Concentrating Solar Power (CSP) is one of the most promising renewable energybased electricity generation technologies to deal with the increasing demand of power consumption and environmental sustainability. With the aim of achieving the 2020 SunShot cost target for CSP of 60 USD/MWh, the United States Department of Energy presented, in May 2018, the Gen3 CSP initiative. In particular, the CSP Gen3 Liquid-Phase Pathway proposes to design a CSP system adopting liquid sodium as Heat Transfer Fluid (HTF) in the receiver, advanced high-temperature molten chloride salt as storage fluid and supercritical CO2 (sCO2) Brayton cycle as power cycle. Within this framework, the aim of this master thesis was to design the sodium-chloride salt Heat Exchanger (HX) by developing both a heat exchanger model and a sodiumsalt-sCO2 system model. To pursue these purposes, a completely new Modelica-based HX model was developed and added to the SolarTherm library. Furthermore, as an extension of earlier models, the sodium-salt-sCO2 CSP system (NaSaltsCO2System) was implemented in SolarTherm, by incorporating the HX model and linking it with other new and existing component models. As for the HX, a general model was developed for shell and tube heat exchangers, based on the TEMA guidelines, with the possibility of being customized in terms of media adopted, constraints, boundary conditions, and correlations. The model performs an optimization in order to select the internal geometry configuration that optimizes a user-defined objective-function. By employing the implemented HX model in the NaSaltsCO2System, the sodium-salt heat exchanger was designed aiming at minimizing the Levelized Cost of Electricity (LCOE), providing a complete geometry description, and an estimation of the performances and costs. The resulting NaSaltsCO2System model was found to be robust and able to perform annual simulations that allowed to estimate the energy performances of the CSP plant, as well as the LCOE. Considering the sodium-salt-sCO2 CSP system characterized by a receiver capacity of 543 MWth, 12 hours of Thermal Energy Storage (TES), and a 100 MWe power block, the LCOE resulted equal to 72.66 USD/MWh. The sodium-salt HX design that minimizes the LCOE resulted in a single-shell/single tube pass configuration, with vertical alignment, characterized by an overall height of 15 m, and a shell diameter of 1.8 m. It represents the 3.2% of the total capital cost of the plant. An interesting system-level optimization was then carried out on the combined receiver-heat exchanger block. It regarded the variation of the Log Mean Temperature Difference (LMTD) of the HX and highlighted the possibility to drop the LCOE down to 68.54 USD/MWh. The techno-economic investigations and the sensitivity analysis showed the flexibility and robustness of the HX model, as well as the importance of the NaSaltsCO2System. The latter lays the groundwork to explore potential improvements of this new generation of CSP systems, which can play a fundamental role in the future global energy mix. / Termisk solkraft (CSP) är en av de mest lovande elproduktionsteknologierna baserade på förnybar energi. Den kan bidra till hanteringen av den ökande efterfrågan på energi och miljömässig hållbarhet. I syfte att uppnå 2020 SunShot-kostnadsmålet för CSP på 60 USD/MWh presenterade USA:s energidepartement Gen3 CSPinitiativet. I synnerhet föreslår CSP Gen Liquid-Phase Pathway att utforma ett CSPsystem som använder flytande natrium som värmeöverföringsvätska i mottagaren, smält kloridsalt med hög temperatur som lagringsvätska, samt superkritisk CO2 (sCO2) Brayton-cykel som kraftcykel. Syftet för detta examensarbete var att utforma natriumkloridsaltets primära värmeväxlare genom att utveckla både en värmeväxlarmodell (HX) modell och en natriumsalt-sCO2-systemmodell. För att fullfölja dessa syften utvecklades HX-modellen först, sedan implementerades natriumsalt-sCO2 CSP-systemet NaSaltsCO2System. Båda verktygen utvecklades med hjälp av Modelica som programmeringsspråk. De finns nu tillgängliga i det öppna SolarTherm-biblioteket. När det gäller HX utvecklades en allmän modell för skal- och rörvärmeväxlare med möjligheten att anpassas när det gäller antagna medium, begränsningar, gränsvillkor och korrelationer. Dessutom utförde modellen en optimering för att välja den interna geometri-konfigurationen som optimerar en användardefinierad objektiv-funktion. Genom att använda den implementerade HX-modellen i NaSaltsCO2System designades natriumsalt-värmeväxlaren, vilket gav en fullständig konfiguration-beskrivning och en uppskattning av prestanda och kostnader. Den utvecklade NaSaltsCO2System-modellen visade sig vara robust och kapabel till att utföra simuleringar på årsbasis. Detta gjorde det möjligt att uppskatta CSP-anläggningens energiprestanda samt LCOE. Det utvecklade natriumsalt-sCO2 CSP-systemet som känneteckna des av en mottagarkapacitet på 543 MWth, 12 timmars TES och ett 100 MWe power block, resulterade i en LCOE på 72.66 USD/MWh. Natrium-salt HX-konstruktionen som minimerade LCOE resulterade i en enskalig/enkel rörpassningskonfiguration, med vertikal inriktning, kännetecknad av en total höjd av 15 m och en skaldiameter på 1.8 m. Det motsvarade 3.2% av anläggningens totala kapitalkostnad. Den mest intressanta systemoptimeringen genomfördes på det kombinerade blocket bestående av mottagare och värmeväxlare. Den behandlade variationen av HX:s LMTD och framhöll möjligheten att sänka LCOE till 68.54 USD/MWh. De teknisk-ekonomiska undersökningarna och känslighetsanalysen visade flexibiliteten och robustheten i HX-modellen, liksom vikten av NaSaltsCO2Systemet. Den senare lägger grunden för att utforska potentiella förbättringar av denna nya generation av CSP-system, som kan spela en grundläggande roll i den framtida globala energimixen.

