Global ETD Search

81	Cooling of electrically insulated high voltage electrodes down to 30 mK / Kühlung von elektrisch isolierten Hochspannungselektroden bis 30 mK Eisel, Thomas 07 November 2011 (has links) (PDF) The Antimatter Experiment: Gravity, Interferometry, Spectroscopy (AEGIS) at the European Organization for Nuclear Research (CERN) is an experiment investigating the influence of earth’s gravitational force upon antimatter. To perform precise measurements the antimatter needs to be cooled to a temperature of 100 mK. This will be done in a Penning trap, formed by several electrodes, which are charged with several kV and have to be individually electrically insulated. The trap is thermally linked to a mixing chamber of a 3He-4He dilution refrigerator. Two link designs are examined, the Rod design and the Sandwich design. The Rod design electrically connects a single electrode with a heat exchanger, immersed in the helium of the mixing chamber, by a copper pin. An alumina ring and the helium electrically insulate the Rod design. The Sandwich uses an electrically insulating sapphire plate sandwiched between the electrode and the mixing chamber. Indium layers on the sapphire plate are applied to improve the thermal contact. Four differently prepared test Sandwiches are investigated. They differ in the sapphire surface roughness and in the application method of the indium layers. Measurements with static and sinusoidal heat loads are performed to uncover the behavior of the thermal boundary resistances. The thermal total resistance of the best Sandwich shows a temperature dependency of T-2,64 and is significantly lower, with roughly 30 cm2K4/W at 50 mK, than experimental data found in the literature. The estimated thermal boundary resistance between indium and sapphire agrees very well with the value of the acoustic mismatch theory at low temperatures. In both designs, homemade heat exchangers are integrated to transfer the heat to the cold helium. These heat exchangers are based on sintered structures to increase the heat transferring surface and to overcome the significant influence of the thermal resistance (Kapitza resistance). The heat exchangers are optimized concerning the adherence of the sinter to the substrate and its sinter height, e.g. its thermal penetration length. Ruthenium oxide metallic resistors (RuO2) are used as temperature sensors for the investigations. They consist of various materials, which affect the reproducibility. The sensor conditioning and the resulting good reproducibility is discussed as well. cooling dilution refrigerator millikelvin high voltage electrical insulation thermal contact conductance thermal boundary resistance sapphire indium acoustic mismatch sintered heat exchanger sinter height thermal penetration length Kapitza resistance RuO2 sensor ruthenium oxide temperature sensor thermal cycling sensor conditioning micro cracks Kühlung Mischungskryostat Millikelvin Hochspannung elektrische Isolierung Thermischer Kontaktwiderstand Saphir Indium Acoustic Mismatch Theorie gesinterte Wärmeübertrager Sinterhöhe thermische Eindringtiefe Kapitza Widerstand RuO2-Sensor Ruthenium Oxid Temperatursensor thermisches Zyklieren Sensor-Konditionierung Mikrorisse ddc:620 rvk:UB 5180
82	Cooling of electrically insulated high voltage electrodes down to 30 mK Eisel, Thomas 04 October 2011 (has links) The Antimatter Experiment: Gravity, Interferometry, Spectroscopy (AEGIS) at the European Organization for Nuclear Research (CERN) is an experiment investigating the influence of earth’s gravitational force upon antimatter. To perform precise measurements the antimatter needs to be cooled to a temperature of 100 mK. This will be done in a Penning trap, formed by several electrodes, which are charged with several kV and have to be individually electrically insulated. The trap is thermally linked to a mixing chamber of a 3He-4He dilution refrigerator. Two link designs are examined, the Rod design and the Sandwich design. The Rod design electrically connects a single electrode with a heat exchanger, immersed in the helium of the mixing chamber, by a copper pin. An alumina ring and the helium electrically insulate the Rod design. The Sandwich uses an electrically insulating sapphire plate sandwiched between the electrode and the mixing chamber. Indium layers on the sapphire plate are applied to improve the thermal contact. Four differently prepared test Sandwiches are investigated. They differ in the sapphire surface roughness and in the application method of the indium layers. Measurements with static and sinusoidal