierung wird den Aufbau komplexer plasmonischer Geräte für Anwendungen im Bereich der optischen Hochgeschwindigkeitsdatenübertragung, der Quanteninformations-technolgie und der Sensorik ermöglichen.

Este trabalho apresenta um método desenvolvido pela autora para, através de simulações multifísicas pelo Método dos Elementos Finitos (MEF), servir como ferramenta de apoio ao projeto e fabricação de guias de onda e moduladores eletro-ópticos em óptica integrada, além de possibilitar a análise da performance de moduladores eletro-ópticos. A técnica adotada para a fabricação dos guias de onda ópticos foi a de tensão mecânica. Os parâmetros de geometria (espessura do filme e larguras das trincheiras) e de temperatura de deposição do filme são definidos nas simulações e utilizados no processo de fabricação de guias de ondas em óptica integrada, que servem de base para a fabricação de moduladores eletro-ópticos em substrato cristalino de retículo cúbico. As trincheiras dos guias de onda do tipo canal são construídas em Germanato de Bismuto (BGO - Bi4Ge3O12), a partir da deposição sobre o substrato de um filme fino indutor de tensão mecânica (stress) Nitreto de Silício (Si3N4) e definidas pelos processos de litografia óptica e corrosão seletiva por plasma. Os moduladores são obtidos através da deposição dos eletrodos de alumínio sobre o filme, seguida de Si3N4 dos processos de litografia óptica e corrosão, obtendo-se eletrodos. O processo iterativo proposto inicia-se com os resultados das simulações, em que são definidos os parâmetros de fabricação do filme, da trincheira e dos eletrodos. Após a fabricação desses elementos, o componente é caracterizado e são medidos os parâmetros reais filme e do substrato. Esses valores são realimentados nas simulações para refinar o projeto do componente. O trabalho, além de apresentar todos os passos do processo interativo de simulações, projeto, fabricação e caracterização do componente desejado, indica as dificuldades encontradas na implementação do processo e as atividades futuras a serem desenvolvidas para o aperfeiçoamento do mesmo. / This work presents a method developed by the author to support the project and fabrication of integrated optic waveguides and electro-optic modulators by means of Finite Element Method (FEM) multiphysics simulations, also enabling the electro-optic modulators performance analysis. The technique used for fabricating the optical waveguides was the thermally induced residual stress (ISS). The geometry parameters (film thicknesses and trenches widths) and the film deposition temperature are obtained in the simulations and subsequently used in the integrated optical waveguides fabrication process, which serve as a basic building block for the electrooptic modulators on crystalline cubic lattice substrate. The channel waveguide trenches are built on Bismuth Germanate (BGO Bi4Ge3O12) by depositing a Silicon Nitride (Si3N4) Stress-inducing thin film, being later defined by optical lithography and plasma etching process. Modulators are obtained depositing aluminum on the Si3N4 film followed by the optical lithography and corrosion process, defining electrodes. The proposed iterative process starts with the simulation results that define the fabrication parameters of the film, trench and electrodes. After the fabrication of these elements, the device is characterized and the actual parameters of the film and substrate are measured. These values are fed back into the simulations to refine the component design. The work besides presenting all the simulation-design-fabrication-characterization iterative process for obtaining the devised device also highlights the difficulties encountered in the implementation process along with suggestions of future activities aiming at improving it.

