The large unlicensed 3 GHz overlapping bandwidth that is available worldwide at 60 GHz has resulted in renewed interest in 60 GHz technology. This frequency band has made it attractive for short-range gigabit wireless communication. The power amplifier (PA) directly influences the performance and quality of this entire communication chain, as it is one of the final subsystems in the transmitter. Spectral efficient modulation schemes used at 60 GHz pose challenging requirements for the linearity of the PA. To improve the linearity, several external linearisation techniques currently exist, such as feedback, feedforward, envelope elimination and restoration, linear amplification with non-linear components and predistortion. This thesis is aimed at investigating and characterising the distortion components found in PAs at mm-wave frequencies and evaluating whether an adaptive predistortion (APD) linearisation technique is suitable to reduce these distortion components. After a thorough literature study and mathematical analysis, it was found that the third-order intermodulation distortion (IMD3) components were the most severe distortion components. Predistortion was identified as the most effective linearisation technique in terms of minimising these IMD3 components and was therefore proposed in this research. It does not introduce additional complexity and can easily be integrated with the PA. Furthermore, the approach is stable and has lower power consumption when compared to the aforementioned linearisation techniques. The proposed predistortion technique was developed compositely through this research by making it a function of the PA’s output power that was measured using a power detector. A comparator was used with the detected output power and the reference voltages to control the dynamic bias circuit of the variable gain amplifier. This provided control and flexibility on when to apply the predistortion to the PA and therefore allowing the linearity of the PA to be optimised. Three-stage non-linear and linear PAs were also designed at 60 GHz and implemented to compare the performance of the APD technique and form part of the hypothesis verification process. The 130 nm silicon-germanium (SiGe) bipolar and complementary metal oxide semiconductor (BiCMOS) technology from IBM was used for the simulation of the entire APD and PA design and for the fabrication of the prototype integrated circuits (ICs). This technology has the advantage of integrating the high performance, low power intensive SiGe heterojunction bipolar transistors (HBTs) with the CMOS technology. The SiGe HBTs have a high cut-off frequency (fT > 200 GHz), which is ideal for mm-wave PA applications and the CMOS components were integrated in the control logic of the digital circuitry. The simulations and IC layout were accomplished with Cadence Virtuoso. The implemented IC occupies an area of 1.8 mm by 2.0 mm. The non-linear PA achieves a Psat of 11.97 dBm and an IP1dB of -10 dBm. With the APD technique applied, the linearity of the PA is significantly improved with an IP1dB of -6 dBm and an optimum IMD3 reduction of 10 dB. Based on the findings and results of the applied APD technique, APD reduced intermodulation distortion (especially the IMD3) and is thus suitable to improve the linearity of PAs at mm-wave frequencies. To the knowledge of this author, no APD technique has been applied for PAs at 60 GHz, therefore the contribution of this research will assist future PA designers to characterise and optimise the reduction of the IMD3 components. This will result in improved linear output power from the PA and the use of complex modulation schemes at 60 GHz. / Thesis (PhD)--University of Pretoria, 2014. / Electrical, Electronic and Computer Engineering / PhD

No description available.