heat loads are performed to uncover the behavior of the thermal boundary resistances. The thermal total resistance of the best Sandwich shows a temperature dependency of T-2,64 and is significantly lower, with roughly 30 cm2K4/W at 50 mK, than experimental data found in the literature. The estimated thermal boundary resistance between indium and sapphire agrees very well with the value of the acoustic mismatch theory at low temperatures. In both designs, homemade heat exchangers are integrated to transfer the heat to the cold helium. These heat exchangers are based on sintered structures to increase the heat transferring surface and to overcome the significant influence of the thermal resistance (Kapitza resistance). The heat exchangers are optimized concerning the adherence of the sinter to the substrate and its sinter height, e.g. its thermal penetration length. Ruthenium oxide metallic resistors (RuO2) are used as temperature sensors for the investigations. They consist of various materials, which affect the reproducibility. The sensor conditioning and the resulting good reproducibility is discussed as well. info:eu-repo/classification/ddc/620 ddc:620
83	Characterization of heterogeneous diffusion in confined soft matter Täuber, Daniela 26 October 2011 (has links) (PDF) A new method, probability distribution of diffusivities (time scaled square displacements between succeeding video frames), was developed to analyze single molecule tracking (SMT) experiments. This method was then applied to SMT experiments on ultrathin liquid tetrakis(2-ethylhexoxy)silane (TEHOS) films on Si wafer with 100 nm thermally grown oxide, and on thin semectic liquid crystal films. Spatial maps of diffusivities from SMT experiments on 220 nm thick semectic liquid crystal films reveal structure related dynamics. The SMT experiments on ultrathin TEHOS films were complemented by fluorescence correlation spectroscopy (FCS). The observed strongly heterogeneous single molecule dynamics within those films can be explained by a three-layer model consisting of (i) dye molecules adsorbed to the substrate, (ii) slowly diffusing molecules in the laterally heterogeneous near-surface region of 1 - 2 molecular diameters, and (iii) freely diffusing dye molecules in the upper region of the film. FCS and SMT experiments reveal a strong influence of substrate heterogeneity on SM dynamics. Thereby chemisorption to substrate surface silanols plays an important role. Vertical mean first passage times (mfpt) in those films are below 1 µs. This appears as fast component in FCS autocorrelation curves, which further contain a contribution from lateral diffusion and from adsorption events. Therefore, the FCS curves are approximated by a tri-component function, which contains an exponential term related to the mfpt, the correlation function for translational diffusion and a stretched exponential term for the broad distribution of adsorption events. Lateral diffusion coefficients obtained by FCS on 10 nm thick TEHOS films, thereby, are effective diffusion coefficients from dye transients in the focal area. They strongly depend on the substrate heterogeneity. Variation of the frame times for the acquisition of SMT experiments in steps of 20 ms from 20 ms to 200 ms revealed a strong dependence of the corresponding probability distributions of diffusivities on time, in particular in the range between 20 ms and 100 ms. This points to average dwell times of the dye molecules in at least one type of the heterogeneous regions (e.g. on and above silanol clusters) in the range of few tens of milliseconds. Furthermore, time series of SM spectra from Nile Red in 25 nm thick poly-n-alkyl-methacrylate (PnAMA) films were studied. In analogy to translational diffusion, spectral diffusion (shifts in energetic positions of SM spectra) can be studied by probability distributions of spectral diffusivities, i.e. time scaled square energetic displacements. Simulations were run and analyzed to study contributions from noise and fitting uncertainty to spectral diffusion. Furthermore the effect of spectral jumps during acquisition of a SM spectrum was investigated. Probability distributions of spectral diffusivites of Nile Red probing vitreous PnAMA films reveal a two-level system. In contrast, such probability distributions obtained from Nile Red within a 25 nm thick poly-n-butylmethacrylate film around glass transition and in the melt state, display larger spectral jumps. Moreover, for longer alkyl side chains a solvent shift to higher energies is observed, which supports the idea of nanophase