Les protéines de type prion, contenant des Séquences en acides aminés de Faible Complexité (SFC), ont tendance à s’agréger et à former des compartiments non-membranaires dans la cellule. Ces derniers ont des propriétés physiques communes à celles des liquides, telles que la capacité de mouiller les surfaces, de s’écouler et de fusionner avec d’autres corps liquides. Dans cette étude, nous avons démontré que la protéine Hrp1 forme, in vitro, des gouttes de différentes tailles via une transition de phase liquide à liquide, et ce, uniquement lorsqu’elle est exposée à un milieu chargé négativement. Exclusivement dans ce même milieu, nous avons aussi observé que le domaine SFC de Hrp1 s’assemble et forme une matière de type gel. Sur la base de ces observations, nous avons émis l’hypothèse que la tendance des systèmes moléculaires à former des compartiments liquides in vivo peut être influencée par la présence, dans le cytosol, de polyélectrolytes chargés négativement tels que l'ADN, l'ARN et les polyphosphates (PolyP). En utilisant la levure comme modèle cellulaire et des techniques de microscopie à fluorescence, nous nous sommes focalisés sur l’étude du rôle des PolyP dans l'assemblage des P-bodies. Les P-bodies ont été choisis comme système moléculaire de référence in vivo, étant des corps qui, après une transition de phase, se trouvent dans le cytosol sous forme de gouttes. Nous avons démontré que la déplétion du phosphate et la délétion du gène vtc4, responsable de la synthèse des PolyP dans la levure, n’ont pas d’influence dans la formation des P-bodies. Nous avons aussi remarqué que les PolyP et la protéine Edc3, une des composantes principales des P-bodies, ne sont pas co-localisés dans la cellule. Cette étude préliminaire nous suggère un manque de corrélation entre la formation des P-bodies et la présence de PolyP dans la cellule. Cependant, pour confirmer nos observations, des expériences complémentaires doivent être envisagées, en considérant d’autres composantes des P-bodies, tel que Lsm4, ou en analysant, in vivo, les effets des PolyP sur d’autres systèmes moléculaires de nature liquide. / Prion-like proteins containing Low Complexity Sequences (LCSs) have the propensity to aggregate and form membrane-less compartments in the cell. These proteins form droplets that have liquid features such as wetting, dripping and fusion. In this study, we demonstrated that the prion domain-containing protein Hrp1 forms droplets of different sizes in the presence of negatively charged polymers via liquid-liquid phase separation, whereas under the same conditions, the prion-like domain PolyQ/N of Hrp1 forms a gel-like material. Based on these findings, we hypothesize that droplets in vivo could be modulated by negatively charged polyelectrolytes found in the cell such as DNA, RNA and polyphosphate (PolyP). My goal was to examine the role of the polyanionic nature of PolyP on the assembly of P-bodies using Saccharomyces cerevisiae as a cellular model and fluorescence microscopy. We chose to study processing (P)- bodies, based on previous findings that these cellular subcompartments are formed by liquid-liquid phase separation of component proteins in the cytoplasm. We found that depleting phosphate from the media and deleting vtc4 gene, which is responsible for PolyP synthesis, did not have any effect on P-body formation. In addition, we demonstrated that PolyP and the protein Edc3, a core component of P-bodies, do not colocalize. Our data suggest that PolyP does not affect P-body formation. However, further and complementary studies have to be performed to confirm that PolyP have no effects on other membrane-less organelles.

