Ce travail de thèse a concerné l'étude du comportement de nanoparticules d'électrocatalyseurs à base de Pt et Co déposées sur carbone de grande aire développée (Pt/C, PtCo/C et Pt3Co/C) en conditions représentative d'un fonctionnement à la cathode d'une pile à combustible à membrane échangeuse de protons. Dans une première phase, des électrodes modèles de ces matériaux ont été préparées sur des embouts de carbone vitreux compatibles avec une utilisation en montage d'électrode à disque tournant en milieu acide sulfurique, pour étudier l'évolution des performances électrochimiques (adsorption/désorption de l'hydrogène, Hupd, électrooxydation d'une monocouche de CO adsorbée à la surface du catalyseur : " CO-stripping ", cinétique d'électroréduction de l'oxygène) après cyclage accéléré de potentiel (0,1 à 0,9 V vs. RHE et 0,6 à 0,9 V vs. RHE par créneaux d'une minute à chaque potentiel). Ces mesures électrochimiques ont été complétées par des observations statistiques par microscopie électronique en transmission (TEM) et fluorescence X (X-EDS) avant/après ces vieillissements sur des prélèvements représentatifs des couches actives. Les résultats montrent que le cobalt est irréversiblement oxydé/dissous des alliages Pt-Co et que la maturation d'Ostwald advient (pour le Pt) spécialement lorsque la borne inférieure de potentiel est fixée à 0,1 V vs. RHE. Ces mesures statistiques ont été confirmées par des expériences de MET en localisation identique (ILTEM), dans lesquelles les mêmes nanoparticules sont physiquement observées avant/après électrochimie réalisée sur la grille de microscopie[1]. Dans un second temps, des vieillissements identiques ont été mis en œuvre sur les mêmes matériaux électrocatalytiques en électrolyte polymère (Nafion), plus représentatif des conditions PEMFC, par utilisation d'une ultramicroélectrode à cavité et d'une " cellule sèche " dans laquelle le seul électrolyte est le Nafion (il n'y a donc pas d'électrolyte liquide). Dans ces conditions, plus proches des conditions réelles de fonctionnement d'une PEMFC, les mécanismes de dégradations sont différents de ceux observés en présence (d'excès) d'électrolyte liquide, parce que (entre autre), les ions Pt2+ formés à haut potentiel sont piégés dans le ionomère et donc plus faciles à redéposer sur les nanoparticules restantes. Le changement de morphologie (et composition) des nanoparticules de Pt/C (et Pt-Co/C) n'est donc pas identique en milieu H2SO4 et en milieu Nafion, ce qui montre que les tests réalisés en condition de laboratoire (en électrolyte liquide) ne sont pas forcément représentatifs de ce qui advient en PEMFC. Par extension, cette cellule sèche a été mise en œuvre pour mesurer les propriétés électrocatalytiques des différents électrocatalyseurs et, une fois encore, le milieu électrolyte liquide ne rend pas compte des performances observées en milieu " polymère ". Ces mesures ont été complétées par des observations statistiques en MET. Enfin, et il s'agit d'une innovation conséquente propre à ce travail, la méthode ILTEM a été employée pour des grilles de microscopie (supportant les électrocatalyseurs) n'ayant été utilisées qu'en interface avec un électrolyte polymère. Cela a permis de confirmer de manière quantitative et sur les mêmes grains de carbone / nanoparticules de Pt (ou Pt-Co) que les dégradations observées en milieu électrolyte liquide ne rendent pas compte de celles advenant en milieu polymère, la présence d'eau liquide jouant un rôle déterminant dans le premier cas (dissolution des espèces Pt2+/Co2+, oxydation du carbone, etc.).

