Inom tillverkning är skärande bearbetning en vanligt förekommande process och däribland borrning.Verktygskostnader har stor påverkan på den totala tillverkningskostnaden då till exempel ett heltarbetsstycke i värsta fall kan gå förlorat vid verktygshaveri. Genom sitt arbete med ständigaförbättringar håller Scania sig konkurrenskraftiga med sina produkter av hög kvalitet. I dettaexamensarbete inom masterprogrammet Industriell Produktion på KTH har en specifik typ av borrmed löstagbar borrkrona utvärderats med avsikt att undersöka nya fabrikat.Uppdragsgivaren var motorbearbetningen (DM) på Scania i Södertälje. Arbetet inleddes med attinförskaffa relevant kunskap gällande verktyget som undersöktes. Samtidigt utfördes ennulägesanalys där de använda borrarna på DM kartlades tillsammans med information kring pris,livslängd, m.m. Utifrån kartläggingen sammanställdes statistik som analyserades för att identifierahur stor påverkan en eventuell standardisering skulle kunna ha.Utvärderingen av borrar bestod av praktiska experiment där sju olika verktyg med en diameter på12,2 mm testades under samma förhållanden. Testet utformades i enighet med berörda parter påDM samt efter studier av adekvat litteratur rörande borrexperiment. Fyra parametrar testadesutöver borrarnas livslängd. Dessa var axialkraft, förslitning, håldiameter och spånor. Parametrarnaämnades jämföras och analyseras för att dra slutsatser kring borrarnas prestationer.Nulägesanalysen visade att ett fabrikat utgjorde hela 69% av borrarna på hela DM. Efter slutfördaborrtester hade enbart tre av sju genomfört utan haveri, Borr E, F och G. Samtliga sju borrar visadegodkända spånor och höll sig inom toleranserna för angiven håldiameter. Axialkrafterna varierademellan borrarna där Borr F hade lägst krafter och Borr A högst. Borr E visade bäst motstånd motförslitningar. Utifrån detta valdes borrarna E, F och G att rekommenderas för deras goda prestationermed Borr E på första plats. Utöver det föreslogs att utbudet av fabrikat som kan användas på DMbegränsas för att uppnå kostnadsbesparingar gällande verktygen. / Drilling is a common cutting process within manufacturing. Tool costs have great influence on thetotal manufacturing cost since a tool break down can cause an entire work piece to be scrapped.Through their constant work with improvements, Scania stays competitive with their high qualityproducts. This Master Thesis in Industrial Production and Management at KTH has evaluated aspecific type of drill with indexable heads with the purpose of investigating new brands.The Engine Manufacturing department (DM) at Scania in Södertälje requested this project. The taskwas initiated by obtaining knowledge about the tool that were to be investigated. Simultaneously ananalysis of the current state was performed where the drills at DM were mapped out withinformation regarding price, tool life, etc. The statistics were compiled and analysed to identify theeffect of an eventual standardisation.The evaluation consisted of practical experiments where seven different drills with a diameter of12,2 mm was tested under the same circumstances. The test was design in concurrence with affectedparts at DM and studies of adequate literature regarding drilling experiments. Four parameters weretested in addition to the tool life of the drills. These were axial force, tool wear, hole diameter andchips. The parameters were intended to be used for comparing and analysing in order to makeconclusions regarding the performance of the drills.The current state analysis showed that one brand represented 69% of the drills used at DM. Afterfinished drilling tests three out of seven drills managed to complete the test without tool breakdown. All drills produced chips that were acceptable and the measured diameters stayed within thegiven tolerances. The axial forces varied between the drill where Borr F had the lowest force and BorrA the highest. Borr E showed the best resistance against tool wear. From the results the drills thatwere recommended were Borr E, F and G because of their good performances with Borr E in the firstplace. Ultimately it was suggested to limit the amount of brands used at DM to achieve cost savingsregarding the tools.

