The aim of this project is detection of gass leak based on the ultrasound sensing. Work introduces ultrasound, mechanism of its propagation and attenuation. From all of the available microphones, the piezoelectric microphone was chosen. Project continues with description of the device, which can be capable of detection of the ultrasound leakage in dangerous, explosive environment. This type of device must meet requirements of SIL 2 standard and ATEX directive for zone 2. Project discusses LNA (Low Noise Amplifier), filters and detection circuits design. The device is modular what means that each module can be freely replaced. The role of these modules is to convert analog signal to digital form suitable for microcontroller HERCULES TSM57012.

This master’s thesis describes the design, implementation and testing of an active antenna intended for use with global navigation satellite systems. The active antenna is composed of two major parts, a dual-band circular patch antenna and a dual-band low-noise amplifier. To streamline the design process, a modular solution was adopted. This enabled the functionality of every part in the signal path to be verified before the final active antenna was designed. A practical method to develop dual-band stacked circular patch antennas, along with a systematic way to tune the resonant frequencies and impedance of the antenna, is also presented. Testing of the antenna in realistic scenarios shows that the active antenna performs as expected and predicted by simulations. / <p>Examensarbetet är utfört vid Institutionen för teknik och naturvetenskap (ITN) vid Tekniska fakulteten, Linköpings universitet</p>

Yes / This paper presents an approach to implement an automatically tuning antenna for optimising power transfer suitable for software defined radio (SDR). Automatic tuning is accomplished using a closed loop impedance tuning network comprising of an impedance sensor and control unit. The sensor provides the control unit with data on the transmit or receive power, and the algorithm is used to impedance of a T-network of LC components to optimize the antenna impedance to maximise power transmission or reception. The effectiveness of the proposed tuning algorithm in relation to impedance matching and convergence on the optimum matching network goal is shown to be superior compared with the conventional tuning algorithm. / This work is partially supported by innovation programme under grant agreement H2020-MSCA-ITN-2016 SECRET-722424 and the financial support from the UK Engineering and Physical Sciences Research Council (EPSRC) under grant EP/E022936/1

No description available.

No description available.

The performance of III-V heterojunction bipolar transistors (HBTs) has improved significantly over the past two decades. Today’s state of the art Indium Phosphide (InP) HBTs have a maximum frequency of oscillation greater than 800 GHz and have been used to realize an amplifier operating above 600 GHz . In comparison to silicon (Si) based devices, III-V HBTs have superior transport properties that enables a higher gain, higher speed, and noise performance, and much higher Johnson figure- of-merit . From this perspective, the InP HBT is one of the most promising candidates for high performance mixed signal electronic systems.

The ever increasing diversity in communication systems has created a demand for constant improvements in receiver components. This thesis describes the design and characterisation of front-end receiver components for various challenging applications, including characterisation of low noise foundry processes, LNA design and multi-band antenna design. It also includes a new theoretical analysis of noise coupling in low noise phased array receivers.In LNA design much depends on the choice of the optimum active devices. A comprehensive survey of the performance of low noise transistors is therefore extremely beneficial. To this end a comparison of the DC, small-signal and noise behaviours of 10 state-of-the-art GaAs and InP based pHEMT and mHEMT low noise processes has been carried out. Their suitability in LNA designs has been determined, with emphasis on the SKA project. This work is part of the first known detailed investigation of this kind. Results indicate the superiority of mature GaAs-based pHEMT processes, and highlight problems associated with the studied mHEMT processes. Two of the more promising processes have then been used to design C-band and UHF-band MMIC LNAs. A new theoretical analysis of coupled noise between antenna elements of a low noise phased array receiver has been carried out. Results of the noise wave analysis, based on fundamental principles of noisy networks, suggest that the coupled noise contribution to system noise temperatures should be smaller than had previously been suggested for systems like the SKA. The principles are applicable to any phased array receiver. Finally, a multi-band antenna has been designed and fabricated for a severe operating environment, covering the three extremely crowded frequency bands, the 2.1 GHz UMTS, the 2.4 GHz ISM and the 5.8 GHz ISM bands. Measurements have demonstrated excellent performance, exceeding that of equivalent commercial antennas aimed at similar applications.