Le travail porte sur le développement et l’optimisation de transistors bipolaires à hétérojonction (TBH) SiGe et SiGeC par conception technologique assistée par ordinateur (TCAD). L'objectif est d'aboutir à un dispositif performant réalisable technologiquement, en tenant compte de tous les paramètres : étapes de fabrication technologiques, topologie du transistor, modèles physiques. Les études menées permettent d’atteindre les meilleures performances, en particulier une amélioration importante de la fréquence maximale d’oscillation (fMAX). Ce travail est la première approche développée pour la simulation des TBH SiGeC qui prend en compte l'impact de la contrainte et de la teneur en germanium et en carbone dans la base; conjointement pour les simulations des procédés de fabrication et les simulations électriques.Pour ce travail, nous avons développé et implémenté dans le simulateur TCAD des méthodes d'extraction de fMAX prenant en compte les éléments parasites intrinsèques et extrinsèques. Nous avons développé et implémenté un modèle pour la densité effective d’états fonction de la teneur en germanium et en carbone dans la base. Les modèles pour la bande interdite, la mobilité et le temps de relaxation de l'énergie sont calibrés sur la base de simulations Monte-Carlo.Les différentes analyses présentées dans cette thèse portent sur six variantes technologiques de TBH. Trois nouvelles architectures de TBH SiGeC avancés ont été élaborées et proposées pour des besoins basse et haute performance. Grace aux résultats obtenus, le meilleur compromis entre les différents paramètres technologiques et dimensionnels permettent de fabriquer un TBH SiGeC avec une valeur de fMAX de 500 GHz, réalisant ainsi l’objectif principal de la thèse. / The present work investigates the technology development of state-of-the-art SiGe and SiGeC Heterojunction Bipolar Transistors (HBT) by means of technology computer aided design (TCAD). The objective of this work is to obtain an advanced HBT very close to the real device not only in its process fabrication steps, but also in its physical behavior, geometric architecture, and electrical results. This investigation may lead to achieve the best electrical performances for the devices studied, in particular a maximum operating frequency of 500 GHz. The results of this work should help to obtain more physical and realistic simulations, a better understanding of charge transport, and to facilitate the development and optimization of SiGe and SiGeC HBT devices.The TCAD simulation kits for SiGe/SiGeC HBTs developed during our work have been carried out in the framework of the STMicroelectronics bipolar technology evolution. In order to achieve accurate simulations we have used, developed, calibrated and implemented adequate process models, physical models and extraction methodologies. To our knowledge, this work is the first approach developed for SiGe/SiGeC HBTs which takes into account the impact of the strain, and of the germanium and carbon content in the base, for both: process and electrical simulations.In this work we will work with the successive evolutions of B3T, B4T and B5T technologies. For each new device fMAX improves of 100 GHz, thus the technology B3T matches to 300 GHz, B4T and B5T to 400 and 500 GHz, respectively.Chapter one introduces the SiGe SiGeC heterojunction bipolar technologies and their operating principles. This chapter deals also with the high frequency AC transistor operation, the extraction methods for fMAX and the carrier transport in extremely scaled HBTs.Chapter two analyzes the physical models adapted to SiGeC strained alloys used in this work and the electrical simulation of HBT devices. This is also an important work of synthesis leading to the selection, implementation and development of dedicated models for SiGeC HBT simulation.Chapter three describes the B3T TCAD simulation platform developed to obtain an advanced HBT very close to the real device. In this chapter the process fabrication of the B3T technology is described together with the methodology developed to simulate advanced HBT SiGeC devices by means of realistic TCAD simulations.Chapter four describes the HBT architectures developed during this work. We will propose low-cost structures with less demanding performance requirements and highly performing structures but with a higher cost of production. The B4T architecture which has been manufactured in clean-room is deeply studied in this chapter. The impact of the main fabrication steps is analyzed in order to find the keys process parameters to increase fMAX without degrading other important electrical characteristics. At the end of this chapter the results obtained is used to elaborate a TCAD simulation platform taking into account the best trade-off of the different key process parameters to obtain a SiGeC HBT working at 500 GHz of fMAX.

No description available.

This thesis deals with the main aspects in chemical vapordeposition (CVD) of silicon (Si) and silicon-germanium (Si1-xGex) films for high-speed bipolar transistors.In situdoping of polycrystalline silicon (poly-Si)using phosphine (PH3) and disilane (Si2H6) in a low-pressure CVD reactor was investigated toestablish a poly-Si emitter fabrication process. The growthkinetics and P incorporation was studied for amorphous Si filmgrowth. Hydrogen (H) incorporated in the as-deposited films wasrelated to growth kinetics and the energy for H2desorption was extracted. Film properties such asresistivity, mobility, carrier concentration and grain growthwere studied after crystallization using either furnaceannealing or rapid thermal annealing (RTA). In order tointegrate an epitaxial base, non-selective epitaxial growth(NSEG) of Si and SiGe in a lamp-heated single-waferreduced-pressure CVD reactor was examined. The growth kineticsfor Si epitaxy and poly-Si deposition showed a differentdependence on the deposition conditions i.e. temperature andpressure. The growth rate difference was mainly due to growthkinetics rather than wafer surface emissivity effects. However,it was observed that the growth rate for Si epitaxy and poly-Sideposition was varying during growth and the time-dependencewas attributed to wafer surface emissivity variations. A modelto describe the emissivity effects was established, taking intoconsideration kinetics and the reactor heating mechanisms suchas heat absorption, emission andconduction. Growth ratevariations in opening of different sizes (local loading) andfor different oxide surface coverage (global loading) wereinvestigated. No local loading effects were observed, whileglobal loading effects were attributed to chemical as well astemperature effects. Finally, misfit dislocations formed in theSiGe epitaxy during NSEG were found to originate from theinterface between the epitaxial and polycrystalline regions.The dislocations tended to propagate across the activearea. <b>Keywords:</b>chemical vapor deposition (CVD), bipolarjunction transistor (BJT), heterojunction bipolar transistor(HBT), silicon-germanium (SiGe), epitaxy, poly-Si emitter,in situdoping, non-selective epitaxy (NSEG), loadingeffect, emissivity effect

