Doctor of Philosophy / The kinetics of electrosterically stabilized emulsion systems was studied. The aim of this was to understand the impact that steric and electrosteric stabilizers have on the kinetics of particle growth and particle formation in the area of emulsion polymerization. The well-established mechanisms that govern these processes for emulsions stabilized by conventional low molecular weight surfactants were used as a reference point for comparative purposes. Model latexes were synthesized that comprised of a poly(styrene) core stabilized by a corona of poly(acrylic acid). The advent of successful controlled radical polymerization techniques in heterogeneous media (via RAFT polymerization) allowed for latexes to be synthesized under molecular weight control. For the first time, the degree of polymerization of the stabilizing block on the particle surface was able to be controlled and verified experimentally using mass spectrometry techniques. Three latexes were made with different average degrees of polymerization of the stabilizing block; five, ten and twenty monomer units respectively. A methodology was developed to remove the RAFT functionality from the polymer chains present in the emulsion while retaining the desired particle morphology. Oxidation with tertbutylhydroperoxide (TBHP) was proven to be successful at eliminating the living character provided by the thiocarbonyl end-group. Extensive dialysis and cleaning of the latex was performed to ensure no residual TBHP or reaction by-products remained. Latexes with poly(styrene) cores were chosen for this work as poly(n-butyl acrylate) latexes were shown to be influenced by chain transfer to polymer, providing an additional kinetic complication. The three electrosterically stabilized emulsions were used as seed latexes in carefully designed kinetic experiments to measure the rate of polymerization as a function of time. Two independent techniques (chemically initiated dilatometry and γ-relaxation dilatometry) were used to measure the rate coefficients of radical entry (ρ) and exit (k) in these systems – the two parameters that essentially govern the rate of particle growth. The latexes were chosen such that they satisfied ‘zero-one’ conditions (i.e. that any given latex particle contains at most one growing radical at any given time) in order to simplify data analysis. Three different chemical initiators were used, each yielding a radical with a different electric charge. Results from γ-relaxation experiments demonstrated that the three electrosterically stabilized latexes gave very long relaxation times when removed from the radiation source, ultimately yielding very small k values. These values were up to a factor of 10 smaller than that predicted by the ‘transfer-diffusion’ model for exit for particles of that size. This reduction was attributed to a ‘restricted diffusion’ effect, where the exiting monomeric radical has to diffuse through a dense layer of polymer on the particle surface, where its mobility will be restricted. Modification of the Smoluchowski equation for diffusion-controlled adsorption/desorption to account for this postulate led to the development of a model that gave excellent semi-quantitative agreement with experiment. Chemically initiated dilatometric experiments (using three different types of initiator) gave the unusual result of very low reaction rates and low steady-state values of 'nbar', the average number of radicals per particle. Using the standard kinetic equations for styrene-based systems (where it is assumed that an exited monomeric radical undergoes re-entry), this led to the calculation of impossibly small values of the entry rate coefficient ρ (far below any background or ‘thermal’polymerization rate). However upon removing the assumption of re-entry and assuming that exited radicals undergo termination, the obtained values of ρ were in almost perfect agreement with the values predicted from the ‘control by aqueous phase growth’ entry mechanism. This unexpected result was attributed to chemical reaction with the poly(acrylic acid) stabilizers through chain transfer to polymer (via hydrogen-atom abstraction). This postulate was verified by separate experiments that demonstrated that poly(acrylic acid) could act as a reasonably efficient chain transfer agent for styrene polymerization. The addition of poly(acrylic acid) to the aqueous phase of a conventionally stabilized emulsion also led to the rate reduction seen previously. NMR experiments demonstrated the existence of poly(acrylic acid-graft-styrene), which could only be formed through termination of a poly(styrene) chain with a poly(acrylic acid) chain bearing a mid-chain radical (as the product of a chain transfer reaction). These additional terms of transfer and termination were included in the governing kinetic equations of emulsion systems (the Smith-Ewart equations) to develop a model to account for the behaviour of electrosterically stabilized latexes. The ultimate fate of an exiting radical was now shown to be a competition between fates; successful desorption into the aqueous phase, or chemical reaction (through transfer or termination) within the hairy layer. These additional terms were shown to significantly reduce the theoretical value of nbar, and were in excellent agreement with experiment. For small electrosterically stabilized particles with a densely packed ‘hairy layer,’ it was seen that transfer/termination is the dominant loss mechanism as opposed to desorption. The developed model showed that as the particle size was increased, the dominant loss mechanism once again became successful desorption into the aqueous phase. The model was shown to give excellent agreement with experimental data from ‘uncontrolled’ emulsion systems. To explain the highly unusual secondary nucleation behaviour seen in systems such as these, it was postulated that beta-scission of a poly(acrylic acid) chain bearing a mid-chain radical is an important mechanistic step in the nucleation mechanisms of these systems. Modelling (both steady-state and time-dependent) gave good agreement with experiment with a minimal number of adjustable parameters. Theory (and supporting experimental evidence) demonstrated that this nucleation mechanism is only significant at high particle numbers; under other conditions the well-known ‘homogeneous nucleation’ mechanism is once again dominant.