Wave propagation is a phenomenon resulting from high transient loadings where the duration of the load is in µ seconds range. In aerospace and space craft industries it is important to gain knowledge about the high frequency characteristics as it aids in structural health monitoring, wave transmission/attenuation for vibration and noise level reduction. The wave propagation problem can be approached by the conventional Finite Element Method(FEM); but at higher frequencies, the wavelengths being small, the size of the finite element is reduced to capture the response behavior accurately and thus increasing the number of equations to be solved, leading to high computational costs. On the other hand such problems are handled in the frequency domain using Fourier transforms and one such method is the Spectral Finite Element Method(SFEM). This method is introduced first by Doyle ,for isotropic case and later popularized in developing specific purpose elements for structural diagnostics for inhomogeneous materials, by Gopalakrishnan. The general approach in this method is that the partial differential wave equations are reduced to a set of ordinary differential equations(ODEs) by transforming these equations to another space(transformed domain, say Fourier domain). The reduced ODEs are usually solved exactly, the solution of which gives the dynamic shape functions. The interpolating functions used here are exact solution of the governing differential equations and hence, the exact elemental dynamic stiffness matrix is derived. Thus, in the absence of any discontinuities, one element is sufficient to model 1-D waveguide of any length. This elemental stiffness matrix can be assembled to obtain the global matrix as in FEM, but in the transformed space. Thus after obtaining the solution, the original domain responses are obtained using the inverse transform. Both the above mentioned manuscripts present the Fourier transform based spectral finite element (FSFE), which has the inherent aliasing problem that is persistent in the application of the Fourier series/Fourier transforms. This is alleviated by using an additional throw-off element and/or introducing slight damping in to the system. More recently wave let transform based spectral finite element(WSFE) has been formulated which alleviated the aliasing problem; but has a limitation in obtaining the frequency characteristics, like the group speeds are accurate only up-to certain fraction of the Nyquist(central frequency). Currently in this thesis Laplace transform based spectral finite elements(LSFE) are developed for sandwich members. The advantages and limitations of the use of different transforms in the spectral finite element framework is presented in detail in Chapter-1. Sandwich structures are used in the space craft industry due to higher stiffness to weight ratio. Many issues considered in the design and analysis of sandwich structures are discussed in the well known books(by Zenkert, Beitzer). Typically the main load bearing structures are modeled as beam sand plates. Plate structures with kh<1 is analysed based on the Kirch off plate theory/Classical Plate Theory(CPT) and when the bending wavelength is small compared to the plate thickness, the effect of shear deformation and rotary inertia needs to be included where, k is the wave number and h is the thickness of the plate. Many works regarding the wave propagation in sandwich structures has been published in the past literature for wave propagation in infinite sandwich structure and giving the complete description of dispersion relation with no restriction on frequency and wavelength. More recently exact analytical solution or simply supported sandwich plate has been derived. Also it is seen by comparison of dispersion curves obtained with exact (3D formulation of theory of elasticity) and simplified theories (2D formulation as generalization of Timoshenko theory) made on infinite domain and concluded that the simplified theory can be reliably used to assess the waveguide properties of sandwich plate in the frequency range of interest. In order to approach the problems with finite domain and their implementation in the use of general purpose code; finite degrees of freedom is enforced. The concept of displacement based theories provides the flexibility in assuming different kinematic deformations to approach these problems. Many of the displacement based theories incorporate the Equivalent Single Layer(ESL) approach and these can capture the global behavior with relative ease. Chapter-2 presents the Laplace spectral finite element for thick beams based on the First order Shear Deformation Theory (FSDT). Here the effect of different choices of the real part of the Laplace variable is demonstrated. It is shown that the real part of the Laplace variable acts as a numerical damping factor. The spectrum and dispersion relations are obtained and the use of these relations are demonstrated by an example. Here, for sandwich members based on FSDT, an appropriate choice of the correction factor ,which arises due to the inconsistency between the kinematic hypothesis and the desired accuracy is presented. Finally the response obtained by the use of the element is validated with experimental results. For high shock loading cases, the core flexibility induces local effects which are very predominant and this can lead to debonding of face sheets. The ESL theories mentioned above cannot capture these effects due to the computation of equivalent through the thickness section properties. Thus, higher order theories such as the layer-wise theories are required to capture the local behaviour. One such theory for sandwich panels is the Higher order Sandwich Plate theory (HSaPT). Here, the in-plane stress in the core has been neglected; but gives a good approximation for sandwich construction with soft cores. Including the axial inertial terms of the core will not yield constant shear stress distribution through the height of the core and hence more recently the Extended Higher order Sandwich Plate theory (EHSaPT) is proposed. The LSFE based on this theory has been formulated and is presented in Chapter-4. Detailed 3D orthotropic properties of typical sandwich construction is considered and the core compressibility effect of local behavior due to high shock loading is clearly brought out. As detailed local behavior is sought the degrees of freedom per element is high and the specific need for such theory as compared with the ESL theories is discussed. Chapter-4 presents the spectral finite element for plates based on FSDT. Here, multi-transform method is used to solve the partial differential equations of the plate. The effect of shear deformation is brought out in the spectrum and dispersion relations plots. Response results obtained by the formulated element is compared and validated with many different experimental results. Generally structures are built-up by connecting many different sub-structures. These connecting members, called joints play a very important role in the wave transmission/attenuation. Usually these joints are modeled as rigid joints; but in reality these are flexible and exhibits non-linear characteristics and offer high damping to the energy flow in the connected structures. Chapter-5 presents the attenuation and transmission of wave energy using the power flow approach for rigid joints for different configurations. Later, flexible spectral joint model is developed and the transmission/attenuation across the flexible joints is studied. The thesis ends with conclusion and highlighting futures cope based on the developments reported in this thesis.

