This study focused on independent EFL reading among Grade 11 students across public and non-public schools in Ethiopia. Students who practice independent reading develop a love for reading and ultimately become life-long self-initiated readers. Therefore, independent reading should be considered as a vital goal of instruction and research. The issues of focus in this study were students’ reading comprehension ability levels, attitude towards learning English as a school subject and reading its literature, reading motivation, reading strategy use, persistence in independent reading and access to reading resources along with inclusion of independent reading in classroom instruction and in English textbooks. To this end, the study used quantitative data (collected through reading comprehension test, structured questionnaire and independent reading follow-up checklist) and qualitative data (gathered via classroom observation and content analysis).The findings revealed lower predisposition towards and practice of independent EFL reading among public school students (n = 375). A statistically significant difference, in favour of non-public schools (n = 181), was also found between the two groups of students in scores pertaining to most of the variables investigated. Enhanced scaffolding of independent reading through improved instruction and resource provision, regular short refresher courses for teachers of English and further studies have been recommended to improve public school students’ involvement in independent EFL reading. / English Studies / D. Litt. et Phil. (English Studies)

This research sought to investigate the impact of a belief in witchcraft as an explanation for all the ills in the Hlubi community and South African societies in general - which becomes a good tool for inadequate governments. Our approach in this study has been interdisciplinary and the utilization of comparative analysis and a combination of phenomenological and qualitative research models. Economic problems create social tensions and are manifested in various ways, including witchcraft craze. The Hlubi scenario found parallels in Europe and America. Witchcraft and ancestors are considered to be the main causes of diseases but nature and ecological or environmental dangers are other factors. Pragmatic and obvious response to such phobias is seen in the protective and preventive devices provided by isangoma, amaqhira, amaxhwere, inyanga and faith healers. It is hypothesized that as long as all existential needs exist in Hlubi society witchcraft will continue to be with us, perhaps forever. / Religious Studies and Arabic / DLITT ET PHIL (REL STUD)

Background: The South Africa’s reproductive health policy put more emphasis on dual methods in preventing unwanted pregnancies, sexually transmitted infections (STIs) and Human Immunodeficiency Virus (HIV) transmission. Regardless of such policies, the uptake of voluntary counselling and testing (VCT) services remains a personal choice. Aim: The purpose of the study was to determine the accessibility, acceptance and utilisation of VCT services by women on hormonal contraceptives. Methods: About 134 women obtaining hormonal contraceptives were interviewed in a cross-sectional study. Descriptive and logistic regression analysis was applied to analyse the study data. Results: Respondents displayed positive attitudes towards Human Immunodeficiency Virus (HIV) testing. Unavailability and poor access to in-house VCT services was found to be a barrier for use of these services. Conclusion: There’s a need for provider initiated counselling and testing (PICT) strengthening and integration of VCT services into family planning. / Public Health / M.P.H. (Public Health)

No description available.

