Gegenstand der vorliegenden Arbeit ist die templatgestützte Erzeugung metallischer Stäbchen und Ringstrukturen im Mikrometer- und Nanometerbereich. Derartige Strukturen besitzen vor allem aufgrund ihres außergewöhnlichen Verhaltes gegenüber elektromagnetischen Wellen ein hohes Potential für optische, elektronische, magnetische oder sensorische Anwendungen. Zunächst wird das Vorgehen zur Herstellung mesoskopischer Ringe durch die Infiltration von Kolloidkristallen aus Siliziumdioxid mittels geeigneter Präkursorlösungen detailliert betrachtet. Daraufhin werden Ansätze zur Optimierung einzelner Teilschritte vorgestellt. Im Anschluss erfolgt die Übertragung des Verfahrens auf die Herstellung von Goldringen. Neben der elektronenmikroskopischen Charakterisierung der Proben wird unter anderem durch energiedispersive Röntgenspektroskopie (EDXS), Elektronenrückstreubeugung (EBSD) und Röntgenphotoelektronenspektroskopie (XPS) bestätigt, dass die entstandenen Strukturen aus metallischem Gold bestehen. Ein weiterer Inhalt dieser Arbeit ist die Konzeption und Umsetzung einer Apparatur zur elektrochemischen Erzeugung von mesoskopischen Metallstäbchen im Inneren von porösen Aluminiumoxidmembranen. Im Anschluss wird die Herstellung von Silber- und Goldstäbchen beschrieben. Außerdem wird aufgeführt, wie die sequenzielle Abscheidung der beiden Metalle unter anschließender Auflösung des metallischen Silbers zur Erhöhung der Ausbeute an isolierten Goldstäbchen führt.

In order to improve the purity of steel castings, the use of special reactive coatings on carbon-bonded ceramic foam filters was explored. Carbon nanotubes were dispersed in water by means of ultrasonic treatment, using xanthan gum to stabilize the nanotubes in suspension and control the rheological behavior. The coatings were applied by cold spraying and binding was achieved during heat treatment in reducing atmosphere, thanks to an artificial pitch added to the slurry. The coated filters were successfully immersed in molten steel for different times. The thickness of the first alumina layer generated at the interface was independent of the immersion time: concentration gradients through its thickness suggested that the formation of this structure is limited by diffusion. Investigation of the steel after solidification by means of ASPEX showed that the presence of the coating influenced the size as well as the chemical composition of the remaining inclusions. Nano-coated filters had the best filtration efficiency (up to 95% for alumina inclusions after 10 s), but longer tests resulted in worse performance. In addition, coatings based on calcium aluminates in combination with carbon showed an efficiency greater than 97% for steel samples taken directly from the melt.

[ES] La presente tesis doctoral titulada "New nanostructured suports with signal amplification features for the detection of molecules and biomolecules of interest" se centra en el diseño y preparación de nuevos materiales híbridos orgánicos-inorgánicos constituidos por puertas moleculares soportadas sobre alúmina mesoporosa con el objetivo de desarrollar nuevos sistemas sensores con aplicaciones potenciales en el campo de la diagnosis y del control alimentario. En el primer capítulo de la tesis se introducen los conceptos en los que están basados los estudios realizados y los materiales preparados. A continuación, en el segundo capítulo se describen los objetivos generales de la tesis que serán abordados en los siguientes apartados. En el tercer capítulo se presenta el diseño y optimización de un nanodispositivo para la detección de la bacteria Mycoplasma fermentans. En primer lugar, los poros de una placa de alúmina mesoporosa se cargan con un indicador fluorescente (rodamina B). Seguidamente, la superficie es funcionalizada con una secuencia de ADN complementaria a una región altamente conservada de la subunidad ribosomal 16S de la bacteria Mycoplasma fermentans. El impedimento estérico generado por las secuencias de ADN ancladas al exterior de los poros impide la salida del indicador encapsulado. Únicamente en presencia de DNA de la bacteria Mycoplasma fermentans, se produce la apertura de los poros permitiéndose la difusión de la carga (rodamina B) que es posteriormente medida mediante espectroscopía de fluorescencia. En el capítulo cuatro se diseña de un nanodispositivo capaz de detectar de forma rápida, sensible y selectiva la bacteria Staphylococcus aureus. Para la preparación