Le dihydrogène (H2) se présente comme le futur vecteur énergétique pour une économie basée sur des ressources propres et respectueuses de l'environnement. Il est le combustible idéal de la pile à combustible régénérative constituée de deux entités : un électrolyseur pour sa production, et une pile à combustible pour sa conversion directe en énergie électrique. Ce système présente l'avantage d'être compact et autonome. Cependant, l'amélioration de l'activité catalytique des matériaux, leur stabilité et l'élimination de métaux nobles dans leur composition sont nécessaires. Des catalyseurs bifonctionnels à base de métaux de transition associés au graphène ont alors été synthétisés. L'interaction oxyde-graphène a été étudiée sur un catalyseur Co3O4/NRGO. À faible teneur en cobalt, l'interaction entre les atomes de cobalt de l'oxyde et les atomes d'azote greffés sur les plans de graphène a été observée par voltammétrie cyclique. Cette interaction est responsable d'une diminution de la taille des nanoparticules de cobaltite et de l'activité de celles-ci vis-à-vis de la réaction de réduction du dioxygène (RRO). La substitution du cobalt par le nickel dans des structures de type spinelle (NiCo2O4/RGO) obtenu par voie solvothermale, a permis d'améliorer les performances électrocatalytiques vis-à-vis de la RRO et de la RDO. Ce matériau et un autre de type Fe-N-C préparé en collaboration avec un laboratoire de l'Université Technique de Berlin ont servi de cathode dans des études préliminaires réalisées en configuration pile à combustible alcaline à membrane échangeuse d'anion (SAFC). / Hydrogen, as an environmentally friendly future energy vector, is a non-toxic and convenient molecule for regenerative fuel cell, which connects two different technologies: an electrolyzer for H2 production, and a fuel cell for its direct conversion to electric energy. This kind of system possesses many advantages, such as lightness, compactness and more autonomy. However, improvement of activity and durability of electrode materials free from noble metals in their composition is needed. Thereby, bifunctional catalysts composed of transition metals deposited onto graphene-based materials were synthesized. The interaction between the metal atom of the oxide and the graphene doped heteroatom in the Co3O4/NRGO catalyst was investigated physicochemically. With a low cobalt loading, the interaction between cobalt and nitrogen was characterized by cyclic voltammetry, which revealed that it was responsible for decreasing the oxide nanoparticle size, as well as increasing the material activity towards the oxygen reduction reaction (ORR). The substitution of Co by Ni in the spinel structure (NiCo2O4/RGO) obtained by solvothermal synthesis, allowed the enhancement of the electrocatalytic performances towards the ORR and OER. Moreover, this catalyst as well as another material prepared in collaborative program with a lab from Technical University of Berlin were used as cathode in preliminary studies undertaken on solid alkaline fuel cell (SAFC).

Les couches catalytiques avec une structure ordonnée à base de nanoparticules de Pt supportées sur des nanofilaments de carbone verticalement alignés ont montré des performances intéressantes grâce à l’amélioration des propriétés du transport de matière et à une meilleure utilisation du Pt. Des études électrochimiques combinées à une modélisation mathématique ont mis en évidence l’influence du transport de protons sur les processus d’oxydo-réduction, la cinétique et le mécanisme de réduction de l’O2 (ORR), et sur H2O2 qui s’échappe des couches pendant l’ORR. Nous avons montré que (i) les protons sont impliqués dans l’étape limitante de la réaction, (ii) pour un pH ≥ 3, un plateau de courant limité par la diffusion des protons est observé et, (iii) pour un pH ≥ 3, le mécanisme de l’ORR implique non seulement les ions hydroniums mais aussi les molécules d’eau. L’intégration de ces couches catalytiques dans des PEMFCs haute température a ensuite été étudiée. Les performances obtenues sont légèrement plus basses que celles des couches conventionnelles. Un travail d’optimisation reste donc à accomplir pour améliorer les performances. / Ordered catalytic layers based on vertically aligned carbon nanofilaments with Pt nanoparticles demonstrate high efficiency for oxygen transport and Pt utilization in the catalytic layer. Electrochemical studies combined with mathematical modeling confirm the influence of the proton transport on surface red-ox processes, the kinetics and the mechanism of the O2 reduction (ORR), and on the H2O2 escape. We show that (i) protons are involved in the rate-determining step of the O2 reduction, (ii) for pH ≥ 3, a plateau corresponding to the diffusion-limited current of protons is observed and, (iii) for pH ≥ 3, the mechanism of the ORR involves not only the hydronium ions but also water molecules. The integration of these catalytic layers in high temperature PEMFCs was then studied. The performance is slightly lower than that for conventional layers. An optimization work is required to improve the performance.