Composites, in which the matrix and the reinforcing fillers are respectively, poly(acrylic acid) (PAA) with two different molecular weights, and chitin whiskers (CHW) were successfully prepared using an evaporation method. The weight fraction of CHW was varied from 0.03 to 0.73. Mechanical and thermal properties and crystallinity of the composites were characterised using tensile testing, differential scanning calorimetry, thermogravimetric analysis and X-ray diffraction. The tensile strength of the composite increased up to 11 wt % CHW after which it decreased. XRD characterisation showed a decrease in crystalline index, crystalline size, chitin crystalline peak and intensity as the content of PAA and its molecular weight increased. Raman spectroscopy was used for the first time to monitor the deformation of chitin film and CHW reinforced PAA composites. The Raman band located at 1622 cm^(-1) was monitored for deformation. On application of tensile deformation the Raman band initially located at 1622 cm^(-1) shifted toward a lower wavenumber. Raman band shift rates of -1.85 cm^(-1)/% for chitin film and -0.59 and -0.25 cm^(-1)/% for 73 and 23 wt % CHW content, respectively, were measured. The modulus of a single chitin whisker and composites were found to be 115, 37 and 16 GPa respectively, for a two dimensional (2D) in-plane distribution of CHW. CHW within a PAA matrix did not show any preferential alignment in a polarised Raman. The Raman intensity ratio〖 I〗_1698 /I_1622 showed that the strongest interaction of the carboxylic group in the composites occured at 3 wt % CHW content. The interaction gradually reduced as the CHW content increased. 〖 CaCO〗_3 crystals were grown in CHW, PAA and CHW/PAA composites by a solution and evaporation casting method. In the absence of PAA and CHW, rhombohedral calcites were observed while rod-like aragonite polymorphs were seen when only PAA was used as a template. In the presence of only CHW, a morphological mixture of ellipsoidal and disc shape with traces of rhombohedral aggregate calcite were the features. In the presence of both PAA and CHW, the rhombohedral shape showed roughness with irregular faces while the vaterite polymorph continued to agglomerate with the observation of porosity at higher CHW content. The vaterite particles gradually decreased as the CHW content was decreased. At lower CHW content aragonite polymorph growth was favoured to the detriment of calcite. The results showed that the vaterite polymorph can be grown even at higher filler loading. The effect of 〖 CaCO〗_3 growth on the mechanical properties of CHW reinforced PAA indicated that better mechanical properties can be achieved at a CHW content of 3 wt % when compared with neat PAA and when 〖 CaCO〗_3 was not incorporated into the CHW/25PAA composites.