del material sensor, un soporte de alúmina mesoporosa es, en primer lugar, cargado con el indicador fluorescente rodamina B. A continuación, los poros del soporte son tapados mediante el anclaje de un aptámero que reconoce de forma específica la bacteria. Solamente en presencia de Staphylococcus aureus se produce la liberación del indicador encapsulado, que es posteriormente medido mediante espectroscopía de fluorescencia. Además, la respuesta obtenida es específica para Staphylococcus aureus. Este sistema ha sido ensayado en muestras reales. En el sexto capítulo, diseña un nanodispositivo híbrido orgánico-inorgánico consistente en un material de alúmina mesoporosa cubierto con una secuencia de ADN específica para la detección de ADN del hongo Pneumocystis jirovecii. En este caso, el soporte de alúmina cargado con rodamina B se recubre con una secuencia de ADN específica para el reconocimiento de este hongo. En presencia del organismo, la horquilla hibrida con el ADN del hongo, lo que resulta en una conformación triplex con elevada afinidad y estabilidad que induce, al mismo tiempo, el desplazamiento de este complejo de la superficie. Como consecuencia de este reconocimiento la carga se libera y es cuantificada mediante espectroscopía de fluorescencia. El sistema ha sido satisfactoriamente validado. En el séptimo capítulo, se diseña un sistema sensor con la capacidad de detectar gluten de forma rápida y sencilla en extractos de alimentos procesados y no procesados. Para ello, un soporte de alúmina mesoporosa se carga con rodamina B y los poros se recubren con un aptámero específicamente diseñado para la detección de la proteína gliadina, que constituye el 50 % del total del clúster de elementos que forman el gluten. La elevada afinidad y especificidad entre el aptámero y la proteína en cuestión hacen que en presencia de ésta se produzca un desplazamiento de la puerta molecular que permite la difusión del colorante encapsulado que es finalmente monitorizado mediante espectroscopía de fluorescencia. Finalmente, en el capítulo octavo se discuten de forma conjunta los resultados obtenidos en los capítulos anteriores y la potencial aplicación de los sistemas desarrollados en el actual sistem / [CA] La present tesi doctoral, titulada "New nanostructured supports with signal amplification features for the detection of molecules and biomolecules of interest", es centra en el disseny i preparació de nous materials híbrids orgànics-inorgànics constituïts per portes moleculars suportades sobre alúmina mesoporosa amb l'objectiu de desenvolupar nous sistemes sensors amb potencials aplicacions en el camp de la diagnosi i del control alimentari. En el primer capítol de la tesi s'introdueixen els conceptes en què estan basats els estudis realitzats i els materials preparats. A continuació, en el segon capítol es descriuen els objectius generals de la tesi que seran abordats en els següents apartats. En el tercer capítol es presenta el disseny i optimització d'un nanodispositiu per a la detecció de la bactèria Mycoplasma fermentans. Primerament, els porus d'una placa d'alúmina mesoporosa són carregats amb un indicador fluorescent (rodamina B). Seguidament, la superfície és funcionalitzada amb una seqüència d'ADN complementaria a una regió altament conservada de la subunitat ribosomal 16S de la bactèria Mycoplasma fermentans. L'impediment estèric generat per les seqüències d'ADN ancorades a l'exterior dels porus impedeix l'alliberament de l'indicador encapsulat. Únicament en presencia d'ADN de la bactèria Mycoplasma fermentans, es produeix l'obertura dels porus permetent la difusió de la càrrega (rodamina B) que és posteriorment mesurada mitjançant fluorescència. En el capítol quatre es dissenya un nanodispositiu capaç de detectar de forma ràpida, sensible i selectiva la bactèria Staphylococcus aureus. Per a la preparació del material sensor, el suport d'alúmina mesoporosa és, primerament, carregat amb l'indicador fluorescent rodamina B. A continuació, els porus del suport són tapats mitjançant l'ancoratge d'un aptàmer que reconeix de forma específica a la bactèria. Solament en presència de Staphylococcus aureus es produeix l'alliberament de l'indicador encapsulat, que és posteriorment mesurat mitjançant espectroscòpia de fluorescència. A més a més, la resposta obtinguda és específica per Staphylococcus aureus. Aquest sistema ha sigut validat amb mostres reals de pacients. En el sisè capítol, es dissenya