Recently wind resource assessment studies have become an important research tool to identify the possible wind farm locations.  In this thesis work technical analysis was carried out to determine the wind resource potential of two candidate sites in Eritrea with help of suitable software tools. The first site is located along the Red Sea cost which is well known for its wind resource potential, whereas the second site is located in the central highlands of Eritrea with significant wind resource potential. Detailed wind resource assessment, for one year hourly weather data including wind speed and wind direction, was performed for the two candidate sites using MS Excel and MATLAB. The measured wind data at Assab wind site showed that the mean wind speed and power density was 7.54 m/s and 402.57 W/m2 , whereas the mean wind speed and mean power density from Weibull distribution was 7.51 m/s and 423.71 W/m2 respectively at 80m height. Similarly, the measured mean wind speed and mean power density at Dekemahre wind site was obtained to be 5.498 m/s and 141.45 W/m2, whereas the mean wind speed and mean power density from Weibull distribution was 5.4859m/s and 141.057W/m2 respectively. Based on the analysis results Assab wind site classified as wind class-III and Dekemhare as wind class-I.  Wind farm modeling and Annual Energy Production (AEP) estimation was performed for E-82 & E-53 model turbines from Enercon Company with the help of MATLAB and Windpro software. The analysis revealed that Assab wind farm was an ideal site for wind energy production with capacity factor (CF) 53.4% and 55% for E-82 and E-53 turbines respectively. The gross and net AEP for turbine E-82 at Assab wind farm was 469.5 GWh and 446.025 GWh respectively with 95% park efficiency. Similarly, the analysis showed that the CF in Dekemhare site was very low with typical value 14.2% and 15.26% for E-82 and E-53 turbines respectively. The gross and net AEP of that site for model turbine E-53 was 53.5 GWh and 50.825 GWh respectively with 5% wake loss. Finally, a simplified economic analysis was carried out to determine the economic feasibility of possible wind power projects in both sites by assuming investment cost 1600 €/kW for E-82 turbine and 2000 €/kW for E-53 turbine. The total wind farm investment cost was found to be 215.85 and 107.93 Million Euro for E-82 and E-53 model turbines respectively. The levelized cost of energy at Assab and Dekemhare wind farm for E-82 model turbine was 0.0307 €/kWh and 0.5526 €/kWh respectively. The analysis result show that the levelized cost of energy in Dekemhare wind fasrm was much higher than that of Assab wind farm.

Submitted by Mery Piedad Zamudio Igami (mery@ipen.br) on 2017-03-10T16:45:35Z No. of bitstreams: 0 / Made available in DSpace on 2017-03-10T16:45:35Z (GMT). No. of bitstreams: 0 / Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP) / O presente estudo foi realizado para verificar a possibilidade de redução do núcleo do reator IEA-R1 do IPEN/CNEN-SP. Cálculos neutrônicos foram desenvolvidos para um conjunto de novas configurações para que, a posteriori, a análise termo-hidráulica e de segurança pudessem ser realizadas. As novas configurações analisadas são menores por diversos motivos, como obter uma melhor utilização do combustível, melhor distribuição dos fluxos de nêutrons, dentre outros. Para que se possa atingir tais configurações, a densidade de Urânio no combustível deve ser aumentada. Neste estudo, combustíveis de U3Si2-Al com 4,8gU/cm3 foram testados e novos núcleos para o reator IEA-R1 foram propostos e discutidos. A análise neutrônica não impõe restrições aos núcleos estudados. A análise termohidráulica mostrou que as margens de segurança e os perfis de temperatura ao longo das placas combustíveis não excedem os limites de projeto. Os coeficientes de temperatura obtidos para os novos núcleos, no caso isotérmico, são todos negativos, conforme desejado. A queima mostrou que núcleos supercompactos não apresentam excesso de reatividade suficiente para o funcionamento dos mesmo, ao se utilizar combustíveis com 4,8gU/cm3. Um APR (Acidente de Perda de Refrigerante) foi simulado para os núcleos remanescentes. A ruptura da fronteira do primário se mostrou o acidente mais crítico, devido ao curto tempo para o esvaziamento completo da piscina do reator. As temperaturas atingidas após o descobrimento foram calculadas e não excedem aquelas cujos valores propiciam empolamento nas placas combustíveis (475 °! a 550 °!), uma vez que se obedeça os tempos de esvaziamento seguro da piscina para as novas configurações. / Tese (Doutorado em Tecnologia Nuclear ) / IPEN/D / Instituto de Pesquisas Energéticas e Nucleares - IPEN-CNEN/SP / FAPESP: 11/17090-7

No description available.