This dissertation focuses on synthesis and characterization of graft and block copolymers containing carboxylate or phosphonate anions that are potential candidates for biomedical applications such as drug delivery and dental adhesives. Ammonium bisdiethylphosphonate (meth)acrylate and acrylamide phosphonate monomers were synthesized based on aza-Michael addition reactions. Free radical copolymerizations of these monomers with an acrylate-functional poly(ethylene oxide) (PEO) macromonomer produced graft copolymers. Quantitative deprotection of the alkylphosphonate groups afforded graft copolymers with zwitterionic ammonium bisphosphonate or anionic phosphonate backbones and PEO grafts. The zwitterionic copolymers spontaneously assembled into aggregates in aqueous media. The anionic copolymers formed aggregates in DMF and DMSO, while only small amounts of aggregates were present in copolymer/methanol or copolymer/water solutions. Binding capabilities of the acrylamide phosphonic acids were investigated through interactions with hydroxyapatite. Previously our group has prepared poly(ethylene oxide)-b-poly(acrylic acid) (PEO-b-PAA) copolymers and used these polymers as carriers for both MRI imaging agents and cationic drugs. To enhance the capabilities of those carriers in tracking and crosslinking, we have designed, synthesized and characterized amine functionalized PEO-b-PAA copolymers. First, heterobifunctional poly(ethylene oxide) (PEO) with three different molecular weights were synthesized. Modification on one of these afforded a PEO macroinitiator with a bromide on one end and a protected amine on the other end. ATRP polymerization of tert-butyl acrylate (tBuA) in the presence of this initiator and a copper (I) bromide (CuBr) catalyst yielded a diblock copolymer. The copolymer was deprotected by reaction with trifluoroacetic acid (TFA) and formed an amine terminated H2N-PEO-b-PAA. Recently our group has utilized the novel ammonium bisdiethylphosphonate (meth)acrylate and acrylamide phosphonate copolymers to incorporate Carboplatin. The resulting complexes exhibited excellent anticancer activity against MCF-7 breast cancer cells which might be related to ligand exchange of the dicarboxylate group of Carboplatin with the phosphonic acid moieties in the copolymer. Hence, complexation of small-molecule phosphonic acids with Carboplatin was investigated. Three compounds, vinylphosphonic acid, 3-hydroxypropyl ammonium bisphosphonic acid and 2-hydroxyethyl ammonium phosphonic acid were complexed with Carboplatin under acidic and neutral conditions. Covalent bonding of these acids to carboplatin was only observed under acidic pH. The covalently bonded percentage was 17%, 37% and 34%, respectively. More in-depth investigation was of great importance to further understand this complexation behavior. / Ph. D.

Yes / Fluorescence spectroscopy on a series of aqueous solutions of poly(acrylic acid) containing a luminescent label showed that polymers with molar mass, Mn < 16.5 kDa did not exhibit a pH responsive conformational change, which is typical of higher molar mass poly(acrylic acid). Below this molar mass, polymers remained in an extended conformation, regardless of pH. Above this molar mass, a pH-dependent conformational change was observed. Diffusion-ordered nuclear magnetic resonance spectroscopy confirmed that low molar mass polymers did not undergo a conformational transition, although large molar mass polymers did exhibit pH-dependent diffusion. / Engineering and Physical Sciences Research Council (EPSRC) funded CASE award PhD. Part funded by flocculant manufacturer SNF (UK) Ltd.

Oral mucositis is a painful and debilitating chronic inflammatory condition that can result from chemo and/or radiotherapy. While current treatment strategies which provide temporary relief exist, there is still an unmet clinical need for a robust long active barrier strategy which can simultaneously provide protection and release drug to enhance the wound healing response. It is proposed that an affinity based layer-by-layer self-assembled barrier administered as a series of mouth rinses can allow for wound specific drug delivery, providing an effective regenerative therapy. In this work, biotinylated poly(acrylic acid) is used to develop LBL assemblies based upon biotin-streptavidin affinity interactions. To explore the ability of developed LBL assemblies to resist the harsh intraoral environment, in vitro chemical and ex vivo mechanical tests are performed. The stability results demonstrate significant LBL barrier stability with wear resistance. From principal component regression analysis, factors such as polymer MW and number of layers in assemblies contributed significantly to chemical barrier stability. Also it is observed that the extent of biotin conjugation plays a significant role in LBL development and in mechanical stability. Thus, the proposed affinity based multilayered assemblies with their excellent barrier properties offer a modular treatment approach in oral mucosal injuries.

No description available.

Yes / There are many polymers formed of acrylate monomers in existence. Here we interrogate four commonly-used examples and study how their solution properties are pH dependent, or how their state of ionisation can affect their solution properties. Poly(acrylic acid) and poly(methacrylic acid) are both polyelectrolytes, with ionisable functional groups that make them stimuli responsive, changing their hydrodynamic volume. Poly(acrylamide) is a mass-produced material used in a variety of industrial applications, often with an anionic and cationic co-monomer, which dictates both its efficacy and impact on the environment. Poly(N-isopropyl acrylamide) is a thermally responsive material with applications in smart bioengineering. In solution, these materials can interact with each other due to competing hydrogen bonding interactions. However, this interpolymer complexation is dependent on both the ionisation, and the conformational state, of the polymers involved. This review focuses on the results from fluorescence tagging and turbidimetric techniques.