[pt] Este trabalho apresenta um estudo do comportamento dinâmico de uma bancada de testes representativa do sistema real de perfuração, composta por um motor CC acoplado a um sistema físico torcional, sujeita a fontes de atrito que induzem um regime de stick-slip no sistema em duas regiões distintas. O estudo incluiu a identificação de parâmetros da bancada de testes por meio de uma série de ensaios experimentais; e a caracterização do atrito, por meio do levantamento experimental da curva do coeficiente de atrito, em função da velocidade angular dos rotores principais. O intuito inicial foi a obtenção de um modelo numérico que fosse o mais simples possível e que representasse bem a bancada de testes. Uma vez obtido o modelo numérico, prosseguiu-se com uma série de simulações que permitissem uma caracterização indireta do regime de atrito ao qual estivessem submetidos os rotores principais, partindo-se apenas de medições de parâmetros no motor. Esse estudo é de grande relevância para a compreensão qualitativa da dinâmica do sistema real de perfuração, uma vez que ainda hoje não há técnicas totalmente confiáveis para caracterização do comportamento da coluna no fundo do poço a partir de dados da superfície somente. / [en] This paper presents a study of the dynamic behavior of a representative test bench of a real rotary drilling system, comprising a DC motor coupled to a very exible torsional system subjected to sources of friction which can induce self-excitation into two distinct regions of the system. The study includes the identification of parameter settings from the test bench by means of a series of experimental tests and characterization of friction, by obtaining the experimental curve of the friction coefficient as a function of the angular speed of the main rotor. The initial aim was to obtain a numerical model as simple as possible, capable of representing the test bench. Once obtained the numerical model, a series of numerical simulations were done, which allow an indirect characterization of the friction condition to which main rotors were subjected, starting only with the parameters measured at the drive. This study is of great importance for a qualitative understanding of the dynamics of the real drilling system, since today there is no fully reliable techniques to characterize the behavior of the column in the deep from surface data only.

[pt] Prospecção de petróleo usa um equipamento chamado coluna de perfuração para escavar o solo até o nível do reservatório. Este equipamento é uma longa coluna, sob rotação, composto por uma sequência de tubos de perfura ção e equipamentos auxiliares conectados. A dinâmica desta coluna é muito complexa, porque sob condições normais de operação, ela está sujeita à vibrações longitudinais, laterais e torcionais, que apresentam um acoplamento não-linear. Além disso, a estrutura está submetida a efeitos de atrito e choque devido a contatos mecânicos entre os pares broca/rocha e tubos de perfuração/parede do poço. Este trabalho apresenta um modelo mecânico-matemático para analisar uma coluna de perfuração em configuração horizontal. Este modelo usa uma teoria de viga com inércia de rotação, deformação cisalhante e acoplamento não-linear entre os três mecanismos de vibração. As equações do modelo são discretizadas utilizando o método dos elementos finitos. As incertezas dos parâmetros do modelo de interação broca-rocha são levandas em conta através de uma abordagem probabilística paramétrica, e as distribuições de probabilidades dos parâmetros aleatórios são construídas por meio do princípio da entropia máxima. Simulações numéricas são conduzidas de forma a caracterizar o comportamento dinâmico não-linear da estrutura, especialmente, da broca. Fenômenos dinâmicos inerentemente não-lineares, como stick-slip e bit-bounce, são observados nas simulações, bem como choques. Uma análise espectral mostra que, surpreendentemente, os fenômenos de stick-slip e bit-bounce são resultado do mecanismo de vibração lateral, e que os fenômenos de choque decorrem da vibração torcional. Visando aumentar a eficiência do processo de perfuração, um problema de otimização que tem como objetivo maximizar a taxa de penetração da coluna no solo, respeitando os seus limites estruturais, é proposto e resolvido. / [en] Oil prospecting uses an equipment called drillstring to drill the soil until the reservoir level. This equipment is a long column under rotation, composed by a sequence of connected drill-pipes and auxiliary equipment. The dynamics of this column is very complex because, under normal operational conditions, it is subjected to longitudinal, lateral, and torsional vibrations, which presents a nonlinear coupling. Also, this structure is subjected to friction and shocks effects due to the mechanical contacts between the pairs drill-bit/soil and drill-pipes/borehole. This work presents a mechanical-mathematical model to analyze a drillstring in horizontal configuration. This model uses a beam theory which accounts