Polarisation of X-ray light is being investigated with polarimeters to extend the borders of what can be observed. Distant compact objects, such as pulsars, that are to small on the sky to be analysed with imaging can be investigated by analysing the polarisation of the emitted light. This can reveal physics previously hidden by their small nature. There are many models that aim to describe the polarisation of these compact objects to make sense of what is measured. Two examples are the outer gap and two-pole caustic models. The X-ray polarimeter XL-Calibur is a balloon-borne telescope capable of detecting X-rays in the $15-80$ keV energy range. In this thesis details on the polarisation of light, how it can be measured and some principles of X-ray polarimetery is discussed. A new feature in the simulation of XL-Calibur in Geant4 is also described and used to investigate the possibility for XL-Calibur to distinguish between different Crab pulsar polarisation models at different signal rates. The results show that signal rates under 2 Hz yield insufficient data to distinguish between the two models using the measured polarisation fraction and angle. For greater signal rates XL-Calibur does in fact differentiate between the models correctly. New methods for the statistical analysis of data can be explored to allow more data to be salvaged, even for low signal rates. The derivation of polarisation parameters is fixed through Stokes parameters in this thesis. / Polarisationen av röntgenljus undersöks med polarimetrar för att utvidga gränserna för vad som kan observeras. Avlägsna kompakta objekt, såsom pulsarer, som är för små och för långt borta på himlen för att analyseras med optiska metoder, kan undersökas genom att analysera polarisationen av det utstrålade ljuset. Detta kan avslöja fysik som tidigare var dold på grund av deras storlek. Det finns många modeller som syftar till att beskriva polarisationen av dessa kompakta objekt för att förstå vad som mäts. Två exempel är modellerna: outer gap och two-pole caustic. Röntgenpolarimetern XL-Calibur är ett ballongburet teleskop som kan detektera röntgenstrålning i energiområdet $15-80$ keV. I denna avhandling diskuteras detaljer om ljusets polarisation, hur det kan mätas och några principer för röntgenpolarimetri. En ny funktion i simuleringen av XL-Calibur i Geant4 beskrivs också. Den används för att undersöka möjligheten för XL-Calibur att särskilja mellan olika polariseringsmodeller för Krabbpulsaren vid olika signaltakter. Resultaten visar att för signaltakter under 2 Hz, blir datan otillräcklig för att särskilja mellan de två modellerna både för polarisationsgraden och vinkeln. För högre signaltakter kan XL-Calibur skilja mellan modellerna. Nya metoder för statistisk analys av data kan utforskas för att möjliggöra att mer data kan användas, även för låga signaltakter. I denna avhandling beräknas polarisationsparametrarna genom Stokesparametrarna.

X-ray polarimetry, the study of the polarisation of X-ray light, is a powerful and rapidly developing tool for astrophysics, which promises to help answer outstanding questions about the physics of extreme objects such as pulsars, X-ray binaries and active galactic nuclei. The balloon-borne telescope XL-Calibur will be the first instrument to study the polarisation of hard X-rays (with energies between 10 and 100 keV) in detail, correlating with the soft X-ray observations of IXPE to provide further tests of polarisation-dependent x-ray emission models in extreme objects. The working principles of XL-Calibur are described, together with the necessary steps to measure the polarisation of X-rays. In these steps, Geant4 simulations of the telescope play a vital role, and the simulations are thus described in detail, together with the experiments done to validate the simulations. These experiments were performed at Esrange, Sweden during the XL-Calibur flight campaign in May of 2022, and the experimental setup and design of the validation experiments are described, as well as the specific simulations performed to replicate the experiment. The simulations show very good agreement with validation experiments, achieving a simulated modulation factor (a measure of the polarimetric response intrinsic to the detector) of 41.88% ± 0.17%, within one standard deviation of the measured 41.95% ± 0.18%. The optical effects of the XL-Calibur X-ray mirror is also simulated to good agreement with experimental results, necessary for simulating flight observations. Thus, the simulations can be used to simulate XL-Calibur for polarisation measurements and analysis. Furthermore, the effect on polarisation parameters of the mirror focal spot being offset is investigated. It is shown that it affects the modulation factor and thus the measured polarisation parameters, increasing the importance of using simulations to replicate and compensate for these effects during a data-taking flight with XL-Calibur. / Röntgenpolarimetri, att undersöka polariseringen hos röntgenljus, är ett kraftfullt redskap inom astrofysiken som är under snabb utveckling. Förhoppningen är att tekniken ska hjälpa till att lösa obesvarade frågor inom fysiken som beskriver extrema objekt såsom pulsarer, röntgenbinärer och aktiva galaxkärnor. Det ballongburna teleskopet XL-Calibur kommer att vara det första instrumentet som studerar polariseringen av hårda röntgenstrålar (med energi mellan 10 och 100 keV) i detalj, och genom att korrelera med IXPEs observationer i mjuka röntgenstrålar kommer polarisationsberoende modeller för bildandet av röntgenstrålar runt extrema objekt att testas. En beskrivning av hur XL-Calibur fungerar ges, tillsammans med de nödvändiga stegen för att mäta polariseringen hos röntgenljus. I dessa steg är simulering av teleskopet i Geant4 en vital del, och simuleringen beskrivs därav ingående tillsammans med experimenten som gjordes för att validera simuleringen. Dessa experiment utfördes på Esrange, Sverige i maj 2022, före XL-Caliburs första flygning. Experimentuppställningen och utformningen av dessa valideringsexperiment beskrivs tillsammans med de specifika simuleringar som gjordes med mål att replikera experimenten. Simuleringarna visar mycket god överensstämmelse med experimenten, med en modulationsfaktor (ett instrumentspecifikt mått av polarisationsgraden) på 41.88% ± 0.17%, inom en standardavvikelse från experimentens 41.95% ± 0.18%. Även de optiska effekterna från XL-Caliburs röntgenspegel simuleras och visar god överensstämmelse med mätningar, vilket är nödvändigt för att kunna simulera data tagen under en flygning. Därmed kan simuleringarna användas för att göra polarisationsmätningar och -analys. Slutligen görs en undersökning av effekten på polarisationsparametrarna av förskjutning av röntgenspegelns fokus. Denna visar att modulationsfaktorn och därmed polarisationsparametrarna ändras på ett betydande vis, vilket ökar vikten av att använda simuleringar för att reproducera och kompensera för dessa effekter under en datainsamlingsflygning med XL-Calibur.