Heterojunction bipolar transistors (HBT) based on SiGeC havebeen investigated. Two high-frequency architectures have beendesigned, fabricated and characterized. Different collectordesigns were applied either by using selective epitaxial growthdoped with phosphorous or by non-selective epitaxial growthdoped with arsenic. Both designs have a non-selectivelydeposited SiGeC base doped with boron and a poly-crystallineemitter doped with phosphorous. Selective epitaxial growth of the collector layer has beendeveloped by using a reduced pressure chemical vapor deposition(RPCVD) technique. The incorporation of phosphorous and defectformation during selective deposition of these layers has beenstudied. A major problem of phosphorous-doping during selectiveepitaxy is segregation. Different methods, e.g. chemical orthermal oxidation, are shown to efficiently remove thesegregated dopants. Chemical-mechanical polishing (CMP) hasalso been used as an alternative to solve this problem. The CMPstep was successfully integrated in the HBT process flow. Epitaxial growth of Si1-x-yGexCy layers for base layerapplications in bipolar transistors has been investigated indetail. The optimization of the growth parameters has beenperformed in order to incorporate carbon substitutionally inthe SiGe matrix without increasing the defect density in theepitaxial layers. The thermal stability of npn SiGe-based heterojunctionstructures has been investigated. The influence of thediffusion of dopants in SiGe or in adjacent layers on thethermal stability of the structure has also been discussed. SiGeC-based transistors with both non-selectively depositedcollector and selectively grown collector have been fabricatedand electrically characterized. The fabricated transistorsexhibit electrostatic current gain values in the range of 1000-2000. The cut-off frequency and maximum oscillation frequencyvary from 40-80 GHz and 15-30 GHz, respectively, depending onthe lateral design. The leakage current was investigated usinga selectively deposited collector design and possible causesfor leakage has been discussed. Solutions for decreasing thejunction leakage are proposed. <b>Key words:</b>Silicon-Germanium-Carbon (SiGeC),Heterojunction bipolar transistor (HBT), chemical vapordeposition (CVD), selective epitaxy, non-selective epitaxy,collector design, high-frequency measurement, dopantsegregation, thermal stability.

This work investigates the challenges associated with designing silicon-germanium (SiGe) analog and mixed-signal circuits capable of operating reliably in extreme environment conditions. Three extreme environment operational conditions, namely, operation over an extremely wide temperature range, operation at extremely low temperatures, and operation under radiation exposure, are considered. As a representative for critical analog building blocks, bandgap voltage reference (BGR) circuit is chosen. Several architectures of the BGRs are implemented in two SiGe BiCMOS technology platforms. The effects of wide-temperature operation, deep cryogenic operation, and proton and x-ray irradiation on the performance of BGRs are investigated. The impact of Ge profile shape on BGR's wide-temperature performance is also addressed. Single-event transient response of the BGR circuit is studied through microbeam experiments. In addition, proton radiation response of high-voltage transistors, implemented in a low-voltage SiGe platform, is investigated. A platform consisting of a high-speed comparator, digital-to-analog (DAC) converter, and a high-speed flash analog-to-digital (ADC) converter is designed to facilitate the evaluation of the extreme environment capabilities of SiGe data converters. Room temperature measurement results are presented and predictions on how temperature and radiation will impact their key electrical properties are provided.

No description available.