No description available.

Un procédé sol-gel développé au laboratoire a été appliqué à des précurseurs hétéroleptiqueset/ou hétérométalliques pour l’élaboration de nouveaux matériaux hybrides et/ou dopés.Des nanoparticules de TiO2 dopées par le gadolinium et l’europium ont été obtenues sous formede nanocristallites d’anatase par ce procédé basse température. Leurs performancesmagnétiques et luminescentes ont été évaluées afin de pouvoir les utiliser comme agents decontraste pour l’imagerie médicale. L’utilisation d’un précurseur hétérométallique ethétéroleptique contenant à la fois du titane, du gadolinium et du PABA a pu conduire à laformation de matériaux dopés et hybrides en une seule étape. L’utilisation future de cesmatériaux dans le domaine biomédical est envisagée.La deuxième partie de ce travail a consisté en l’élaboration de supports hybrides TiO2(citrate) en appliquant le même procédé de co-hydrolyse à un nouvel alcoxyde de titane comportant le ligand citrate. Plusieurs degrés de fonctionnalisation organique de surface ont été obtenus par la modification des quantités relatives des précurseurs de départ. En mettant simplement en présence ces supports avec des solutions aqueuses de sels d’or ou d’argent, les fonctions citrates ont permis la formation de particules métalliques directement à la surface des supports. Ces matériaux M/TiO2 ont été utilisés en tant que catalyseurs dans l’époxydation du transstilbène en phase liquide et ont permis d’améliorer la connaissance des mécanismes de cette réaction aérobie. / A new and relevant sol-gel process has allowed us to prepare new hybrid materials. Titania nanoparticles with lanthanides doping agent (gadolinium and europium) were obtained as anatase nanocrystallites via our low-temperature process. Their magnetic and luminescent properties have been tested in order to use them as contrast agent in medical imaging. A doped and hybrid material has also been obtained and its NH2 groups at the surface will be used in thebio-medical field. The second part of this work has consisted in the preparation of TiO2(citrate) hybrid supports viaa new titanium alkoxide that contains a citrate ligand. Several surface citrate density had been obtained by changing the precursor’s initial relative amounts. Then the simple contact between these hybrid supports and aqueous solutions of silver or gold ions led to the formation of metallic particles directly on the surface support thanks to the presence of the citrate groups, which are known to be reducing agent. These M/TiO2 materials were then tested as catalysts in the aerobic epoxidation of trans-stilbene in the liquid phase. Through this study, we were able to improve our knowledge in this reactionmechanism.

A esterificação do sec-butanol com ácido acético, submetida à catálise homogênea, apresenta poucos resultados experimentais de cinética reacional e equilíbrio químico disponíveis na literatura. A presente dissertação visa determinar os parâmetros cinéticos e de equilíbrio químico desta reação de esterificação, empregando modelo cinético de 2ª ordem baseado em atividades. Os experimentos cinéticos foram realizados em reator batelada com auxílio da metodologia Karl Fischer para análise do teor de água e determinação do perfil de frações molares ao longo da reação. A principal dificuldade na modelagem desta esterificação consistiu em representar satisfatoriamente as não-idealidades da mistura em fase líquida, em espacial nas reações cuja fração molar inicial de ácido acético foi superior a 50%. Netas condições admitiu-se a ocorrência de dissociação do ácido acético levando ao surgimento de interações iônicas. O modelo empregado para obtenção das atividades, com base em frações molares, foi o NRTL. Este modelo representou bem as interações moleculares em condição de baixa acidez, mas apresentou desvios em condições de acidez e teores de água mais elevados. O estudo também visou o desenvolvimento de modelos de calibração para um método analítico on-line visando determinar o perfil de frações molares ao longo da reação. O método empregado foi a espectroscopia de infravermelho próximo (NIR), em vista à capacidade deste método analítico em determinar quantitativamente frações molares de água, além dos demais compostos envolvidos. Outro fator determinante ao emprego do NIR é a seu crescente uso no meio industrial, e o presente trabalho visou também contribuir para o uso futuro desta técnica de monitoramento no processo industrial. Modelos de calibração multivariável com conjuntos de calibração interna por validação cruzada se mostraram adequados ao sistema estudado. Calibrações externas resultaram em modelos imprecisos, não sendo possível determinar claramente os fatores responsáveis pela imprecisão. / There is a lack of literature data on the reaction kinetics and equilibrium of the homogeneously catalyzed esterification of sec-butanol with acetic acid. This work aims at obtaining the kinetic parameters and chemical equilibrium parameters of this esterification reaction by using a second order kinetic model based on activities. The kinetic experiments were performed in a batch reactor and the Karl Fischer analytical method was used to determine the molar fraction of water along the reaction progress. The main challenge of modeling this reaction was to represent the highly non-ideal mixture in liquid phase, specially for reactions runs starting with acetic acid mole fraction higher than 50%. In these conditions, it was assumed the occurrence of acetic acid dissociation that leads to ionic interactions. The thermodynamic model used to calculate the activities was the NRTL. This model predicted well the molecular interactions on low acidity conditions but presented deviations when molar fractions of acid and water were higher. The present study also aims to develop calibration models for analytical on-line method to obtain molar fraction profiles along the reaction. Near infrared spectroscopy (NIR) was used due to the possibility of quantitatively analyze water mole fraction, besides the mole fractions of the other components. Another important reason to choose NIR was its crescent use in industry, and the present work intended to contribute towards the future use of this on line monitoring technique in industrial applications. Multivariate calibration models using internal set of calibration and cross-validation seems to be suitable for this system. External set of calibration leads to less accurate models, and the causes of this lack of accuracy were not clearly identified.