separation within those polymers. heterogene Diffusion fest-flüssig Grenzfläche Lagenbildung Einzelmoleküldetektion Fluoreszenzmikroskopie Fluoreszenzkorrelationsspektroskopie Einzelmolekülverfolgung Simulation weiche Materie TEHOS smektisch-A 8CB Poly-n-alkylmethacrelat ultradünne Flüssigkeitsfilme dünne Flüssigkristallfilme dünne Polymerfilme Oberflächensilanole thermisches SiO2 spektrale Diffusion heterogeneous diffusion solid-liquid interface liquid layering single molecule detection fluorescence microscopy fluorescence correlation spectroscopy single molecule tracking simulation soft matter TEHOS smectic-A 8CB poly-n-alkyl methacrylate ultrathin liquid films thin liquid crystal films thin polymer films surface silanols thermally grown SiO2 spectral diffusion ddc:530 ddc:541 Weiche Materie Fluoreszenzmikroskopie Thermotroper Flüssigkristall Flüssigkristall-Farbstoff-System Flüssigkeitsfilm Polymerfilm Anisotrope Diffusion Anomale Diffusion Diffusion Optisches Spektrum Nanostrukturiertes Material Simulation
84	Characterization of heterogeneous diffusion in confined soft matter Täuber, Daniela 20 October 2011 (has links) A new method, probability distribution of diffusivities (time scaled square displacements between succeeding video frames), was developed to analyze single molecule tracking (SMT) experiments. This method was then applied to SMT experiments on ultrathin liquid tetrakis(2-ethylhexoxy)silane (TEHOS) films on Si wafer with 100 nm thermally grown oxide, and on thin semectic liquid crystal films. Spatial maps of diffusivities from SMT experiments on 220 nm thick semectic liquid crystal films reveal structure related dynamics. The SMT experiments on ultrathin TEHOS films were complemented by fluorescence correlation spectroscopy (FCS). The observed strongly heterogeneous single molecule dynamics within those films can be explained by a three-layer model consisting of (i) dye molecules adsorbed to the substrate, (ii) slowly diffusing molecules in the laterally heterogeneous near-surface region of 1 - 2 molecular diameters, and (iii) freely diffusing dye molecules in the upper region of the film. FCS and SMT experiments reveal a strong influence of substrate heterogeneity on SM dynamics. Thereby chemisorption to substrate surface silanols plays an important role. Vertical mean first passage times (mfpt) in those films are below 1 µs. This appears as fast component in FCS autocorrelation curves, which further contain a contribution from lateral diffusion and from adsorption events. Therefore, the FCS curves are approximated by a tri-component function, which contains an exponential term related to the mfpt, the correlation function for translational diffusion and a stretched exponential term for the broad distribution of adsorption events. Lateral diffusion coefficients obtained by FCS on 10 nm thick TEHOS films, thereby, are effective diffusion coefficients from dye transients in the focal area. They strongly depend on the substrate heterogeneity. Variation of the frame times for the acquisition of SMT experiments in steps of 20 ms from 20 ms to 200 ms revealed a strong dependence of the corresponding probability distributions of diffusivities on time, in particular in the range between 20 ms and 100 ms. This points to average dwell times of the dye molecules in at least one type of the heterogeneous regions (e.g. on and above silanol clusters) in the range of few tens of milliseconds. Furthermore, time series of SM spectra from Nile Red in 25 nm thick poly-n-alkyl-methacrylate (PnAMA) films were studied. In analogy to translational diffusion, spectral diffusion (shifts in energetic positions of SM spectra) can be studied by probability distributions of spectral diffusivities, i.e. time scaled square energetic displacements. Simulations were run and analyzed to study contributions from noise and fitting uncertainty to spectral diffusion. Furthermore the effect of spectral jumps during acquisition of a SM spectrum was investigated. Probability distributions of spectral diffusivites of Nile Red probing vitreous PnAMA films reveal a two-level system. In contrast, such probability distributions obtained from Nile Red within a 25 nm thick poly-n-butylmethacrylate film around glass transition and in the melt state, display larger spectral jumps. Moreover, for longer alkyl side chains a solvent shift to higher energies is observed, which supports the idea of nanophase separation within those polymers. info:eu-repo/classification/ddc/530 ddc:530 info:eu-repo/classification/ddc/541 ddc:541

Page generated in 0.0678 seconds