<p>This thesis deals with the main aspects in chemical vapordeposition (CVD) of silicon (Si) and silicon-germanium (Si_1-xGe_x) films for high-speed bipolar transistors.<i>In situ</i>doping of polycrystalline silicon (poly-Si)using phosphine (PH₃) and disilane (Si₂H₆) in a low-pressure CVD reactor was investigated toestablish a poly-Si emitter fabrication process. The growthkinetics and P incorporation was studied for amorphous Si filmgrowth. Hydrogen (H) incorporated in the as-deposited films wasrelated to growth kinetics and the energy for H₂desorption was extracted. Film properties such asresistivity, mobility, carrier concentration and grain growthwere studied after crystallization using either furnaceannealing or rapid thermal annealing (RTA). In order tointegrate an epitaxial base, non-selective epitaxial growth(NSEG) of Si and SiGe in a lamp-heated single-waferreduced-pressure CVD reactor was examined. The growth kineticsfor Si epitaxy and poly-Si deposition showed a differentdependence on the deposition conditions i.e. temperature andpressure. The growth rate difference was mainly due to growthkinetics rather than wafer surface emissivity effects. However,it was observed that the growth rate for Si epitaxy and poly-Sideposition was varying during growth and the time-dependencewas attributed to wafer surface emissivity variations. A modelto describe the emissivity effects was established, taking intoconsideration kinetics and the reactor heating mechanisms suchas heat absorption, emission andconduction. Growth ratevariations in opening of different sizes (local loading) andfor different oxide surface coverage (global loading) wereinvestigated. No local loading effects were observed, whileglobal loading effects were attributed to chemical as well astemperature effects. Finally, misfit dislocations formed in theSiGe epitaxy during NSEG were found to originate from theinterface between the epitaxial and polycrystalline regions.The dislocations tended to propagate across the activearea.</p><p><b>Keywords:</b>chemical vapor deposition (CVD), bipolarjunction transistor (BJT), heterojunction bipolar transistor(HBT), silicon-germanium (SiGe), epitaxy, poly-Si emitter,<i>in situ</i>doping, non-selective epitaxy (NSEG), loadingeffect, emissivity effect</p>

<p>Heterojunction bipolar transistors (HBT) based on SiGeC havebeen investigated. Two high-frequency architectures have beendesigned, fabricated and characterized. Different collectordesigns were applied either by using selective epitaxial growthdoped with phosphorous or by non-selective epitaxial growthdoped with arsenic. Both designs have a non-selectivelydeposited SiGeC base doped with boron and a poly-crystallineemitter doped with phosphorous.</p><p>Selective epitaxial growth of the collector layer has beendeveloped by using a reduced pressure chemical vapor deposition(RPCVD) technique. The incorporation of phosphorous and defectformation during selective deposition of these layers has beenstudied. A major problem of phosphorous-doping during selectiveepitaxy is segregation. Different methods, e.g. chemical orthermal oxidation, are shown to efficiently remove thesegregated dopants. Chemical-mechanical polishing (CMP) hasalso been used as an alternative to solve this problem. The CMPstep was successfully integrated in the HBT process flow.</p><p>Epitaxial growth of Si1-x-yGexCy layers for base layerapplications in bipolar transistors has been investigated indetail. The optimization of the growth parameters has beenperformed in order to incorporate carbon substitutionally inthe SiGe matrix without increasing the defect density in theepitaxial layers.</p><p>The thermal stability of npn SiGe-based heterojunctionstructures has been investigated. The influence of thediffusion of dopants in SiGe or in adjacent layers on thethermal stability of the structure has also been discussed.</p><p>SiGeC-based transistors with both non-selectively depositedcollector and selectively grown collector have been fabricatedand electrically characterized. The fabricated transistorsexhibit electrostatic current gain values in the range of 1000-2000. The cut-off frequency and maximum oscillation frequencyvary from 40-80 GHz and 15-30 GHz, respectively, depending onthe lateral design. The leakage current was investigated usinga selectively deposited collector design and possible causesfor leakage has been discussed. Solutions for decreasing thejunction leakage are proposed.</p><p><b>Key words:</b>Silicon-Germanium-Carbon (SiGeC),Heterojunction bipolar transistor (HBT), chemical vapordeposition (CVD), selective epitaxy, non-selective epitaxy,collector design, high-frequency measurement, dopantsegregation, thermal stability.</p>