Les caractéristiques et les propriétés de libération de microparticules chargées de médicament dépendent de la nature des matériaux employés, des propriétés physicochimiques des microparticules, du choix de la méthode de production, et enfin des propriétés des molécules encapsulées. A l'inverse de la plupart des méthodes conventionnelles, les méthodes microfluidiques présentent l’avantage de bien mieux contrôler la génération de gouttelettes, leur taille et leur distribution de tailles. Ainsi des dispositifs microfluidiques à base de capillaires ont été développés pour obtenir des microbilles de polymère mais également des microparticules de type janus, coeur-écorce ou troyenne, toutes monodisperses en taille et chargées de médicament(s). Ces particules ont été produites à partir de solutions de monomère qui furent polymérisées par irradiations UV de telle sorte à garder intacte l'activité des molécules chargées. Ces dispositifs peuvent être assemblés dans un court laps de temps et un simple changement dans leur conception permet d’obtenir des morphologies de particules très différentes. Ces particules ont été développées dans le but de résoudre les problèmes rencontrés dans l’administration orale de médicaments. Par exemple les microbilles peuvent être utilisées pour délivrer des anti-inflammatoires non stéroïdiens de manière continue tandis que les particules Janus peuvent libérer, simultanément et sur le même site, deux principes actifs possédant des propriétés complètement différentes (solubilité, compatibilité) également de manière prolongée. Quant aux particules coeur-écorce, elles ont été conçues pour cibler la région du côlon de l'intestin humain, et y libérer simultanément deux médicaments. Les particules troyennes furent synthétisées à l’aide d’un procédé microfluidique semi-continu qui a permis une manipulation plus sécurisée des nanoparticules vectrices ainsi que la libération continue d’un médicament dans un liquide gastrique simulé. Chaque système a été entièrement caractérisé pour assurer l’invariance entre lots et la reproductibilité. En général, la libération des ingrédients actifs a pu être facilement contrôlée/ajustée par le réglage des paramètres opératoires et de matériaux tels que les débits des différentes phases, la nature et la concentration du médicament, des (co)monomères, des agents tensioactif et de réticulation, le pH du milieu de libération. Ces différents paramètres influencent les propriétés des microparticules telles que leur morphologie, forme, taille et densité de réticulation du réseau polymère. / Characteristics and release properties of drug loaded microparticles depend upon material used and choice of production method. Conversely to most of the conventional ones, microfluidic methods give an edge by improving the control over droplet generation, size and size distribution. Capillary-based microfluidic devices were successfully used to obtain monodisperse drug(s) loaded microbeads, janus, core-shell and trojan particles using UV initiated free radical polymerization while keeping activity of active loaded molecules. These devices can be assembled in a short period of time and a slight change in design gives completely different microparticles morphologies. These particles were developed with the aim to address different issues experienced in oral drug delivery. For instance microbeads can be used to deliver NASIDs in a sustained release manner while janus particles can release two APIs with completely different properties (solubility, compatibility) also in a sustained release manner. Core-shell particles were designed to target colonic region of human intestine for dual drug delivery. Trojan particles were synthesized in a new semi-continuous microfluidic process, thus improving nanoparticles safety handling and release in simulated gastric fluid. Each system was fully characterized to insure batch to batch consistency and reproducibility. In general, the release of active ingredients was controlled by tuning the operating and material parameters like phases flow rates, nature and concentration of drug, (co)monomers, surfactant and crosslinker, pH of release media with the result of different particle morphologies, sizes and shapes or matrix crosslinking density.

The poly(glycidyl methacrylate)-modified magnetite nanoparticles, Fe3O4-PGMA NPs, were investigated and applied in nondestructive flaw detection of polymeric materials in this research. The Fe3O4 endowed magnetic property to the materials for flaw detection while the PGMA promoted colloidal stability and prevented particle aggregation. The magnetite nanoparticles (Fe3O4 NPs) were successfully synthesized by coprecipitation and then surface-modified with PGMA to form PGMA-modified Fe3O4 NPs by both grafting-from and grafting-to approaches. For the grafting-from approach, the Fe3O4 NPs were surface-functionalized with α-bromo isobutyryl bromide (BIBB) to form BIB-modified Fe3O4 NPs (Fe3O4-BIB NPs) with covalent linkage. The resultant Fe3O4-BIB NPs were used as surface-initiators to grow PGMA by surface-initiated atom transfer radical polymerization (SI-ATRP). For the grafting-to approach, the Fe3O4 NP were surface-functionalized with (3-mercaptopropyl)triethoxysilane (MCTES) to form MCTES-modified Fe3O4 NPs (Fe3O4-MCTES NPs). The PGMA with Br-end group was pre-synthesized by ATRP and then was grafted to the surface of the Fe3O4-MCTES NPs by coupling reaction. Both bare and modified Fe3O4 NPs exhibited superparamagnetism and the existence of iron oxide in the form of Fe3O4 was confirmed. The particle size of individual Fe3O4 NPs was about 8 – 24 nm but they aggregated to form clusters. The PGMA-modified NPs formed stable dispersion in chloroform and had larger cluster sizes than the unmodified ones because of the PGMA polymer layer. However, the uniformity of the NP clusters could be improved with PGMA surface grafting. The PGMA surface layer of the grafting-from (Fe3O4-gf-PGMA) NPs was thin and dense while that of the grafting-to (Fe3O4-gt-PGMA) NPs was thick and loose. The hydrodynamic diameters (Zave) of Fe3O4-gf-PGMA NP clusters could be controlled between 176 to 643 nm, dependent on the PGMA contents and reaction conditions. During SI-ATRP, side reactions happened and caused NP aggregation as well as increase of size of NP clusters. However, the aggregation has been minimized through optimization of reaction conditions. Oppositely, Zave values of Fe3O4-gt-PGMA NPs had little variation of about 120 – 190 nm. And the PGMA content of the Fe3O4-gt-PGMA NPs was limited to 12.5% because of the spatial hindrance during grafting process. The saturation magnetization (Ms) of the unmodified Fe3O4 NPs was about 77 emu/g, while those of the grafting-from and grafting-to Fe3O4-PGMA NPs were 50 – 66 emu/g and 63 – 70 emu/g, respectively. For Fe3O4-PGMA NPs with similar Fe3O4 contents, the grafting-to NPs had slightly higher Ms than the grafting-from counterparts. In addition, the Ms of both kinds of the Fe3O4-PGMA NPs with higher Fe3O4 content (> 87%) were also higher than that of the fluidMAG-Amine, the commercially available amine-modified MNPs. Besides, both kinds of Fe3O4-PGMA NPs also had much higher Fe3O4 contents and Ms values than most of the reported PGMA-modified MNPs. The magnetic epoxy nanocomposites (MENCs) were prepared by blending the modified Fe3O4 NPs into bisphenol A diglycidyl ether (BADGE)-based epoxy system and the distributions of both kinds of the PGMA-modified NPs were much better than that of the oleic acid-modified Fe3O4 NPs. Similar to the NPs, the MENCs also exhibited superparamagnetism. By cross-section TEM observation, the grafting-to Fe3O4-PGMA NPs formed more homogeneous distributions with smaller cluster size than the grafting-from counterparts and gave higher Ms of the MENCs. Nondestructive flaw detection of surface and sub-surface defects could be successfully achieved by brightness contrast of images given through eddy current testing (ET) method, which is firstly reported. The mechanical properties of the materials were influenced very slightly when 2.5% or lower Fe3O4-gt-PGMA NPs were present while the presence of the Fe3O4-gf-PGMA NPs (1 – 2.5 %) gave mild improvement of the storage modulus and increase of the glass-rubber transition temperature(Tg) of the MENCs. Furthermore, the Fe3O4-PGMA NPs could be evenly coated onto the functionalized ultra-high molecular weight poly(ethylene) (UHMWPE) textiles. The Fe3O4-gt-PGMA NPs were coated on the textile in order to prepare NP-coated textile-reinforced composite. Preliminary result of ET measurement showed that the Fe3O4-gt-PGMA NPs coated on the textiles could visualize the structure of the textile hidden inside and their relative depth. Accordingly, the incorporation of MNPs to polymers opens a new pathway of damage-free structural health monitoring of polymeric materials.