Die Bedeutung von Leistungshalbleitern mit großem Bandabstand (Wide Band Gap, WBG) nahm in den letzten drei Jahrzehnten kontinuierlich zu. Diese Bauelemente haben das Potenzial, Silizium (Si) - Bauelemente in bestimmten Anwendungen sowie Leistungs- und Frequenzbereichen zu ersetzen. Siliziumkarbid (SiC)-Leistungshalbleiter sind die gegenwärtig am Weitesten entwickelten WBG-Leistungshalbleiter. Dank besonderer Materialeigenschaften zeichnen sich SiC-Leistungshalbleiter im Vergleich zu Si-Bauelementen durch einen geringeren spezifischen Widerstand, eine höhere Schaltgeschwindigkeit, geringere schaltverluste sowie eine höhere maximale Sperrschichttemperatur aus. Die deutlich erhöhten Herstellungskosten limitieren den Einsatz von SiC-Leistungshalbleitern auf Anwendungen, in denen die Vorteile dieser Bauelemente die höheren Kosten überkompensieren und Systemvorteile ermöglichen. Heute werden SiC-Leistungshalbleiter z.B. in Solarwechselrichtern oder in Elektrofahrzeugen verwendet. Für Stromrichter industrieller elektrischer Antriebe ist die Kosten-Nutzen-Bilanz des Einsatzes von SiC-Leistungshalbleitern gegenwärtig nicht bekannt. Diese Fragestellung motiviert diese Arbeit. Die Auslegung sowie die daraus resultierenden Vor- und Nachteile eines Stromrichters mit SiC-Leistungshalbleitern für elektrische Industrieantriebe ist der Untersuchungsgegenstand dieser Arbeit. Zu diesem Zweck wurde unter Einhaltung industrieller Auslegungskriterien ein 240 kVA SiC-basierter Stromrichterdemonstrator als aktiver Gleichrichter am dreiphasigen 690 V Niederspannungsnetz untersucht. Auf der Basis einer Stromrichterauslegung für SiC- und Si-Leistungshalbleiter wurde ein theoretischer Vergleich von Kosten, Effizienz, Größe und Gewicht durchgeführt. Die Arbeit stellt zunächst den Stand der Technik für SiC-Leistungshalbleiter dar. Anschließend wird ein geeignetes SiC-MOSFET Module für den industriellen Stromrichter ausgewählt und bezüglich des Schaltverhaltens sowie der Parallelschaltung charakterisiert. Der Auslegung des Stromrichterleistungsteils liegen industrielle Anforderungen zu Grunde. Ein realisierter Demonstrator für einen netzseitigen Stromrichter (Active Front End) ist durch eine symmetrische Parallelschaltung von zwei SiC-Modulen, geeignete Ansteuerschaltungen (Gate Drive Units), eine niedrige Streuinduktivität im Kommutierungskreis sowie ein LCL-Filter mit Standard-Kernmaterialien gekennzeichnet. Der Stromrichtervergleich zeigt, dass der betrachtete Stromrichter mit SiC-Leistungshalbleitern im gesamten Betriebsbereich geringere Verluste verursacht als ein vergleichbarer Stromrichter mit Si-Leistungshalbleitern. Der SiC - basierte Stromichter ermöglicht auch eine deutliche Gewichtsreduktion bei ca. 89% der Systemkosten. Somit stellen SiC-Leistungshalbleiter eine attraktive technische Lösung für die untersuchte Anwendung eines aktiven Gleichrichters für industrielle elektrische Antriebe dar. / Wide bandgap (WBG) power semiconductors have drawn steadily increasing interest in power electronics in the last three decades. These devices have shown the potential of replacing silicon as the default semiconductor solution for several applications in determined power and frequency ranges. Among them the most mature WBG semiconductor material is silicon carbide (SiC), which presents several characteristics at the crystal level that translate in the potential of presenting lower resistivity, be able to switch faster with lower switching loss, and present both higher characteristics to tolerate and dissipate heat when com pared with silicon. However, the same characteristics that make it great also present a different set of drawbacks to be considered, which aligned with its increased cost make it challenging to assess if its advantages are justified for a particular application. Applications that highly value efficiency and/or power density are the most benefited, and converter solutions featuring the technology have already breached into these application markets. However in other applica tions, the line from which silicon carbide starts making sense in the cost/benefits/drawbacks balance is not clear. This is typically the case of industrial applications, which were the main focus and motivation of this work. Hence, in this work the main goal has been to determine the basic characteristics, advantages and limitations that SiC technology designs for industrial low voltage high power grid connected converters present. To that end, a 690 V, 240 kVA SiC-based grid-tied converter demonstrator following industrial design criteria has been developed. Then, based on this design procedure a theoretical comparison between a 690 V, 190 kVA SiC-based converter against a silicon-based converter