Le déploiement des répéteurs iso-fréquence est une solution économique pour étendre la couverture d’un émetteur principal aux zones d’ombre. Cependant, ce mode de déploiement fait apparaître le phénomène des échos radio-fréquence entre antennes d’émission et de réception du répéteur. Selon les standards, un écho aussi faible soit-il réduit le débit de la liaison radio, tandis qu’un écho fort fait courir au répéteur le risque d’endommager ses circuits électroniques, ces risques sont dûs aux ondulations de puissance créées par les échos. L’objectif de cette thèse à caractère industriel est d’étudier ce phénomène naturel en considérant des signaux provenant de différents standards des télécommunications. Cette étude permet une caractérisation des échos radio-fréquence pour mieux s’orienter vers une solution optimisée et industriellement réalisable.Nous nous sommes orientés vers la solution du traitement du signal avancé en favorisant le filtrage adaptatif pour sa rapidité de convergence et sa simplicité relative d’implantation matérielle. Les circuits reconfigurables sont retenus pour leur prix et leur souplesse. L’implantation des solutions est effectuée en virgule fixe afin de satisfaire les exigences de réactivité. Durant la mise en oeuvre de la solution anti-écho, nous avons proposé une multitude de solutions numériques souples et fiables. À partir de ce constat, notre partenaire industriel a décidé de généraliser ce mode de traitement par le développement, la fabrication et la commercialisation de répéteurs de nouvelle génération entièrement numériques. / On-frequency repeaters are a cost-effective solution to extend coverage and enhance wireless communications, especially in shadow areas. However, coupling between the receiving antenna and the transmitting antenna, called radio frequency echo, increases modulation errors and creates oscillations in the system when the echo power is high. According to the communication standards, extremely weak echoes decrease the transmission rate, while strong echoes damage electroni ccircuits because of power peaks. This thesis aims at characterizing the echo phenomenon under different modulations, and proposing an optimized solution directly integrated to industry. We have turned to digital solutions especially the adaptive because of their high convergence rate and their simplicity to be implemented. The programmable circuits are chosen for their attractive price and their flexibility. When implementing echo cancellation solution, we proposed several reliable solutions, showing that digital processing is much more beneficial. For this reason, digital solutions are generalized, and the new generation of repeaters is fully digital.

L'amplificateur de puissance est le module le plus critique dans les équipements de communication radio. Il détermine la qualité de la liaison par sa linéarité et a une contribution conséquente dans la consommation de l'émetteur ; environ 60% de l'énergie consommée est consacré à l'amplification. Il est donc crucial de le faire fonctionner avec un rendement énergétique élevé. Cependant, ces deux spécifications principales de l'amplificateur que sont la linéarité et le rendement énergétique sont antagoniques. Par conséquent, la conception d'un module d'amplification de puissance suppose de trouver un compromis entre la linéarité et le rendement. L'optimisation de ce compromis est la raison d'être des techniques de linéarisation d'amplificateurs et d'amélioration du rendement, parmi lesquelles la prédistorsion numérique (DPD) et les techniques de réduction du PAPR du signal (CFR).Le cœur de cette thèse est la linéarisation d'amplificateurs RF haute-puissance et large-bande par prédistorsion numérique (DPD). Dans ces travaux, nous abordons trois problématiques liées à la prédistorsion et qui constituent des verrous technologiques importants. Le premier aspect concerne l'implémentation de la prédistorsion numérique dans un contexte multi-bande où le signal à linéariser comporte plusieurs formes d'ondes, situées à des fréquences différentes. La seconde problématique est l'utilisation conjointe de la prédistorsion avec une technique de CFR. Dans la majorité des applications haute-puissance, les techniques de DPD et de CFR sont présentes de manière complémentaire, cependant elles sont utilisées de façon autonome et disjointe. Celles-ci gagneraient en performances de linéarisation en étant implémentées de manière plus concertée. . Le dernier thème abordé par cette thèse est l'effet des désadaptations d'impédance de l'antenne sur le mode de fonctionnement de l'amplificateur. La variation de l'impédance d'antenne entraine des réflexions de signal vers l'amplificateur qui modifient ses spécifications de linéarité et de rendement. Nous améliorons la linéarité du système DPD + AP, lorsque l'amplificateur est soumis à des variations de l'impédance à sa charge, grâce à une correction adaptative de gain / Power amplifier is one of the most critical element within radiocommunications systems. The PA is their main source of nonlinearities and it has a great contribution on the emitter's power consumption. Running the PA with highest power efficiency is thus as crucial as having it linear for a good communication quality. However these two specifications of the PA are antagonistic and PA manifacturers need to find a compromise between linearity and power efficiency. Digital Predistortion (DPD) and Crest factor Reduction techniques are intended to improve power efficiency while preserving linearity or inversely. Linearization of wideband RF power amplifiers using Digital Predistortion is the focus of this thesis. Three DPD issues are investigated in these works. The first issue deals with multiband linearization where signals with various waveforms located at different frequency bands are amplified. The second objective of this thesis is to study a concurrent DPD/CFR systems based on an automatic estimation of the necessary CFR gain. The last part of this dissertation deals with PA linearization under antenna load variations. Indeed, the impedance of antenna may vary because of electromagnetic objects that are present in its vicinity. Those impedance variations may instigate signal reflections toward the PA, that modify some of its main specifications (linearity, delivered power and efficiency). Our goal in this field is to preserve DPD linearization performances under antenna load mismatch