In recent years, there has been an increasing interest on renewable energy sources as substitute to fossil fuels. Among various processes of energy generation, electrochemical methods such as storage and conversion systems, electrolysis of water (production of H2 and O2), fuel cells, batteries, supercapacitors and solar cells have received great attention. The core of these energy technologies is a series of electrochemical processes, which directly depend on the nature of ‘electro catalyst’. The design and preparation of an electro catalyst is based on new concepts such as controlled surface roughness, atomic topographic profiles, defined catalytic sites, atomic rearrangements, and phase transitions during electrochemical reactions. Good electro catalysts should possess low over potential, high exchange current density, high stability, low cost and high abundance. The most fundamental reactions in the area of electrochemistry are hydrogen evolution (HER) and oxygen reduction (ORR) reactions. They are important in different energy systems such as fuel cells and batteries. Platinum has been a favoured electro catalyst due to its high activity, favourable density of states at Fermi level and chemical inertness. The low abundance, however, limits its large scale applications. Alternate materials with high catalytic activities are always required. In this particular direction, metal chalcogenides such as sulphides and selenides have attracted attention in recent years. The present thesis describes the synthesis of different phases of palladium and nickel chalcogenides and their applicability in various electrochemical reactions, both in aqueous and organic media. First part includes the synthesis of highly crystalline palladium selenide phases namely Pd17Se15, Pd7Se4 and Pd4Se by employing facile single source molecular precursor method. Pure palladium selenide phases are prepared by thrombolysis of highly processable intermediate complexes formed from metal and selenium precursors. Continuous films of different dimensions on various substrates (glass, ITO, FTO etc.) could be prepared (figure 1). This is one of the requirements for processing any new material. Thickness of the films could be altered by changing the volume of precursor complex coated on the substrate. All the phases are found to be metallic in nature with resistivity values in the range of 30 to 180 µΩ.cm. Figure 1. (a) Scanning electron micrograph and (b) photographic image of Pd17Se15 prepared on different substrates glass (1), Si (2), fluorine doped tin oxide (FTO) (3) and DSSC solar cell fabricated using FTO coated Pd17Se15 as the counter electrode (4). Other components of DSSC are given in the experimental section. All the palladium selenides phases are shown to be catalytically active towards electrochemical reactions such as HER and ORR. It is observed that the activities of the phases depend on the stoichiometric ratio of palladium to selenium. Higher the palladium content in the phase, higher is the catalytic activity observed. Therefore, the activities of the chalcogenides can be easily tuned by varying the ratio of metal to chalcogen. Tafel slopes of 50–60 mV/decade are observed for all three phases towards HER indicating that Volmer- Heyrovsky mechanism is operative. The exchange current densities are in the range of 2.3 x 10-4 A cm-2 to 6.6 x 10-6 A cm-2 (figure 2a). Figure 2. (a) Linear sweep voltammograms of Pd17Se15, Pd7Se4 and Pd4Se in 0.5 M H2SO4 (HER) and (b) 0.1 M KOH (ORR) at a scan rate of 2 mVs-1. These phases are found to be highly robust and stable under different pH conditions. Stability of the phases is confirmed by characterizing the catalysts post-HER process, using various techniques such as XPS, XRD and SEM. High activities observed for Pd4Se is explained based on electrochemically active surface area values determined from under potential deposition studies and also based on DFT