designed for the same power output has been performed to compare them regarding cost, efficiency, size and weight. This work also comprises a thorough revision of the state of art of SiC devices, which led to the selection of the switching device. Additionally, a characterization of both single and parallel-connected operation of the semiconductor modules was performed, to determine the module characteristics and its suitability to build the SiC converter demonstrator. Results show that the converter demonstrator operates as designed, proving that is possible with the corresponding precautions to achieve: a low inductive power loop, balanced parallel connection of SiC modules, adequate driving circuits for the parallel-connected modules and an adequate filtering solution in compliance with grid-codes based on standard core materials for the selected switching frequency. Finally, the theoretical comparison between the two designed power converters shows that, attained to the conditions of the comparison, the SiC converter solution presents efficiency gains over the whole operating range, while presenting substantial weight savings at 89% of the costs of the Si-IGBT design, presenting itself as the cost-effective solution for the presented application requirements under the given design constraints.

With the rapid development of microprocessor and semiconductor technology, industry continues to update the requirements for power supplies. For telecommunication and computing system applications, power supplies require increasing current level while the supply voltage keeps decreasing. For example, the Intel's CPU core voltage decreased from 2 volt in 1999 to 1 volt in 2005 while the supply current increased from 20A in 1999 to up to 100A in 2005. As a result, low-voltage high-current high efficiency dc-dc converters with high power-density are demanded for state-of-the-art applications and also the future applications. Half-bridge dc-dc converter with current-doubler rectification is regarded as a good topology that is suitable for high-current low-voltage applications. There are three control schemes for half-bridge dc-dc converters and in order to provide a valid unified analog model for optimal compensator design, the analog state-space modeling and small signal modeling are studied in the dissertation and unified state-space and analog small signal model are derived. In addition, the digital control gains a lot of attentions due to its flexibility and re-programmability. In this dissertation, a unified digital small signal model for half-bridge dc-dc converter with current doubler rectifier is also developed and the digital compensator based on the derived model is implemented and verified by the experiments with the TI DSP chip. In addition, although current doubler rectifier is widely used in industry, the key issue is the current sharing between two inductors. The current imbalance is well studied and solved in non-isolated multi-phase buck converters, yet few discusse this issue in the current doubler rectification topology within academia and industry. This dissertation analyze the current sharing issue in comparison with multi-phase buck and one modified current doubler rectifier topology is proposed to achieve passive current sharing. The performance is evaluated with half bridge dc-dc converter; good current sharing is achieved without additional circuitry. Due to increasing demands for high-efficiency high-power-density low-voltage high current topologies for future applications, the thermal management is challenging. Since the secondary-side conduction loss dominates the overall power loss in low-voltage high-current isolated dc-dc converters, a novel current tripler rectification topology is proposed. Theoretical analysis, comparison and experimental results verify that the proposed rectification technique has good thermal management and well-distributed power dissipation, simplified magnetic design and low copper loss for inductors and transformer. That is due to the fact that the load current is better distributed in three inductors and the rms current in transformer windings is reduced. Another challenge in telecommunication and computing applications is fast transient response of the converter to the increasing slew-rate of load current change. For instance, from Intel's roadmap, it can be observed that the current slew rate of the age regulator has dramatically increased from 25A/uS in 1999 to 400A/us in 2005. One of the solutions to achieve fast transient response is secondary-side control technique to eliminate the delay of optocoupler to increase the system bandwidth. Active-clamp half bridge dc-dc converter with secondary-side control is presented and one industry standard 16th prototype is built and tested; good efficiency and transient response are shown in the experimental section. However, one key issue for implementation of secondary-side control is start-up. A new zero-voltage-switching buck-flyback isolated dc-dc converter with synchronous rectification is proposed, and it is only suitable for start-up circuit for secondary-side controlled converter, but also for house-keeping power supplies and standalone power supplies requiring multi-outputs.