Ce travail de thèse décrit la synthèse de copolymères diblocs amphiphiles par polymérisation radicalaire contrôlée par transfert d'iode en mode inverse (RITP). Dans un premier temps, des homopolymères à base de monomères activés (styrène, acrylate de méthyle, méthacrylate de méthyle), non activés (acétate de vinyle) et fonctionnels (chlorométhylstyrène, acrylate de tert-butyle), ont été synthétisés par RITP. Des aspects tels que le contrôle des masses molaires ainsi que la fonctionnalité en iode du bout de chaîne ont été examinés. Afin de démontrer la compatibilité de la RITP avec d'autres techniques de polymérisation contrôlée/vivante (non radicalaires), le copolymère amphiphile non-ionique poly(styrène)-b-poly(2-méthyl-2-oxazoline) (PS-b-P(MOx)) a été élaboré par la voie toute iode en procédé « one-pot » en combinant de manière consécutive la RITP du styrène avec la polymérisation cationique par ouverture de cycle (CROP) de la 2-méthyl-2-oxazoline. Par ailleurs, des copolymères cationiques poly(styrène)-b-poly(chlorométhylstyrène) quaternisé avec la triéthylamine (PS-b-PCMS+) et anioniques poly(styrène)-b-poly(acide acrylique) (PS-b-PAA-) ont été synthétisés par RITP du styrène suivie de l'ITP du bloc hydrophile. Tous ces copolymères amphiphiles ont été obtenus à partir de polystyrène iodé (PS-I) de faibles masses molaires, allant de 1000 à 3000 g.mol-1, jouant le rôle de macro-amorceurs (CROP) ou de macro-agents de transfert (ITP). L'étude de l'auto-organisation en phase aqueuse de ces copolymères amphiphiles a révélé la formation de micelles pour des concentrations supérieures à la concentration d'agrégation critique (CAC) dont la valeur a été déterminée par diffusion dynamique de la lumière (DDL) et spectroscopie de fluorescence. Enfin, des résultats très prometteurs ont été obtenus dans l'utilisation d'un copolymère cationique amphiphile PS-b-PCMS+ comme agents structurants de matériaux siliciques mésoporeux nanostructurés élaborés par procédé sol-gel en milieu basique. La synthèse de ces copolymères amphiphiles ainsi que leur caractérisation physico-chimique ont mis en exergue que la RITP permet de couvrir la synthèse de différentes catégories de copolymères amphiphiles, tout en étant une technique simple à mettre en œuvre, peu couteuse et robuste. / This manuscript describes the synthesis of amphiphilic diblock copolymers by reverse iodine transfer polymerization (RITP). Firstly, homopolymers derived from activated (styrene, methyl acrylate, methyl methacrylate), non-activated (vinyl acetate) and functional monomers (chloromethylstyrene, tert-butyl acrylate) synthesized by RITP, were studied. Aspects including molecular weight control as well as iodine chain-end functionality were investigated. In order to highlight the compatibility of RITP with other living/controlled (non-radical) polymerization techniques, a poly(styrene)-b-poly(2-methyl-2-oxazoline) (PS-b-P(MOx)) non-ionic copolymer was conceived through an ‘all-iodine', ‘one-pot' process by combining successively RITP of styrene with cationic ring-opening polymerization (CROP) of 2-methyl-2-oxazoline. Besides, poly(styrene)-b-poly(chloromethylstyrene) quaternized with triethylamine (PS-b-PCMS+) cationic copolymers and poly(styrene)-b-poly(acrylic acid) (PS-b-PAA-) anionic copolymers were elaborated by RITP of styrene, followed by ITP of the hydrophilic moiety. All these amphiphilic copolymers were obtained from iodine-bearing chain-end poly(styrene) (PS-I) of low molecular weights, in the range of values of 1000 to 3000 g.mol-1, playing the role of macro-initiators (CROP) or macro-transfer agents (ITP). Studies of the self-assembly of these amphiphilic copolymers in aqueous phases revealed the formation of micelles for concentrations superior to the critical aggregation concentration (CAC). The latter value was determined by dynamic light scattering (DLS) and fluorescence spectroscopy. Moreover, highly-promising results were obtained in the use of PS-b-PCMS+ cationic copolymers as structuring agents meant for the elaboration of nanostructured, mesoporous silica-based materials through the sol-gel process in basic medium. Both the synthesis of the amphiphilic copolymers and their physico-chemical characterizations have evidenced that RITP fosters the synthesis of different categories of amphiphilic copolymers, while being a simple, cheap and robust technique.

