Ces travaux de thèse portent sur les phénomènes d’amplification du signal de diffusion Raman par effet de surface et par effet de pointe. Des réseaux de motifs métalliques de taille nanométrique arrangés spatialement ont été fabriqués par la méthode de transfert Langmuir-Blodgett et par lithographie à faisceau d’électrons. De telles structures de géométries contrôlées déposées à la surface de lamelles de microscope ont été développées afin d’amplifier le signal Raman de molécules adsorbées par effet SERS (Surface Enhanced Raman Spectroscopy). Ces nanostructures triangulaires en or de taille proche de la longueur d’onde ont des bandes de résonance plasmon dans le domaine spectral visible. En utilisant une source de laser appropriée dans ce domaine spectral, les facteurs d’amplification Raman d’une couche mono-moléculaire d’un dérivé azobenzène sont de plusieurs ordres de grandeur, et ce pour les deux techniques de nano-lithographie employées. Afin de compléter ces premiers résultats, des réseaux de fils d’or avec de grands facteurs de forme ont été fabriqués. Ces derniers montrent des résonances plasmons multipolaires et des facteurs d’amplification de l’ordre de 105. Les techniques de microscopie en champ proche ont également été développées afin de localiser précisément l’exaltation Raman et d’accroitre la résolution spatiale de mesures Raman. Des pointes métalliques en or de taille nanométrique ont ainsi permis d’amplifier localement le signal de diffusion de molécules placées à leur proximité par effet TERS (Tip Enhanced Raman Spectroscopy). Les développements logiciels et mécaniques entre un microscope confocal Raman et un microscope à force atomique ont été implémentés afin de contrôler simultanément les deux instruments. Ce montage expérimental a été appliqué à l’étude de nanofils semi-conducteurs de nitrure de gallium permettant de suivre leur signal vibrationnel avec une résolution spatiale inférieure à 200 nm. / This thesis work focuses on Raman scattering enhancements by metallic nanostructures. In the first part of this work, arrays of metallic patterns with nanometer dimensions were fabricated by the Langmuir-Blodgett deposition technique and electron-beam lithography. Such structures made of gold were fabricated onto microscope slides with the goal to enhance the Raman signal through SERS effect (Surface Enhanced Raman Spectroscopy). These patterns formed by an assembly of triangular nanostructures with sizes of hundreds of nanometers, exhibit plasmon resonance bands in the visible spectral region. By using an appropriate excitation laser source with respect to the plasmon frequency, Raman enhancement factors of a monolayer were found to be of several order of magnitude for both Langmuir-Blodgett and electron-beam lithography platforms. To further complement these results, gold wires arrays with large aspect ratio made by electron-beam lithography showed multipolar plasmon resonances with enhancement factors up to 105. In the second part of this thesis, near-field Raman microscopy has been developed with the aim to localize precisely the Raman enhancement and improve spatial resolution of Raman measurements. Atomic force microscopy gold tips have been used to locally enhance scattering signal of molecules in close proximity to the tip opening new opportunities. This approach known as TERS (Tip Enhanced Raman Spectroscopy) is of significant interest to probe nanomaterials, nanostructures or monolayers. Software and mechanical developments have been made between a confocal Raman microscope and an atomic force microscope to control simultaneously both instruments. This experimental setup was used to characterize gallium nitride semi-conductors nanowires with spatial resolution better than 200 nm.