No description available.

Enhancing performance of power electronics converters has always been an interesting topic in the power electronics community. Over the years, researchers and engineers are developing new high performance component, novel converter topologies, smart control methods and optimal design procedures to improve the efficiency, power density, reliability and reducing the cost. Besides pursuing high performance, researchers and engineers are striving to modularize the power electronics converters, which provides redundancy, flexibility and standardization to the end users. The trend of modularization has been seen in photovoltaic inverters, telecommunication power supplies, and recently, HVDC applications. A systematic optimal design approach for modular power converters is developed in this dissertation. The converters are developed for aerospace applications where there are stringent requirement on converter form factor, loss dissipation, thermal management and electromagnetic interference (EMI) performance. This work proposed an optimal design approach to maximize the nominal power of the power converters considering all the constraints, which fully reveals the power processing potential. Specifically, this work studied three-phase active front-end converter, three-phase isolated ac/dc converter and inverter. The key models (with special attention paid to semiconductor switching loss model), detailed design procedures and key design considerations are elaborated. With the proposed design framework, influence of key design variables, e.g. converter topology, switching frequency, etc. is thoroughly studied. Besides optimal design procedure, control issues in paralleling modular converters are discussed. A master-slave control architecture is used. The slave controllers not only follow the command broadcasted by the master controller, but also synchronize the high frequency clock to the master controller. The control architecture eliminates the communication between the slave controllers but keeps paralleled modules well synchronized, enabling a fully modularized design. Furthermore, the implementation issues of modularity are discussed. Although modularizing converters under form factor constraints adds flexibility to the system, it limits the design space by forbidding oversized components. This work studies the influence of the form factor by exploring the maximal nominal power of a double-sized converter module and comparing it with that of two paralleled modules. The tradeoff between modularity and performance is revealed by this study. Another implementation issue is related to EMI. Scaling up system capacity by paralleling converter modules induces EMI issues in both signal level and system level. This work investigates the mechanisms and provides solutions to the EMI problems. / Ph. D. / As penetration of power electronics technologies in electric power delivery keeps increasing, performance of power electronics converters becomes a key factor in energy delivery efficacy and sustainability. Enhancing performance of power electronics converters reduces footprint, energy waste and delivery cost, and ultimately, promoting a sustainable energy use. Over the years, researchers and engineers are developing new technologies, including high performance component, novel converter topologies, smart control methods and optimal design procedures to improve the efficiency, power density, reliability and reducing the cost of power electronics converters. Besides pursuing high performance, researchers and engineers are striving to modularize the power electronics converters, enabling power electronics converters to be used in a “plug-and-play” fashion. Modularization provides redundancy, flexibility and standardization to the end users. The trend of modularization has been seen in applications that process electric power from several Watts to Megawatts. This dissertation discusses the design framework for incorporating modularization into existing converter design procedure, synergically achieving performance optimization and modularity. A systematic optimal design approach for modular power converters is developed in this