High-speed digital-to-analog converters are critical components in many radiofrequency (RF) applications. The resistive DAC (RDAC) architecture is suitable for high-speed implementation in extremely scaled digital circuit nodes. An RDAC core can be implemented as a resistance network and a digital block, consisting of inverters as drivers to the resistive network. One disadvantage of the architecture is the input code-dependent supply current. Combined with a non-zero supply network impedance, the code-dependent current will introduce non-linearity in the output voltage. One way to circumvent the problem is to use a high-performance voltage regulator, which counteracts the voltage variation in the impedance in the RDAC supply network. In this thesis work, two alternative solutions are investigated; Compensation with another signal-dependent impedance in parallel with the RDAC core to reduce the impedance variations and a digital predistorter (DPD) which corrects the non-linearities of RDAC output voltage. The investigated techniques can be used for improving the linearity of an RDAC in certain cases. The current compensation technique works best at low frequencies, while the DPD can be used for all frequencies to relax requirements on routing resistance or voltage regulation design.

Les stations de base à petite échelle (picocellules et femtocellules) seront un des leviers principaux qui permettront d'atteindre l'objectif 1000X, objectif fixé par les grands acteurs du domaine des télécommunications visant à augmenter la capacité des réseaux mobiles sans fil 5G d'un facteur 1000 par rapport aux réseaux 4G. Dans ce type de réseau, l'amplificateur de puissance (PA) est responsable de la majorité de la consommation de puissance de la station de base. Pour minimiser sa consommation de puissance, le PA est polarisé proche de sont point de compression mais avec l'augmentation des largeurs de bande, ce dernier subit des effets de mémoire accrus qui viennent s'ajouter aux problèmes classiques de non-linéarités. Les systèmes de prédistorsion numérique (DPD), et analogique/RF(ARFPD) peuvent être utilisés pour améliorer le compromis linéarité / efficacité des PAs. Cependant pour les pico-cellules et femto-cellules utilisées dans le standard 5G, les prédistorseurs conventionnels ne sont adaptés pour des raisons de complexité et de consommation de puissance.Le modèle "Memory Polynomilal" (MP) est l'un des modèles de prédistorsion les plus attractifs pour modéliser les PAs, fournissant des performances intéressantes avec peu de coefficients. Cependant, la précision de ce modèle se dégrade pour les signaux large bance. Pour palier ce problème, nous proposons un nouveau modèle, le FIR-MP qui combine un filtre FIR au modèle MP classique. Pour valider et quantifier la précision du modèle proposé, nous avons effectué des simulations avec un modèle extrait par mesure de l'amplificateur sur étagère ADL5606 (GaAs 1W HBT PA). Les résultats de ces simulations présentent des améliorations du taux de fuite des canaux adjacents (ACLR) de 7,2 dB et 15,6 dB, respectivement, pour des signaux à 20 MHz et 80 MHz par rapport au modèle MP classique. Le FIR-MP a été également synthétisé en technologie CMOS FDSOI 28 nm. Les résultats de la synthèse ont donné une puissance globale de 9,18 mW and 116,2 mW, respectivement, pour les signaux de 20 MHz and 80 MHz.Basé sur le modèle proposé de FIR-MP, une nouvelle approche à signaux mixtes pour linéariser les PAs a été aussi étudiée. En fait, le filtre numérique FIR améliore la performance de correction de la