rotatory inertia, shear deformation, and the nonlinear coupling between three mechanisms of vibration. The model equations are discretized using the finite element method. The uncertainties in bit-rock interaction model parameters are taken into account through a parametric probabilistic approach, and the random parameters probability distributions are constructed by means of maximum entropy principle. Numerical simulations are conducted in order to characterize the nonlinear dynamic behavior of the structure, specially, the drill-bit. Dynamical phenomena inherently nonlinear, such as slick-slip and bit-bounce, are observed in the simulations, as well as shocks. A spectral analysis shows, surprisingly, that slick-slip and bit-bounce phenomena result from the lateral vibration mechanism, and that shock phenomena comes from the torsional vibration. Seeking to increase the efficiency of the drilling process, an optimization problem that aims to maximize the rate of penetration of the column into the soil, respecting its structural limits, is proposed and solved. / [fr] La prospection de pétrole utilise un équipement appelé tube de forage pour forer le sol jusqu au niveau du réservoir. Cet équipement est une longue colonne rotative, composée d une série de tiges de forage interconnectées et d équipements auxiliaires. La dynamique de cette colonne est très complexe car dans des conditions opérationnelles normales, elle est soumise à des vibrations longitudinales, latérales et de torsion, qui présentent un couplage non linéaire. En outre, cette structure est soumise à des effets de frottement et à des chocs dûs aux contacts mécaniques entre les paires tête de forage/sol et tube de forage/sol. Ce travail présente un modèle mécaniquemathématique pour analyser un tube de forage en configuration horizontale. Ce modèle utilise la théorie des poutres qui utilise l inertie de rotation, la déformation de cisaillement et le couplage non linéaire entre les trois mécanismes de vibration. Les équations du modèle sont discrétisées par la méthode des éléments finis. Les incertitudes des paramètres du modèle d interaction tête de forage/sol sont prises en compte par l approche probabiliste paramétrique, et les distributions de probabilité des paramètres aléatoires sont construites par le principe du maximum d entropie. Des simulations numériques sont réalisées afin de caractériser le comportement dynamique non lináaire de la structure, et en particulier, de l outil de forage. Des phénom ènes dynamiques non linéaires par nature, comme le slick-slip et le bit- bounce, sont observés dans les simulations, ainsi que les chocs. Une analyse spectrale montre étonnamment que les phénomènes slick-slip et bit-bounce résultent du mécanisme de vibration latérale, et ce phénomène de choc vient de la vibration de torsion. Cherchant à améliorer l efficacité de l opération de forage, un problème d optimisation, qui cherche à maximiser la vitesse de pénétration de la colonne dans le sol, sur ses limites structurelles, est proposé et résolu.

No description available.

Growing knowledge in the field of cognitive science can significantly improve the way we learn. Several methods and principles are being repeatedly confirmed by numerous studies as effective for learning. They include spaced repetition, test-enhanced learning, and desirable difficulty principle. With the continual spreading of ICT technologies, diverse software is being developed as well, some of which more and some of which less successfully employs the methods and principles outlined. Memrise, Purpose Games and Drill and Skill, web platforms which are examined in this thesis, belong to this software family. In the first phase, i conducted several interviews with teachers who were using Drill and Skill as part of their science teaching at elementary schools and a junior grammar school (all of them were teaching children approx. 11-15 years old). After this, i worked with a class from a grammar school (age around 16). i made several groups of educational games to help the students practice the topics studied in their biology lessons. Each group of games was reviewed during a group interview. Recordings from these interviews as well as from the interviews with the teachers were transcribed and these transcripts underwent qualitative analysis, which is an important part of the thesis. Drawing on all...