un nanodispositiu híbrid orgànic-inorgànic consistent en un material d'alúmina mesoporosa cobert amb una seqüència d'ADN específica per a la detecció de l'ADN del fong Pneumocystis jirovecii. En aquest cas, el suport d'alúmina carregat amb l'indicador fluorescent rodamina B és recobert amb una seqüència d'ADN específica per al reconeixement d'aquest fong. En presència de l'organisme, la forquilla hibrida amb l'ADN del fong, resultant en una conformació triplex amb elevada afinitat i estabilitat, que indueix, al mateix temps, el desplaçament d'aquest complex de la superfície. Com a conseqüència d'aquest reconeixement la càrrega és alliberada i quantificada mitjançant espectroscòpia de fluorescència. El sistema ha sigut validat com a mètode diagnòstic mitjançant l'anàlisi de mostres reals de pacients. En el seté capítol, es dissenya un sistema sensor amb la capacitat de detectar gluten de forma ràpida i senzilla en extractes d'aliments processats i no processats. Per a això, un suport d'alúmina mesoporosa es carrega amb indicador fluorescent rodamina B i posteriorment és recobert amb un aptàmer específicament dissenyat per a la detecció de la proteïna gliadina, que constitueix el 50 % del total del clúster d'elements que formen el gluten. L'elevada afinitat i especificitat entre l'aptàmer i la proteïna en qüestió fa que en presència d'aquesta es produesca un desplaçament de la porta molecular que permet la difusió de la càrrega encapsulada i que serà finalment monitoritzada mitjançant espectroscòpia de fluorescència. Finalment, en el capítol vuité es discuteixen de manera conjunta els result / [EN] The PhD thesis hereby presented and entitled "New nanostructured supports with signal amplification features for the detection of molecules and biomolecules of interest", focuses in the design and preparation of new hybrid organic-inorganic materials constituted by molecular gates supported over mesoporous alumina with the aim of developing new sensor probes of potential applications in the fields of diagnosis and food control. In the first chapter, the concepts in which studies and prepared materials are based, are introduced. Next, the second chapter describes the general objectives of this thesis, which will be approached in the following sections. In the third chapter, it is presented in detail the design and optimization process of a nanodevice applied for the detection of Mycoplasma fermentans bacterium. First of all, mesoporous alumina porous films are charged with a fluorescent indicator (rhodamine B). Then, the surface is functionalized with a DNA sequence complementary to a highly conserved region of the 16S ribosomal subunit of the bacterium Mycoplasma fermentans. Steric hindrance generated by DNA sequences on the surface inhibits the release of the encapsulated indicator. Only in the presence of bacterium Mycoplasma fermentans DNA, molecular gates open, allowing payload diffusion to the solution, which is measured by fluorescence spectroscopy. In chapter four, it is carried out the design and optimization of a nanodevice able to detect Staphylococcus aureus bacterium in a fast, sensitive and selective way. For the sensor preparation, alumina mesoporous support is, first, loaded with the rhodamine B fluorescent dye. Then, the mesoporous are blocked through the attachment of an aptamer that recognises specifically this bacterium. Exclusively in the presence of Staphylococcus aureus it is accomplished the release of the encapsulated dye, which is later monitored by fluorescence spectroscopy. The response obtained is specific for Staphylococcus aureus. This system has been validated in real samples. In the sixth chapter, it is detailed the design and optimization process of a hybrid organic-inorganic nanodevice based on a capped mesoporous alumina material for the detection of Pneumocystis jirovecii fungus DNA. In this case, the mesoporous alumina support is loaded with a fluorescent dye and decorated with a specific oligonucleotide sequence designed for the recognition of Pneumocystis fungus. In the presence of the target organism, the fork-like oligonucleotide hybridises with the DNA of the fungus, which results in the adoption of a triplex conformation with high affinity and stability that induces, at the same time, the displacement of this complex from the surface. Consequently, the payload diffused to the solution is quantified through fluorescence spectroscopy. The system has been