mémoire sans aucune expansion de la bande passante et la linéarisation en bande de base permet d'éviter l'utilisation de composants RF dans la linéariseur. Ainsi, les contraintes en bande passante requises pour le DAC, les filtres de reconstruction et les blocs RF de l'émetteur sont relâchées comparés aux techniques conventionnelles de linéarisation numériques et RF. Nous avons ainsi étudié l'impact des diverses non-idéalités en utilisant un signal modulé à 80 MHz afin de dériver les exigences pour la mise en œuvre du circuit. Les simulations ont montré qu'une résolution de 8 bits pour les coefficients et un SNR de 60 dB sont nécessaires pour atteindre un ACLR1 supérieur à 45 dBc. Ces résultats constituent un premier signe favorable dans l'optique d'une implémentation matérielle de la solution proposée, étape indispensable pour évaluer précisément sa consommation de puissance et sa complexité pour pouvoir la comparer à l'état de l'art des linéariseurs. / Small-cell base stations (picocells and femtocells) handling high bandwidths (> 100 MHz) will play a vital role in realizing the 1000X network capacity objective of the future 5G wireless networks. Power Amplifier (PA) consumes the majority of the base station power, whose linearity comes at the cost of efficiency. With the increase in bandwidths, PA also suffers from increased memory effects. Digital predistortion (DPD) and analog RF predistortion (ARFPD) tries to solve the linearity/efficiency trade-off. In the context of 5G small-cell base stations, the use of conventional predistorters becomes prohibitively power-hungry.Memory polynomial (MP) model is one of the most attractive predistortion models, providing significant performance with very few coefficients. We propose a novel FIR memory polynomial (FIR-MP) model which significantly augments the performance of the conventional memory polynomial predistorter. Simulations with models extracted on ADL5606 which is a 1 W GaAs HBT PA show improvements in adjacent channel leakage ratio (ACLR) of 7.2 dB and 15.6 dB, respectively, for 20 MHz and 80 MHz signals, in comparison with MP predistorter. Digital implementation of the proposed FIR-MP model has been carried out in 28 nm FDSOI CMOS technology. With a fraction of the power and die area of that of the MP a huge improvement in ACLR is attained.An overall estimated power consumption of 9.18 mW and 116.2 mW, respectively, for 20 MHz and 80 MHz signals is obtained.Based on the proposed FIR-MP model a novel low-power mixed-signal approach to linearize RF power amplifiers (PAs) is presented. The digital FIR filter improves the memory correction performance without any bandwidth expansion and the MP predistorter in analog baseband provides superior linearization. MSPD avoids 5X bandwidth requirement for the DAC and reconstruction filters of the transmitter and the power-hungry RF components when compared to DPD and ARFPD, respectively.The impact of various non-idealities is simulated with ADL5606 (1 W GaAs HBT PA) MP PA model using 80 MHz modulated signal to derive the requirements for the integrated circuit implementation. A resolution of 8 bits for the coefficients and a signal path SNR of 60 dB is required to achieve ACLR1 above 45 dBc, with as little as 9 coefficients in the analog domain. Discussion on the potential circuit architectures of subsystems is provided. It results that an analog implementation is feasible. It will be worth in the future to continue the design of this architecture up to a silicon prototype to evaluate its performance and power consumption.