Les micro-résonateurs optiques comptent parmi les dispositifs les plus importants en photonique. Les résonateurs WGM sont assez particuliers. Il s'agit de composant présentant une symétrie circulaire comme c'est le cas des sphères, des anneaux, des disques et des tores. Les résonateurs WGM présentent un facteur de qualité exceptionnel et un volume modal très faible. Ces appareils peuvent être utilisés dans plusieurs domaines, notamment la télédétection, le filtrage optique et l'optique non linéaire. D'autres applications sont possibles en biologie, médecine, spectroscopie moléculaire, surveillance environnementale, astronomie et astrophysique grâce à l'exploitation du rayonnement moyen infrarouge. Les micro-résonateurs optiques comportent un grand nombre de transitions vibrationnelles qui agissent comme des «empreintes» pour de nombreuses molécules organiques permettant le développement d'applications spectroscopiques innovantes et de nouveaux capteurs. Il convient de noter que l'atmosphère de la terre est transparente au niveau des deux fenêtres de transmission atmosphérique. La première est comprise entre 3 et 5 μm et la seconde entre 8 et 13 μm, ce qui rend possible des applications telles que la détection d'explosifs à distance ainsi que le brouillage de communication confidentielles. La large fenêtre de transparence en verres de chalcogénures dans le domaine spectral infrarouge rend envisageable le développement de nombreuses applications. Les verres de chalcogénure sont caractérisés par une bonne résistance mécanique et une durabilité chimique suffisante dans l'eau et l'atmosphère. Par ailleurs, l'indice de réfraction élevé, le rendement quantique élevé, l'énergie de phonon faible et la solubilité importante des terres rares permettent des émissions dans le domaine spectral du moyen IR. Dans cette thèse, la conception de dispositifs innovants en chalcogénure pour des applications utilisant le moyen infrarouge est étudiée en utilisant un code d'ordinateur personnel formé de façon aléatoire. Les appareils reposent sur des trois types de micro-résonateurs : les microsphères, les micro-disques et les microbulles. Les résonateurs WGM sont efficacement excités à l'aide de fibres nervurées et de guides d'ondes optiques de forme conique. Le nouveau procédé de conception est développé en utilisant la méthode d'optimisation par essaims particulaires (PSO). Elle permet de maximiser le gain d'un amplificateur reposant sur une microsphère d'émission laser dopée à l'erbium à 4,5 μm. Une technique innovante permettant de caractériser les propriétés spectroscopiques de la terre rare intégrant la recherche électromagnétique en mode WGM grâce à l'algorithme PSO a été développée. Les valeurs récupérées sont entachées d’une erreur inférieure à celle prévue par les instruments de mesure ayant un coût élevé. Des applications intéressantes peuvent être obtenues en excitant le micro-résonateur avec une fibre conique présentant deux LPG identiques sur les côtés. En effet, les FLP peuvent sélectionner le couplage de modes de fibre avec le résonateur WGM. En utilisant différentes paires de FLP identiques, opérant dans différentes bandes de longueurs d'onde, il est possible de coupler de façon sélective différents résonateurs à l'aide de la même fibre optique. Un code informatique aléatoire a été développé et validé. Il a démontré la faisabilité d'un capteur de microbulles de glucose. Un microdisque en terre rare dopé est étudié pour obtenir une source de lumière compacte et économique dans l'infrarouge moyen. Un code informatique est développé afin de simuler un micro-disque de terre rare dopé et associé à deux guides d'ondes nervurés, un pour le signal et l'autre pour la pompe. Le modèle est validé à l'aide d'un micro-disque dopée à l'erbium émettant à 4,5 μm. Ce