successfully validated. In the seventh chapter, it was developed a sensor system for gluten detection, in a quick and easy way, in processed and non-processed food extracts. For this, a mesoporous alumina support is loaded with the fluorescent dye rhodamine B, and later was functionalized with an aptamer specifically designed for the detection of gliadin, a protein that constitutes 50 % of average cluster elements that forms gluten. The protein-aptamer high affinity and specificity induce the displacement of the capping aptamer and cargo delivery, which is monitored through fluorescence spectroscopy. Finally, in the eighth chapter, the results obtained in the previous chapters and the potential application of the systems developed as health and food control system are discussed. / We thank the Spanish Government projects MAT2015-64139-C4-1-R, AGL2015-70235-C2-2-R, and TEC2015-71324-R (MINECO/FEDER, UE), the Generalitat Valenciana (project PROMETEOII/2014/047), the Catalan authority (project AGAUR 2014SGR1344), and ICREA under the 2014 ICREA Academia Award for support. This study was supported by the Spanish Government projects RTI2018-100910-B-C41 and SAF2017-82251-R (MCUI/AEI/FEDER, UE), the Generalitat Valenciana (project PROMETEO/2018/024), the Universitat Politècnica de València−Instituto de Investigación Sanitaria La Fe (B02-MIRSA project), CIBER-BBN (NANOPATH and valorization project CANDI-EYE) and co-financed by the EU through the Valencian Community ERDF PO 2014-2020. This research was funded by the Spanish Government, projects RTI2018-100910-B-C41 (MCUI/AEI/FEDER, UE) and CTQ2017-84415-R / Pla Blasco, L. (2021). New nanostructured supports with signal amplification features for the detection of molecules and biomolecules of interest [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/166500 / TESIS

Ce travail de thèse a consisté à améliorer certaines propriétés de revêtements fonctionnels à base de polychlorure de vinyle (PVC) plastifié et de polyamide-imide (PAI) par incorporation de nanocharges inorganiques préformées, lamellaires ou divisées. La compatibilisation des nanocharges avec la matrice dans laquelle elles ont été incorporées s’est avérée indispensable pour obtenir des films nanocomposites avec une distribution homogène et un état de dispersion le plus fin possible. Différentes stratégies de compatibilisation ont été étudiées, comme la physisorption, la chimisorption, l’intercalation ou encore la chélation d’agents compatibilisants judicieusement choisis et adaptés à chacun des systèmes. Les nouvelles nanocharges ainsi modifiées ont été caractérisées en vue de leur introduction dans la matrice. Les films nanocomposites « compatibilisés » ont été élaborés en voie solvant et/ou par polymérisation in-situ, suivie d’une gélification physique pour le PVC ou d’une réticulation chimique pour le PAI. La caractérisation morphologique des films, réalisée par DRX et MEB/MET, ainsi que les propriétés thermiques et thermomécaniques des films, évaluées par ATG, DSC et DMA, mettent en évidence l’importance de deux paramètres : la chimie de surface des nanocharges, à l’origine des interactions interfaciales nanocharge/polymère, et le procédé d’élaboration du nanocomposite. / This study aims at improving some properties of functional PVC- and PAI- based coatings by adding preformed inorganic lamellar or spherical nanofillers. The compatibilization of nanofiller with the polymer matrix in which they are introduced, is required in order to obtain nanocomposite films with an homogeneous distribution and a dispersion state as fine as possible. Different compatibilization strategies, well-suited for each system, have been studied: compatibilizer physisorption, chemisorption, intercalation or chelation. The new modified nanofillers have been characterized before their introduction into the matrix. Various strategies have been considered to obtain the “compatibilized” nanocomposite films such as the solution mixing and/or the in-situ polymerization, followed by a physical gelation or curing step for PVC- or PAI-based nanocomposites, respectively. The morphological characterization of the films, through XRD and SEM/TEM analysis, and the thermal and thermomecanical properties, evaluated by TGA, DSC and DMA, underlined the importance of two parameters: the nanofiller surface chemistry, responsible for the nanofiller/polymer interfacial interactions, and the elaboration process of the nanocomposite.