This research work has made an effort to understand a novel line of radio frequency power amplifiers (RFPAs) that address initiatives for efficiency enhancement and linearity compensation to harmonize the fifth generation (5G) campaign. The objective is to enhance the performance of an orthogonal frequency division multiplexing-long term evolution (OFDM-LTE) transmitter by reducing the nonlinear distortion of the RFPA. The first part of this work explores the design and implementation of 15.5 W class AB RF power amplifier, adopting a balanced technique to stimulate efficiency enhancement and redeeming exhibition of excessive power in the transmitter. Consequently, this work goes beyond improving efficiency over a linear RF power amplifier design; in which a comprehensive investigation on the fundamental and harmonic components of class F RF power amplifier using a load-pull approach to realise an optimum load impedance and the matching network is presented. The frequency bandwidth for both amplifiers was allocated to operate in the 2.620-2.690 GHz of mobile LTE applications. The second part explores the development of the behavioural model for the class AB power amplifier. A particular novel, Hammerstein-Wiener based model is proposed to describe the dynamic nonlinear behaviour of the power amplifier. The RF power amplifier nonlinear distortion is approximated using a new linear parameter approximation approach. The first and second-order Hammerstein-Wiener using the Normalised Least Mean Square Error (NLMSE) algorithm is used with the aim of easing the complexity of filtering process during linear memory cancellation. Moreover, an enhanced adaptive Wiener model is proposed to explore the nonlinear memory effect in the system. The proposed approach is able to balance between convergence speed and high-level accuracy when compared with behavioural modelling algorithms that are more complex in computation. Finally, the adaptive predistorter technique is implemented and verified in the OFDM transceiver test-bed. The results were compared against the computed one from MATLAB simulation for OFDM and 5G modulation transmitters. The results have confirmed the reliability of the model and the effectiveness of the proposed predistorter. / Fundacão para a Ciência e a Tecnologia, Portugal, under European Union’s Horizon 2020 research and innovation programme ... grant agreement H2020-MSCA-ITN- 2016 SECRET-722424 I also acknowledge the role of the National Space Research and Development Agency (NASRDA) Sokoto State Government Petroleum Technology Trust Fund (PTDF)

No description available.

Given the ever increasing reliance of today’s society on ubiquitous wireless access, the paradigm of dynamic spectrum access (DSA) as been proposed and implemented for utilizing the limited wireless spectrum more efficiently. Orthogonal frequency division multiplexing (OFDM) is growing in popularity for adoption into wireless services employing DSA frame- work, due to its high bandwidth efficiency and resiliency to multipath fading. While these advantages have been proven for many wireless applications, including LTE-Advanced and numerous IEEE wireless standards, one potential drawback of OFDM or its non-contiguous variant, NC-OFDM, is that it exhibits high peak-to-average power ratios (PAPR), which can induce in-band and out-of-band (OOB) distortions when the peaks of the waveform enter the compression region of the transmitter power amplifier (PA). Such OOB emissions can interfere with existing neighboring transmissions, and thereby severely deteriorate the reliability of the DSA network. A performance-enhancing digital pre-distortion (DPD) technique compensating for PA and in-phase/quadrature (I/Q) modulator distortions is proposed in this dissertation. Al- though substantial research efforts into designing DPD schemes have already been presented in the open literature, there still exists numerous opportunities to further improve upon the performance of OOB suppression for NC-OFDM transmission in the presence of RF front-end impairments. A set of orthogonal polynomial basis functions is proposed in this dissertation together with a simplified joint DPD structure. A performance analysis is presented to show that the OOB emissions is reduced to approximately 50 dBc with proposed algorithms employed during NC-OFDM transmission. Furthermore, a novel and intuitive DPD solution that can minimize the power regrowth at any pre-specified frequency in the spurious domain is proposed in this dissertation. Conventional DPD methods have been proven to be able to effectively reduce the OOB emissions that fall on top of adjacent channels. However more spectral emissions in more distant frequency ranges are generated by employing such DPD solutions, which are potentially in violation of the spurious emission limit. At the same time, the emissions in adjacent channel must be kept under the OOB limit. To the best of the author’s knowledge, there has not been extensive research conducted on this topic. Mathematical derivation procedures of the proposed algorithm are provided for both memoryless nonlinear model and memory-based nonlinear model. Simulation results show that the proposed method is able to provide a good balance of OOB emissions and emissions in the far out spurious domain, by reducing the spurious emissions by 4-5 dB while maintaining the adjacent channel leakage ratio (ACLR) improvement by at least 10 dB, comparing to the PA output spectrum without any DPD.