O aleitamento materno está associado a benefícios de ordem nutricional, imunológica, afetiva, econômica e social. Grande parte das drogas lícitas e ilícitas consumidas pela lactante pode ser transferida para o leite, o que pode representar potenciais efeitos nocivos para a criança em curto e longo prazos. Embora o conhecimento a respeito de substâncias psicoativas durante a lactação venha sendo ampliado, ainda há poucas informações sobre as concentrações de substâncias excretadas por essa via e muitas dúvidas sobre os efeitos delas em crianças durante o período de amamentação. O leite materno é uma matriz não convencional que pode ser usada para avaliar a exposição de crianças a substâncias durante o aleitamento e sua principal vantagem é a coleta simples e não-invasiva. Contudo, a extração destas a partir do leite materno é um desafio analítico devido ao seu alto conteúdo lipídico e proteico, bem como a alteração na sua composição durante o período pós-parto. No presente trabalho, técnicas analíticas miniaturizadas foram desenvolvidas visando a detecção das substâncias psicoativas cocaína, cocaetileno, norcocaína, tetraidrocanabinol, canabinol, canabidiol em amostras de leite materno, utilizando cromatografia gasosa acoplada à espectrometria de massas (GC-MS). A microextração em fase líquida (LPME) foi aplicada para analitos de cocaína e a microextração em fase sólida (SPME) para canabinoides. Após o desenvolvimento e validação dos métodos, as análises foram aplicadas em amostras de leite coletadas no hospital municipal Dr. Arthur Ribeiro de Saboya (n=109). Além das técnicas terem se mostrado adequadas à extração e detecção dos analitos, confirmou-se a excreção de cocaína no leite materno em quantidades moderadas com resultado positivo para uma amostra (138 ng/mL). Bem como foi detectado tetraidrocanabinol nas concentrações de 20 ng/mL e 31 ng/mL em amostras de leite humano. / Maternal breastfeeding is related with nutritional, immunological, affective, economic, and social benefits. Most licit and illicit substances consumed by the nursing mother might be excreted in breast milk, which may cause potential harmful effects to the breastfed infant at short and long terms. Although the knowledge about the psychoactive substances during lactation is increasing, there is still few information on the levels in which these substances are excreted in breast milk and many questions about the possible effects of these substances in the infant during the nursing period still remain unanswered. Breast milk is an unconventional matrix that can be used to assess infant exposure to drugs, and its main advantage is its easy and non-invasive collection. However, the extraction of substances from breast milk is an analytical challenge because of its high protein and fat content and changing composition during the postpartum period. In this study, miniaturized analytical techniques will be carried out to determine psychoactive substances such as cocaine, cocaethylene, norcocaine, tetrahydrocannabinol, cannabinol, and cannabidiol in milk samples by using gas chromatography-mass spectrometry (GC-MS). Liquid-phase microextraction (LPME) was applied to cocaine analytes and solid-phase microextraction (SPME) was applied to cannabinoids. After the development and validation, the methods were applied in milk samples collected from municipal hospital Dr. Arthur Ribeiro de Saboya (n=109). These techniques have proved to be suitable for analyte extraction and detection. Cocaine excretion in breast milk has been confirmed given that one sample was positive to cocaine in moderate amounts (138 ng/mL), as well as, two samples could be confirmed positive to tetrahydrocannabinol at 20 ng/mL and 31 ng/mL.