No presente trabalho, buscou-se generalizar o Stern-Gerlach óptico para o caso de duas cavidades, as quais possuem eixos ópticos perpendiculares entre si. Nesse experimento, um pacote atomico de dois níveis incide em uma pequena fração do volume ocupado por dois modos, na região onde os nodos das ondas estacionárias de cada modo se superpõem. Diferentemente do Stern-Gerlach óptico de cavidade única, além do intercâmbio de fótons efetuado entre o átomo e cada modo separadamente, também ocorre interação modo-modo, mediada indiretamente pelo átomo. Esse fator contribui efetivamente na caracterização da distribuição de momento do átomo. Espera-se que os desvios de trajetória sofridos pelo átomo, decorrentes de sua interação simultânea com dois modos idênticos do campo de radiação, devam ser observados no plano definido pelas duas cavidades. O estudo é efetuado considerando-se o tratamento clássico da posição do centro de massa atômico, que está associado à sua direção de incidência. Além do que, considera-se a aproximação de Raman-Nath, na qual despreza-se a variação da energia cinética transversal ao movimento atômico, durante a interação átomo-modos. Verifica-se que a análise da distribuição de momento atômico transversal permite acessar a estatística de fótons dos modos das cavidades. Este resultado viabiliza a realização da tomografia dos estados de dois modos por meio da medida da distribuição de momento bidimensional dos átomos. Por fim, através da utilização de estados coerentes na configuração de cavidades cruzadas, investiga-se as possibilidades do controle da direção de deflexão do átomo para aplicações em litografia puramente quântica. / This work deals with the generalization of the optical Stern-Gerlach effect for two cavities whose optical axes are perpendicular to each other. An atomic wave of a two-level atom is focused on a small fraction of the volume occupied by the two modes, in the region where the standing waves nodes overlap. Unlike the optical Stern-Gerlach of single cavity, besides the separate photon exchange between an atom and each mode, there also occurs mode-mode interaction indirectly mediated by the atom. This fact contributes towards the characterization of the atomic momentum distribution. Trajectory deviations suffered by the atom due to its simultaneous interaction with the two identical modes of the radiation field are expected in the plane defined by the two cavities. The study is carried out considering the classical treatment of the atomic center of mass position, which is associated with its incidence direction. The Raman-Nath approximation, which neglects the variation in the kinetic energy transversal to the atomic motion during the interaction atom-modes is considered. The analysis of the transversal momentum distribution of the atom allows accessing the photon statistics of the cavities modes. This result enables the realization of the two-mode states tomography via measurement of the two-dimensional momentum distribution of the atom. Finally, by using coherent states of the crossed cavities configuration, the study investigates the possibilities of controlling the atomic deflection direction for applications to quantum lithography.

Electron Beam Induced Deposition (EBID) is a direct write fabrication process with applications in circuit edit and debug, mask repair, and rapid prototyping. However, it suffers from significant drawbacks, most notably low purity. Work over the last several years has demonstrated that deposition from bulk liquid precursors, rather than organometallic gaseous precursors, results in high purity deposits of low resistivity (LPEBID). In this work, it is shown that the deposits resulting from LP-EBID are only highly conductive when deposited at line doses below 25μC/cm. When the dose exceeds this value, the resulting structure is highly porous providing a poor conductive pathway. It is also shown that beam current has no significant effect on the resistivity of the deposits. Nanowires with resistivity significantly lower than the previous best result of 67μΩ•cm were achieved, with the lowest resistivity being only 6.6μΩ•cm, only a factor of 4 higher than that bulk copper of 1.7μΩ•cm.