As wireless communication becomes an ever-more important and pervasive part of our everyday life, system capacity and quality of service issues are becoming more critical. In order to increase the system capacity and improve the quality of service, it is necessary that we pay closer attention to bandwidth and power efficiency issues. Orthogonal Frequency Division Multiplexing (OFDM) is a multicarrier modulation technique for high speed data transmission and is generally regarded as bandwidth efficient. However, OFDM signals suffer from high peak-to-average power ratios (PARs) which lead to power inefficiency in the RF portion of the transmitter. Moreover, in OFDM, the well-known pilot tone assisted modulation (PTAM) technique utilizes a number of dedicated training pilots to acquire the channel state information (CSI), resulting in somewhat reduced bandwidth efficiency. In this dissertation, we will address the above mentioned bandwidth and power efficiency issues in wireless transmissions. To avoid bandwidth efficiency loss due to dedicated training, we will first develop a superimposed training framework that can be used to track the frequency selective as well as the Doppler shift characteristics of a channel. Later on, we will propose a generalized superimposed training framework that allows improved channel estimates. To improve the power efficiency, we adopt the selected mapping (SLM) framework to reduce the PARs for both OFDM and forward link Code Division Multiple Access (CDMA). We first propose a dynamic SLM algorithm to greatly reduce the computational requirement of SLM without sacrificing its PAR reducing capability. We propose a number of blind SLM techniques for OFDM and for forward link CDMA; they require no side information and are easy to implement. Our proposed blind SLM technique for OFDM is a novel joint channel estimation and PAR reduction algorithm, for which bandwidth efficiency power efficiency - complexity - bit error rate tradeoffs are carefully considered.

Many communications signal formats are not power efficient because of their large peak-to-average power ratios (PARs). Moreover, in the presence of nonlinear devices such as power amplifiers (PAs) or mixers, the non-constant-modulus signals may generate both in-band distortion and out-of-band interference. Backing off the signal to the linear region of the device further reduces the system power efficiency. To improve the power efficiency of the communication system, one can pursue two approaches: i) linearize the PA; ii) reduce the high PAR of the input signal. In this dissertation, we first explore the optimal nonlinearity under the peak power constraint. We show that the optimal nonlinearity is a soft limiter with a specific gain calculated based on the peak power limit, noise variance, and the probability density function of the input amplitude. The result is also extended to the fading channel case. Next, we focus on digital baseband predistortion linearization for power amplifiers with memory effects. We build a high-speed wireless test-bed and carry out digital baseband predistortion linearization experiments. To implement adaptive PA linearization in wireless handsets, we propose an adaptive digital predistortion linearization architecture that utilizes existing components of the wireless transceiver to fulfill the adaptive predistorter training functionality. We then investigate the topic of PAR reduction for OFDM signals and forward link CDMA signals. To reduce the PAR of the OFDM signal, we propose a dynamic selected mapping (DSLM) algorithm with a two-buffer structure to reduce the computational requirement of the SLM method without sacrificing the PAR reduction capability. To reduce the PAR of the forward link CDMA signal, we propose a new PAR reduction algorithm by introducing a relative offset between the in-phase branch and the quadrature branch of the transmission system.

The incorporation of Gallium Nitride (GaN) Power Amplifiers (PAs) into future high power aperture radar systems is certain; however, the introduction of this technology into multifunction radar systems will present new challenges to radar engineers. This dissertation describes a broad investigation into amplitude and phase transients produced by GaN PAs when they are excited with multifunction radar waveforms. These transients are the result of self-heating electrothermal memory effects and are manifested as interpulse instabilities that can negatively impact the coherent processing of multiple pulses. A behavioral model based on a Foster network topology has been developed to replicate the measured amplitude and phase transients accurately. This model has been used to develop a digital predistortion technique that successfully mitigates the impact of the transients. The Moving Target Indicator (MTI) Improvement Factor and the Root Mean Square (RMS) Pulse-to-Pulse Stability are used as metrics to assess the impact of the transients on radar system performance and to test the effectiveness of a novel digital predistortion concept. / Ph. D.