Os antidepressivos pertencem a uma importante classe de medicamentos investigados na toxicologia forense. Em casos de amostras provenientes de cadáveres, o intervalo entre o óbito e a obtenção da espécie biológica pode proporcionar a redistribuição postmortem destes fármacos. Com o objetivo de elucidar esse fenômeno, métodos analíticos foram desenvolvidos e aplicados utilizando sangue total (ST), humor vítreo (HV) e fígado. Para as amostras de ST e HV, o método de extração escolhido e validado foi a microextração em fase líquida (LPME) trifásica. Fibras ocas constituídas de polipropileno, com a extensão de 8 cm cada, foram tratadas com o solvente orgânico dodecano (fase orgânica), resultando em um membrana com permeabilidade seletiva. No lúmen destas fibras, adicionou-se ácido fórmico 0,1 mol/L (fase aceptora). Em frasco de fundo chato com 5 mL de capacidade, pipetou-se 3,5 mL de NaOH 0,1 mol/L (fase doadora) e 0,5 mL de ST ou HV. Ao término da extração, as amostras foram introduzidas no GC-MS, sem a necessidade de reações de derivatização. O estudo com ST contemplou os antidepressivos amitriptilina (AMI), nortriptilina (NTR), imipramina (IMI), desipramine (DES), clomipramina (CLO), desmetilclomipramina (DMC), fluoxetina (FLU) e norfluoxetina (NFL). Os limites de quantificação para estas substâncias ficaram inferiores aos níveis terapêuticos (20 ng/mL). As médias dos coeficientes de variação intradia e interdia foram, respectivamente, de 9,7 e 9,8%. As curvas de calibração apresentaram linearidade entre as concentrações de 20 até 1200 ng/mL. A validação do parâmetro integridade da diluição assegurou a mensuração de quantidades superiores ao limite apresentado na curva de calibração. O método foi aplicado em sete amostras reais postmortem e em apenas um caso foi observada uma diferença significativa (300%) entre os valores quantificados no ST periférico e central. Os antidepressivos tricíclicos AMI, NTR, IMI e DES foram avaliados no HV e o efeito matriz foi detectado para os dois últimos analitos. O método foi otimizado e validado utilizando solução salina adicionada de AMI e NTR. O limite de detecção igual a 5 ng/mL, foi obtido com a redução da voltagem da fonte de íons do espectrômetro de massa para 50 eV. Coeficientes de variação foram inferiores a 15%. Os procedimentos validados foram aplicados em seis amostras reais de HV. A relação encontrada entre os valores obtidos no ST periférico e HV foi de aproximadamente 0,1. A extração acelerada por solvente (ASE) e, posteriormente, a extração em fase sólida (SPE) foram as técnicas de separação dos analitos da matriz fígado. Ao término das citadas extrações, os antidepressivos foram analisados no GC-MS. Para esta matriz sólida, são necessários mais estudos, pois os valores encontrados nos ensaios analíticos estão em desacordo com as diretrizes utilizadas na validação dos métodos. / Antidepressants belong to an important class of drugs investigated in forensic toxicology. In cases of samples from corpses, the interval between death and obtaining the biological specimens can provide the postmortem redistribution of these drugs. Aiming to elucidate this phenomenon, analytical methods were developed and applied using whole blood (WB), vitreous humor (VH) and liver. For samples of WB and HV, the extraction method chosen and validated was the three-phase liquid phase microextraction (LPME). Hollow fibers consist of polypropylene, with a length of 8 cm each were treated with dodecane organic solvent (organic phase) resulting in a membrane with selective permeability. Into the lumen of these fibers was added formic acid 0.1 mol/ L (acceptor phase). In the vial containing 3.5 mL of NaOH 0.1 mol / L (donor phase) was spiked 0.5 ml of biological fluids (WB or VH). Subsequently, the samples were injected in GC-MS without derivatization reactions. The study of the ST included antidepressants amitriptyline (AMI), nortriptyline (NTR), imipramine (IMI), desipramine (DES), clomipramine (CLO), desmethylclomipramine (DMC), fluoxetine (FLU) and norfluoxetine (NFL). The quantification limits for these substances were below the therapeutic levels (20 ng / ml). The mean coefficients of variation and separate intradays were respectively 9.7 and 9.8%. The calibration curves showed linearity between concentrations of 20 to 1200 ng / mL. The validation of the integrity of the dilution parameter assured measurement higher than the limit shown in the calibration curve quantities. The method was applied to seven real postmortem samples and in one case a significant difference (300%) between the measured values in the peripheral and central ST was observed. The tricyclic antidepressants AMI, NTR, IMI and DES were evaluated in VH and the matrix effect was detected in the last two analytes. The method was optimized and validated using saline spiked AMI and NTR. The limit of detection (5 ng/ml) was obtained by reducing the voltage of the ion source of the mass spectrometer 50 eV. Coefficients of variation were below 15%. The procedures were validated in six real samples of HV. The relationship found between the values obtained in the peripheral ST and HV was approximately 0.1. Accelerated solvent extraction (ASE) and subsequently the solid phase extraction (SPE) were the techniques of separation of analytes liver matrix. At the end of the cited extractions, antidepressants were analyzed in GC-MS. To this solid tissue, further studies are needed, because the values found in the analytical tests were not in accordance with the guidelines used in the validation of the methods.