This thesis treats static and dynamic surface characterization using radiometric and Fourier optical methods. A Fourier optical method has been developed for real time image processing in paper production and printing applications. It has been shown that the method can be used to measure crepe frequency, an important parameter in tissue paper production, as well as to monitor the wire mark pattern at paper web velocities of up to 20 m/s. The wire mark pattern has been used to measure dimensional variations across a paper web. These are important for the mechanical properties of paper. Imaging of the moving surfaces onto a spatial light modulator, necessary for Fourier optical analysis of opaque objects, constitutes a motion blur problem. This problem has been solved by means of optical motion compensation using a rotating mirror. A rotating mirror system has also been developed for the inspection of small particles fixed to a rotating sample disc. The optical motion compensation configurations have made exposure times of more than two orders of magnitude longer than the exposure time without compensation possible. A light scattering model for opaque objects, for example coated paper, has also been developed and verified, with a coefficient of determination between theory and measurement ranging from r2=0.84 to r2=0.98, on various paper samples. The light scattering model has been used in the development of an instrument based on the photometric stereo principle. In this instrument the reflectance (or color) and topography of opaque samples are determined from two or more images of the sample illuminated from different directions. The method has been successfully used for studies of the relation between topography and print results in gravure and flexographic printing. Comparisons of surface height profiles measured with the photometric stereo method and profiles obtained with mechanical and optical scanning stylus instruments have shown coefficients of determination of up to r2=0.97. The main advantages of the method are the high speed, the scalability and the ability to obtain reflectance and surface height maps of a surface simultaneously.

Early detection is vital to successfully treating breast cancer, and mammography screening is the most efficient and wide-spread method to reach this goal. Imaging low-contrast targets, while minimizing the radiation exposure to a large population is, however, a major challenge. Optimizing the image quality per unit radiation dose is therefore essential. In this thesis, two optimization schemes with respect to x-ray photon energy have been investigated: filtering the incident spectrum with refractive x-ray optics (spectral shaping), and utilizing the transmitted spectrum with energy-resolved photon-counting detectors (spectral imaging). Two types of x-ray lenses were experimentally characterized, and modeled using ray tracing, field propagation, and geometrical optics. Spectral shaping reduced dose approximately 20% compared to an absorption-filtered reference system with the same signal-to-noise ratio, scan time, and spatial resolution. In addition, a focusing pre-object collimator based on the same type of optics reduced divergence of the radiation and improved photon economy by about 50%. A photon-counting silicon detector was investigated in terms of energy resolution and its feasibility for spectral imaging. Contrast-enhanced tumor imaging with a system based on the detector was characterized and optimized with a model that took anatomical noise into account. Improvement in an ideal-observer detectability index by a factor of 2 to 8 over that obtained by conventional absorption imaging was found for different levels of anatomical noise and breast density. Increased conspicuity was confirmed by experiment. Further, the model was extended to include imaging of unenhanced lesions. Detectability of microcalcifications increased no more than a few percent, whereas the ability to detect large tumors might improve on the order of 50% despite the low attenuation difference between glandular and cancerous tissue. It is clear that inclusion of anatomical noise and imaging task in spectral optimization may yield completely different results than an analysis based solely on quantum noise. / QC 20100714