L'objectif de ce travail est de caractériser et de modéliser le comportement mécanique des oxydes d'uranium (UO2) en situation d'Accident d'Injection de Réactivité (RIA). Les sollicitations vues par le combustible durant un RIA sont caractérisées par de fortes vitesses de déformation (jusqu'à 1/s) et de fortes températures (1000-2500°C). Deux lots de pastilles d'UO2 (de type industriel et à forte densité) ont donc fait l'objet d'une campagne d'essais de compression à vitesses de déplacements imposées (0,1-100 mm/min auxquelles correspondent des vitesses de déformations de 10−4-10−1/s) et à températures régulées (1100-1350-1550-1700°C). Les résultats expérimentaux obtenus (évolution de la géométrie, de la contrainte d'écoulement et de la microstructure) ont permis de définir un modèle de fluage en sinus hyperbolique ainsi qu'un critère de Drucker-Prager avec plasticité associée, modélisant la fragmentation des joints de grain à l'échelle macroscopique. Des simulations Éléments Finis de ces essais et de plus de 200 essais de fluage ont servi à valider la réponse du modèle sur une grande gamme de températures (1100°C-1700°C) et de vitesses de déformation (10−9-10−1/s). Enfin, une loi de comportement dite L3F (Loi Fluage Fissuration Fracturation des joints de grain) a été développée pour l'UO2 en ajoutant, au modèle précédent, le fluage d'irradiation et la fissuration macroscopique en traction. Cette loi a alors été utilisée dans le code crayon combustible ALCYONE-RIA pour simuler, à l'aide d'une modélisation 1,5D, les essais REP-Na effectués dans le réacteur expérimental CABRI. Les résultats de simulation sont en bon accord avec les observations post-essais. / The aim of this work is to characterize and model the mechanical behavior of uranium dioxide (UO2) during a Reactivity Initiated Accident (RIA). The fuel loading during a RIA is characterized by high strain rates (up to 1 /s) and high temperatures (1000°C - 2500°C). Two types of UO2 pellets (commercial and high density) were therefore tested in compression with prescribed displacement rates (0.1 to 100 mm / min corresponding to strain rates of 10-4 - 10-1 /s) and temperatures (1100°C - 1350°C - 1550°C et 1700°C). Experimental results (geometry, yield stress and microstructure) allowed us to define a hyperbolic sine creep law and a Drucker-Prager criterion with associated plasticity, in order to model grain boundaries fragmentation at the macroscopic scale. Finite Element Simulations of these tests and of more than 200 creep tests were used to assess the model response to a wide range of temperatures (1100°C - 1700°C) and strain rates (10-9 /s - 10-1 /s). Finally, a constitutive law called L3F was developed for UO2 by adding to the previous model irradiation creep and tensile macroscopic cracking. The L3F law was then introduced in the 1.5D scheme of the fuel performance code ALCYONE-RIA to simulate the REP-Na tests performed in the experimental reactor CABRI. Simulation results are in good agreement with post tests examinations.