L'objectif d'un avion plus électrique conduit à l'utilisation croissante de systèmes d'électronique y compris dans des zones de haute température. Les modules de puissance classiques doivent être adaptés à cet environnement: les composants en SiC sont commercialement disponibles mais l'environnement de la puce est à modifier. Cette thèse s'intéresse aux techniques d'attaches de puces basses température que sont le frittage d'argent et la brasure en phase liquide transitoire (TLPB) or-étain. Dans une première partie, les enjeux de l'électronique de puissance et plus particulièrement des applications haute température est donnée. Les mécanismes physique (mouillage, diffusion)qui régissent le frittage et le TLPB (Transient liquid Phase Bonding) sont ensuite décrits avec précision. La deuxième partie de cette thèse s'intéresse à la mise en oeuvre d'un protocole fiable d'attache de puce par frittage d'une nanopoudre d'argent commerciale. Une fois établie, la méthode a ensuite été optimisée pour différentes tailles de composants. La caractérisation de l'attache a été réalisée en shear-test et par des images en microscopie optique. La troisième et dernière partie de ce travail a pour objet la réalisation d'attaches de puces par TLPB or-étain. Ce chapitre traite de la mise en oeuvre expérimentale de la technique, depuis la métallisation des wafers jusqu'à la caractérisation des attaches en microscopie (optique et MEB). Ce travail de thèse est très expérimental car même si un protocole de mise en oeuvre existe (pour le frittage), il est indispensable de l'adapter aux conditions expérimentales pour l'optimiser. Ce travail a aussi mis en évidence certaines difficultés techniques de préparation des surfaces. / More electric aircaft projects lead to the increasing use of power electronic systems including in high temperature areas. Classical power modules must be adapted to this harsh environment: SiC devices are now commercially available but the packaging of the dies must be completely changed. This thesis focus on alternative die-backside attaches aand particularly on sintering and Transient Liquid Phase Bonding (TLPB) which are classified as Low Temperature Joining Techniques. In the first part, importance of power electronic systems for high temperature applications is given. Theoretical considerations about physical mechanisms (diffusion, wetting) involved in sintering and TLPB are described precisely. The purpose of the second part of this thesis is to establish a realiable protocole of die-attach using commercial silver nanopaste.the method has been optimized for different sizes of devices. Caracterization was provided using optical pictures and shear-test results. The third chapter of this work is about the realization of die-attaches using TLPB method. A description of surfaces preparation is given and diffusion results are discussed using SEM and optical pictures. This work is very experimental because sintering classical procedure must be adapted and optimized for each kind of devices. This thesis has clealy shown the difficulties for surfaces preparation.