calculations. Computational studies reveal the presence of different charge distribution on palladium in all the three phases which is likely to be another reason for varied activities. Palladium selenides are also explored as catalysts towards ORR in alkaline medium. Kinetic parameters and reaction mechanism are determined using RDE studies. All the three phases are found to be active and Pd4Se shows the highest activity, following a direct 4 electron reduction pathway (figure 2b). Other two phases follow 2 electron pathway terminating at hydrogen peroxide stage. Catalytic activity of Pd17Se15 is further improved by Nano structuring of the material and by synthesizing the material on active supports such as rGO, acetylene black and today carbon. ORR plays an important role in metal-air batteries. The palladium chalcogenides are used as electrodes in metal-air batteries. Specific energy density observed in the case of Mg-air primary batteries is higher for Pd4Se than the other two phases (figure 3a). Figure 3. (a) Discharge curves of Mg-O2 battery with different phases of palladium selenides as cathodes. Constant current density of 0.5 mA cm-2 is used for discharge. (b) Characteristic J–V curves of DSSCs with Pd17Se15, Pd7Se4 and Pt as counter electrodes. Versatility of these phases is further studied towards redox reaction in non-aqueous medium (I3-/I-). This reaction plays a crucial role in the regeneration of the dye in dye-sensitized solar cells (DSSC). Palladium selenide phases prepared on FTO plates are employed as counter electrodes in DSSC. The solar light conversion efficiencies are found to be 7.45 and 6.8% for Pd17Se15 and Pd7Se4 respectively and are comparable to that of platinum (figure 3b). The reason for high activities may be attributed to high electronic conductivity and low work function of the phases. The following chapter deals with the synthesis of palladium sulphide phases (Pd4S and Pd16S7) using both hydrothermal and single source precursor methods. Electro catalytic activities of the phases are shown towards HER and ORR and Pd4S exhibits better catalytic activities than that of Pd16S7 phase. Direct electrochemistry of cytochrome c is achieved on Pd4S with ∆E of ~64 mV (figure 4a). Electrochemical oxidation of ethanol, ethylene glycol (EG) and glycerol are also studied on the Pd4S phase and the activity is found to follow the order, glycerol > ethylene glycol > ethanol (figure 4b). Figure 4. (a) Cyclic voltammograms of Pd4S in (1) 0.1 M phosphate buffer solution (pH 7.0) and (2) in presence of 0.2 mM cytochrome c at a scan rate of 50 mVs-1 and (b) Voltammograms of Pd4S in presence of different alcohols (ethanol, EG and glycerol) in 1 M KOH solution at sweep rate of 50 mVs-1. Concentration of alcohols used is 0.1 M. The effect of dimensionality on the electro catalytic activity of nickel selenide phases forms part of the next chapter. Nickel selenide (NiSe) nanostructures possessing different morphologies of wires, spheres and hexagons are synthesized by varying the selenium precursors namely, selenourea, selenium dioxide (SeO2) and potassium selenocyanate (KSeCN), respectively using hydrothermal method. The different selenium precursors result in morphologies that are probably dictated by the by-products as well as relative rates of amorphous selenium formation and dissolution. The three different morphologies are used as catalysts for HER, ORR and glucose oxidation reactions. The wire morphology is found to be better than that of spheres and hexagons for all the reactions. Among the reactions studied, NiSe is found to be good for HER and glucose oxidation while ORR seems to terminate at the peroxide stage. In alkaline medium, nickel forms hydroxides and oxy-hydroxides and these oxyhydroxides are catalytically active towards the oxidation of glucose. Therefore, nickel selenides are employed as highly selective non-enzymatic glucose sensors and detection limit of 