Coal refuse and combustion byproducts as industrial solid waste stockpiles have become great threats to the environment. Recycling is one practical solution to utilize this huge amount of solid waste through activation as substitute for ordinary Portland cement. The central goal of this dissertation is to investigate and develop a new silica-alumina based cementitious material largely using coal refuse as a constituent that will be ideal for durable construction, mine backfill, mine sealing and waste disposal stabilization applications. This new material is an environment-friendly alternative to ordinary Portland cement. The main constituents of the new material are coal refuse and other coal wastes including coal sludge and coal combustion products (CCPs). Compared with conventional cement production, successful development of this new technology could potentially save energy and reduce greenhouse gas emissions, recycle vast amount of coal wastes, and significantly reduce production cost. A systematic research has been conducted to seek for an optimal solution for enhancing pozzolanic reactivity of the relatively inert solid waste-coal refuse in order to improve the utilization efficiency and economy benefit for construction and building materials. The results show that thermal activation temperature ranging from 20°C to 950°C significantly increases the workability and pozzolanic property of the coal refuse. The optimal activation condition is between 700°C to 800°C within a period of 30 to 60 minutes. Microanalysis illustrates that the improved pozzolanic reactivity contributes to the generated amorphous materials from parts of inert aluminosilicate minerals by destroying the crystallize structure during the thermal activation. In the coal refuse, kaolinite begins to transfer into metakaol in at 550°C, the chlorite minerals disappear at 750°C, and muscovite 2M 1 gradually dehydroxylates to muscovite HT. Furthermore, this research examines the environmental acceptance and economic feasibility of this technology and found that this silica alumina-based cementitious material not only meets EPA requirements but also shows several advantages in industrial application.

Indiana University-Purdue University Indianapolis (IUPUI) / Provisional restorative treatment is an essential part of fixed prosthodontics. Incorporation of adequately constructed provisional restorations will enhance the success rate of definitive restorations. Repairing or replacing failed provisional restorations is a concern for both clinicians and patients. The objective of this investigation was to study the effects of alumina nanofibers reinforcement on the mechanical properties of commercially available provisional fixed partial denture PMMA material. The hypothesis was that the addition of alumina nanofibers to commercially available PMMA resin will significantly increase its flexural strength, fracture toughness, and microhardness. Alumina nanofibers at 0.0 wt %, 0.5 wt %, 1.0 wt %, and 2.5 wt % were added to commercially available provisional fixed partial material (Jet Tooth Shade). A quaternary ammonium acetate dispersant (CC-59, Goldschmidt, Janesville, WI) was added to the acrylic monomer at 0.0 wt %, 1.0 wt %, 2.0 wt % and 5.0 wt % of the nanofiber weight (12 test groups, 1 control). Samples from each group were evaluated for flexural strength, flexural modulus, fracture toughness, and microhardness. The samples were tested after storing in distilled water for 24 hours and 7 days at 37ºC. Two-way analysis of variance (ANOVA) was used to test the effects of storage time and combinations of alumina nanofiber level and quaternary ammonium acetate dispersant level on the flexural strength, fracture toughness, and microhardness of the provisional PMMA resin. Pair-wise comparisons between groups were performed using Tukey’s multiple comparisons procedure to control the overall significance level at 5 percent. Three fracture toughness samples/group were randomly selected for Energy Dispersive Spectrometry (EDS) to qualitatively evaluate the dispersion of the fibers. The data obtained from this study showed that control sample values were in the acceptance range compared with previous research. The experimental samples did not reinforce the provisional resin in the flexural strength, modulus, fracture toughness, or microhardness. There are several factors may attribute to these results, such as poor bonding at the filler/matrix interface. The more homogeneous the mixture of PMMA and fiber, the stronger the acrylic resin. In fact, the presence of poorly bonded fibers, to which little load is transferred, can be almost equivalent to voids. In addition, as seen with EDS images, alumina nanofibers had a tendency to agglomerate. The use of a magnetic stirrer was not effective in physically separating nanofibers agglomerates. Direct dispersion of alumina nanofibers in methyl methacrylate monomer and quaternary ammonium acetate dispersant was not effective in separating the nanofibers into nano-scaled single crystals. The presence of fiber agglomerates acts as a structural defect that detrimentally affects the mechanical properties. Further studies are needed to evaluate the effectiveness of fibers, dispersion techniques, and coupling agents to enhance the mechanical properties of the provisional PMMA resin.

No description available.