O aleitamento materno está associado a benefícios de ordem nutricional, imunológica, afetiva, econômica e social. Grande parte das drogas lícitas e ilícitas consumidas pela lactante pode ser transferida para o leite, o que pode representar potenciais efeitos nocivos para a criança em curto e longo prazos. Embora o conhecimento a respeito de substâncias psicoativas durante a lactação venha sendo ampliado, ainda há poucas informações sobre as concentrações de substâncias excretadas por essa via e muitas dúvidas sobre os efeitos delas em crianças durante o período de amamentação. O leite materno é uma matriz não convencional que pode ser usada para avaliar a exposição de crianças a substâncias durante o aleitamento e sua principal vantagem é a coleta simples e não-invasiva. Contudo, a extração destas a partir do leite materno é um desafio analítico devido ao seu alto conteúdo lipídico e proteico, bem como a alteração na sua composição durante o período pós-parto. No presente trabalho, técnicas analíticas miniaturizadas foram desenvolvidas visando a detecção das substâncias psicoativas cocaína, cocaetileno, norcocaína, tetraidrocanabinol, canabinol, canabidiol em amostras de leite materno, utilizando cromatografia gasosa acoplada à espectrometria de massas (GC-MS). A microextração em fase líquida (LPME) foi aplicada para analitos de cocaína e a microextração em fase sólida (SPME) para canabinoides. Após o desenvolvimento e validação dos métodos, as análises foram aplicadas em amostras de leite coletadas no hospital municipal Dr. Arthur Ribeiro de Saboya (n=109). Além das técnicas terem se mostrado adequadas à extração e detecção dos analitos, confirmou-se a excreção de cocaína no leite materno em quantidades moderadas com resultado positivo para uma amostra (138 ng/mL). Bem como foi detectado tetraidrocanabinol nas concentrações de 20 ng/mL e 31 ng/mL em amostras de leite humano. / Maternal breastfeeding is related with nutritional, immunological, affective, economic, and social benefits. Most licit and illicit substances consumed by the nursing mother might be excreted in breast milk, which may cause potential harmful effects to the breastfed infant at short and long terms. Although the knowledge about the psychoactive substances during lactation is increasing, there is still few information on the levels in which these substances are excreted in breast milk and many questions about the possible effects of these substances in the infant during the nursing period still remain unanswered. Breast milk is an unconventional matrix that can be used to assess infant exposure to drugs, and its main advantage is its easy and non-invasive collection. However, the extraction of substances from breast milk is an analytical challenge because of its high protein and fat content and changing composition during the postpartum period. In this study, miniaturized analytical techniques will be carried out to determine psychoactive substances such as cocaine, cocaethylene, norcocaine, tetrahydrocannabinol, cannabinol, and cannabidiol in milk samples by using gas chromatography-mass spectrometry (GC-MS). Liquid-phase microextraction (LPME) was applied to cocaine analytes and solid-phase microextraction (SPME) was applied to cannabinoids. After the development and validation, the methods were applied in milk samples collected from municipal hospital Dr. Arthur Ribeiro de Saboya (n=109). These techniques have proved to be suitable for analyte extraction and detection. Cocaine excretion in breast milk has been confirmed given that one sample was positive to cocaine in moderate amounts (138 ng/mL), as well as, two samples could be confirmed positive to tetrahydrocannabinol at 20 ng/mL and 31 ng/mL.

Compte tenu du récent taux alarmant d'épuisement des réserves de combustibles fossiles et de l'augmentation drastique des niveaux de CO2 dans l'atmosphère qui a conduit au réchauffement de la planète et à des changements climatiques sévères, l'exploitation de toutes sortes d'énergies renouvelables a été la Parmi les principales priorités de la recherche Champs à travers le monde. L'une des nombreuses voies de ce genre est la réduction du CO2 aux combustibles utilisant des énergies renouvelables, plus communément appelées cellules photoélectro-catalytiques (PEC). Des essais expérimentaux sur la réduction du CO2 ont été réalisés sur différents types de catalyseurs dans les deux cellules (Conçu par un laboratoire) afin de comprendre la sélectivité, la productivité et les produits de réaction obtenus. Des essais expérimentaux ont été réalisés sur différents types de catalyseurs à la fois dans les cellules en phase gazeuse et en phase liquide pour comprendre la sélectivité, la productivité et les produits de réaction obtenus. Pour les études sur la réduction EC du CO2 en phase gazeuse, une série d'électrodes (à base de nanoparticules (NPs) de Cu, Fe, Pt et CuFe déposées sur des nanotubes de carbone ou de noir de carbone puis placées à l'interface entre une membrane Nafion et Une électrode à couche de diffusion de gaz). Les résultats démontrent le type divers de produits formés et leurs productivités. Dans des conditions sans électrolyte, la