dispositif très prometteur pour des applications dans le moyen infrarouge est obtenu en utilisant un micro-disque de praséodyme dopé émettant à 4,7 μm. / Optical micro-resonators represent one of the most important devices in photonics. A special kind is constituted by the WGM resonators, i.e. devices with circular symmetry such as spheres, rings, disks and toroids. They are characterized by very small dimensions, exceptionally quality factor and very low modal volume becoming a valuable alternative to the traditional optical micro-resonators, such as Fabry-Pérot cavities. These devices allow applications in several fields, such as sensing, optical filtering and nonlinear optics. In particular, different applications in biology and medicine, molecular spectroscopy, environmental monitoring, astronomy and astrophysics are feasible in Mid-Infrared wavelength range. For example, it includes a lot of strong vibrational transitions that act as “fingerprints” of many bio-molecules and organic species allowing the develop of innovative spectroscopic applications and novel sensors. In addition, the earth's atmosphere is transparent in two atmospheric transmission windows at 3–5 μm and 8–13 μm and then applications such as remote explosive detection, e.g. in airports and for border control, and covert communication systems are feasible. The wide transparency window of chalcogenide glasses in Mid-Infrared makes possible the development of several devices. Chalcogenide glasses are characterized by good mechanical strength and chemically durability in water and atmosphere. Furthermore, the high refractive index, high quantum efficiency, the low phonon energy and high rare-earth solubility enables the emissions at long wavelengths.In this thesis, the design of innovative chalcogenide devices for applications in Mid-Infrared is investigated using an ad-hoc home-made computer code. The devices are based on three kinds of micro-resonators: microspheres, micro-disks and microbubbles. The WGM resonators are efficiently excited by using tapered fiber and ridge waveguides. A novel design procedure is developed using the particle swarm optimization approach (PSO). It allows to maximize the gain of an amplifier based on an erbium-doped microsphere lasing at 2.7 μm.An innovative technique in order to characterize the spectroscopic properties of rare-earth is developed integrating the WGM electromagnetic investigation with PSO algorithm. The method is based on two subsequent steps: in the first one, the geometrical parameters are recovered, in the second one, the spectroscopic parameters. The recovered values are affected by an error less than that provided by high-cost measurement instruments. Furthermore, the procedure is very versatile and could be applied to develop innovative sensing systems.Interesting applications could be obtained exciting the micro-resonator by a tapered fiber with two identical LPGs on the sides. Indeed the LPGs can select the fiber modes coupling with the WGM resonator. Using different pairs of identical LPGs operating in different wavelength bands, it is possible to selective couple different micro-resonators by using the same optical fiber. An ad-hoc computer code is developed and validated and it demonstrated the feasibility of a microbubble glucose sensor.In order to obtain a compact and cost-saving light source in Mid-Infrared, rare-earth doped micro-disk are investigated. A computer code is developed in order to simulate a rare-earth doped micro-disk coupled to two ridge waveguide, one at signal wavelength and the other one at pump wavelength. The model is validated using an erbium-doped micro-disk emitting at 4.5 μm. A very promising device for application in Mid-Infrared is obtained using a praseodymium-doped micro-disk emitting at 4.7 μm.