O fenômeno de stick-slip, no processo de perfuração de poços de petróleo, é propiciado pela interação entre broca e formação rochosa e pode dar origem a grandes oscilações na velocidade angular podendo provocar danos irreparáveis ao processo. Neste trabalho, analisa-se o desempenho de leis de controle aplicadas à mesa rotativa (responsável por movimentar a coluna de perfuração), visando à redução de stick-slip e de oscilações da velocidade angular da broca. As leis de controle implementadas são do tipo PI (Proporcional-Integral), com parcelas de torque aplicado à mesa rotativa, proporcional e integral à velocidade da mesa, podendo ser com peso na broca constante ou variável. Para a coluna de perfuração, foi proposto um modelo em elementos finitos com função de forma linear. O torque na broca foi modelado segundo atrito de Coulomb pela forma não regularizada, curva esta ajustada pelos dados empíricos conforme propostas da literatura. Diversos critérios de desempenho foram analisados e foi observado que a minimização do desvio médio da velocidade angular em relação à referência propicia melhores condições de operação. Análises paramétricas dos ganhos de controle proporcional e integral foram realizadas, dando origem a curvas de nível para o desvio médio de velocidade angular na broca. A partir destas curvas, foram definidas regiões de estabilidade nas quais o desvio é aceitável. Estas regiões foram observadas serem maiores para menores pesos na broca e maiores velocidades angulares de referência e vice-versa. A adição do controle do peso na broca permitiu uma redução global dos níveis de desvio médio de velocidade angular, dando origem a um aumento das regiões de estabilidade do processo de perfuração. / The stick-slip phenomenon, in the process of drilling oil wells, due to the interaction between drill and rock formation can lead to large fluctuations in drill-bit angular velocity and, thus, cause irreparable damage to the process. In this work, the performance of control laws applied to the rotary table (responsible for moving the drill string) is analyzed, in order to reduce stick-slip and drill-bit angular velocity oscillations. The control laws implemented are based on a PI (Proportional-Integral) controller, for which the torque applied to the rotating table has components proportional and integral to table angular velocity with constant or variable WOB (Weight On Bit). For the drillstring, a finite element model with a linear interpolation was proposed. The torque on the drill-bit was modeled by a non-regularized Coulomb friction model, with parameters that were adjusted using empirical data proposed in literature. Several performance criteria were analyzed and it was observed that the minimization of the mean deviation of the drill-bit angular velocity relative to the target one would provide the best operating condition. Parametric analyses of proportional and integral control gains were performed, yielding level curves for the mean deviation of drill-bit angular velocity. From these curves, stability regions were defined in which the deviation is acceptable. These regions were observed to be wider for smaller values of WOB and higher values of target angular velocity and vice-versa. The inclusion of a controlled dynamic WOB reduced the levels of mean deviation of angular velocity, leading to improved stability regions for the drilling process.

Endosseous implants have notably high success rates, yet a small percentage of implants still fail for unidentified reasons. Recent literature points to hyperglycemia, resulting from untreated or undiagnosed diabetes, as a possible contraindication in an otherwise apparently healthy population. To investigate the effect of surface design on peri-implant healing in the presence of hyperglycemia, STZ-treated rats were implanted with custom rectangular implants of two surface topographies: grit blasted (GB) and grit-blast with a calcium phosphate nanotopography (GB-DCD). Tensile testing was conducted at 5, 7, and 9 days post-operative. Results demonstrated hyperglycemia to delay early stages of the peri-implant healing. Contact osteogenesis was increased along the GB-DCD surface, even in an environment of uncontrolled hyperglycemia, and the GB-DCD surface outperformed the GB surface in both healthy and hyperglycemic animals, showing peri-implant bone matured more rapidly on nanotopographically complex surfaces, even in the presence of uncontrolled hyperglycemia.

Made available in DSpace on 2014-12-17T14:06:57Z (GMT). No. of bitstreams: 1 SheylaKJM_DISSERT.pdf: 2022444 bytes, checksum: 199284d45ddc8db628d0e2f45da9a7e8 (MD5) Previous issue date: 2011-01-17 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior / The present work is to study the characteristics and technological properties of soil-cement bricks made from binary and ternary mixtures of Portland cement, sand, water, with or without addition of gravel from the drilling of oil wells, which could be used by industry, aiming to improve its performance and reduce cost by using the residue and, consequently, increasing its useful life. The soil-cement bricks are one of the alternatives to masonry construction. These elements, after a short curing period, provide compressive strength similar to that of solid bricks and ceramic blocks, and the higher the resistance the higher the amount of cement used. We used the soil from the city of S?o Jos? do Mipibu / RN, the banks of the River Baldun, cement CPIIZ-32 and residue of drill cuttings from oil wells drilling onshore wells in the town of Mossley, RN, provided Petrobras. To determine the optimum