Afin de réaliser des dispositifs en polymère à forte valeur ajoutée, l'industrie de la plasturgie s'intéresse depuis quelques années à la convergence possible entre les microtechnologies et les méthodes industrielles de mise en oeuvre des polymères (le thermoformage et la thermo-injection). Dans ce contexte, l'objectif de cette thèse est de démontrer l'intérêt d'une approche à base de microtamponnage pour l'intégration de capteurs à base métallique dans des circuits microfluidiques en thermoplastique réalisés par thermoformage. Pour ces matériaux, cette approche apparait plus pertinente en terme de production de masse qu'une approche de photolithographie classique. Nous avons choisi de démontrer ce concept en étudiant l'intégration d'un capteur de pH et d'un capteur de température dans un système microfluidique en copolymère d'oléfine cyclique (COC) réalisé par thermoformage. En effet, la mesure de ces paramètres physico-chimiques est extrêmement répandue dans différents domaines d'application allant de la chimie à la biologie et à la médecine. Pour le capteur de pH, nous avons développé une couche sensible au pH à base d'oxyde d'iridium (IrOx) électrodéposé sur or. L'influence de différents paramètres (solution d'électrodépôt, méthode d'électrodéposition, nature du substrat métallique et son mode de préparation) sur la réponse au pH de ces couches a été étudiée. Nous avons ainsi pu démonter qu'une approche par microtamponnage passive est adaptée à la préparation de capteurs de pH sur un substrat en COC/Au ayant une sensibilité de -72 mV/pH et une durée de vie de 1 an. Pour le capteur de température, la solution retenue est basée sur le principe d'une thermorésistance. Les capteurs ont été élaborés en utilisant une approche par microtamponnage actif avec croissance d'une couche de nickel (dont l'épaisseur varie entre 0,2 et 5 μm) par métallisation autocatalytique sur polyimide. La dérive des capteurs est actuellement trop importante pour une application pratique. Finalement, des résultats préliminaires d'intégration de ces capteurs dans un microsystème fluidique thermoformé sont présentés avec notamment une configuration originale de mesure différentielle du pH / The plastics industry has been interested for some years in the possible convergence between microtechnologies and conventional polymer manufacturing (hot embossing and injection molding). In this context, this thesis aims at demonstrating the potential of a process based on microcontact printing in order to integrate metal based sensors in thermoplastic microfluidic devices shaped by hot embossing. For the mass production of thermoplastic devices, this approach appears more relevant than conventional photolithography. We chose to demonstrate this concept by investigating the integration of both a pH sensor and a temperature sensor in a thermoformed Cyclo Olefin Copolymer (COC) microfluidic system. Indeed, the measurement of these physicochemical parameters are extremely widespread in different applicative areas ranging from chemistry tobiology and medicine. For the pH sensor, we developed a pH-sensitive layer based on electrodeposited iridium oxide (IrOx) on Au. The influence of various parameters (plating solution and method , nature of the metal substrate and its method of preparation) on the pH response of these layers was studied. We were able to demonstrate that microcontact printing based on a passive approach is suitable for the preparation of pH sensors on a COC substrate with a sensitivity of -72 mV/pH and a 1 year lifetime. As regards the temperature sensor, the solution was to design a thermistor. Sensors were implemented with an approach based on active microcontact printing followed by electroless deposition of nickel (thickness varies between 0,2 and 5 μm) on polyimide. The drift of these sensors is too large for practical application. Finally, preliminary results presenting the integrating of these sensors in a fluidic microsystem are reported using an original configuration based on differential measurement of pH

Heavy Ion Elastic Recoil Detection Analysis (HIERDA) is a versatile Ion Beam Analysis technique well suited to multi-elemental depth profiling of thin layered structures and near-surface regions of materials. An existing limitation is the inability to accurately account for the pronounced broadening and tailing effects of multiple scattering typically seen in HIERDA spectra. This thesis investigates the role of multiple large angle scattering in heavy ion applications such as HIERDA, and seeks to quantify its contribution to experimental output. This is achieved primarily by the development of a computer simulation capable of predicting these contributions and using it to classify and quantify the interactions that cause them. Monte Carlo ion transport simulation is used to generate simulated HIERDA spectra and the results are compared to experimental data acquired using the Time of Flight HIERDA facility at the Australian Nuclear Science and Technology Organisat ion. A Monte Carlo simulation code was adapted to the simulation of HIERDA spectra with considerable attention on improving the modelling efficiency to reduce processing time. Efficiency enhancements have achieved simulation time reductions of two to three orders of magnitude. The simulation is shown to satisfactorily reproduce the complex shape of HIERDA spectra. Some limitations are identified in the ability to accurately predict peak widths and the absolute magnitude of low energy tailing in some cases. The code is used to identify the plural scattering contribution to the spectral features under investigation, and the complexity of plurally scattered ion and recoil paths is demonstrated. The program is also shown to be useful in the interpretation of overlapped energy spectra of elements of similar mass whose signals cannot be reliably separated experimentally. The effect of large angle scattering on the transmission of heavy ions through a nano-scale aperture mask, used to collimate an ion beam to a very small beam spot, is modelled using a version of the program adapted to handle the more complex geometry of the aperture mask. The effectiveness of nano-aperture collimation was studied for a variety of ion-energy combinations. Intensity, energy, and angular distributions of transmitted ions were calculated to quantify the degree to which scattering within the mask limits the spatial resolution achievable. The simulation successfully predicted the effect of misaligning the aperture and the beam, and the result has subsequently been observed experimentally. Transmitted ion distributions showed that the higher energy heavier ions studied are more effectively collimated than are lower energy lighter ions. However, there is still a significant probability of transmission of heavy ions with substantial residual energy beyond the perimeter of the aperture. For the intended application, ion beam lithography, these ions are likely to be problematic. The results indicate that medium energy He ions are the more attractive option, as the residual energy of scattered transmitted ions can be more readily managed by customising the etching process. Continuing research by experimentalists working in this area is proceeding in this direction as a result of the conclusions from this work.