Made available in DSpace on 2014-12-17T15:42:27Z (GMT). No. of bitstreams: 1 MariaSPL.pdf: 2188057 bytes, checksum: 3142bea2af0c353bf960b7b878efd707 (MD5) Previous issue date: 2006-11-17 / The aim of this study was to generate an asymmetric biocompactible and biodegradable chitosan membrane modi&#64257;ed by the contact with a poly(acrylic acid) solution at one of its sides at room temperature and 60&#9702;C. The pure chitosan membrane, as well as the ones treated with poly(acrylic acid) were characterized by infrared spectroscopy (FTIRATR) at angles of 39&#9702;, 45&#9702; and 60&#9702; , swelling capacity in water, thermal analysis (TG/DTG), scanning electronic microscopy (SEM) and permeation experiments using metronidazole at 0,1% and 0,2% as a model drug. The results con&#64257;rmed the presence of ionic interaction between chitosan and poly(acrylic acid) by means of a polyelectrolyte complex (PEC) formation. They also showed that such interactions were more effective at 60&#9702;C since this temperature is above the chitosan glass transition temperature wich makes the diffusion of poly(acrylic acid) easier, and that the two treated membranes were asymmetrics, more thermically stable and less permeable in relation to metronidazole than the pure chitosan membrane / O prop?sito deste estudo foi produzir uma membrana assim?trica biocompat?vel e biodegrad?vel de quitosana modi&#64257;cada pelo contato com uma solu??o de poli(?cido acr?lico) em uma de suas superf?cies ? temperatura ambiente e a 60&#9702;C. As membranas de quitosana pura, quitosana com poli(?cido acr?lico) a 25&#9702;C e quitosana com poli(?cido acr?lico) a 60&#9702;C foram caracterizadas por: espectroscopia no infravermelho (FTIRATR) em ?ngulos de incid?ncia de 39&#9702;, 45&#9702; e 60&#9702;, ganho de massa em ?gua, an?lise t?rmica (TG/ DTG), microscopia eletr?nica de varredura (MEV) e, ainda, atrav?s dos ensaios de permea??o in vitro utilizando como f?rmaco modelo o metronidazol em solu??o aquosa nas concentra??es de 0,1 e 0,2%. Os resultados obtidos comprovaram a exist?ncia de intera??es i?nicas entre os dois pol?meros, atrav?s da forma??o dos chamados complexos polieletrol?ticos. Tamb?m mostraram que a reticula??o foi mais efetiva a 60&#9702;C , uma vez que essa temperatura est? acima da temperatura de transi??o v?trea da quitosana, o que facilita a difus?o do poli(?cido acr?lico) e que as membranas resultantes s?o assim?tricas, mais est?veis termicamente e menos perme?veis ao metronidazol do que a membrana de quitosana pura

Biodegradable hydrogels have become very promising materials for a number of biomedical applications, including tissue engineering and drug delivery. For optimal tissue engineering design, the mechanical properties of hydrogels should match those of native tissues as closely as possible because these properties are known to affect the behavior and function of cells seeded in the hydrogels. At the same time, high water-contents, large mesh sizes and well-tuned degradation rates are favorable for the controlled release of growth factors and for adequate transport of nutrients through the hydrogel during tissue regeneration. With these factors in mind, the goal of this research was to develop and investigate the behavior of injectable, biodegradable hydrogels with enhanced stiffness properties that persist even at high degrees of swelling. In order to do this, degradable functionalities were incorporated into photo-crosslinkable poly(ethylene glycol) and poly(acrylic acid) hydrogels, and these two components were used to make a series of double-network hydrogels. Synthesis of the precursor macromers, photopolymerization of the hydrogels, and structural parameters of the hydrogels were analyzed. The composition and the molecular weight between crosslinks (Mc) of the hydrogel components were varied, and the degradation, swelling, thermal and mechanical properties of the hydrogels were characterized over various time scales. These properties were compared to corresponding properties of the component single-network hydrogels.