5 µM is observed. Electrical measurements on a single nanowire and a hexagon morphology of NiSe are carried out on devices fabricated by focused ion beam (FIB) technique (figure 5). The semiconducting nature of NiSe is revealed in the I-v measurements. The band gap of the material is found to be 1.9 eV and hence the single nanowire and hexagon are shown to act as visible light photodetector. Figure 5. SEM images of (a) single NiSe nanowire and (b) single NiSe hexagon with Pt contacts fabricated by FIB technique. Figure 6. Cyclic voltammograms of NiSe nanowires in 0.5 M aqueous NaOH in the (i) absence and (ii) the presence of 0.5 mM glucose, at a scan rate of 20 mVs-1 and (b) Galvanostatic discharge performance of Ni3Se2 with different morphologies (A, B and C represent Ni3Se2 prepared from SeO2, selenourea and KSeCN respectively). The next chapter includes the synthesis of different morphologies of Ni3Se2 using three different selenium precursors (SeO2, KSeCN and selenourea) and the study of their activities towards electrochemical reactions such as HER and glucose oxidation (figure 6a). Electrical measurements demonstrated the metallic behaviour of the material. These are also shown to be efficient electrode materials in energy storage devices such as supercapacitors with high specific capacitance of 2200 F/g (figure 6b). The studies are summarized in the last chapter with scope for further work. The appendixes show preliminary studies on electrooxidation of glycerol and propanol on Pd supported on TiN, synthesis of other selenides of Ni, Cu, Ag and Ti, and electro synthesis of metal-organic frameworks. (For figures pl refer the abstract pdf file)

Am Beispiel verschiedener Strömungstypen wird die Stabilität von Strömungen unter Einfluß eines Temperaturfeldes untersucht. Eine reguläre Störungs- rechnung wird durchgeführt, um die Effekte temperatur- abhängiger Stoffwerte systematisch und allgemein- gültig erfassen zu können. Die Ergebnisse werden in Form asymptotischer Reihen für die kritischen Kenn- zahlen der jeweiligen Probleme angegeben. Sowohl die Orr-Sommerfeld-Gleichungen als auch die PSE-Gleichungen, jeweils mit variablen Stoffwerten, kommen bei der Untersuchung von Grenzschicht- strömungen zum Einsatz. Von besonderem Interesse sind hier die Unterschiede in den Lösungen beider mathematischer Modelle bezüglich der Effekte variabler Stoffwerte. Es zeigt sich, dass die Differenzen in den Lösungen beider Theorien für den Fall konstanter und für den Fall variabler Stoffwerte gleich groß sind. Für die Grenzschichtströmung bei natürlicher Kon- vektion an einer beheizten vertikalen Wand werden die vollständigen PSE-Gleichungen gelöst. Hier zeigen sich starke Abweichungen zur lokalen paral- lelen Theorie (Orr--Sommerfeld--Gleichungen).

En la presente tesis doctoral se realiza un estudio detallado sobre el mecanismo de la reacción de reducción de oxígeno (ORR) en electrodos monocristalinos de platino. Para ello, se han realizado medidas electroquímicas usando la configuración de electrodo rotatorio de menisco colgante (HMRDE) con superficies con distinta estructura superficial y variando condiciones de la disolución de trabajo como el pH, fuerza iónica o la ausencia o presencia de bromuros. La conclusión principal que se extra de estos experimentos es la posibilidad de la existencia de un punto de bifurcación en el mecanismo, implicando el intermedio OOH, antes de la formación de peróxido de hidrógeno. Además, también se estudia la ORR y la reacción de oxidación de ácido fórmico en electrodos monocristalinos de Pt en presencia de acetonitrilo, como estudio previo al estudio de estas reacciones en disolventes orgánicos con pequeñas cantidades de agua. Por último, se estudia la ORR en un Aza-CMP, lo cual permite obtener información fundamental que se puede aplicar en estudios sobre el mecanismo de la ORR en los sitios activos de materiales de carbón funcionalizados con nitrógeno.