mix, we studied the inclusion of different residues (100%, 80%, 70%, 60% and 50%) where 15 bodies were made of the test piece. The assessment was made of bricks made from simple compression tests, mass loss by immersion and water absorption. The experimental results proved the efficiency and high utilization of the waste from the drilling of oil wells, making the brick-cement-soil residue with a higher strength and lower water absorption. The best result in terms of mechanical strength and water absorption for the ternary mixture was 10% soil, 14% cement and 80% residue. In terms of binary mixtures, we obtained the best result for the mix-cement residue, which was 14% cement incorporated in the residue / O presente trabalho consiste no estudo das caracter?sticas e propriedades tecnol?gicas de tijolos solo-cimento formulados a partir de misturas bin?rias e tern?rias de cimento Portland, areia, ?gua, com e sem adi??o de cascalho proveniente da perfura??o de po?os de petr?leo, que poder?o ser utilizados pela ind?stria, com o objetivo de melhorar seu desempenho e diminuir seu custo utilizando o res?duo e, conseq?entemente, aumentando sua vida ?til. Os tijolos de solo-cimento constituem uma das alternativas para a constru??o em alvenaria. Esses elementos, ap?s pequeno per?odo de cura, garantem resist?ncia ? compress?o simples similar ? dos tijolos maci?os e blocos cer?micos, sendo a resist?ncia tanto mais elevada quanto maior for ? quantidade de cimento empregada. Foi utilizado o solo proveniente do Munic?pio de S?o Jos? do Mipib?/RN, as margens do Rio Baldun, cimento CPIIZ-32 e res?duo de cascalho de perfura??o de po?os de petr?leo proveniente da perfura??o de po?os Onshore, no munic?pio de Mossor?/RN, fornecido pela Petrobras. Para a determina??o da mistura ?tima, estudou-se a inclus?o de teores de res?duos diferenciados (100%; 80%; 70%; 60% e 50%) onde foram confeccionados 15 corpos-de-prova. A avalia??o dos tijolos confeccionados foi feita a partir de ensaios de compress?o simples, perda de massa por imers?o e absor??o de ?gua. Os resultados experimentais comprovaram a efici?ncia e o elevado potencial de utiliza??o do res?duo proveniente da perfura??o de po?os de petr?leo, tornando o tijolo de solo-cimento-res?duo com uma maior resist?ncia mec?nica e menor absor??o de ?gua. O melhor resultado, em termos de resist?ncia mec?nica e absor??o d ?gua, para a mistura tern?ria, foi de 10% de solo, 14% de cimento e 80% de res?duo. Em termos de misturas bin?rias, obteve-se o melhor resultado para a combina??o cimento-res?duo, que foi de 14% de cimento incorporado no res?duo

Made available in DSpace on 2014-12-17T14:07:20Z (GMT). No. of bitstreams: 1 MoacirGS_TESE.pdf: 4771867 bytes, checksum: f93165e08f62a97944b6eed01b488995 (MD5) Previous issue date: 2012-02-10 / Among the industries, those that produce ceramic porcelain for use in construction industry and oil, during the exploration and production period, play an important role in the production of waste. Much research has been carried out both by academia and the productive sector, sometimes reintroducing them in the same production line that generated them, sometimes in areas unrelated to their generation, as in the production of concrete and mortar for the construction, for example, but each one in an isolated way. In this research, the aim is to study the combined incorporation of the waste drill cuttings of oil well and the residue of the polishing of porcelain, generated in the final stage of finishing of this product in a clay matrix, for the production of red pottery, specifically bricks, ceramic blocks and tiles. The clay comes from the municipality of S?o Gon?alo, RN, the drilling waste is from the Natal basin, in Rio Grande do Norte, and the residue of the polishing proceeds from a ceramic porcelain of the State of Para?ba. For this purpose, we used a mixture of a plastic clay with a non-plastic, in a ratio of 50% each, settling formulations with the addition of these two residues in this clay matrix. In the formulations, both residues were incorporated with a minimum percentage of 2.5% and maximum of 12.5%, varying from 2.5% each, in each formulation, which the sum of the waste be no more than 15%. It should be noted that the residue of the polishing of ceramic porcelain is a IIa class (not inert). The materials were characterized by XRF, XRD, TG, DTA, laser granulometry and the plasticity index. The technological properties of water absorption, apparent porosity, linear shrinkage of burning, flexural tensile strength and bulk density were evaluated after the sintering of the pieces to 850 ?C, 950 ?C and 1050 ?C, with a burning time of 3 hr, 3 hr and 30 minutes, and 3 hr and 50 minutes, respectively, with a heating rate of 10 ?C/minute, for all formulations and landing of 30 minutes. To better understand the influence of each residue and temperature on the evaluated properties, we used the factorial planning and its surfaces of response for the interpretation of the results. It was