formation de produits ≥C1 tels que l'éthanol, l'acétone et l'isopropanol a été observée la plus élevée étant pour Fe et suivie de près par Pt. Pour améliorer Combustibles nets, un ensemble différent d'électrodes a été préparé sur la base de revêtements MOF de type imidazolate de type zéolitique substitué (SIM-1) (Fe-CNT, Pt-CNT et CuFe-CNT basés sur MOF) Et Pt-MOF a montré des carburants améliorés. En se reportant aux études sur la réduction EC du CO2 dans une cellule en phase liquide, un ensemble similaire d'électrodes a été prepare (NP - Cu, Fe, Pt, Ru, Co déposées sur des nanotubes de carbone ou du noir de carbone ont). Pour les conditions de phase liquide, en termes de produits C nets, les électrodes catalytiques à base de Pt sont en tête de la catégorie, suivies de près par Ru et Cu, tandis que Fe a obtenu la position la plus basse. Le mécanisme réactionnel sous-jacent probable a également été fourni. Afin d'améliorer encore les performances, on a synthétisé des NP de metal (Ru, Fe, Pt et Cu) de différentes tailles en utilisant différentes techniques de synthèse: (i) l'itinéraire d'imprégnation (ImR) pour obtenir des NP dans la plage de tailles de 10 à 50 nm; (Ii) Approche organométallique (OM) pour synthétiser des NPs uniformes et ultrafines dans la plage de tailles de 1-5 nm. Fe ont été synthétisés par une nouvelle voie de synthèse et des conditions pour atteindre des NP de 1 à 3 nm. (Iii) Approche de haut en bas de Nanowire pour obtenir des NP de cuivre ultrafin dans la plage de taille de 2-3,8 nm. Les améliorations apportées à la productivité du carburant se sont révélées être de 5 à 30 fois plus élevées pour les petites NP sur les NP plus importantes et, en outre, une charge réduite de 10 à 1-2% en poids. Un autre ensemble d'électrodes à base de nano-mousses (Cu NF et Fe NF sur Feuille de Cu, Feuille de Foie, Al Foil, Inconel foil et Al grid / mesh) préparés par électrodéposition ont également été étudiés afin d'améliorer encore la conversion de CO2 / carburant. Après, l'optimisation du dépôt et de la tension à l'aide de la voltamétrie cyclique, les carburants se sont améliorés de 2 à 10 fois par rapport aux combustibles nets les plus élevés obtenus à l'aide d'électrodes CNT dopées à base de NP / In view of the recent alarming rate of depletion of fossil fuel reserves and the drastic rise in the CO2 levels in the atmosphere leading to global warming and severe climate changes, tapping into all kinds of renewable energy sources has been among the top priorities in the research fields across the globe. One of the many such pathways is CO2 reduction to fuels using renewable energies, more commonly referred as photo-electro-catalytic (PEC) cells. Experimental tests were carried out on various types of catalysts in both the gas and liquid phase cells (lab-designed) to understand the different selectivity, productivity and the reaction products obtained. For the studies on the EC reduction of CO2 in gas phase cell, a series of electrodes (based on Cu, Fe, Pt and Cu/Fe metal nanoparticles – NPs - deposited on carbon nanotubes – CNTs - or carbon black and then placed at the interface between a Nafion membrane and a gas-diffusion-layer) were prepared. Under gas phase, the formation of ≥C1 products (such as ethanol, acetone and isopropanol) were observed, the highest being for Fe and closely followed by Pt, evidencing that also non-noble metals can be used as efficient catalysts under these conditions. To enhance the net fuels, a different set of electrodes were also prepared based on substituted Zeolitic Imidazolate (SIM-1) type MOF coatings (MOF-based Fe-CNTs, Pt-CNTs and Cu/Fe-CNTs) and Pt-MOF showed improved fuels. Moving to the studies on the EC reduction of CO2 in liquid phase cell, a similar set of electrodes were prepared (metal NPs of Cu, Fe, Pt, Ru and Co deposited on CNTs or carbon black). For liquid phase conditions, in terms of net C-products, catalytic electrodes based on Pt topped the class, closely followed by Ru and Cu, while Fe got the lowest position. The probable underlying reaction mechanism was also provided. In order to improve further the performances, varied sized metal NPs (Ru, Fe, Pt and Cu) have been synthesized using different techniques: (i) impregnation (ImR) route to achieve NPs in the size range of 10-50 nm; (ii) organometallic (OM) approach to synthesize uniform and ultrafine NPs in the size range of 1-5 nm (i.e., Fe NPs were synthesized through a novel synthesis route to attain 1-3 nm NPs); (iii) Nanowire (NW) top-down approach to obtain ultrafine copper metal NPs in the size range of 2-3.8 nm. The enhancements in the fuel productivity were found to be 5-30 times higher for the smaller metal NPs over the larger metal NPs and moreover, with reduced metal loading from 10 to 1-2 wt %. A different set of electrodes based on nano-foams (Cu NF and Fe NF on Cu foil, Fe foil, Al foil, Inconel foil and Al grid/mesh) prepared via electro-deposition were also investigated, to further improve CO2 to fuels conversion. After, optimization of deposition and voltage using cyclic voltammetry, the fuels improved by 2-10 times over the highest net fuels achieved using metal NPs doped CNT electrodes