<p>A new model for simulating non-Brownian flexible fibres suspended in a Newtonian fluid has been developed. Special attention has been given to include realistic flow conditions found in the industrial papermaking process in the key features of the model; it is the intention of the author to employ the model in simulations of the forming section of the paper machine in future studies.</p><p>The model considers inert fibres of various shapes and finite stiffness, interacting with each other through normal, frictional and lubrication forces, and with the surrounding fluid medium through hydrodynamic forces. Fibre-fluid interactions in the non-creeping flow regime are taken into account, and the two-way coupling between the solids and the fluid phase is included by enforcing momentum conservation between phases. The incompressible three-dimensional Navier-Stokes equations are employed to model the motion of the fluid medium.</p><p>The validity of the model has been tested by comparing simulation results with experimental data from the literature. It was demonstrated that the model predicts the motion of isolated fibres in shear flow over a wide range of fibre flexibilities. It was also shown that the model predicts details of the orientation distribution of multiple straight, rigid fibres in a sheared suspension. Model predictions of the viscosity and first normal stress difference were in good agreement with experimental data found in the literature. Since the model is based solely on first-principles physics, quantitative predictions could be made without any parameter fitting.</p> / <p>En ny modell för simulering av rörelserna hos icke-Brownska böjliga fibrer dispergerade i en Newtonsk vätska har utvecklats. Eftersom det är författarens avsikt att modellen skall kunna tillämpas vid simulering av arkformning under de förhållanden som råder i en modern pappersmaskin, har särskilt omsorg givits till att inkludera motsvarande flödesvillkor i modellens giltighetsområde.</p><p>Modellen hanterar fibrer av varierande form, massa och styvhet, som växelverkar sinsemellan via normal-, friktions- och smörjkrafter. Deras växelverkan med den omgivande vätskan sker via hydrodynamiska krafter vid finita Reynolds-tal. Den så kallade tvåvägskopplingen mellan fibrerna och vätskefasen har tagits i beaktande genom att kräva att rörelsemängden bevaras vid interaktionen mellan faserna. Vidare har Navier-Stokes ekvationer för inkompressibla vätskor använts för att beskriva mediets rörelser.</p><p>Modellens giltighet har undersökts genom att jämföra resultat från simuleringar med experimentella data från litteraturen. Det har påvisats att modellen förutsäger rörelsen hos ensamma fibrer i ett skjuvflöde, för vitt skilda fiberflexibiliteter. Det visades också att modellen förutsäger detaljer hos fiberorienteringsdistributionen i suspensioner utsatta för skjuvflöde. Det kunde också konstateras att modellens förutsägelser av fibersuspensioners viskositet och första normalspänningsdifferens under skjuvning väl överensstämde med experimentella data i litteraturen. Kvantitativa förutsägelser har kunnat göras utan någon parameteranpassning, då modellen bygger uteslutande på väletablerade fysikaliska samband inom klassisk mekanik och strömningslära.</p>

<p>Many different approaches have been taken towards solving the stereo correspondence problem and great progress has been made within the field during the last decade. This is mainly thanks to newly evolved global optimization techniques and better ways to compute pixel dissimilarity between views. The most successful algorithms are based on approaches that explicitly model smoothness assumptions made about the physical world, with image segmentation and plane fitting being two frequently used techniques.</p><p>Within the project, a survey of state of the art stereo algorithms was conducted and the theory behind them is explained. Techniques found interesting were implemented for experimental trials and an algorithm aiming to achieve state of the art performance was implemented and evaluated. For several cases, state of the art performance was reached.</p><p>To keep down the computational complexity, an algorithm relying on local winner-take-all optimization, image segmentation and plane fitting was compared against minimizing a global energy function formulated on pixel level. Experiments show that the local approach in several cases can match the global approach, but that problems sometimes arise – especially when large areas that lack texture are present. Such problematic areas are better handled by the explicit modeling of smoothness in global energy minimization.</p><p>Lastly, disparity estimation for image sequences was explored and some ideas on how to use temporal information were implemented and tried. The ideas mainly relied on motion detection to determine parts that are static in a sequence of frames. Stereo correspondence for sequences is a rather new research field, and there is still a lot of work to be made.</p>