The pressure on clean and sustainable energy supplies is increasing. In this regard energy conversion by electrochemical processes plays a major role, for both fuel cell reactions and electrolysis reactions. The sulphur dioxide oxidation reaction (SOR) is a common reaction found in the Hybrid Sulphur Cycle (HyS) and the HyS is a way to produce large-scale hydrogen (H2). The problem with the use of the HyS and fuel cells is the cost involved as large amounts of Pt are required for effective operation. The aim of the study was to determine whether there was an alternative catalyst which was more efficient and cost-effective than Pt. The oxygen reduction reaction (ORR), the ethanol oxidation reaction (EOR) and SOR were studied by means of different electrochemical techniques (cyclovoltammetry (CV), linear polarization (LP) and rotating disk electrode (RDE)) on polycrystalline platinum (Pt) and palladium (Pd). The SRR and EOR are common reactions occurring at the cathode and anode, respectively, in fuel cells and these reactions have been investigated extensively. The reason for studying the reactions was as a preparation for the SOR. This study compared polycrystalline Pt and Pd for the different reactions, with the main focus on the SOR as Pd is considerably cheaper than Pt, and for the SOR polycrystalline Pd has by no means been investigated intensively. Polycrystalline Pt and Pd were compared by different electrochemical techniques and analyses. The Koutecky-Levich and Levich analyses were used to (i) calculate the number of e- involved in the relevant reaction, (ii) to determine whether the reaction was mass transfer controlled at high overpotentials and (iii) whether the reaction mechanism changed with potential. Next the kinetic current density ( k) was calculated from Koutecky-Levich analyses, which was further used for Tafel slope analyses. If it was not possible to carry out the analyses, the activation energy (Ea) was used to determine the electrocatalytic activity of the catalyst. The electrocatalytic activity was also determined by comparing onset potentials (Es), peak potentials (Ep) and limited/maximum current density ( b/ p) of each catalyst. This study was only a preliminary study for the SOR and therefore, further studies are certainly required. It seemed Pd shows better electrocatalytic activity than Pt for the SRR in an alkaline electrolyte because of similar Es, but Pd produced a higher cathodic current density. Pt showed a lower Es than Pd for the SRR in an acid electrolyte, but Pd delivered a higher cathodic current density. This, therefore, means that the SRR in an acid electrolyte is kinetically more favourable on Pd than on Pt. For the EOR better electrocatalytic activity was obtained with Pd than with Pt in an alkaline electrolyte due to higher current densities at lower potentials and Pd showed lower Ea values than Pt in the potential range normally used for fuel cells. Pd was inactive for EOR in an acid electrolyte, while a reaction occurred on Pt. A possible reason for this observation may be due to the H2 absorbing strongly on Pd thus blocking the active positions on the electrode surfaces, preventing further reaction. Pd showed higher electrocatalytic activity for the SOR due to lower Es and higher current densities at low potentials. From the RDE studies it was established that the SRR in an alkaline electrolyte on polycrystalline Pt and Pd was mass transfer controlled at low potentials (high overpotentials), but the SRR in an acid electrolyte was only mass transfer controlled on Pt. The SOR was not mass transfer controlled on polycrystalline Pt and Pd at high potentials (high overpotentials). These assumptions were confirmed by Levich analysis. Using Koutecky-Levich analysis, it was determined that the reaction mechanism on polycrystalline Pt and Pd changed with potential for SRR in an alkaline electrolyte and the SOR. For the SRR in an acid electrolyte the reaction mechanism remained constant with changes in potential on polycrystalline Pd, but the reaction mechanism on polycrystalline Pt changed with potential. These assumptions were confirmed by the number of e-, calculated using Koutecky-Levich analyses. Levich and Koutecky-Levich analyses were not performed for EOR as an increase in rotation speed did not produce an increase in current density. Tafel slope analyses were conducted by making use of overpotentials and k, where possible. As in the case of ethanol, it was not possible to execute Koutecky-Levich analyses and, therefore, it was not possible to perform Tafel slope analyses using k. Tafel slope analyses for the EOR was therefore performed with normal current densities at 0 rotations per minute (rpm). The reaction mechanisms on Pt and Pd for the SRR in alkaline and acidic electrolytes differed due to different Tafel slopes. Pt and Pd displayed similar Tafel slopes for the EOR in alkaline electrolyte, thus suggesting that the reaction mechanisms on Pt and Pd were the same. For the SOR it seemed that the reaction mechanism on Pt and Pd were similar because of similar Tafel slopes. This was only a preliminary and comparative study for polycrystalline Pt and Pd, and the reaction mechanism was not further studied by means of spectroscopic techniques. / MSc (Chemistry), North-West University, Potchefstroom Campus, 2014