<p>Materials prepared on the nanoscale often exhibit many different properties compared to the same materials in their bulk-state. Interest in nanostructured materials has increased because of these properties in fields such as microelectronics, catalysis, optics and sensors. This increased interest in nanostructured materials calls for new and more precise fabrication techniques.</p><p>This thesis describes how to use the porous anodic aluminium oxide as a template for the fabrication of a variety of nanostructured materials. Palladium and copper nanoparticles were deposited along the pore walls in anodic aluminum oxide using electroless deposition and atomic layer deposition. In both cases, it was possible to control the size of the nanoparticles by carefully monitoring the deposition parameters. The thesis also describes how Prussian blue nanoparticles and nanotubes can be fabricated using the anodic aluminium oxide as a template. The deposition of Prussian blue was performed by a sequential wet-chemical method. By using atomic layer deposition, it was also possible to deposit thin films of amorphous Nb2O5 on the pore walls. When the template was removed by etching, freestanding nanotubes were obtained. The anodic aluminium oxide membrane was also used as a mask for high energy (MeV) ion irradiation of an underlying substrate. The tracks produced were etched away with hydrogen fluoride. In this way, it was possible to transfer the highly ordered porous pattern from the mask onto other oxides such as SiO2 and TiO2.</p><p>All fabricated structures were characterized using a variety of analysis techniques: scanning electron microscopy for evaluating sample morphology; transmission electron microscopy for better resolved investigations of the morphology; X-ray diffraction to assess crystallinity; energy dispersive spectroscopy and X-ray fluorescence spectroscopy to determine the elemental composition and identify possible contaminants.</p><p>The general aim of the work described in this thesis has been to create a set of tools for use in the fabrication of a variety of nanostructured materials, whose dimensions composition can be tailored by selecting appropriate fabrication methods and parameters.</p>

Nanofabrication techniques were used to manufacture nanometer scale protein templates. The fabrication approach employs electron beam lithography (EBL) patterning on poly(ethylene glycol) (PEG) thiol (CH3O(CH2CH2O)17NHCO(CH2)2SH) self-assembled monolayers (SAM) on Au. The PEG SAM prevented protein surface adhesion and binding sites for protein were created in the SAM by EBL. Subsequent to EBL, the patterns in the PEG SAM were backfilled with 40-nm NeutrAvidin-coated fluorescent spheres (FluoSpheres). The spontaneous and directed immobilization of the spheres from a solution to the patterns resulted in high resolution protein patterns. The FluoSpheres could be arranged in any arbitrary pattern with ultimately only one or a few FluoSpheres at each binding site. Growth dynamics and SAM morphology of PEG on Au were studied by atomic force microscopy (AFM). PEG SAMs on three types of Au with different microstructure were examined: thermally evaporated granular Au and two types of Au films produced by hydrogen flame annealing of granular Au, Au(111) and "terraced" Au (crystal orientation unknown). The different Au surfaces' substructure affected the morphology and mechanical properties of the PEG SAM. On Au(111), AFM imaging revealed monolayer formation through three distinct steps: island nucleation, island growth, and coalescence. The fine-structure of the SAM revealed dendritic island formation - an observation which can be explained by attractive intermolecular interactions and diffusion-limited aggregation. Island growth was not observed on the "terraced" Au. AFM studies of EBL patterned PEG SAMs on Au(111) revealed two different patterning mechanisms. At low doses, the pattern formation occurs by SAM ablation in a self-developing process where the feature depth is directly dose dependent. At higher doses electron beam induced deposition of material, so-called contamination writing, is seen in the ablated areas of the SAM. The balance between these two mechanisms is shown to depend on the geometry of the pattern. In addition to PEG SAMs, fibronectin monolayers on SiO2 surfaces were patterned by EBL. The areas exposed with EBL lose their functionality and do not bind anti-fibronectin. With this approach we constructed fibronectin templates and used them for cell studies demonstrating pattern dependent cell geometries and cell adhesion. / QC 20101008