Hydropower maintains its position as the most important source of renewable electric energy in the world. The efficiency of large hydropower plants is unsurpassed, and after more than hundred years of development, the technology is mature and highly reliable. While new hydro resources are currently being developed in Asia and South America, most European countries go through a phase of intense refurbishment and upgrading of existing plants. Challenges faced by the hydropower industry include a knowledge transfer to new generations and the adaptation of unit designs to meet new operational requirements. As with all branches of engineering, the use of computerized design tools has revolutionized the art of hydropower plant design and the analysis of its performance. In the present work, modern tools like coupled field-circuit models and semi-analytic permeance models are used to address different aspects of electromagnetic analysis of generators in large hydropower plants. The results include the presentation of a mathematical model that uses concepts from rotating field theory to determine the air-gap flux density waveform in a hydroelectric generator. The model was succesfully used to evaluate armature voltage harmonics and damper bar currents at no-load and load conditions. A second study is concerned with the importance of losses due to rotational fields in core loss calculations. It is found that dynamic and rotational effects typically increase the total core loss estimates with about 28% in large hydroelectric generators. In a third study, linear models for the calculation of salient pole shoe form factors at an arbitrary level of magnetic loading are presented. The effect of the damper winding configuration on the damping capability of salient-pole generators is then evaluated in a separate study. The predicted impact of the coupling between damper cages on adjacent poles on the damping torque production is verified in a set of experiments.

Magnetic thin films and patterned nanostructures have been studied with respect to their magnetic properties using SQUID-magnetometry, magnetic force microscopy, electrical measurements, and micromagnetic calculations. Properties of vortex domain walls, trapped in Permalloy nanowires with artificial constrictions, were investigated experimentally and by numerical calculations. In particular, the geometrical extent and strength of the pinning potential were evaluated. In these wires, long-range vortex domain wall displacement induced by spin polarized alternating currents was obtained numerically at reduced threshold current densities as compared with the direct current case. Due to the asymmetry of the energy potential, the long-range displacement direction is determined by the vortex chirality. Strained FeCo/Pt superlattices with strong perpendicular anisotropy were investigated experimentally. The strain was controlled by varying the thickness of each alternating layer with monolayer precision and was found to have a dominating effect on the total anisotropy. Epitaxial films of the diluted magnetic semiconductor (Ga,Mn)As were studied with focus on how the ferromagnetic transition temperature could be controlled by post-growth annealing. The ferromagnetic transition temperature was enhanced by approximately 85% for a Mn-doping concentration of 6% under certain conditions. A method to manipulate micrometer sized magnetic particles on patterned arrays of elliptical Permalloy microstructures was studied. Controlled motion and separation of the magnetic particles were obtained using applied rotating magnetic fields. The domain structure of the elliptical elements was studied numerically.

This thesis summarises work towards a Lab-on-Chip (LOC). The request for faster and more efficient chemical and biological analysis is the motivation behind the development of the LOC-concept. Microfluidic devices tend to become increasingly complex in order to include, e.g. sample delivery, manipulation, and detection, in one chip. The urge for smart and simple design of robust and low-cost microdevices is addressed and discussed. Design, fabrication and characterization of such microdevices have been demonstrated using low-cost polymer and glass microfabrication methods. The manufacturing is feasible, to a large extent, to perform outside the clean-room, and has subsequently been the chosen technique for most of the work. Issues of bonding reliability are solved by using polymer adhesive tapes. A planar electrocapture device with LOC-compatibility is demonstrated where beads are immobilised and released in a flowing stream. Retention of nanoparticles by means of electric field-flow fractionation using transparent indium tin oxide electrodes is presented. Moreover, a cast PDMS 4-way crossing is enabling a combination of liquid chromatography and capillary electrophoresis to enhance separation efficiency. Sample transport issues and a new flow-cell design in a quartz crystal microbalance bioanalyzer are also investigated. Fast bacteria counting by impedance measurements, much requested by the pharmaceutical industry for biomass monitoring, is carried out successfully. In conclusion, knowledge in micro system technology to build microdevices have been utilised to manipulate and characterise beads and cells, taking one step further towards viable Lab-on-Chip instruments.

In this master work, we investigated the feasibility of a magnetic resonance measurement technique using magnetic nanoparticle dispersions in both liquid and solid form. The implementation is realised as a coplanar waveguide operating in the frequency range of 0.5 - 20 GHz and an electromagnet producing a static magnetic field of strength up to 1.2 T. The Gilbert magnetic damping factor is determined for polymer composites of magnetic nanoparticles and the gyromagnetic ratio is determined for both nanoparticle dispersions in liquid form and polymer composites.