The pressure on clean and sustainable energy supplies is increasing. In this regard energy conversion by electrochemical processes plays a major role, for both fuel cell reactions and electrolysis reactions. The sulphur dioxide oxidation reaction (SOR) is a common reaction found in the Hybrid Sulphur Cycle (HyS) and the HyS is a way to produce large-scale hydrogen (H2). The problem with the use of the HyS and fuel cells is the cost involved as large amounts of Pt are required for effective operation. The aim of the study was to determine whether there was an alternative catalyst which was more efficient and cost-effective than Pt. The oxygen reduction reaction (ORR), the ethanol oxidation reaction (EOR) and SOR were studied by means of different electrochemical techniques (cyclovoltammetry (CV), linear polarization (LP) and rotating disk electrode (RDE)) on polycrystalline platinum (Pt) and palladium (Pd). The SRR and EOR are common reactions occurring at the cathode and anode, respectively, in fuel cells and these reactions have been investigated extensively. The reason for studying the reactions was as a preparation for the SOR. This study compared polycrystalline Pt and Pd for the different reactions, with the main focus on the SOR as Pd is considerably cheaper than Pt, and for the SOR polycrystalline Pd has by no means been investigated intensively. Polycrystalline Pt and Pd were compared by different electrochemical techniques and analyses. The Koutecky-Levich and Levich analyses were used to (i) calculate the number of e- involved in the relevant reaction, (ii) to determine whether the reaction was mass transfer controlled at high overpotentials and (iii) whether the reaction mechanism changed with potential. Next the kinetic current density ( k) was calculated from Koutecky-Levich analyses, which was further used for Tafel slope analyses. If it was not possible to carry out the analyses, the activation energy (Ea) was used to determine the electrocatalytic activity of the catalyst. The electrocatalytic activity was also determined by comparing onset potentials (Es), peak potentials (Ep) and limited/maximum current density ( b/ p) of each catalyst. This study was only a preliminary study for the SOR and therefore, further studies are certainly required. It seemed Pd shows better electrocatalytic activity than Pt for the SRR in an alkaline electrolyte because of similar Es, but Pd produced a higher cathodic current density. Pt showed a lower Es than Pd for the SRR in an acid electrolyte, but Pd delivered a higher cathodic current density. This, therefore, means that the SRR in an acid electrolyte is kinetically more favourable on Pd than on Pt. For the EOR better electrocatalytic activity was obtained with Pd than with Pt in an alkaline electrolyte due to higher current densities at lower potentials and Pd showed lower Ea values than Pt in the potential range normally used for fuel cells. Pd was inactive for EOR in an acid electrolyte, while a reaction occurred on Pt. A possible reason for this observation may be due to the H2 absorbing strongly on Pd thus blocking the active positions on the electrode surfaces, preventing further reaction. Pd showed higher electrocatalytic activity for the SOR due to lower Es and higher current densities at low potentials. From the RDE studies it was established that the SRR in an alkaline electrolyte on polycrystalline Pt and Pd was mass transfer controlled at low potentials (high overpotentials), but the SRR in an acid electrolyte was only mass transfer controlled on Pt. The SOR was not mass transfer controlled on polycrystalline Pt and Pd at high potentials (high overpotentials). These assumptions were confirmed by Levich analysis. Using Koutecky-Levich analysis, it was determined that the reaction mechanism on polycrystalline Pt and Pd changed with potential for SRR in an alkaline electrolyte and the SOR. For the SRR in an acid electrolyte the reaction mechanism remained constant with changes in potential on polycrystalline Pd, but the reaction mechanism on polycrystalline Pt changed with potential. These assumptions were confirmed by the number of e-, calculated using Koutecky-Levich analyses. Levich and Koutecky-Levich analyses were not performed for EOR as an increase in rotation speed did not produce an increase in current density. Tafel slope analyses were conducted by making use of overpotentials and k, where possible. As in the case of ethanol, it was not possible to execute Koutecky-Levich analyses and, therefore, it was not possible to perform Tafel slope analyses using k. Tafel slope analyses for the EOR was therefore performed with normal current densities at 0 rotations per minute (rpm). The reaction mechanisms on Pt and Pd for the SRR in alkaline and acidic electrolytes differed due to different Tafel slopes. Pt and Pd displayed similar Tafel slopes for the EOR in alkaline electrolyte, thus suggesting that the reaction mechanisms on Pt and Pd were the same. For the SOR it seemed that the reaction mechanism on Pt and Pd were similar because of similar Tafel slopes. This was only a preliminary and comparative study for polycrystalline Pt and Pd, and the reaction mechanism was not further studied by means of spectroscopic techniques. / MSc (Chemistry), North-West University, Potchefstroom Campus, 2014