The researcher of this study " Indian Migrants and Self-Initiated Expatriates in the host Countries: the Focus on Social Support" the whole study about the Indian expatriates who are living in the United Kingdom and the main goal of this research is to predict how successful the Indian expatriates in their settling process in the UK and the focus of social supports. The sample includes both Self-initiated expatriates ( SIE's) and Assigned Expatriates(AE's). SIE's expatriates are Indian students who are studying in the UK and the AE's expatriates are the company assigned Indian full-time employees. Social support includes briefly the overall host country support provided for Indian expatriates in the host country. Social support is measured in three broader dimensions pertinent to Waxin cross-cultural adjustment model (2006), likely perceived organizational support, individual self-motivation, and contextual support, includes family support and host country environment. (Navas et al, 2005) classified six relevant contexts of acculturation of expatriates in a foreign country, which emphasize, politics and government, organizational work-related adjustments, economic perspective, family relations; social relations and ideology, which includes religious belief and customs. The structure of the thesis covers extensive theoretical part based on the intense review of literature in the field of expatriation, cross-cultural studies, information on this context about the United Kingdom and India and final part includes practical data analysis, business cases and recommendation for the future research.

This critical review summarizes recent developments in the fabrication of patterned polymer brushes. As top-down lithography reaches the length scale of a single macromolecule, the combination with the bottom-up synthesis of polymer brushes by surface-initiated polymerization becomes one main avenue to design new materials for nanotechnology. Recent developments in surface-initiated polymerizations are highlighted along with diverse strategies to create patterned polymer brushes on all length scales based on irradiation (photo- and interference lithography, electron-beam lithography), mechanical contact (scanning probe lithography, soft lithography, nanoimprinting lithography) and on surface forces (capillary force lithography, colloidal lithography, Langmuir–Blodgett lithography) (116 references). / Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG-geförderten) Allianz- bzw. Nationallizenz frei zugänglich.