Materials prepared on the nanoscale often exhibit many different properties compared to the same materials in their bulk-state. Interest in nanostructured materials has increased because of these properties in fields such as microelectronics, catalysis, optics and sensors. This increased interest in nanostructured materials calls for new and more precise fabrication techniques. This thesis describes how to use the porous anodic aluminium oxide as a template for the fabrication of a variety of nanostructured materials. Palladium and copper nanoparticles were deposited along the pore walls in anodic aluminum oxide using electroless deposition and atomic layer deposition. In both cases, it was possible to control the size of the nanoparticles by carefully monitoring the deposition parameters. The thesis also describes how Prussian blue nanoparticles and nanotubes can be fabricated using the anodic aluminium oxide as a template. The deposition of Prussian blue was performed by a sequential wet-chemical method. By using atomic layer deposition, it was also possible to deposit thin films of amorphous Nb2O5 on the pore walls. When the template was removed by etching, freestanding nanotubes were obtained. The anodic aluminium oxide membrane was also used as a mask for high energy (MeV) ion irradiation of an underlying substrate. The tracks produced were etched away with hydrogen fluoride. In this way, it was possible to transfer the highly ordered porous pattern from the mask onto other oxides such as SiO2 and TiO2. All fabricated structures were characterized using a variety of analysis techniques: scanning electron microscopy for evaluating sample morphology; transmission electron microscopy for better resolved investigations of the morphology; X-ray diffraction to assess crystallinity; energy dispersive spectroscopy and X-ray fluorescence spectroscopy to determine the elemental composition and identify possible contaminants. The general aim of the work described in this thesis has been to create a set of tools for use in the fabrication of a variety of nanostructured materials, whose dimensions composition can be tailored by selecting appropriate fabrication methods and parameters.

The steady and aggressive downscaling of the physical dimensions of the conventional metal-oxide-semiconductor field-effect-transistor (MOSFET) has been the main driving force for the IC industry and information technology over the past decades. As the device dimensions approach the fundamental limits, novel double/trigate device architecture such as FinFET is needed to guarantee the ultimate downscaling. Furthermore, Schottky barrier source/drain technology presents a promising solution to reducing the parasitic source/drain resistance in the FinFET. The ultimate goal of this thesis is to integrate Schottky barrier source/drain in FinFETs, with an emphasis on process development and integration towards competitive devices. First, a robust sidewall transfer lithography (STL) technology is developed for mass fabrication of Si-nanowires in a controllable manner. A scalable self-aligned silicide (SALICIDE) process for Pt-silicides is also developed. Directly accessible and uniform NWs of Ni- and Pt-silicides are routinely fabricated by combining STL and SALICIDE. The silicide NWs are characterized by resistivity values comparable to those of their thin–film counterparts. Second, a systematic experimental study is performed for dopant segregation (DS) at the PtSi/Si and NiSi/Si interfaces in order to modulate the effective SBHs needed for competitive FinFETs. Two complementary schemes SIDS (silicidation induced dopant segregation) and SADS (silicide as diffusion source) are compared, and both