found that the temperature has no statistical significance at a 95% of reliability level in flexural tensile strength and that it decreases the water absorption and the porosity, but increases the shrinkage and the bulk density. The results showed the feasibility of the desired incorporation, but adjusting the temperature to each product and formulation, and that the temperatures of 850 ?C and 950 ?C were the one that responded to the largest number of formulations / A ind?stria de produ??o de porcelanatos para uso na constru??o civil e a do petr?leo, na fase de explora??o e produ??o, exercem um papel importante na produ??o de res?duos. Muitas pesquisas t?m sido realizadas tanto pela academia quanto pelo setor produtivo, ora reintroduzindo esses res?duos na mesma linha de produ??o que os gerou, ora em setores alheios ao de sua gera??o, como na produ??o de concretos e argamassas para a constru??o civil, por exemplo, mas cada um de forma isolada. O objetivo desta pesquisa ? estudar a incorpora??o combinada do res?duo de cascalho de perfura??o de po?o petrol?fero e do res?duo do polimento do porcelanato, gerado na fase de acabamento final do produto, numa matriz argilosa, para a produ??o de cer?mica vermelha - especificamente tijolos, blocos cer?micos e telhas. A argila utilizada ? oriunda do munic?pio de S?o Gon?alo do Amarante, RN; o res?duo de perfura??o, da bacia potiguar, no Rio Grande do Norte; e o do polimento ? de uma cer?mica de porcelanato do Estado da Para?ba. Utilizou-se a mistura de uma argila pl?stica com uma n?o pl?stica, numa propor??o de 50 % de cada uma (que ? o percentual de mistura adotado na cer?mica fornecedora dessa argila), estabelecendo-se formula??es com a incorpora??o dos dois res?duos nessa matriz argilosa. Nas formula??es, os dois res?duos foram incorporados com um percentual m?nimo de 2,5 % e m?ximo de 12,5 %, variando-se em 2,5 % cada um, em cada formula??o, de modo que a soma dos res?duos fosse no m?ximo 15 %. ? oportuno registrar que o res?duo do polimento do porcelanato ? de classe IIa (n?o inerte). Os materiais foram caracterizados por FRX, DRX, TG, DTA, granulometria a laser e pelo ?ndice de plasticidade. As propriedades tecnol?gicas de absor??o de ?gua, porosidade aparente, retra??o linear de queima, tens?o de ruptura ? flex?o e massa espec?fica aparente, foram avaliadas ap?s a sinteriza??o das pe?as a 850 ?C, 950 ?C e 1050 ?C, com ciclo de queima de 3 h , 3 h e 30 min e 3 h e 50 min, respectivamente, com taxa de aquecimento de 10 ?C/min. e patamar de 30 min., para todas as formula??es. Para melhor compreender-se a influ?ncia de cada res?duo e de cada temperatura nas propriedades avaliadas, utilizou-se o planejamento fatorial e suas superf?cies de resposta para interpreta??o dos resultados. Verificou-se que a temperatura n?o tem signific?ncia estat?stica no n?vel de 95 % de confiabilidade na tens?o de ruptura ? flex?o e que ela diminui a absor??o de ?gua e a porosidade, mas aumenta a retra??o e a massa espec?fica aparente. Os resultados mostraram a viabilidade da incorpora??o pretendida, adequando-se a temperatura a cada produto e cada formula??o, e as temperaturas de 850 ?C e 950 ?C foram as que atenderam ao maior n?mero de formula??es

Le perçage vibratoire auto entretenu propose la rupture technologique nécessaire à une augmentation de la performance du perçage profond. Un porte outil spécifique a été conçu pour permettre les vibrations axiales, et se présente sous la forme d'un système masse ressort, dont les caractéristiques sont identifiés par l'utilisation de la théorie des lobes de stabilité. L'identification des caractéristiques géométriques d'un outil optimal passe par la caractérisation des aspects tribologiques, des caractéristiques mécaniques du matériau usiné, ainsi que la définition d'une préparation d'arête adéquate. Enfin, ce procédé étant piloté par l'énergie de la coupe, deux modèles d'effort ont été identifiés. La méthode CAM repose sur la discrétisation de l'effort de perçage lors de la phase de pénétration, alors que l'approche analytique permet de prédire l'effort à partir d'un modèle de coupe analytique identifié à partir d'essais de coupe oblique. / Self-sustained vibration drilling offers the technological breakthrough needed to increase the performance of deep drilling. A special tool holder is designed to allow axial vibration, and comes as a spring mass system, whose characteristics are identified by the use of the theory of stability lobes. Identification of the geometric characteristics of an optimal tool requires the characterization of tribological aspects, mechanical properties of the machined material, and the definition of a proper edge preparation. Finally, this process is driven by the energy of the cut, and two types of effort have been identified. The Edge-Material-Pair Method is based on the discretization of the drilling thrust force during penetration phase, while the analytical approach can predict forces from a cut pattern identified from oblique cutting tests.