Les systèmes de communication mobiles permettent l’utilisation de l’information en environnements complexes grâce à des dispositifs portables qui ont comme principale restriction la durée de leurs batteries. Des nombreux efforts se sont focalisés sur la réduction de la consommation d’énergie des circuits électroniques de ces systèmes, une fois que le développent des technologies des batteries ne avance pas au rythme nécessaire. En outre, les systèmes RF sont généralement conçus pour fonctionner de manière fixe, spécifiés pour le pire cas du lien de communication. Toutefois, ce scénario peut se produire dans une petite partie du temps, entraînant ainsi en perte d’énergie dans le reste du temps. La recherche des circuits RF adaptatifs, pour adapter le niveau du signal d'entrée pour réduire la consommation d'énergie est donc d'un grand intérêt et de l'importance. Dans la chaîne de réception radiofréquence, l'amplificateur à faible bruit (LNA) se montre un composant essentiel, autant pour les performances de la chaîne que pour la consommation d'énergie. Au cours des dernières décennies, des techniques pour la conception de LNAs reconfigurables ont été proposées et mises en oeuvre. Cependant, la plupart d'entre elles s’applique seulement au contrôle du gain, sans exploiter Le réglage de la linéarité et du bruit envisageant l'économie d'énergie. De plus,ces circuits occupent une grande surface de silicium, ce qui entraîne un coût élevé, ou NE correspondent pas aux nouvelles technologies CMOS à faible coût. L'objectif de cette étude est de démontrer la faisabilité et les avantages de l'utilisation d'un LNA reconfigurable numériquement dans une chaîne de réception radiofréquence, du point de vue de la consommation d'énergie et de coût de fabrication. / Mobile communication systems allow exploring information in complex environments by means of portable devices, whose main restriction is battery life. Once battery development does not follow market expectations, several efforts have been made in order to reduce energy consumption of those systems. Furthermore, radio-frequency systems are generally designed to operate as fixed circuits, specified for RF link worst-case scenario. However, this scenario may occur in a small amount of time, leading to energy waste in the remaining periods. The research of adaptive radio-frequency circuits and systems, which can configure themselves in response to input signal level in order to reduce power consumption, is of interest and importance. In a RF receiver chain, Low Noise Amplifier (LNA) stand as critical elements, both on the chain performance or power consumption. In the past some techniques for reconfigurable LNA design were proposed and applied. Nevertheless, the majority of them are applied to gain control, ignoring the possibility of linearity and noise figure adjustment, in order to save power. In addition, those circuits consume great area, resulting in high production costs, or they do not scale well with CMOS. The goal of this work is demonstrate the feasibility and advantages in using a digitally controlled LNA in a receiver chain in order to save area and power. / Os sistemas de comunicação móveis permitem a exploração da informação em ambientes complexos através dos dispositivos portáteis que possuem como principal restrição a duração de suas baterias. Como o desenvolvimento da tecnologia de baterias não ocorre na velocidade esperada pelo mercado, muitos esforços se voltam à redução do consumo de energia dos circuitos eletrônicos destes sistemas. Além disso, os sistemas de radiofrequência são em geral projetados para funcionarem de forma fixa, especificados para o cenário de pior caso do link de comunicação. No entanto, este cenário pode ocorrer em uma pequena porção de tempo, resultando assim no restante do tempo em desperdício de energia. A investigação de sistemas e circuitos de radiofrequência adaptativos, que se ajustem ao nível de sinal de entrada a fim de reduzir o consumo de energia é assim de grande interesse e importância. Dentro de cadeia de recepção de radiofrequência, os Amplificadores de Baixo Ruído (LNA) se destacam como elementos críticos, tanto para o desempenho da cadeia como para o consumo de potência. No passado algumas técnicas para o projeto de LNA reconfiguráveis foram propostas e aplicadas. Contudo, a maioria delas só se aplica ao controle do ganho, deixando de explorar o ajuste da linearidade e da figura de ruído com fins de economia de energia. Além disso, estes circuitos ocupam grande área de silício, resultando em alto custo, ou então não se adaptam as novas tecnologias CMOS de baixo custo. O objetivo deste trabalho é demonstrar a viabilidade e as vantagens do uso de um LNA digitalmente configurável em uma cadeia de recepção de radiofrequência do ponto de vista de custo e consumo de potência.