The poly(glycidyl methacrylate)-modified magnetite nanoparticles, Fe3O4-PGMA NPs, were investigated and applied in nondestructive flaw detection of polymeric materials in this research. The Fe3O4 endowed magnetic property to the materials for flaw detection while the PGMA promoted colloidal stability and prevented particle aggregation. The magnetite nanoparticles (Fe3O4 NPs) were successfully synthesized by coprecipitation and then surface-modified with PGMA to form PGMA-modified Fe3O4 NPs by both grafting-from and grafting-to approaches. For the grafting-from approach, the Fe3O4 NPs were surface-functionalized with α-bromo isobutyryl bromide (BIBB) to form BIB-modified Fe3O4 NPs (Fe3O4-BIB NPs) with covalent linkage. The resultant Fe3O4-BIB NPs were used as surface-initiators to grow PGMA by surface-initiated atom transfer radical polymerization (SI-ATRP). For the grafting-to approach, the Fe3O4 NP were surface-functionalized with (3-mercaptopropyl)triethoxysilane (MCTES) to form MCTES-modified Fe3O4 NPs (Fe3O4-MCTES NPs). The PGMA with Br-end group was pre-synthesized by ATRP and then was grafted to the surface of the Fe3O4-MCTES NPs by coupling reaction. Both bare and modified Fe3O4 NPs exhibited superparamagnetism and the existence of iron oxide in the form of Fe3O4 was confirmed. The particle size of individual Fe3O4 NPs was about 8 – 24 nm but they aggregated to form clusters. The PGMA-modified NPs formed stable dispersion in chloroform and had larger cluster sizes than the unmodified ones because of the PGMA polymer layer. However, the uniformity of the NP clusters could be improved with PGMA surface grafting. The PGMA surface layer of the grafting-from (Fe3O4-gf-PGMA) NPs was thin and dense while that of the grafting-to (Fe3O4-gt-PGMA) NPs was thick and loose. The hydrodynamic diameters (Zave) of Fe3O4-gf-PGMA NP clusters could be controlled between 176 to 643 nm, dependent on the PGMA contents and reaction conditions. During SI-ATRP, side reactions happened and caused NP aggregation as well as increase of size of NP clusters. However, the aggregation has been minimized through optimization of reaction conditions. Oppositely, Zave values of Fe3O4-gt-PGMA NPs had little variation of about 120 – 190 nm. And the PGMA content of the Fe3O4-gt-PGMA NPs was limited to 12.5% because of the spatial hindrance during grafting process. The saturation magnetization (Ms) of the unmodified Fe3O4 NPs was about 77 emu/g, while those of the grafting-from and grafting-to Fe3O4-PGMA NPs were 50 – 66 emu/g and 63 – 70 emu/g, respectively. For Fe3O4-PGMA NPs with similar Fe3O4 contents, the grafting-to NPs had slightly higher Ms than the grafting-from counterparts. In addition, the Ms of both kinds of the Fe3O4-PGMA NPs with higher Fe3O4 content (> 87%) were also higher than that of the fluidMAG-Amine, the commercially available amine-modified MNPs. Besides, both kinds of Fe3O4-PGMA NPs also had much higher Fe3O4 contents and Ms values than most of the reported PGMA-modified MNPs. The magnetic epoxy nanocomposites (MENCs) were prepared by blending the modified Fe3O4 NPs into bisphenol A diglycidyl ether (BADGE)-based epoxy system and the distributions of both kinds of the PGMA-modified NPs were much better than that of the oleic acid-modified Fe3O4 NPs. Similar to the NPs, the MENCs also exhibited superparamagnetism. By cross-section TEM observation, the grafting-to Fe3O4-PGMA NPs formed more homogeneous distributions with smaller cluster size than the grafting-from counterparts and gave higher Ms of the MENCs. Nondestructive flaw detection of surface and sub-surface defects could be successfully achieved by brightness contrast of images given through eddy current testing (ET) method, which is firstly reported. The mechanical properties of the materials were influenced very slightly when 2.5% or lower Fe3O4-gt-PGMA NPs were present while the presence of the Fe3O4-gf-PGMA NPs (1 – 2.5 %) gave mild improvement of the storage modulus and increase of the glass-rubber transition temperature(Tg) of the MENCs. Furthermore, the Fe3O4-PGMA NPs could be evenly coated onto the functionalized ultra-high molecular weight poly(ethylene) (UHMWPE) textiles. The Fe3O4-gt-PGMA NPs were coated on the textile in order to prepare NP-coated textile-reinforced composite. Preliminary result of ET measurement showed that the Fe3O4-gt-PGMA NPs coated on the textiles could visualize the structure of the textile hidden inside and their relative depth. Accordingly, the incorporation of MNPs to polymers opens a new pathway of damage-free structural health monitoring of polymeric materials.:1. Introduction 2. Theoretical section 2.1. Magnetite Nanoparticles (MNPs) 2.2. Applications of MNPs 2.3. Atom transfer radical polymerization (ATRP) 2.4. Magnetic nanocomposites (MNCs) 2.5. Damage-free structural health monitoring (SHM) using MNPs 3. Objective of the work 4. Materials, methods and characterization 4.1. Materials 4.2. Methods 4.3. Formation of polymeric magnetic nanocomposites 4.4. Characterization 5. Results and discussions 5.1. Unmodified magnetite nanoparticles (Fe3O4 NPs) 5.2. Oleic acid-modified (Fe3O4–OA) NPs 5.3. PGMA-modified NPs by grafting-from approach (Fe3O4-gf-PGMA NPs) 5.4. PGMA-modified NP by grafting-to approach (Fe3O4-gt-PGMA NPs) 5.5. Comparison between grafting-from and grafting-to Fe3O4-PGMA NPs 5.6. Magnetic epoxy nanocomposites (MENCs) 5.7. Fiber-reinforced epoxy nanocomposites 6. Conclusions and outlook 7. Appendix 8. List of figures, schemes and tables 9. References Versicherung Erklaerung List of publications