dissertation. The converters are developed for aerospace applications where there is stringent v requirement on converter dimensions, loss dissipation, and thermal management. Besides, to ensure stable operation of the onboard power system, filters comprising of inductors and capacitors are necessary to reduce the electromagnetic interference (EMI). Owning to the considerable weight and size of the inductors and capacitors, filter design is one of the key component in converter design. This work proposed an optimal design approach that synergically optimizes performance and promotes modularity while complying with the entire aerospace requirement. Specifically, this work studied three-phase active front-end converter, three-phase isolated ac/dc converter and three-phase inverter. The key models, detailed design procedures and key design considerations are elaborated. Experimental results validate the design framework and key models, and demonstrates cutting-edge converter performance. To enable a fully modularized design, control of modular converters, with focus on synchronizing the modular converters, is discussed. This work proposed a communication structure that minimizes communication resources and achieves seamless synchronization among multiple modular converters that operate in parallel. The communication scheme is demonstrated by experiments. Besides, the implementation issues of modularity are discussed. Although modularizing converters under form factor constraints adds flexibility to the system, it limits the design space by forbidding oversized components. This work studies the impact of modularity by comparing performance of a double-sized converter module with two paralleled modules. The tradeoff between modularity and performance is revealed by this study.

Perhaps surprisingly, the largest experience in operating nuclear power plants has been in nuclear naval propulsion, particularly submarines. This accumulated experience may become the basis of a proposed new generation of compact nuclear power plant designs. In an effort to de-carbonise commercial freight shipping, there is growing interest in the possibility of using nuclear propulsion systems. Reactor cores for such an application would need to be fundamentally different from land-based power generation systems, which require regular refueling, and from reactors used in military submarines, as the fuel used could not conceivably be as highly enriched. Nuclear-powered propulsion would allow ships to operate with low fuel costs, long refueling intervals, and minimal emissions; however, currently such systems remain largely confined to military vessels. This research project undertakes computational modeling of possible soluble-boron-free (SBF) reactor core designs for this application, with a view to informing design decisions in terms of choices of fuel composition, materials, core geometry and layout. Computational modeling using appropriate reactor physics (e.g. WIMS, MONK, Serpent and PANTHER), thermal-hydraulics etc. codes (e.g. COBRA-EN) is used for this project. With an emphasis on reactor physics, this study investigates possible fuel assembly and core designs for civil marine propulsion applications. In particular, it explores the feasibility of using uranium/thorium-rich fuel in a compact, long-life reactor and seek optimal choices and designs of the fuel composition, reactivity control, assembly geometry, and core loading in order to meet the operational needs of a marine propulsion reactor. In this reactor physics and 3D coupled neutronics/thermal-hydraulics study, we attempt to design a civil marine reactor core that fulfills the objective of providing at least 15 effective full-power-years (EFPY) life at 333 MWth. In order to unleash the benefit of thorium in a long life core, the micro-heterogeneous ThO2-UO2 duplex fuel is well-positioned to be utilized in our proposed civil marine core. Unfortunately, A limited number of studies of duplex fuel are available in the public domain, but its use has never been examined in the context of a SBF environment for long-life small modular rector (SMR) core. Therefore, we assumed micro-heterogeneous ThO2-UO2 duplex fuel for our proposed marine core in order to explore its capability. For the proposed civil marine propulsion core design, this study uses 18% U-235 enriched micro-heterogeneous ThO2-UO2 duplex fuel. To provide a basis for comparison we also evaluate the performance of homogeneously mixed 15% U-235 enriched all-UO2 fuel. This research also attempts to design a high power density core with 14 EFPY while satisfying the neutronic and thermal-hydraulics safety constraints. A core with an average power density of 100 MW/m3 has been