Les travaux présentés dans ce mémoire d'habilitation portent sur l'impact du bruit de fond électrique sur les technologies des composants actifs, les circuits et les systèmes des hautes fréquences. Durant nos 12 dernières années de recherche, nous nous sommes notamment intéressés à des filières émergentes à fort potentiel d'intégration (BiCMOS Silicium-Germanium) ou encore à forte puissance (GaN) : nous avons ainsi développé des modèles électriques (petit signal et fort signal) et en bruit (basse fréquence et haute fréquence) des composants actifs pour identifier les pistes d'améliorations technologiques, pour localiser les défauts structurels ou pour étudier le comportement de ces mêmes défauts après l'application de contraintes simulant un vieillissement accéléré. Sur la base de la connaissance des composants actifs (transistor bipolaire à hétérojonction et transistors à effet de champ), nous avons développé des circuits intégrés MMIC faible bruit à 10 GHz et 20 GHz (amplificateurs et oscillateurs) dont certains se positionnent à l'état de l'art : des comparaisons de topologies ont notamment été réalisées sur différentes versions intégrées d'oscillateurs contrôlés en tension de type MMIC SiGe. Nous proposons également une discussion sur la pertinence des facteurs de mérite usuellement employés. D'autres études sur des atténuateurs programmables MMIC SiGe ont fait l'objet de brevets. La troisième partie, orientée système, aborde l'étude du bruit d'un récepteur : nous traitons ainsi le cas d'un étage de réception affecté par la chaîne d'émission, en proposant différentes parades permettant de limiter les dégradations de son plancher de bruit ; une technique de filtre compact intégré à l'amplificateur faible bruit a ainsi été brevetée. Enfin, le cas d'un système de liaison hertzienne embarqué sur automobile est abordé. Diverses stratégies sont ainsi proposées pour pallier les évènements conduisant à une rupture de la liaison (diversité temporelle, diversité spatiale et diversité de polarisation). Ces études reposent sur une approche mixte de traitement de mesures par des modèles théoriques, et des simulations électromagnétiques.

Ultra wide band (UWB) is an extremely promising wireless technology for researchers and industrials. One of the most interesting is its high data rate and fading robustness due to selective frequency fading. However, beside such advantages, UWB system performance is highly affected by existing narrowband interference (NBI), undesired UWB signals and tone/multi-tone noises. For this reason, research about NBI cancellation is still a challenge to improve the system performance vs. receiver complexity, power consumption, linearity, etc. In this work, the two major receiver sections, i.e., analog (radiofrequency or RF) and digital (digital signal processing or DSP), were considered and new techniques proposed to reduce circuit complexity and power consumption, while improving signal parameters. In the RF section, different multiband UWB low-noise amplifier key design parameters were investigated like circuit configuration, input matching and desired/undesired frequency band filtering, highlighting the most suitable filtering package for efficient UWB NBI cancellation. In the DSP section, due to pulse transmitter signals, different issues like modulation type and level, pulse variety, shape and color noise/tone noise assumptions, were addressed for efficient NBI cancelation. A comparison was performed in terms of bit-error rate, signal-to-interference ratio, signal-to-noise ratio, and channel capacity to highlight the most suitable parameters for efficient DSP design. The optimum number of filters that allows the filter bandwidth to be reduced by following the required low sampling rate and thus improving the system bit error rate was also investigated.