yield substantial SBH modifications for both polarities of Schottky diodes (i.e. φbn and φbp). Third, Schottky barrier source/drain MOSFETs are fabricated in UTB-SOI. With PtSi that is usually used as the Schottky barrier source/drain for p-channel SB-MOSFETs, DS with appropriate dopants leads to excellent performance for both types of SBMOSFETs. However, a large variation in position of the PtSi/Si interface with reference to the gate edge (i.e., underlap) along the gate width is evidenced by TEM. Finally, integration of PtSi NWs in FinFETs is carried out by combining the STL technology, the Pt-SALICIDE process and the DS technology, all developed during the course of this thesis work. The performance of the p-channel FinFETs is improved by DS with B, confirming the SB-FinFET concept despite device performance fluctuations mostly likely due to the presence of the PtSi-to-gate underlap. / QC 20100923

The efficiency of an organic photovoltaic cell depends mainly on its morphology where an exciton has to migrate to a p-n junction to create a photocurrent. Therefore the distance from the bulk of the cell to a junction interface should not exceed the diffusion length of the exciton. In this thesis, two novel lithographical methods, to produce specific polymer morphologies, were developed and evaluated. In the first method, called embedded annealing, self-assembled polystyrene colloids were embedded in a polydimethylsiloxane (PDMS) film and annealed under an electric field to produce a bi-polymer structure consisting of polymer columns in a thin film of PDMS. Polymer colloids were successfully assembled into two dimensional hexagonally close packed arrays. However, the annealing process was unsuccessful. The second method, imprint annealing, aimed to increase the aspect ratio (height/width) of thermally imprinted micrometer sized polystyrene features by annealing them in uniform electric fields. The results showed that the aspect ratio of imprinted features can be significantly increased, 21-fold, while maintaining the periodicity of the original imprint. This is in contrast to previous results where smooth polymer films annealed in uniform fields where the periodicity of the resulting structures cannot be independently controlled, and are highly sensitive to the electrode spacing. Feature sizes down to 1 µm and aspect ratios up to 4.5 were achieved using imprint annealing. / Verkningsgraden hos en hos en solcell beror, för givna material, framförallt på dess uppbyggnad. För att bidra till fotoströmmen måste en genererad exciton vandra till en pn-övergång. På grund av detta bör det längsta avståndet till närmaste pn-övergång i solcellen inte vara längre än excitonens diffusionslängd. I detta examensarbete testas två olika litografiska metoder för att åstadkomma en specifik filmgeometri lämpad för organiska solceller. Den första metoden, kallad embedded annealing, går ut på att bädda in spontant ordnade sfäriska polystyrenkolloider i en polydimetylsiloxan (PDMS) -film för att sedan vid förhöjd temperatur applicera ett elektiskt fält över filmen. Förhoppningen var att på detta sätt töja ut kolloiderna till pelare genom PDMS-filmen. I det första steget ordnades kolloiderna sponant i tätpackade hexagonala tvådimensionella gitter på kiselsubstrat. Experimenten lyckades inte med hjälp av elektriska fält töja ut kolloiderna. Den andra metoden, imprint annealing, syftar till att öka höjd/bredd -förhållandet och minska diametern hos präglade polystyrenstrukturer. Dessa ursprungliga topografiska stukturer skapas med hjälp av en tryckpressmetod kallad nanoimprinting. Dessa strukturer värmdes upp, och ett uniformt elekrisk fält applicerades över dem. Mina resultat visar att man med elektriska fält avsevärt kan öka höjd-breddförhållandet hos polymerstrukturer och samtidigt bevara periodiciteten hos de ursprungliga strukturerna. Detta står i kontrast mot tidigare resultat på släta filmer, där periodiciteten inte kan kontrolleras oberonde av andra parametrar. Med imprint annealing ökades höjd-breddförhållandet hos enskilda strukturer upp till 21 gånger. Diametrar ner till 1 µm och höjd/breddförhållanden upp till 4,5 uppnåddes.