successfully designed while obtaining a core life of 14 years. The average core power density for this core is increased by ∼50% compared to the reference core design (63 MW/m3 and is equivalent to Sizewell B PWR (101.6 MW/m3 which means capital costs could be significantly reduced and the economic attractiveness of the marine core commensurately improved. In addition, similar to the standard SMR core, a reference core with a power density of 63 MW/m3 has been successfully designed while obtaining a core life of ∼16 years. One of the most important points that can be drawn from these studies is that a duplex fuel lattice needs less burnable absorber than uranium-only fuel to achieve the same poison performance. The higher initial reactivity suppression and relatively smaller reactivity swing of the duplex can make the task of reactivity control through BP design in a thorium-rich core easier. It is also apparent that control rods have greater worth in a duplex core, reducing the control material requirements and thus potentially the cost of the rods. This research also analyzed the feasibility of using thorium-based duplex fuel in different cases and environments to observe whether this fuel consistently exhibit superior performance compared to the UO2 core in both the assembly and whole-core levels. The duplex fuel/core consistently exhibits superior performance in consideration of all the neutronic and TH constraints specified. It can therefore be concluded from this study that the superior performance of the thorium-based micro-heterogeneous ThO2-UO2 duplex fuel provides enhanced confidence that this fuel can be reliably used in high power density and long-life SBF marine propulsion core systems, offering neutronic advantages compared to the all-UO2 fuel. Last, but not least, considering all these factors, duplex fuel can potentially open the avenue for low-enriched uranium (LEU) SBF cores with different configurations. Motivated by growing environmental concerns and anticipated economic pressures, the overall goal of this study is to examine the technological feasibility of expanding the use of nuclear propulsion to civilian maritime shipping and to identify and propose promising candidate core designs.

A breed-and-burn molten salt reactor (BBMSR) concept is proposed to address the Generation IV fuel cycle sustainability objective in a once-through cycle with low enrichment and no reprocessing. The BBMSR uses separate fuel and coolant molten salts, with the fuel contained in assemblies of individual tubes that can be shuffled and reclad periodically to enable high burnup. In this dual-salt configuration, the BBMSR may overcome several limitations of previous breed-and-burn (B$\&$B) designs to achieve high uranium utilisation with a simple, passively safe design. A central challenge in design of the BBMSR fuel is balancing the neutronic requirement of large fuel volume fraction for B$\&$B mode with the thermal-hydraulic requirements for safe and economically competitive reactor operation. Natural convection of liquid fuel within the tubes aids heat transfer to the coolant, and a systematic approach is developed to efficiently model this complex effect. Computational fluid dynamics modelling is performed to characterise the unique physics of the system and produce a new heat transfer correlation, which is used alongside established correlations in a numerical model. A design framework is built around this numerical model to iteratively search for the limiting power density of a given fuel and channel geometry, applying several defined temperature and operational constraints. It is found that the trade-offs between power density, core pressure drop, and pumping power are lessened by directing the flow of coolant downwards through the channel. Fuel configurations that satisfy both neutronic and thermal-hydraulic objectives are identified for natural, 5$\%$ enriched, and 20$\%$ enriched uranium feed fuel. B$\&$B operation is achievable in the natural and 5$\%$ enriched versions, with power densities of 73 W/cm$^3$ and 86 W/cm$^3$, and theoretical uranium utilisations of 300 $\mathrm{MWd/kgU_{NAT}}$ and 25.5 $\mathrm{MWd/kgU_{NAT}}$, respectively. Using 20$\%$ enriched feed fuel relaxes neutronic constraints so a wider range of fuel configurations can be considered, but there is a strong inverse correlation between power density and uranium utilisation. The fuel design study demonstrates the flexibility of the BBMSR concept to operate along a spectrum of modes ranging from high fuel utilisation at moderate power density using natural uranium feed fuel, to high power density and moderate utilisation using 20$\%$ uranium enrichment.

No description available.