Recent advances in nanoscience and technology have provided the scientific community with new exciting opportunities to rationally design and fabricate materials at the nanometer scale with drastically different properties as compared to their bulk counterparts. A variety of challenges related to nanoparticle (NP) synthesis and materials characterization have been tackled , allowing us to make more homogenous, well defined, size- and shape-selected NPs, and to probe deeper and more comprehensively into their distinct properties. In this dissertation, a variety of phenomena relevant to nanosized materials are investigated, including the thermal stability of NPs and coarsening phenomena in different environments, the experimental determination of NP shapes, gaining insight into NP-support interactions, epitaxial relationships, and unusual thermodynamic and electronic properties of NPs, including the effect of adsorbates on the electron density of states of small clusters, and the chemical, and structural evolution of NPs under reaction conditions. In chapter 2, a general description of different characterization tools that are used in this dissertation is provided. In chapter 3, the details of two different methods used for NP synthesis, namely inverse micelle encapsulation and physical vapor deposition (PVD) are described. Chapter 4 describes the thermal stability and coarsening behavior of Pt NPs supported on TiO2(110) and γ-Al2O3 as a function of the synthesis method, support pretreatment, and annealing environment. For the Pt/TiO2(110) system, micellesynthesized NPs showed remarkable stability against coarsening for annealing temperatures up to 1060°C in vacuum, in contrast to PVD-grown NPs. When comparing v different annealing environments (H2, O2, H2O), Pt NPs on γ-Al2O3 annealed in O2 were found to be the least affected by coarsening, followed by those heated in H2O vapor. The largest NP growth was observed for the sample annealed in H2. The role of the PtOx species formed under oxidizing conditions will be discussed. In chapter 5, the shape of Pt and Au NPs and their epitaxial relationship with the TiO2(110) support was extracted from scanning tunneling microscopy (STM) measurements. Three main categories of NP shapes were identified, and through shape modeling, the contribution of facets with different orientations was obtained as a function of the number of atoms in each NP. It was also shown that the micellesynthesized Pt and Au NPs have an epitaxial relationship with the support, which is evident from the fact that they always have one symmetry axis parallel to TiO2(110) atomic rows in [001] directions. Chapter 6 describes how the presence of NPs on TiO2(110) surface affects its reconstruction upon high temperature annealing in vacuum. In contrast to NP-free TiO2(110) substrates, long and narrow TiO2 stripes are observed for Pt NP-decorated surfaces. This phenomenon is explained based on the stabilization of TiO2, induced by Pt NPs, which hinders the desorption of oxygen atoms in TiO2 to vacuum. In chapter 7, a systematic investigation of the thermodynamic properties of γ- Al2O3-supported Pt NPs and their evolution with decreasing NP size is presented. A combination of in situ extended x-ray absorption fine structure spectroscopy (EXAFS), ex situ transmission electron microscopy (TEM) measurements, and NP shape modeling is used to obtain the NPs shape, thermal expansion coefficient, and Debye vi temperature. The unusual thermodynamic behavior of these NPs such as their negative thermal expansion and enhanced Debye temperature are discussed in detail. Chapter 8 presents an investigation of the electronic properties of size-controlled γ-Al2O3-supported Pt NPs and their evolution with decreasing NP size and adsorbate (H2) coverage. The hydrogen coverage of Pt NPs at different temperatures was estimated based on XANES data and was found to be influenced by the NP size, and shape. In addition, correlations between the shift in the center of the unoccupied d-band density of states (theory) and energy shifts of the XANES spectra (experiment) upon hydrogen chemisorption as well as upon modification of the NP structure were established. Chapter 9 is dedicated to an operando study, describing the evolution of the structure and oxidation state of ZrO2-supported Pd nanocatalysts during the in-situ selective reduction of NO in H2 via EXAFS and XANES measurements.

Carbon-bonded alumina filters and their binders, lactose, tannin and CarboresP, were investigated by Raman spectroscopy. Special emphasis was placed on the pyrolysis study of the binders. In situ measurements were performed on the tannins gallic acid, ellagic acid and tannic acid to determine the pyrolysis temperatures and products. Furthermore, the binder samples fired in a reducing atmosphere in a coke bed were analyzed by Raman spectroscopy and their transition from an amorphous carbon system to nanocrystalline graphite was observed. The influence of different binders on the carbon-bound alumina filters was studied, as well as the influence of different additives. However, no significant difference was observed between samples with different binder compositions or with additives. In addition, Raman measurements on the spinel MgAlON indicate an increased disorder of the structure due to the incorporated nitrogen.

No description available.